RENOVATION OF GROUND FLOOR OLD BUILDING AT ADA CAMPUS 2

Electrical Items :

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead of thickness above 25 mm up to 40 mm. All dismantled materials should be taken away from the site.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead for existing tiles. All dismantled materials should be taken away from the site.

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m for All kinds of soil

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level of 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level of Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge of Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Glass reinforced Gypsum ( GRG) plaster board 12.5 mm thick confirming to IS 2095 (Part 3):1996

Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and Lsections suitably fixed according to tile size as per direction of Engineer-in-charge.

Distempering with 1st quality acrylic distemper (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade of Old work (one or more coats).

Finishing walls with water proofing cement paint of required shade of Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Specialized technicians and Helper (Technician) for removing the existing broken glasses and shifting the glasses to the location as decided by ADA department.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick of Float glass panes of 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up with approved block laying polymer modified adhesive mortar all complete as per ADA instructions.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

12 mm cement plaster of mix for Internal plastering with 1:4 (1 cement: 4 fine sand)etc complete as per ADA instructions.

Providing & fixing of 600 x 600 mm approved make,shade and size for dadooing with 20mm thick cement mortar 1:3 mix,lush pointing with white cement using colour pigment,including cost of materials,labour,back plastering curing etc complete as per sample available at ADA and OEMs specification.

Providing, fabrication and installation of Vista or Fenesta or Hunter Douglus make Manual operated Window Blinds, approved shade fabric including accessories, all as per OEM specification, etc complete as per ADA instructions.

Specialized technicians and Helper (Technician) for cleaning of glass including removal of sun film etc complete as per ADA instructions.

Providing & rendering re-polishing of existing doors, double coat to get neat and even finish using spray machine similar to existing matt finish surface including surface preparation etc. complete, all as per OEMs specification. (MRFPUF coating).

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of existing size and including all necessary fittings etc complete as per ADA instructions.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade of One or more coats on old work.

Charges towards removing of Existing work station fabric panel Upolstry and fixing with new fabric Upolstry. Cost with including transportation labour charges tools & machines etc., complete as per sample available at ADA.

Supply, and laying of Main Circuit, 2 runs of 4 sq mm+ 1 run of 2.5 sq mm flexible PVC insulated copper wire should be run in 1” casing N capping / PVC conduit pipe with connected accessories complete in all respect(For Power Point).

Supply, and laying of Sub Circuit, 2 runs of 2.5 sq mm+ 1 run of 1.5 sq mm flexible PVC insulated copper wire should be run in 1” casing N capping / PVC conduit pipe with connected accessories complete in all respect(For Power Point).

Supply and installation of 01 No. Of 5/15A power socket out let controlled by 20A single pole switch with indicator housed in single pole switch with indicator housed in PVC boxes, fixed at sitting desk as required by client.(8 modular switch plate with box, white colour, for RAW power points including internal wiring).

Supply and installation of 03 No. Of 5/15A power socket out let controlled by 20A single pole switch with indicator housed in single pole switch with indicator housed in PVC boxes, fixed at sitting desk as required by client.(8 modular switch plate with box, white colour, for UPS power points including internal wiring).

Supply and fixing of 2x2 feet 36W square LED fitting of false ceiling type and including necessary point wiring with switch control board accessories.

Supply and fixing of 2x2 feet 36W square LED fitting of false ceiling type and including necessary accessories.

Supply and fixing of 4 feet 20W LED tube and including necessary accessories.

Supply and installing following size of perforated Hot dipped Galvanized Iron cable tray (Galvanization thickness not less than 50 microns) with pergoration not more than 17.5% inconvenient sections, joined with connections, suspended from the ceiling with GI suspenders including GI bolts and nuts etc as required (300mm width X 50mm depth X 1.6mm thickness)

Supply, Installation, Commissioning and Testing of 2TR Capacity Cassette type Air Conditioning System complete with accessories like indoor unit, outdoor unit, cordless remote control and vidoflex insulation foam etc. including pressure testing, topping up of R410/407C gas, providing MS angle frame for mounting outdoor units (outdoor unit stand), Installation of Ac by inter connecting the suction & discharge pipe, laying the drainage pipe fixing the indoor unit & fixing the outdoor unit on the frame with necessary support & clamp, testing and commissioning units. Detailed specification of 2TR Cassette Type • Nominal cooling capacity • Power supply • Fan Type • Condensate drainage • Air Filter • Air Flow Volume • Noise Level •6000 Kcal/hr = 24000 Btu/hr •220-230 volts, 1phase, 50Hz •3Dimension Screw Fan 12000m3/hr •Built in water pump •Woven high density polyethylene •Four way Air flow -1200 m3/hr •44 db(A)

Supply of Suction & Discharge pipe Size 5/8” Copper for Suction & 3/8”for discharge to inter connect indoor & outdoor with necessary vidoflex insulation.

