ADDN/ALTN AND SPECIAL REPAIR TO 20 QTRS OF OFFRS MD ACCN AT PARTAP CHOWK UNDER GE (CENTRAL), DELHI CANTT-10

Amount

B/R WORK

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified.

M & L for 40 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floors surface finished even and smooth using extra cement complete all as specified.

Supply only glass dividing strips, 38mm wide and 3mm thick and inserted in position to conform to design complete all as specified.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished fair and even without using extra cement complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) including removal of rubbish outside complex ( MOD land) complete all as specified.

M&L reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

M&L form work to chajja, weather shade, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified.

S&F TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0 complete all as specified.

All as per item 9 above but 6mm to 8mm dia

Dismantling of brick work built in cement mortar in any description and position, complete all as specified.

M&L for brick work with sub class 'B' brick straight or curved on plan exc 6 metre mean radius with old size bricks, built in cement mortar 1:6, complete all as specified.

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls with old size bricks, built in cement mortar 1:4, complete all as specified.

M&L for cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) as in blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces, complete all as specified upto double storey height.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing admixture finished even and smooth without using extra cement complete all as specified. (Note :- Water proofing admixture shall be measured and paid separatelly).

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing admixture finished even and smooth without using extra cement including taking down old plaster complete all as specified. (Note : Water proofing admixture shall be measured and paid separatelly).

Supply only integral water proofing admixture of approved quality.

M & L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces in ceiling, chajja and like surface finished even and smooth without using extra cement including taking down old plaster complete all as specified.

M&L for Preparation of new surfaces (Plastered or un-plastered) on ceiling and applying three coats of white lime wash complete all as specified.

M & L for removing existing treatment of ceiling with mechanical grinder and applying putty (2-3 mm) and preparation of old decorated surface(Plastered or unplastered) of ceiling by brooming down or steel wire brushing scraping down smoke root mould moss and efforescent salts and treating oil and greasy spots as applicable and applying two coat of white wash complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement including taking down old plaster complete all as specified.

M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying three coats of white lime wash over a coat of alkali resistant primer complete all as specified.

M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying two coats of oil bound distemper(white or tinted) over a coat of 2 to 3mm thick chalk whitning wall putty over one coat of alkali resistant primer on plastered surfaces, complete all as specified.

M&L for Preparation of old decorated surfaces(Plastered or unplastered) of wall including cornices, pillasters etc by complete removal of existing treatment and applying two coats of white lime washing over putty (2-3 mm), complete all as specified.

M&L for preparation of old decorated surface (plastered or unplastered) of walls/ceilings by complete removal of existing treatment by mechanical grinder and applying two coat of oil bound distemper over a coat of 2 to 3 mm thick wall putty over one coat of alkali resistant primer on plastered surfaces of walls complete all as specified .

M&L Easing of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

Taking down chowkats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from frames) complete all as specified.

Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames ) complete all as specified.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each complete all as specified.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each and refixing in same opening complete all as specified.

M&L for 2nd class hardwood plain, solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified.

S& F 35 mm thick flush shutters (factory made) solid core construction, with block board core and plywood face pannel, commercial type on both sides. Flush shutters shall have teak wood edging complete all as specified.

S&F 35mm thick 2nd class Hard wood rail & style (factory made) plain, framed, panelled shutter (two panel) with lock rail & panel of 12mm veneered particle board with commercial veneering on both sides. The size of rail & style as per IS :1003 (Part I), Kilan seasoned & chemicals pressure treated, complete all as specified.

M&L for 35 mm thick 2nd class hard wood glazed and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat complete all as specified.

M & L Fibre galss reinforced plastic (FRP) door frames shall be three lagged of cross section 90mm x 45 mm having single rebate of 32mm x 15mm to receive shutter of 30 mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. MS stay shall be provided at the bottom to steady the frame.

M & L FRP door shutter shall be 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufactures. Made with fire retardant grade unsaturated polyester resin moulded to 3mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP panels and confirming to IS 14856-2000.

