CA NO CWE BTD 59 of 2020-21 SPECIAL REPAIRS TO BLDG NO P-457, OFFICE COMPLEX, OR LIVING AND STORE OF HQ INF BDE AND BLDG NO P-7 OR LIVING ACCN OF EME WKSP (SIG GP) UNDER GE (SOUTH) BATHINDA AT BATHINDA MIL STN

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each and removing from site including cutting holes for removal of hold fast complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each and removing from site including cutting holes for removal of hold fast complete.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and re-fixing in the same opening including easing and adjusting including renewal of unserviceable screws etc complete.

Taking down shutters of any description not exceeding 1 Sqm each and re-fixing in the same opening including easing and adjusting including renewal of unserviceable screws etc complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 125 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

All as per item No. 6 above but frame size 105 x 60 mm

All as per item No. 6 above but frame size 75 x 60 mm

S & F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S&F in repairs FRP door frame of size 100mm x 60 mm with inner core of treated and seasoned rubber wood and outer core of average 2mm thick FRP with gel coat finish and with average weight of 4 Kg per RM all as directed.

S&F FRP door shutter 30mm thick are to be made with 3mm FRP unsaturated polyester resin moulded to 3mm FRP laminate for forming hollow rails and styles suitably rebated and seasoned rubber wood are to be filled inside at required places for fixing of fitting cast monolithically with 5mm thick FRP laminate for panels with gel coat finish and with average weight of 8 Kg per Sqm all as per IS-14856-2000.

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate in filling in chowkats/ door frame or bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

S&F in repairs, stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including one shop coat painting all as directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat painting including dismantling of old existing window as directed.

S & F MS framed work such as grills, gratings, guard bars etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Gde E-165.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips size not exceeding 1.5 Sqm each pane complete.

S & F sheet glass, 3 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary complete.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

All as per item No 22 above but fixed in repairs.

S & F MS framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, not exceeding 10 Kg each brackets, conforming to Fe 290 Gde E-165.

Cutting holes in exceeding half brick but not exceeding one brick walls built in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B1 as required at site.

S & F butt hinges, medium weight, cold rolled mild steel and fixed, size of hinges 100mm.

S & F 200 mm long aluminium anodised, barrel tower bolts of extruded section.

S & F 150 mm long aluminium anodised, barrel tower bolts of extruded section.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type), and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, length of bolt 250mm.

S & F 125 mm extruded aluminium alloy handles, fabricated type, anodised.

S & F 125 mm aluminium handles, cast type, anodised.

S&F 100 mm size Hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws

S&F in repairs mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm.

S&F butt hinges, extruded aluminium alloy with with galvanised mild steel hinge pin, anodised and fixed, type B-21, size of hinge100mm.

S&F in repairs mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 250 mm.

S & F in repairs 125 mm mild steel pressed handles, oval type, stove enamelled black.

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300 mm.

S&F mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm.

S & F 150 mm mild steel pressed handles, oval type, stove enamelled black.

S & F floor door stopper of aluminium alloy body, and tongue, ISI marked, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm.

S&F aluminium powder coated ventilator including necessary rubber gasket for fixing glass panes etc complete all as shown on drawing No CEBT/SK-936 sheet No.1/1. (Note- Glass panes and wire mesh shall be measured and paid for separately).

S&F factory made anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F factory made anodised aluminium door shutters, aluminium sections weighing not less than 0.55 kg/metre including necessary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc complete all as specified.

S&F factory made anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 nos.) suitable handle (1 no.) complete all as specified.

S & F door closer hydraulically regulated, designation No 3, universal type, aluminium (extruded section) body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.

S & F sheet glass, 5.5 mm thick palin/tinted (colour) in square exceeding 0.5 Sqm in each pane.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M & L for painting to old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of old painted surfaces.

M & L for painting to old wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of old painted surfaces.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint.

S&F factory made PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame all as per specifications and drawings in SSR Part -II (2104) (PVC fillets and PVC strips shall be measured and paid separately) including dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame all as per specifications and drawings in SSR Part -II (2010).

S&F 5mm thick PVC plain colour sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of solvent Cement and fixining at site.

Providing and fixing of E-board 600x600x4mm thick white prelaminated sheet embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.30mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 2mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction and finishing the surface by applying two coat of plastic emulsion paint including M&L for dismantling existing boarding of any description fixed in any position with nails including fillets.