Supply and fixing of 1” dia PVC pipe including necessary fixing accessories for Drain pipe line.

Supply and Laying of 2.5 sq mm 6 Core PVC Flexible copper cable through PVC pipe to individual A/c indoor unit to outdoor unit including necessary fixing accessories.

Supply & Wiring 2 x 2.5 Sq mm wire in conduits or wire race ways. Supply & Wiring 1 x 1.5 Sq mm wire in conduits or wire race ways. (RAW Power DB to industrial plug top)

Supply and fixing of 4” PVC (Box Type) casing & capping for routing copper piping and drain piping. (Wherever required)

Supply and fixing of MCB 2 Pole: 20 Amp along with industrial socket plug & box charges including necessary termination of wires, testing and commissioning of the circuit.

Supply, Installation, Commissioning and Testing of 2TR wall mounting Split Air Conditioning System complete with accessories like indoor unit, outdoor unit, cordeless remote control and vidoflex insulation foam etc. charges including pressure testing, topping up of gas, providing MS angle frame for mounting outdoor units (outdoor unit stand), installation of Ac by inter connecting the suction and discharge pipe, laying the drainage pipe. Detailed specification of 2TR Cassette Type • Nominal cooling capacity • Power supply • Fan Type • Air Filter • Air Flow Volume •6000 Kcal/hr = 24000 Btu/hr •230 volts, 1phase, 50Hz •2Dimension Screw Fan12000 m3/hr •Woven high density polyethylene •Two way Air flow -1200 m3/hr

Supply of Suction & Discharge pipe Size 1/2” Copper for Suction & 1/4”for discharge to inter connect indoor & outdoor with necessary vidoflex insulation.

Supply and fixing of 1” dia PVC pipe including necessary fixing accessories for Drain pipe line.

Supply and Laying of 2.5 sq mm 4 Core PVC Flexible copper cable through PVC pipe to individual A/c indoor unit to outdoor unit including necessary fixing accessories.

Supply & Wiring 2 x 2.5 Sq mm wire in existing conduits or wire race ways. Supply & Wiring 1 x 1.5 Sq mm wire in existing conduits or wire race ways. (RAW Power DB to industrial plug top)

Supply and fixing of 4” PVC (Box Type) casing & capping for routing copper piping and drain piping. (Wherever required)

Supply and fixing of MCB 2 Pole: 20 Amps along with industrial socket plug & box charges including necessary termination of wires, testing and commissioning of circuit.

Supply and fixing of MCB Single Pole: 20 Amps (Existing Raw power DB)

Dismantling of Existing GI A/c duct of size 2feetX2feet to be removed and handed over to Electrical department (Approximate 30 RMT)

TThe premium executive table size shall be : 2400 Width mm x 1104 Depth mm x 735 Height mm. The top panel shall be 40 mm thick(18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster. The understructure shall be having legs made from 1.6 mm thick MS clad with the strips of MFC (Medium Density fiber). Hollow construction of legs facilitates wire management. The modesty & side panel should be 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer. Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). The Premium executive table ERU size shall be : 1400 Width mm x 580 Depth mm x 690 Height mm. The top panel shall be 40 mm thick (18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster. The understructure shall be having the modesty panel of 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer . Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). The Back unit size shall be of : 1860 Length mm x 580 Depth mm x 670 Height mm and the tower case of 1700mm Lengthx40mm Depthx1200mm Height. The door shall be 23 mm thick ( 18 mm thick Batons + 4 mm Veneer + 1 mm Backing Decorated ( BDL) ) . The Shelves and Partitions should be of 18 mm thick MDF( Medium density fiber) + Pigmented Black and coated with Melamine.