S & F in repairs factory made solid panel PVC door shutter 30 mm thick (style) consisting of framee made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Cutting holes in brick wall built in cement mortar for inserting hold fasts, depth of embedded postion of hold fast /lugs measured from the face the jambs into the wall exc half brick but n.exc one brick thick and making good the dismantled portion in cement mortar 1:3 or in cement concrete 1:2:4 type B-1, using 20mm graded stone agg complete all as specified upto six storey height.

S&F mild steel work as in hold fast 25x3mm flat iron and similar articles conforming to Fe-410-0, complete all as specified.

Dismantling boarding any description (board/plywood) fixed in any position with screw, complete all as specified

M&L for 18/19mm thick block veneered board core grade 2 quality,interior grade,commercial type, fixed with screws to timber frame work as in cup board shutter, loft shutters incl 15mm thick teak wood leaping and necessary rebating for leaf shutters where required including polishing to leaping/rebating complete all as specified.

S&F factory made PVC frame of size 75x40mm with wall thickness of 4mm made out of extruded 4mm thick plain or prelam PVC sheet reinforced with 15x15mm MS square tube of 19 gauge thickness through out the frame and mitred cut and two corners and jointed with two nos of 150mm long bracket of 10x10mm MS Square tube. The door frame shall be fixed to the wall using 65x100mm long MS screws though the frame by using PVC fastners minimum of four Nos of screws to be provided for each vertical members and minimum of two nos of screws to be provided horizintal members etc complete all as per manufacture instructions and as directed.

S&F 18/19mm thick PVC moulded solid board one side prelam for cabinet boxes, cupboards etc with self and shutter full size fitted under/above the kitchen cooking platform and other platform complete all as specified and directed as per drg including provn of fixing arrangement

Providing and fixing factory made UPVC any colour fixed window/ventilator area n exc 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 58mm), T Profile ( One vertical length in between two shutters) (60mm x 74mm).Glazing bead (35mm x 20mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (28mm x 21.5) , sash (31mm x 27.5mm), T Profle (27mm x 17mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners including 5mm thick toughened glass with single glazing bead and weather seal and required accessories. Note: Net opening will be measured for payment purpose.

Providing and fixing factory made UPVC any colour casement (Double rebated) window area n exc 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (110mm x 38mm), Glass Sash (60mm x 78mm) another mesh sash (50mm x 77mm),T Profile ( One vertical length in between two shutters) (60mm x 74mm).Glazing bead (35mm x 20mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (26mm x 10mm) , sash (31mm x 27.5mm), T Profle (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners. Hardware (Casement handle made of zinc alloyed (any colour powder coated), transmission gear made of mild steel with multi point locking system ) 5mm thick toughened glass with single glazing bead and weather seal , Stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and required accessories. Note: Net opening will be measured for payment purpose.

Providing and fixing factory made UPVC any colour sliding window Three track of area n exc. 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (88mm x 52mm), Sliding sash (42mm x 67mm), Sliding mesh sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm).Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (30mm x 18) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners. Hardware (Touch lock of zinc alloyed (any colour powder coated), steel roller system, including 5mm thick toughened glass with single glazing bead and weather seal , Stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and required accessories). Note: Net opening will be measured for payment

S&F 100 mm long (size) butt hinges, medium weight cold rolled stainless steel of AISI 304 ISI marked complete all as specified.

S&F continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30 mm, complete all as specified.

S&F in repairs 75 mm long L Bihari concealed type hydrauilc hinges including stainless screw complete all as specified.

S & F in repairs 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified.

S & F 300 mm long, Mild Steel sliding door bolts,plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S&F 150mm long mild steel barrel tower bolts stove enamelled black with bright bolt & fixed with screws, complete all as specified.

S&F 150mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified.

S&F stainless steel of floor door stopper with hard drawn steel spring 140 mm long ,complete all as specified.

