Internal and external upgradation works at Type-II Block-IV quarters in CSIR-CLRI Staff Quarters, Adyar, Chennai-600020

Amount

Civil Part

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing lime concrete manually/ by mechanical means including roof tile/tree growth and disposal of material within 50 metres lead as per direction of Engineering-charge.(or neatly dressed as per the dirction of engineering-in-charge)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster including wall tiles/unsound concrete/removing tree roots or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.[ Rubbish to be taken out of the CLRI campus at the risk and cost of the contractor or as per the direction of engineering-in-charge]

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering,shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand incuding manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 20% : 4 graded stone aggregate 20 mm nominal size of Recycled Concrete Aggregate (RCA) upto 20%).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls.Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto or above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished SS piano hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing bright finished brass hanging type twin rubber floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing chromium plated brass night latch with lock of six lever approved quality including necessary screws etc. complete. Make: Goodrej or equivalent

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws :30 mm thick shutters. With ISI marked stainless steel butt hinges of required size. Second class teak wood

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm including removing old mesh if any all complete.For UPVC windows/wooden mesh door

Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant inside/outside (rate including sealent) over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. Including, after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant inside/out side ( Rate including sealent) over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. Note:The rate are including scaffolding and power supply both should be apply the contractor.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Size of tile as per the direction of Engineer-in-Charge. Make: Kajaria or equivalent

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (Rate including fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.Make:Kajaria or equivalent.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size.Size of Tile 600 x 600 mm. Make:Kajaria or equivalent

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. (Two coats)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : (water proof primer for outer wall) Water thinnable cement primer

Distempering with 1st quality acrylic emulsion/distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats (Make: Berger Rangoli total care/Asian royale shine or equivalent)

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats. Make: Asian Apex ultima / Berger wheathercoat long life10 or equivalent

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Make: Berger or equivalent

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts (Rate including MS hold fast size of 40x5mm and 250mm long) in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. Door chowkhats

Removing dry or oil bound distemper, water proofing cement paint and the like by mechanical scrapping, sand papering and preparing the surface smooth including water washing wall surface (for removing dust/bungal growth/dark strain) with necessary repairs to scratches etc. complete.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with cement based polymer modified self curing mortar (equivvalent to SP-40 ), including disposal of rubbish, all complete as per the direction of Engineer-In- Charge.

Dismantling W.C. Pan/kitchen sink/washbasin of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Taking out existing wooden door shutter, repair by cutting, two coat of painting etc. and refixing of repaired door shutters to existing door frames, including replacement of SS hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), P/S-trap, conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps(jaguar or equivalent), 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board.610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

Providing and fixing 600/450x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. Make:Prayag or equivalent

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with G.I spl. clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes[ Note: Pipe to be closed after the pressure test sucessfully completed the rate including pressure testing]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with G.I spl. clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 50 mm nominal outer dia Pipes

Making connection of G.I. distribution branch with cpvc main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

Providing and fixing uplasticised PVC connection pipe Hot/Cold with brass unions : 45 cm length. 15 mm nominal bore.

Providing and fixing C.P. brass shower rose with arm 15 or 20 mm inlet : (Make: Jaguar or equivalent) 100 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :Make:Jaguar or equivalent. 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.Make:Jaguar or equivalent. 15 mm nominal bore

Providing and fixing C.P. brass angle stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore Make: Jaguar or equivalent

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and fixing PTMT grating of approved quality and colour. Circular Type 125 mm nominal dia with 25 mm waste hole

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:180x150 mm size P type(including dismantling existing gully chamber with trap).With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and fixing C.I. cover with frame for manholes :455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :For pipes 100 to 250 mm diameter

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing glazing in aluminium/UPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . :With float glass panes of 4 mm thickness (weight not less than 12.50 kg/sqm). Plain/pin headed

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs for all floor level, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.[Note: Shifting of materials not allowed through liftt machine provided for occupants. separate arragement may be made by the contractor at his risk and cost without disturbing the occupants.]

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers/polyurethane having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 1:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. Make:Fosroc Nito 725 or equivalent

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying/vertical the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @ 0.70 kg per sqm. Product- Fosroc or approved equivalent

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.Product- Fosroc orapproved equivalent

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. Make: KK precast or equivalent.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions with providing and fixing 20mm dia spout pipe, including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm).