• Supply& installation Mid Back revolving chair without Tilting Mechanism. • The seat should be made up of 1.2 ± 0.1cm. Thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. • Back size:53.0cm.(w) x 73.0cm.(h) seat size:54.6cm.(w) x 49.0cm.(d) thehr polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkhrsteel and should be black powder-coated ( dft 40-60 microns ) the armrest assy. should comprise of three parts viz. the armrest support tube and p.u. armrest and the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm m.s.e.r.w. support tubes and chrome plated. The p.u. armrest should be made of black integral skin polyurethane with 50-70 shore hardness and reinforced with m.s. insert. The armrest top should be made of abs & upholstered with foam & leather the seat base assy. should be designed with following features: 360° revolving type without back tilt. It has an adjustment stroke of 12.0 ± 0.3cm the bellow should be 3 piece telescopic types and injection moulded in black polypropylene the pedestal should be made of die-cast aluminum with buffing finish. it should be fitted with 5nos. twin wheel castor. the pedestal should be 67.0 ± 0.5cm pitch-centre dia. (77.0 ± 1.0cm with castors) the twin wheel castors should be injection moulded in black nylon. • Overall Dimensions of Chair: Seat Height - min 43.4 to max 55.4 cm.Back Height - min 99.4 to 111.4 cm

• SEAT FOAM: The seat is made up of PU foam in Density 28 ±2 kg/cum with an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. • BACK FOAM: The back is made up of PU foam in Density 28 ± 2 kg/cum with two additional top layer of super soft foam of density 32±2 kg/cum, upholstered with fabric or leatherette. • UNDERSTRUCTRE: Under structure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS: 303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over under structure for cushioning purpose. • LEG ASSEMBLY: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic end cap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45CM.

Supply & installation of Centre Coffee table with glass top, wooden legs 100 x 65 x 45 mm. • Overall Size : Width : 100cm Depth : 65cm Height : 45cm TABLE LEGS METERIALS: Colour :cherry • TABLE TOP MATERIALS & SIZE: (tempered Glass/ 10mm), L X W X T: 1000x650x10mm Colour: clear.

Supply & Installation of Discussion table of 1100 mm Pod with height of 750mm with Material leg is made up of epoxy coated mild steel and material of table top is 25mm and it is made up of melamine faced particle board.

Supply of ‘L’ shaped Manager Table of size shall be 1650mm(L) x 750mm(D) and Return Table 1200mm(L) x 450mm(D) with one side attached Frame of Fabric Magnetic and White board. Work top shall be made up of 25mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2mm thick PVC Edge band with glue of standard quality.The single side legs shall be used for supporting panels & work surface on one side only. Single side legs shall be fabricated by CO2 welding in MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm and this shall be coated with minimum 45 micron thickness of epoxy powder coating. Body Panel Structure: uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 or equivalent and shall have an average wall thickness of 1.2 mm and also powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall be comprises of L- Channels and it shall be made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. The 52.4 mm panel has more elaborate and flexible construction offering various functional and decorative finishes as well as cable management capacity.

Supply and Installation of Desking -Premium suite model of size 2350*2350*750mm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestals are provided with lock for security. The Back unit size shall be of : 2350 Length mm x 50 Depth mm x 1800 Height mm. made of 25mm thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2mm thick PVC clipping. Grommet cut out provided at the top of the work surface for wire management. Handles are provided for ease of opening. Storage is provided with cam lock for security.

Supply and installation Desking -Premium suite of size 165*195*75 cm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Supply & Installation of Desking -Premium suite of size 180*210*75 cm (Main Table +ELU+PED). Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing & fixing of modular customized Rectangular work station of size 1200mm (L) x 600mm (W) x 1200mm (H) each, The table top made out of 25mm thick Pre-laminated particle board with PVC edge, the under structure made out of 25mm thick Pre-laminated particle board, Cable manager to be provided on the work surface and accessed through grommet cut out on the worktop, incl vertical movements of wires. Partition should be 75 mm thick , made out of PLB either sides , one number white board per person rest fabric magnetic, all bottom tile metal powder coated, partition height 1.20 m height with cable race ways at two level for drawing power / data / voice cable, height adjustable fixtures as per existing arrangement / shade. Stability of the structure individually and totally will be the responsibility of the vendor. All as per OEMs specification, Drawing 'A' sample available at ADA.