S&F Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified

S&F 5.5 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm each including grinding of edges for crockery cupboard including taking out/ broken glass with roller, complete all as specified.

S&F mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

S&F in repair mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

Dismantling of existing wooden pelmet box of any description and size and making good the disturbed surface to match with the existing complete all as specified.

S&F drapery curtain rods extruded aluminum section anodized in gold , copper or antique silver 25 mm nominal dia of approved quality with two number decorative brackets design as approved fixed in brick/concrete wall with same finished knobs/latto on each end of curtain rod complete all as required and directed

M&L for Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L for Praparation of old painted surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified.

M&L for coloured glazed ceramic tiles 300x600 x 7 to 8mm thick as in vertical surfaces of wall as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 all as directed.

M&L for coloured ceramic tiles (Non skid) of size 300x300x 6 to 7mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as directed.

M&L for Vitrified ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed

All all as per 68 above but over and including 10mm thick rendering in CM 1:4 as in skirting all as directed.

M&L for 20 mm thick pre-polished black granite stone work( table rubbed and polished) laid over and including 15 mm thick screed bed or bedding layer in CM 1:4 as in steps, Jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, front and side of slab moulded and polished complete all as specified and directed by Engr in Charge. Granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of stone slab and provn of hole for gas pipe shall be provided. .

M&L Machine cut kota stone slab flooring 20-22 mm thick ( minimum 20mm thick ) over and including 20 mm thick screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and treating the surface with beeswax polish complete over cooking platform in single piece of rounding edges all as specified and directed.

M&L for 20-22 mm thick (minimum thickness 20 mm ) kota stone slab in riser of steps, skirting, dado and pillar laid over and including 10 mm thick rendering in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18 to 20mm thick Udaipur green marble laid over and including 15mm thick screed bed in cm 1:6 as in treads and steps in one piece including cutting, jointing, moulding and granite polishing, laid in designed complete all as specified and directed.

M&L for 18 to 20mm thick Udaipur green marble laid over 10 mm thick rendering in CM 1:4 as in treads/dado etc and steps including cutting, jointing, moulding and granite polishing, laid in designed all as specified and directed.

Taking up or down 15 mm dia GI tubing and connections complete all as specified and directed.

Taking up or down 20 mm dia GI tubing and connections including cleaning for re-fixing, ccomplete all as specified and directed.

S&F 15mm dia GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors, pipes should be painted with bituminous paint of approved quality complete all as specified and directed.Note: Pre form, rigid, resin bonded glasswool section of any length to be used for geyser pipe insulation.

S&F 20mm dia GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F in Soft closing ball bearing telescopic channel of size 22" long fixed with screws in cupboards including all fittings complete all as specified and directed by Engr in charge. Note : Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs.

S&F Modular Cabinet Kitchen accecories of Stainless steel grade - 304, 6mm size rod thickness including :-(i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) of size as per site requirement all as specified and directed by Engr in charge. Make : Godrej Interio/Devas Steel Industries/Zuari Furniture/Sleek/Spacewood/Tiara/Ikea or equivalent make approved by GE.

S&F 25mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

Dismantling of 75 mm bore cast iron pipe (soil/waste/vent) with fittings etc fixed to walls,ceiling, on floors & from trenches if required including taking out any type of joints complete all as specified and directed.

Dismantling of 100 mm bore cast iron pipe (soil/waste/vent) with fittings etc fixed to walls,ceiling, on floors & from trenches if required including taking out any type of joints complete all as specified and directed

S & F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified and directed.

S & F 100 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified and directed.

S&F in repair 100 mm dia (bore of pipe) cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified and directed.

All as per item 86 above but fitted with oval access door for 100mm dia (bore of pipe).

S&F in repair 75mm dia (bore of pipe) cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

All as per item 88 above but fitted with oval access door for 75 mm dia (bore of pipe)

S & F 75mm dia (bore of pipe) Cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified and directed.

S & F 100 mm dia (bore of pipe) Cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified and directed.

S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, ccomplete all as specified and directed.