S&F 25mm dia stainless steel drapery rod alongwith brackets and decorative end pipe feneal complete all as specified. Note:- Brackets and decorative end pipe feneal shall be measured and paid as supllied only separterly.

Supply only wall to wall stainless steel brackets

Supply only stainless steel brackets

Supply only decorative end pipe feneal

Taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement mixed with liquid water proofing material as per manufacturer's instruction complete all as specified. (Liquid water proofing material shall be measured and paid for separately.)

M&L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling complete all as specified.

M & L for preparation of newly plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of 100% acrylic emulsion paint by using airless spray/ roller over and including a coat of acylic internal primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

Complete removal of existing treatment on wall (any number of layers) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of 100% acrylic emulsion paint by using airless spray/ roller over and including a coat of acylic internal primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparation of newly plastered surfaces of external walls and apply two coats of Cement base paint over a coat of alkali resistant primer all as specified.

Complete removal of existing treatment of wall (any number of layers) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered surfaces of walls and applying two coats of cement base paint of approved tint over and including a coat of alkali resistance external primer.

M&L for preparation of newly plastered or unplastered surface and applying three coats of white wash on ceilings.

M&L for two coats of white wash including preparation of old surfaces of ceiling.

M&L for preparation of old treated surfaces of external walls by complete removal of existing treatment by scrapping wall and applying anti fungal treatment including washing down with water and application fo Bio wash antifungalisation and CW primer and applying two coats of anti fungl paint over one coat of primer of Make Apex from Asian Paint/ Excel from Nerolac / Weather coat from Berger.

M & L for preparing newly plastered surfaces of walls and applying three coats of white wash all as specified.

M&L for two coats of white wash including preparation of old surfaces of walls.

M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe.

S&F in repairs vitreous china wash down water closet pan (EWC) (single piece), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc and including flushing cistern and white coloured plastic seat cover and mild steel chromium plated or aluminised hinging device complete.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia 900 mm long complete.

M & L for 15 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 15 mm bore existing steel tubing and connections complete.

M & L for 20 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20 mm bore existing steel tubing and connections complete.

M & L for 25 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 25 mm bore existing steel tubing and connections complete.

M & L for 40 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F in repairs brass CP fancy type mixer for mixing hot and cold water screwed for iron pipe of 15 mm bore.

S&F in repair supply only 15mm bore chromium plated, fancy type, quarter turn Pillar cock screwed down high pressure, with or without lettered Hot ot Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified.

S&F in repairs stop valves, chromium plated, fancy type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S&F stop valves, cast copper alloy, fancy type, quarter turn, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S&F in repairs, 15 mm bore chromium plated, long shank fancy type, quarter turn, bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F in repairs stop valves, chromium plated, fancy type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe.

S&F in repairs stop valves, chromium plated, angular type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S & F in repairs, PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts.

S & F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints fix to steel pipe or union complete all as specified and as directed.

S&F in repairs, brass chromium plated tubular towel rail, 20 mm dia, D type, 600 mm long between flanges fixed with CP screws and wooden cleats.

S & F in repairs, stainless steel chromium plated soap tray of size 100 x 100 x 60mm and fixed on wall with chromium plated brass screws complete.

S & F grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gm).

S&F in repairs toilet paper holder, coloured, vitreous china, box type fixed to walls with chromium plated brass screws.

S & F in repairs vitreous china wash hand basin, white, of size 550mm x 400mm , excluding waste, chain and plug and porcelain stopper but including 32 mm dia waste coupling fancy type chromium plated, and PVC waste pipe of 32 mm dia and fixed all as directed complete .

S & F in repairs vitreous china wash hand basin, coloured, of size 450mm x 300mm , counter type, oval shaped, excluding waste, chain and plug and porcelain stopper but including 32 mm dia waste coupling fancy type chromium plated, and GI waste pipe of 40 mm dia and fixed all as directed complete, .

Taking down carefully and re-fixing of wash hand basin of any size, vitreous china and replacement with new bracket, 32 mm dia waste coupling fancy type chromium plated, and PVC waste pipe of 32 mm dia and fixed all as directed complete .

S&F brass chromium plated bottle traps of suitable size for wash hand basin with inlet and outlet screwed for iron pipes or connection including necessary packing, union and cap fixed.