Providing and fixing PVC floor Trap of Make: "Supreme" Size:- 110mm, Socket Type:- "S", Length:- 278mm, Depth of outlet:- 110mm & Height of Trap-118mm with necessary concrete bedding in floors with necessary cutting, placing, etc., complete all as required and directed by the Engineer-In-Charge.

Supplying and fixing Health facet ( not less than 1.2m length) of approved design including CP Angle cock with required cp fittings etc. as per direction of Enginner-in-Charge. Make: Jaguar or equivalent

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions for necessary stage work at duct area , including Providing and fixing G.I. coated Special clamps with bolt nut at 1m c/c or as required all complete at site conditions in all leads and lifts and as directed by the Engineer-in-Charge. 110mm dia.

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions for necessary stage work at duct area , including Providing and fixing G.I. coated Special clamps with bolt nut at 1m c/c or as required all complete at site conditions in all leads and lifts and as directed by the Engineer-in-Charge. 75mm dia.

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions , including required trenching upto 1.2m depth and refilling the same all complete as directed by the Engineer-in-Charge. 160mm dia.

Shifting of house holds to allotted quaters including all items like furniture , kichenware, storage units, electrical, electronics goods,(except Ac Unit) required installation and shifting back the same to renovated quarters without any damages and as per occupants positionsetc, complete as per the directions of Engineer-in-charge. Lead with in the staff quaters area upto all floor level. [ Shifting of all the items available at home including required transport, tools and plants etc]

Providing and fixing Euro designer tiles of EUROCON/ HINDUSTAN make of approved pattern and design mixed with pigment to match the shade of the slab for jointing complete with base of 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand).

Dismantling Existing pipes of any diameter inlet and outlet pipes for GI/Pvc/SWR/CI/sewer pipe all complete as per direction of site incharge (external work)including removal of clamps , making holes, fittings, removing and refixing of water meters etc.,complete taking out the pipes of any diameter of size, manually/ by mechanical means including stacking of pipes in departmental stores as per direction of Engineer-in-charge

Providing and fixing 30mm thick panel PVC door shutter with bend Beading consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc., and including SS Hinges and other fittings like 100mm Al.T-bolt, handles and 150mm sliding door bolt with ss screws etc.,complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.Both side deccorative.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, sheet properly joined with solvent cement adhesive as per sectional view.A mild steel square tube of size 19mm of 19 gauge is inserted inside to give extra structural strength. The door frame can be made with/without rubber gasket as required.if rubber gasket is not required then one strip of 5mm thickness can be eliminated and final size of choukhat will be 50mm x 42 mm.PVC door frame sections are cut in 45° and joined to each other perfectly 90°.'L' shape brackets made out of M.S.square tube are inserted inside the choukhat corners.These brackets are finally fixed using the steel screws from both the sides and including all necessary Aluminium fittings like tower bolt ,keel, Ms Screw handle etc complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment. Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: Anti-Termite Treatment- Post Construction Operation Details (i) Drilling at every one foot interval at wall and floor junction. (ii) Drill depth 4-5 inches on both sides. (iii) chemical used- Imidachloprid 30.5 S.C.[Bayer India or equivalent] (iv) Chemical injection done very half an hour up to saturation point(min 4-5 times). (v) Complete electrical conduits /junction boxes chemical treatment.[oil based] (vi) Plugging of holes after chemical injuction. (vii) On completion of work a warranty for a period 5 years is given for the site. (viii) Dliute and injecting Chemical emulision for POST CONSTRUCTIONAL anti-termite treatment (Including the cost of chemical emulsion) (ix) Treatment of existing mansory using chemical emulsion @ one litre per hole at 300mm interval full depth of the hole with Imidachlopride chemical.The hole filled with white/grey cement as directed by the engineer-in-charge[ Plinth area will be measured for payment]

Steel work for pipe clamp stand on the wall including welded in built up sections/ framed work, cutting, hoisting , fixing position in the wall with cement concrete, 1:2:4 (i cement: M-sand:20mm aggregate) making hole on the wall and making good with the required cement plaster , applying a suitable priming coat of approved epoxy primer and two coats of epoxy paint all complete as per the direction of engineering in charge.