S&F in repair Salt Glazed Stone Ware (SGSW) gully traps square or round mouthed type size 150x150mm including excavation/earth work, bed concrete, surrounding concrete and CI grating, complete all as specified and directed.

S&F in repair vitreous China coloured European type WC with "P" or "S" trap 1st quality including connection to drain and fixing bolts complete all as specified and directed

S&F PVC (SWR) WC connector with lip ring or bend type of 110 mm bore as required complete all as specified and ddirected

S&F in repair 10 ltrs capacity PVC colour low level flushing cistern (dual type) with PVC flush pipe 32mm dia complete all as specified and directed.

S & F in repair Plastic water closet seat, any colour closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

S & F Brass CP health faucet Hand Shower (Health Faucet) with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed.

Supply & fix in repair CP connection pipe of 1/2"x18" size with 2 Nos brass check nuts with washers, complete all as specified and directed.

Supply & fix in repair PVC connection 15 mm size with PTMT nuts of length 600 mm long complete all as specified and directed.

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 560mm x 470mm complete including , CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "p"or "S" trap front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified and directed .

S&F in repair fancy type brass chromium plated toilet paper holder, complete all as specified and directed

S&F in repair fancy type brass chromium plated soap dish, complete all as specified and directed.

S&F in repair CP grating 125mm dia, complete all as specified and directed.

S&F in repair aluminium peg set of 6 peg, 45 centimeter long, complete all as specified and directed.

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified and directed

S&F in repair fancy type chromium plated brass two way angle valve suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair fancy type 15mm dia chromium plated wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes complete all as specified and directed.

S&F in repair fancy type 15mm bore chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as specified and directed.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed.

S & F in repair fancy type 150mm size square brass CP shower rose complete all as specified and directed.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP brackrt gaurd and railling 60 cm long complete all as specified.Make: Cardin or Equivalent

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified and directed.

S&F in repair fancy type glass corner 250mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified and directed.

S&F in repair fancy type stainless steel towel rack size 600mm X 300mm including apair of brass bracket complete all as specified &directed

S&F stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as specified and directed.

S&F in repairs bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified and directed.

S&F in repair stainless steel sink with drainage board of AISI 316 grade made out of 1.00 mm thick sheet for kitchen with plug, washers, waste pipe including connecting union overall size 1145mm x 510mm x 200mm with bowl size 510mm x 400mm x 200 mm including taking out existing china ware sink with waste fittings complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of AISI 316 grade made out of 1.00 mm thick sheet , size 90x80x25cm including taking out existing wooden plat rack complete all as specified and directed

Dismantling of PVC water tanks of capacity exc 500 litres and n.exc 1000 litres capacity of any condition or type complete all as specified and directed.

Dismantling of PVC water tanks of capacity exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

S & F 1000 ltr capacity rotational moulded polyethylene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S & F 500 ltr capacity rotational moulded polyethylene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed (Minimum wt 20mm-210grm ) complete all as specified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F Steel windows and ventilators with side hung glazed and wiremesh shutters with Z section including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded. Note : - Net opening will be measured for payment.

S & F in repairs 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane made with 1.00 mm thick sheet complete all as specified and directed.

(a) Dismantling of floor size not exc 4.00 Sqm for EWC Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

(a) Dismantling of floor size not exc 1.50 Sqmtr for IWC Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Dismantling of MS grill of parapet railing, any description not otherwise provided for upto six storey height complete all as specified and directed.

S & F MS framed work such as grills, gratings etc with ends of bars shouldered and or riveted, framed guard bars, barred iron doors, ladders, frame work of water trough, railings,cooler stand and similar work to conforming to Fe -290-0 ornamental design, upto six storey height complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer, complete all as specified and directed.

M&L for Preparation of old painted surfaces of steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint, complete all as specified and directed.

