Rajbhavan Colony sthit Awas No.-27 Type-5 me lawn ki shatigrast farsh ke sthan par Endura tiles lagane ka karya avem awas ke purane va kamzor darwaze badalne ka karya avem ek UPVC khidki lagane ka karya anya civil sambandhi karya.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below DAR NO-15.13.1

Providing wood work in frame of door , window , clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fastener of requried dia & length (hold fast lugs or dash shalle be paid for separately).(dar-9.1.1)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 30 mm thick dar no-9.9.1.2

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood 30 mm thick dar no- 9.27.2.1

Provding and fixing ISI marked flush door shutters conforming to IS : 2202 (part-1) non- decorative type, core of block board contruction with frame of 1st class hard wood and well matched commercial 3 ply veneers on both faces of shutter :30mm thick including isi marked stainless steelbutt hinges with necessary --9.21.2

Providing and fixing of mica on door including cost of with necessary screws, excluding panelling which will be paid for separately. All complete as per direction of engineer in charge

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) DSR NO 13.116

Providing and layeing in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level:1:5:10 (1 cement :5 coasre sand ( Zone-III) :10 graded stone aggregate 40 mm nominal size dar-4.1.10

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in-Charge.In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement: 4 coarse sand)Acid and alkali resistant tile DSR NO-11.21.2.1