Overall Dimensions of Chair-Seat Height - min 49.9 to max 58.9 cm. Total Height - min 134.9 to 143.9 cm. Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm • Seat/back assembly: The seat should be made up of 1.2 ± 0.1cm. Thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. back size: 53.0cm.(w) x 95.4cm.(h) seat size:54.6cm.(w) x 49.0cm.(d) the hr polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression the seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkhrsteel and should be black powder-coated (dft 40-60 microns ) • Armrest assay: the armrest assy. should comprise of three parts viz. the armrest support tube and p.u. armrest and the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm m.s.e.r.w. support tubes and chrome plated. The p.u. armrest should be made of black integral skin polyurethane with 50-70 shore hardness and reinforced with m.s. insert. the armrest top should be made of abs & upholstered with foam & leather the mechanism should be designed with the following features: * 360° revolving type * seat back tilting ratio of 1 : 1.5 * Front pivot for tilt with feet resting on ground ensuring more comfort. * tilt tension adjustment. * 5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock should be released * Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking. it has an adjustment stroke of 9.0 ± 0.3cm the bellow should be 1 piece and blow moulded in black polypropylene the pedestal should be made of die-cast aluminum with buffing finish. it should be fitted with 5nos. twin wheel castor. the pedestal should be 67.0 ± 0.5cm pitch-centre dia. (77.0 ± 1.0cm with castors) the twin wheel castors should be injection moulded in black nylon.

• Supply & Installation of MID BACK CHAIR, the seat Material- Leather, Color – Black, Revolving Chair – Yes, SEAT/BACK ASSEMBLY: The seat is made up of 1.2 +0 1cm thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam The back is made up 1.2 TO 1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam The back ply and foam is designed with contoured lumber support for comfortable seating posture * MID BACK SIZE 48.5 cm (W) X 64.5 cm (H) * SEAT SIZE 51.0 cm (W) X 48.0 cm (D) • HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back is moulded with density = 45 +/-2 kg/m* and Hardness load 16 2 kgf as per IS 7888 for 25% compression • ARMRESTS (ADJUSTABLE):The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of B3 81z0 03 cm x 0 2-LO 01 cm thk M S E R W tube having chrome plated finish The armrest height adjustable up to 6 5z0 Scm in 5 steps • KNEE TILT SYNCHRO MECHANISM WITH SEAT DEPTH ADJUSTMENT * 360° revolving type Single point control * Single point control * Front pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment * 4-position locking with anti-shock feature Seat back tilting ratio of 1.2 * Seat depth adjustment of 6.0 +0 Scm can be locked in 6 positions • FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features * 360° revolving type Single point control * Front pivot for tilt with feet resting on ground ensuring more comfort Tilt tension adjustment * 4-position locking with anti-shock feature * knockdown condition vacations within +1 0 cm • ADJUSTABLE BACKREST: The back rest is connected to the mechanism with a drop-iift mechanism which can be adjusted in the range of 7.0 IO.5cm. And locked in 5 positions for the better lumbar support. • FIXED SPINE (COFERENCE/ VISITOR): The seat and back are arrested together with fixed type spine i.e no back up/down adjustment; made of 0.8 TO.05 cm thk HR Steel and is black powder-coated ( DFT 40-60 microns ) • HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.010.3 cm. • PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 0.02 cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.010.Scm. Pitch-centre dia. (76.011.0 cm with castors). • TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.

Supply & installation of High Back Pure leather revolving chair of size approximately 76.10L x 76.10D x 114-131.50H CM and seat height 44.50-54.50cm. The chair made by Leather high back chair, Back profile can be adjustable, Active Bio-synchro Mechanism. The chair comes with 5 position tilt limiter.

Supply & installation of Mid Back Pure leather revolving chairs for visitors size approximately 76.10L x 76.10D x 96.50-114H CM and seat height 44.50-54.50cm. The chair made by Leather high back chair, Back profile can be adjustable, Active Bio-synchro Mechanism. The chair comes with 5 position tilt limiter.