M & L for providing precast reinforced cement concrete jallies 45 mm thick including all mouldings type B-0 1:2:4(12.5mm graded stone aggreagte) set in cement mortar 1:4 complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C 2 (using 40mm graded stone aggregate) as in sub base, hard standing complete all as specified and directed.

M&L for 22 to 25mm rubber moulderd ultra tiles over 15 mm thick screed bed in cm 1:6 and jointed and pointed in white cement mixed with pigment to match the shade of tiles of flooring complete all as specified and directed.

Cutting shrubs wild growth, plants not exc 30 cm girth grown on permanet structures and removing same growth right from roots and stopping the recurrence by injecting herbicide Glyphosphate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufactureres intructions. The disturbed area shall be repaired with PCC (1:2:4) Type B0 mix and surface finished even and smooth in cm 1:4 incl applying two coats of matching finish i.e. OBD/exterior acrylic emulsion paint of same shade & finish. Likely minmum number of shrub/plants in each Building is not less than 50 and Work in high rise building upto six storied complete all as specified and directed.

M&L for Preparation of new plastered surface of walls and applying two coats of external weather proof paint over a coat of primerand including a coat of wall putty on plastered surface on walls/ceiling, complete all as specified and directed.

M&L for complete removal of existing old surfaces of wall/ceiling by scrubbing with wire brush , hard brush and applying two coats of weather proof exterior acrylic emulsion paint over a coat of 2mm thick wall care putty complete all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of cement based paint complete all as specified and directed

M & L for preparing new plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100 mm internal dia pipe complete all as specified and directed

Dismantling of brick tiles or terracing tiles single layer on roof and removing the rubbish outside complex (MOD land),including removal of vegetation if any complete all as specified and directed.

Demolition of mud in roof, any thickness, including mud plastering and mud phuska under brick tiles at any situation and height, complete all as specified.

M&L for PCC 1:2:4 (using 20mm graded aggregate) type B-1 as in levelling course using WPA finished even and smooth without using extra cement ( Note : WPA shall be measured and paid seperately)

M&L for APP based polymeric membrane mineral slate finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints

M & L for supreme quality Heat Resistant Terrace Tiles of size 250x250x 20mm thick ,tiles are specially developed to integrate seamlessly with the concrete roof to provide an efficient solution for hot climatic conditions for residential accommodation. The eco efficient tiles are made from premium grade materials under strict quality supervision. Further, these easy to install tiles are suitable for retrofitting projects over 15mm thick screed in CM 1:4 complete all as specified and directed. Note : - Make of tile will be best quality as approved by GE

M & L Cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops etc including weathering slightly rounded or chamfered edges, finished even and smooth without using extra cement including form work complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sides description of column to full height , three sides description of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Suupply and applying of rust removal chemical to Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed. (vii) cleaning of all exposed bars (new & old) alround (viii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (ix) Apply two coa+E149ts of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- upto 12 mm dia bar - drilling length 80 to 120 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar of approved make with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc complete all as specified and directed (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto six storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded mesh to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

SEWAGE DISPOSAL

Excavation in trenches, any type of soil n exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sq m on plan and n exc 1.5 m in depth and getting out.complete all as specified and directed.

All as per 158 here in before but in hard rock

Demoition of breaking up drain pipes (Salt, glazed stoneware, asbetos cement or reinforced concerete set in cement mortar internal dia of pipe 150mm complete all as specified and directed.

Returning filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified and directed.

Removing excavated materials to a distance exc 1.50 km but not exc 5 Km outside defence land and depositing where directed.

M&L PCC 1:4:8 type D2 using 40mm graded stone aggregates as in foundation of manholes, posts etc complete all as specified and directed

M&L PCC 1:2:4 type B2 using 40mm graded stone aggregates as in surface, channels and drain complete all as specified and directed

S&F Stainless steel grill(Grade- 304) using 10mm thick square bars ( 100 mm C/C) of weight not less than 0.62 kg/RM including necessary frame and accessories for window and ventilator grill complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in bedding to drain pipe 150 mm dia including packing under, and haunching against the sides of the pipes after they are laid and tested including form work complete all as specified and didrected.