S&F in repairs vitreous china urinal, half stall type, white, including and providing and fixing plugs, bedding urinal against wall in CM (1:2) securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, S&F automatic flushing cistern with brackets and spreader, flush pipe, grating and union for discharge pipe complete.

Taking down carefully and re-fixing of vitreous china urinal, half stall type, including and providing and fixing plugs, bedding urinal against wall in CM (1:2) securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, S&F automatic flushing cistern with brackets and spreader, flush pipe, grating and union for discharge pipe complete.

Dismantling of 100mm /75mm / internal dia cast iron or reinforced concrete PVC drain pipes, jointed in cement mortar and taking out of trenches, fixed to wall including all fittings.d.

S & F 75 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps / laid in trenches

S & F 100 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps / laid in trenches.

S&F in repairs 75 mm dia stainless steel floor trap with grating incluing jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door.

S & F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door.

S & F in repairs 100 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

S & F in repairs 75 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

M & L for salt glazed stoneware drain pipes, grade 'A', laid in trenches and jointed complete for 150mm internal dia of pipe including dismantling of existing drain pipes of any type and size, jointed in cement mortar all as directed.

M & L for 150 mm x 150 mm salt glazed stoneware gully traps, square or round moulded, type 'P'.

S & F 100mm dia cast iron bends (any radius) with duck's foot or heel rest.

Extra for joints over cast iron pipe of 100/75 mm bore pipes, bend joints etc provided Epoxy joints in lieu of cement joints complete.

S&F in repairs 100 mm cast iron Cowls.

S&F PVC (SWR) 110mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, fixed to walls including taking down old pipes and fittings.

Refixing only PVC (SWR) 110mm bore pipes fixed to walls including taking down old pipes and fittings.

S&F PVC (SWR) 110mm bore bends of any radius.

S&F 1000 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

All as per item No 117 above but capacity of tank 500 litres.

Demolition of PCC in ground floors and pavings not exc 15cm thickness (below or above ground level).

M & L for 25 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floors, path, pavings etc. finishing the surface even and fair.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish to a distance exceeding 1 km but not exceeding 2 km.

M & L for non skid coloured ceramic tiles of size minimum 400mm x 400mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) complete all as specified. Note: Only course sand shall be used in screed bed.

M&L for non skid coloured ceramic tiles of size 600mm x 600mm, 8 to 9 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified. Note: Only course sand shall be used in screed bed.

All as per srl item 123 here-in-before but in vertical sufaces as skirting including backing plaster.

S&F glazed ceramic coloured tiles 450 x 350mm, 7 to 8mm thick in verticle surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile.

M & L for machine cut kota stone slab flooring with size of kota stone as directed, 18 to 20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 20 mm thick Screed bed or bedding layer in CM (1:6).

All as per item No 126 above but in vertical surfaces such as steps , riser , skirting, dado and pillars as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4).

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for marble work (udaipur green) 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and roundening to the edge of stone slabs on edges including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6).

M&L for granite (of any type) work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, dado/skirting and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6).

M & L for vitrified ceramic tiles, 9 to 10 mm thick (square / rectangular), ultracharged, poished, light shade, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. (Screed bed shall be measured and paid for separately) including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6).

All as per item No 131 above but in vertical surfaces such as steps , riser , skirting, dado and pillars as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4).

Dismantling bricks laid dry flat or on edge and pointed in any mortar.

Welding in repairs n.exc 2.5 cm in length for thickness of metal to welded n.exc 6mm.

S & F in repairs chromium plated grating 125 mm size.

S&F 100mm cast iron sanitary connection socket to fit WC out-let.

Dismantling boarding of any type and description fixed in any position with rails including fillets complete.

M & L for prelaminated particle board, 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, ISI marked, fixed with screws to timber frame work complete including dismantling boarding of any type and description fixed in any position with rails including fillets complete.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised of 30 mm width of flap (when open).

M & L for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exceeding 6 Sqcm and not exceeding 13 Sqcm.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 210 gram).

S & F in repairs Gun metal globe or Gate valve , with iron wheel , screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe.

S&F stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 40 mm bore dia of pipe.