Supply of MID BACK CHAIR of Overall Dimensions shall be Chair-Seat Height - min 43.3cm to max 54.3cm. Height - min 89.5cm to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3cm and Depth- 76.3cm.Seat assembly: The seat assembly shall be made up of 1.2 ±0.1cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. Seat size: 47.0 cm. (w) x 48.0 cm. (d) Back assembly: The backasembly. shall be made of powder coated (oft 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2±0.016cm.thick. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using double layer spacer mesh fabric with high tenacity yarn. Back size : 46.5 cm (w) x 60.5 cm (h).High Resilience (HR) polyurethane foam: The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.Armrests: The one-piece armrests shall be injection moulded from black co-polymer polypropylene. Centre-Tilt mechanism: The mechanism shall be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • upright position locking. tilt tension adjustment. Pneumatic height adjustment: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.Telescopic bellow assy: The bellow shall be 3 piece telescopic type and injection moulded in black polypropylene.Pedestal assembly: The pedestal shall be injection moulded in black 33% glass-filled nylon66 and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm. Pitch-center dia. (76.3 ±1.0cm with castors.)Twin wheel castors: The twin wheel castors shall be injection moulded in black nylon etc.

Supply of Mid Back Chair of size shall be : SEAT SIZE (Larger Seat Depth) : 47.00cm (W) x 51.50cm (D), SEAT SIZE (Standard Seat Depth) 47.00cm. (W) x 49.50cm.(D), BACK SIZE : 45.00 cm(W) x 65.3cm(H).The seat shall be made up of 1.2 + 0.1cm thick hot pressed plywood. The Back shall be made up of injection moulded glass filled nylon & upholstered using Mesh fabric with high tenacity yarn. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam shall be moulded with density 45+/-2 kg/cum and hardness 16 + 2 kgf as per IS:7888 for 25% compression.ARMRESTS : The adjustable armrest shall be designed with the following features:Up-Down adjustment— 8 steps (8 0+0.Scm range).Height adjustable armrest structure which shall be powder coated & fitted with an armrest top.Fixed Armrest Top shall be PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side. Lumbar pad shall be an adjustment of 8.0 + 0.5 cm in height.

SEAT/BACK ASSEMBLY: The seat is made up of 1.2 * 0 fern thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 The Back is made up of injection moulded glass filled nylon & upholstered using Micro mesh fabric with high tenacity yarn with 28 density foam Sandwich in lumbar area. * SEAT SIZE(Larger Seat Depth) : 47.0 cm. (W) x 51.5 cm (D) * SEAT SIZE(Standard Seat Depth) 47 0 cm. (W) x 49.5 cm. (D) ” BACK SIZE : 45.0 cm. ”(W) x 65.3 cm. (M) HIGH RESILIENCE (HR) POLYURETHANE FOAM The HR poly methane seat foam is moulded with density 45+/-2 kg/m"" and hardness 16 + 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the folIowing features » Up-Down adjustment— 8 steps (8.0+0.Scm range) • Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad Lumbar pad has an adjustment of 8 0 + 0.5 cm in height.FRONT PIVOT SY!’JCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features.

Supply & installation of High Back Pure leather revolving chair of size approximately 75L x 75D x 102-119H CM and seat height 45-55cm. The chair made by Leatherette high back chair, Back profile can be adjustable, knee tilt synchro Mechanism. The chair comes with 3 position tilt limiter.

Providing, fabrication and Installation of Conference Table - 8500L x 1500 D x 750 H Table. Cable Tray & Vertical Cable riser will be provided. 25mm Thick Prelaminated Board Table top with 2mm Thick PVC Tape Edge Banding. Table will have 3 Nos Flip Cover and Electrical Cutout provisioning Cable Tray. Charges included transport and shifting etc complete as per OEM specifications and directed by engineer-in-charge. The design of the table is confirmed by the ADA.

Providing and fixing of 3 Drawer Mobile pedestal of size 314(l) x 400(w) x 80(h) and 22.5(h) all as per OEM Specification and sample available at ADA.

Sliding computer key board tray of minimum size 473mm (L) X 200mm (D) metal tray is made of minimum 0.8 mm thick CRCA D grade as per IS-513 with sliding channels and other fixing fittings. The front face of tray shall match work surface edge. It should also have a Single extension ball slide assembly/Telescopic slider assembly, retro fit mouse tray.

230-345W X 226D X 180H CPU Trolley is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet Lockable/Non-lockable twin wheel castors are injection moulded in Black Nylon.

Orkay Interior & Modular Pvt Ltd

PNR INTERIOR SOLUTIONS PVT LTD