S&F DWCPE (SN4) 150 mm dia (Internal Dia) pipes, snap fit coupler and rubber ring laid properly and jointed in trenches to a level on concrete bed including testing comple all as specified and directed. Note : The DWCPE (SN4) pipe shall conform to IS 14930 and of best quality as approved by GE. The DWCPE shall consisst of two layers. The outer layer will be corrugated and inner layer shall be plain and smooth. DWCPE pipe and fitting with the scope of this specification shall be so designed and constructed that in normal use their performance is reliable and without damage to the user or surrounding and shall be laid as per manufacturer instructions.

Description of Work / Item(s)

Amount

E/M WORK

Taking down carefully copper/aluminium point wiring (light/fan/ socket/power) complete from the wall by cutting/ chasing including fittings and fixtures such as switches, ceiling roses, pendants holder, regulators,sockets,light fittings etc for credit and making good the disturbed surfaces of wall, floor etc complete all as specified and directed.

Taking down carefully sub main wiring/Service cable of any description.

Disconnecting electric & water supply connections, nuts-bolts & taking down Geyser different capacity and shifting to MES store yard.

Disconnecting elect connection and taking down of ceiling fan / Exaust fan of any make and any height, dismantling blade and removing fan alongwith blade for depositing in MES store yard complete all as specified and directed

Taking down defective switch fuse main board / distribution iron clad or sheet metal enclosure/ MCB DBs with MCBs of any capacity and make including wooden board etc complete all as specified and directed.

M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid new PVC conduit 20 mm dia medium grade ISI Marked and all conduit accessories concealed in wall/ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc , all as specified and as directed for the followings:-

(a) One light /Ceiling fan/exhaust fan point controlled by one, one way switch .

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(d) One bell point controlled by one bell push.

(e) One light point controlled by two Nos two way switches

All as per item No.7 herein before but with 4 sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified and directed. Note for Item 7 & 8 : (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC conduit to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

M&L switch Modular type 6 Amps 230V AC ISI Marked complete all as specified and directed.

M&L switch modular type 6 amp SP two way ISI marked complete all as specified and directed.

M&L Modular socket outlet 5 pin 6 Amp socket 2 module ISI marked complete all as specified and directed.

M&L switch bell push Modular type 6 Amps 1W-1 module ISI marked 230V AC complete all as specified and directed.

M&L switch Modular type 16 Amps 230V AC ISI marked complete all as specified and directed.

M&L Modular socket outlet 5 pin 6/16 Amp universal socket 2 module ISI marked complete all as specified and directed.

Supply & Fix Modular five stepped type electronic fan regulator 1 module 360 degree rotatable type 230V AC ISI marked complete all as specified and directed.

S&F Modular double USB charger 2 module 2400 mA confirming to IS 13252 (Part - 1) complete all as specified and directed

M & L for Point wiring with PVC unsheathed multi stranded copper conductor cable 1.5 sqmm (nominal dia ) 1100 volts in new PVC conduit 20 mm dia medium grade ISI marked and all conduiit accessories concealed in walls/ceiling/fixed to roof/truss/columns etc and new MS steel terminal boxes not less than 1.6 mm thick of required size (factory made) terminal boxes concealed in walls and with top cover of 3 mm thick hylam sheet of white colour including one run of 1.5 SQMM FRLS 1100 Volts copper conductor cable (green colour) as earth continuity connected to common earth for one light point complete all as specified and directed by Engr-in-Charge for the followings:- Note :- (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC conduit to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

(a) One light /Ceiling fan/exhaust fan/ bell point controlled by one switch.

(b) One light point controlled by two Nos two way switches

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(d) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on Ind board

M&L switch piano flush type 5 amp SP one way ISI marked.

S & F switch piano, flush type, single pole, TWO way, 5 Amps 230Volts ISI Marked complete all as specified and directed.