Water proffing treatment to sunken slab and adjoining vertical surfaces as specified under:- (a) M&L Rendring 10MM thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compount as per manufacturer instruction trowel even and smooth with steel trowel on sunken surfaces. (b) Applying first coat of chemical pidifin 2K (DR Fixit) on clered RCC Surfaces @ 0.86 KG/SQM (Minimum) as Recommended by Manufacturer. (c) Provide a layer of Glass fibre mesh of size 2.25MM X 2.25 (45GSM) over first coat of chemical pidifin 2K as per manufacturer Recommendation. (d) Applying second coat of chemical pidifin 2KB(DR Fixit) @ 0.86 KG/SQM (Minimum) over layer of glass fibre mesh of size 2.25MM x 2.25MM (45 GSM) as recommended by manufacturers.

Supply only liquid water proofing material, ISI marked.

M&L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling of sunken floor including demolition of existing PCC.

Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.

M&L for water proofing treatment over RCC slab by applying oil bound bituminous primer @ 0.30 kg/Sqm and providing and laying 3 mm thick APP modified water proofing memberane weighing not less than 3.50 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having soften point not less than 150°C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing strength of 180 N, torch application, side overlap 75 mm and end overlap 100 mm and tucked into the chases including ponding test all as specified and directed.

M&L for wire brushing and cleaning top surfaces of roof slabs etc, including washing the roof surface with water and making the surface free from mud etc complete all as specified.

M&L for 15 mm thick screed bed or bedding layer in cement mortar (1:3) on roof surfaces parapet or vertical beam surface (horizental or vertical) finishing the surfaces even and fair complete all as specified. (Note :- Course sand (Toka sand) shall only be used in screed bed/plastering.)

M&L for Lime concrete in lime mortar ratio (1:3) using 40 mm graded brick aggregate, laid to slope as directed by Engineer in charge over RCC roofs as padding complete alll as specified. Note: Minimum thickness of lime concrete at lower end shall not be less than 50mm.

M&L for 20- 22 mm thick factory made PCC tiles of size 250mm x 250mm with grey cement and no pigment , bedded in cement mortar (1:4) 15 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement complete all as specified.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing material as in benching, kerbs, mud stops, along side walls adjoining to roofs and similar items complete. (Water proofing material shall be measured and paid for separately).

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar (1:3).

Demolition of RCC of any description and in any position not otherwise specifically provided for, (reinforcement cut as required to facilitate demolition).

M & L for M-25 design mix concrete using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies, deck slabs and in shelves and the like, finished exposed surface fair and even. (Reinforcement and form work shall be measured and paid separately)

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) for flat rough surfaces of concrete.

M & L for TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of brick work masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and pre cast concrete articles.

M & L for Brick work using old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6).

M & L for Brick work using old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:4).

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4).

M&L for 75 mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement.

Excavation in trenches, not exceeding 1.5 metres wide and not exceeding1.5 mtrs in depth for foundations etc, not exceeding 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming of soil in layers not exceeding 25cm thick.

Removing excavated soil to a distance not exceeding 50 mrtres and depositing where directed at a level not exceeding 1.5 m above the starting point.

M & L for concrete bed to 150 mm bore dia of drain pipes including packing under, and haunching against the sides of the pipes after they are laid and tested; in PCC (1:3:6) type C2 using 40mm graded stone aggregate.

Cutting into existing manholes, sump for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete (1:2:4) type B-1 smooth finished, and reforming benching as required for 150mm dia pipe complete all as specified and as directed.

M&L for applying one coat of Dr Fixit Pidecrete URP in chajjas, staircase etc by using 2 Sqm per Kg URP + cement in the proportion (1:1.5) and making pidecrete solution and applying by brush etc all as directed.

M & L 75MM thick PCC 1:4:8 type D-2 using 20MM graded stone aggregate as in subbase complete all as specified and directed.

S&F 60MM thick coloured interlocking tiles of grade M-35 as per IS-15658-2006 of approve design laid over and including 25MM thick sand filling complete all as specified and directed.

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc including concealed conduit and sunken boxes and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium duty ISI marked) and conduit fittings with and including 3 mm thick bakelite laminated sheet top cover for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 175 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 175 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 175 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc.

All as per item No 175 above but for one light point controlled by two, two way switches .

S & F Switch, flush type, single pole, one way, 5/6 Amp .

S & F Switch, flush type, single pole, two way, 5/6 Amp .

S & F Switch, flush type, single pole, one way, 15/ 16 Amp .

S & F socket, multipurpose, 2 in 1, 5 Pin, 6 Amp, flush type. (Note: Switch and socket shall be of same make.)