M&L socket outlet 5 Amps 5 pin flush type ISI marked

Supply & Fix fan regulator electronic step type 5 steps piano type, one module connecting complete all as directed.

S&F ceiling rose, PVC poly carbonate, isolated body with three terminals.

M&L bell electric (ding dong) 230 volt, SP all as specified and directed.

S & F sheet metal enclosure single pole and Neutral with a two pin earth plug top and socket complete with a MCB SP 20 Amp, "C" Curve 220 volts, 50 Hz, 20KA breaking capacity complete all as specified and directed.

Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20-22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC system efficency at luminair level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed by Engr-in-Charge. Note :- All the above mentioned specs will be verified though LM 79 nd LM 80 report NABIL accredited lab before supply LED fixtures.

Supply and fix LED batten luminaire surface mounted 2 feet system wattage of 9-10 watts and not less than 1000 lm with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed. Note : The above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures.

S&F decorative type wall mounted luminaire with unbreakable poly carbonate materials (comet type) with 1 x 14 watt LED bulb B22 base complete all as directed.

Supply and fix LED 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6000K, Surge protection of 4 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed. complete all as specified and directed. Note :- All the above mentioned specs will be verified though LM 79 nd LM 80 report NABIL accredited lab before supply LED fixtures.

Supply and fix surface ceiling mounted, round LED down light fitting 15 watts with die cast aluminium housing and system wattage of 15W, system efficacy at luminary level ≥ 100 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 3 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed. Note :- All the above mentioned specs will be verified though LM 79 nd LM 80 report NABIL accredited lab before supply LED fixtures.

M&L for angle Lamp holder with metalic ring, pvc/ polycarbonate type back plate with 09 watt LED Bulb suitable for B-22 base complete.

S&F 30W High efficient LED Street light fitting with pressure die cast Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie should more than 110 lm/W. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<10%, High and low protection along with a surge protection of 4 KV including provision of suitable dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed.

S & F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, having adjustable knob for temperature control and inner tank material of superior glass lined tank and outer body material of ABS with high pressure withstanding capacity (upto 8 bar pressure) complete all as specified of capacity 25 ltr having heating element 1.5 KW and not less than 5 star rating.

Supply and fix Instant Hot Water Geyser 3 Ltrs capacity,3 KW with corrosion proof thermoplastic external body ,withstand high pressure capcity to use in high rise buildings ISI approved with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection complete all as specified and directed

S&F ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5star rating energy saving, rated air delivery >220cum/min, AC single phase 230/240 V sixe 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length complete all as specified and directed. Note :- It shal work with existing electronic fan regualtor.

S&F wall mounted fan 400 MM sweep , areodynamic designed, air delivery >70 CMM, thermal over load protected mortar, 3 blade white colour, 230 volts, 50 HZ, 1420 RPM with 90 degree oscilation and having speed & oscillation control by two pull cords system complete all as specified and directed.

Supply and fixing Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body, air delivery > 800 CMH, 5 number of blades single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm complete all as specified and as directed.

Supply, and Fixing wall mounted angular Electric chimney black colour of suction power not less than 1220Cum/Hr,Al casette with stainless steel outer layer ,touch control panel,3 speed motor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 10 feet as per site required complete all as specified and as directed.Make: Elica model kitty Plus or equivalent in kaff/ Hindware

S&F MCB DB SPN 12 way Horizontal, IP - 43,IK 09 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as directed.

S&F MCB DB SPN 04 way, single door 240 V AC 50Hz ,MCB SPN as incomer / out going complete all as directed .

S&F MCB SPN 40 to 63 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

S&F MCB SPN 16 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

S&F MCB SP 6 - 32 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

M &L telephone Point wiring complete with single pin 0.61mm dia copper conductor cable telephone pain taped and rip conforming to ITD specification D-3003 and ITI-113C/114C cable PVC insulated drawn though PVC concealed conduit not less than 20 mm dia for one 2 pin telephone socket out let on independent modular type board complete all as specified and directed.

Supply & Fix in repair RJ-11 Telephone socket with transparent shutter 1 module on phenolic laminated sheet etc as required complete all as specified and as directed.

S&F PVC telephone Junction box suitable for 2 incomming and 2 outgoing connection complete.

M&L for Sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 4 Sq mm 02 Nos. (for Phase & Neutral) along with earth wire FRLS PVC insulated unsheathed stranded copper conductor wire of size 4 sq mm wire drawn through in & including PVC conduit 20 mm dia medium grade ISI marked including all fitting accessories fixed on wall/roofs/ceilings etc complete all as directed. Note:- (i) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (ii) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

M&L for Sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 6 Sq mm 02 Nos. (for Phase & Neutral) along with earth wire FRLS PVC insulated unsheathed stranded copper conductor wire of size 6 sq mm wire drawn through in & including PVC conduit 20 mm dia medium grade ISI marked including all fitting accessories fixed on wall/roofs/ceilings etc complete all as directed. Note:- (i) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (ii) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

M&L for Sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 10 Sq mm 02 Nos. (for Phase & Neutral) along with earth wire FRLS PVC insulated unsheathed stranded copper conductor wire of size 10 sq mm wire drawn through in & including PVC conduit 25 mm dia medium grade ISI marked including all fitting accessories fixed on wall/roofs/ceilings etc complete all as directed. Note:- (i) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (ii) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

M&L earthing complete with GI electrode 600x 600 x 6mm, thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level (with top edge of earth plate not less than 1.50 mtr below normal ground level connected to GI strip 25x4mm as earthing lead by means of bolt nuts, check nuts, and washers of brass connected including gun metal or phosphorus bronze of size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of GI strip incl laying of alternate layer of charcoal dust and common salt PPC (1:2:3) type C-1 (using 20mm graded stone aggregate) for earth pit with 40 x 40 x 6mm MS angle iron frame for cover 40 mm thick (1:2:4) type B20 using 12.5 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally PGL funnel with ground wire mesh 20mm dia GI pipe Medium grade for watering complete all as shown on electrical plate No 3 of SSR Part-1 2009 and connected in earth test incl testing completed all as specified and directed. Note:- Galvanised strip and protection light grade GI pipe upto 7.5 mtr shall be deemed to be in the rates.Galvanised strip shall be fixed on wall with suitable size of porcelain / PVC insulator.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 25x4 mm thick galvanised strip with duly fixed on suitable size of porcelain/PVC insulator complete all as specified and directed.

M&L for fixing of GI tubing medium grade 40 mm dia fixed to wall / ceiling for hanging of ceiling fan (Approx length- 2.4 RM) including suitable size of fan hook as per site requirement and cement work including making good the disturbed surface with existing surface complete all as specified and directed.

Supply and lay in repairs XLPE insulated PVC bedded galvanised steel strip or wire armoured electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 06 Sqmm 2 core including connection of cable at both ends with suitable size of glands, aluminum lugs complete jointing, testing and commissioning complete all as specified and directed.

Excavation, in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr in depth for laying under ground cable in hard / dense soil and getting out complete all as specified & directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc. 25 cm complete all as specified and directed.

Removal of excavation material not exc 50 Meter and depositing where directed at a level not exc. 1.5 M above the starting point complete all as specified and directed.

Supplying laying sub class ‘B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection complete all as specified and directed.

M&L for dry river sand filling in trenches as cushioning to under ground cable provided with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying complete all as specified and as directed by EIC. Note :- Punned thickness only shall be measured and paid.

Supplied & fixing GI tubing medium grade 40 mm dia with required fittings laid along with poles/walls/Roads/Paths for incoming and outgoing of cable complete all as specified and directed of following

ASSOCIATED CONSTRUCTION CO.

M/S ANIL KUMAR

imran construction company

VED PRAKASH ARORA

tarun construction co

M/s Puja Construction Company

ASSOCIATED CONSTRUCTION CO.

imran construction company

tarun construction co

VED PRAKASH ARORA