S & F socket outlet universal, multipurpose, 2 in 1, 3 Pin 6 Amp and 6 pin 16 Amp, flush type. (Note: Switch and socket shall be of same make.)

S&F, fan regulator electronic step type (1-5), socket type 230-240 Volt, AC supply, complete all as specified and directed.

S & F ceiling rose, 3 plate, surface bakelite type, Polycorbonate body, 6 Amps, 250 Volts AC, 65 x 50 mm, three terminal (ISI marked) complete all as specified.

S & F 18/20 watt Retro LED tube light fitting, wall/surface mounted, IP 20 protection, conforming to IS 16106/IS 16107, minimum 6000K batten decorative type 4 feet long polycarbonate body, white, in built LED driver, power factor>0.95 , Make all as per Crompton Cat Part No. DMLN1LT8-16 (for batten) and Cat part No. LT8-20-865-2 (for tube light) including 18/20 watt tube rod or equivalent model of any make given in Appx 'B' connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting all as directed.

S & F surface mounted, decorative round plastic bulk head luminaire comprising of high brightness LED lamp 10/12 watt, 6000K polycarbonate including all other accessories and fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector. Make:-Crompton cat part No LBHE-10-CDL or equivalent model of approved make from list of make attached in tender documents including taking down old existing light fitting.

S & F energy efficient LED street light fitting of 45 Watt maintainable type with IP 66 degree of protection, PF > 0.95 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 5 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including 45 watt LED lamp with GI brackrt - 01 No, MS clamp-02 Nos suitable for walls/ columns and making electrical connection with providing of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as per SYSKA cat part No. SSK-SLR-45W or equivalent model of any make given in Appx 'B', Cat Part No. as approved by GE complete all as specified including taking down old unserviceable existing street light fitting of any type and capacity from pole along with accessories.

S & F, In repair, Lamp holder of PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb.

M & L in replacement of earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 6 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

S & F MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection including taking down old unserviceable MCB complete all as specified.

S & F MCB, SPN, 40 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCB, TPN, 63 Amps, 'C' curve , 415 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, IP-43 protection, 4 way, DB TPN 415 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S&F blanking plate.

Taking down old serviceable / unserviceable ceiling fan 1200 / 1400 mm sweep, 230 volts, AC, single phase, dismantling the ceiling fan and taking out complete rewinding (if unserviceable) for replacement of super enamelled copper winding wire of existing gauge and size including thoroughly cleaning all the components of fan, oiling and varnishing the fan with and including replacement of rusted bolts/nuts/split pin, rubber reel, flexible twin core cable of size 23/0/0.00076 approx one metre long for each fan, machine screws and painting the fan and writing MES No. on fan and re-fixing the fan all as directed.

S&F exhaust fan 300 mm sweep, 230 / 240 volts, AC, single phase with louver and connection with flexible twin core cable of size 23/0/0.00076 approx one metre long for each fan including taking down old serviceable / unserviceable exhaust fan 200 / 225 / 300 / 450 mm sweep, 230 volts, AC, single phase.

S&F ceiling fan 1200 mm sweep, single phase, AC, 230/240 volts, ISI marked, including hanging rod, fan hook including writing MES No on fan including taking down old serviceable / unserviceable ceiling fan 1200 / 1400 mm sweep, 230 volts, AC, single phase, fan.

Taking down old serviceable / unserviceable exhaust fan 300 / 450 mm sweep, 230 volts, AC, single phase, dismantling the exhaust fan and taking out complete rewinding (if unserviceable) for replacement of super enamelled copper winding wire of existing gauge and size including thoroughly cleaning all the components of fan, oiling and varnishing the fan with and including replacement of rusted bolts/nuts/split pin, rubber reel, flexible twin core cable of size 23/0/0.00076 approx one metre long for each fan, machine screws and painting the fan and writing MES No. on fan and re-fixing the exhaust fan all as directed. (Note: If at site any nos of geyser, ceiling fan, exhaust fan, electric meter is found before starting the work, the contractor shall hand over these items to Unit Rep in writing to avoid the last minute complicacies and refixing of electric meter is the sole responsibility of the contractor before handing over the site to user.)

M/s MITTAL CONSTRUCTIONS

SJM CONSTRUCTIONS

SHARDA ENTERPRIES

M/s Kamal Builders

FAQIR CHAND

M/S VERMA BUILDERS & DEVELOPERS