Polishing in high gloss finishing of existing SS handrail including removing of strain and replacement of damaged/discolored portion of ss pipes etc all complete as per the direction of Engineering-In-Charge.[Note: Coefficient 0.5 for each side of the handrail area will be measured for payment. No extra will be paid ]

Repair and Replastering of chejja/sunshade/structural members/fins including cutting(dismantling) of concrete/plaster, making slope of top portion with micro concrete upto 50mm thick,applying Nito coat bonding agent of old surface, required centring,shuttering,propping and removing, plastering with SP-40(Fosrac or equivalent) repair mortar top and bottom of the chejja, providing drip mould of 25mmx25mm in the bottom, required water roofing material, required scaffolding upto floor five level etc all complete. As per the direction of engineer-in-charge. (Note: Rate including drip mould 25x15mm. Finished chejja area will be measured for pyament)

Providing and fixing of brass finished magic eye piece with clear visibility and suitable for 30 to 35mm door shutter including making holes in the shutter and making good as per dirction of enginner-in-charge. (as per sample approved by engineer-in-charge)

Providing and laying sunken floor filling with CLC concrete blocks of 1:5:10 (1 cemnet: 5 M-sand: 10 CLC aggregate 40mm nominal size) including all leads and lifting etc as per the direction of Engineer-In-Charge.

Civil Part - Buy Back Items

Buy-back of existing/damaged wooden/pvc door/Alwindows/Ms windows of frames, shutters, glazing, fittings all complete including dismantling and making good the brick work etc as per the direction of In-Charge. Any size.

Electrical Part

MODULAR LIGHT/FAN PT: Wiring for light / fan / exhaust fan / call bell point with 1.5sqmm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable size GI. box and earthing the point with 1.5sqmm. FRLS PVC insulated copper conductor single core cable etc., as required. Make: FINOLEX/ANCHOR ROMA/HAVALLS

Twin Control light point: Wiring for Twin control point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. as required. Make: FINOLEX/ANCHOR ROMA/HAVALLS

A.C. POINT: Supplying and fixing two modular G.I box for each socket & MCB with modular plate and cover on surface/recessed including providing and fixing 25A socket outlet and 25A modular SP MCB,"C" curve including connections, testing and commissioning etc.as required. Make: Legrand/L&T/MK

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required MAKE: HAVALLS/FINOLEX/POLYCAB 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required MAKE: HAVALLS/FINOLEX/POLYCAB 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required MAKE: HAVALLS/FINOLEX/POLYCAB 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

ELECTRONIC BELL/BUZZER: Supply and fixing Electronic bell/buzzer suitable for single phase,230V, complete with connection,testing etc. as required. MAKE: ANCHOR/PHILLIPS/HAVALLS

MODULAR 15A SWITCH : Supplying and fixing following modular switch on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 15/16 amp switch

MODULAR 15A SOCKET : Supplying and fixing following modular socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 6 pin 5/16 amp socket outlet

MODULAR 5A SWITCH : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 5/6 amp switch

MODULAR 5A SOCKET : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 5/6 amp socket

MODULAR TV ANTENNA SOCKET: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND TV antenna socket outlet

ELECTRONIC FAN REGULATOR: Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND

SINGLE PHASE DB : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator) Make: Legrand/L&T/Havells 16 way, Double door

SINGLE POLE MCB FOR DBs: Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. Make: Legrand/L&T/Havells 5 amps to 32 amps Single pole

INCOMER FOR DB (DOUBLE POLE ISOLATOR): Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required. Make: L&T/Legrand/Havells 40A

SP Blanking Plate: Supplying & fixing of single pole blanking plate in the existing MCB DB complete etc. as required.

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 2 Module (75 mm X 75 mm)

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 3 Module (100 mmX75 mm)

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 6 Module (200mm x 75mm )

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 12 Module (200mm x 75mm )

LABOUR CHARGES FOR Fixing of Exhaust Fan: Installation of Exhaust fan in the exsting opening, including making good the damage, connection, testing, commissioning with 1.5 sqmm FRLS PVC insulated, copper conductor, single core cable etc. as required

Labour Charges for Fixing of louver/shutter for Existing exhaust fan: Extra for fixing the louvers/shutters complete with frame for a exhaust fan of all sizes

PVC BATTEN/ANGLE HOLDER: Supplying and fixing PVC batten/angle holder including connection etc.as required. MAKE: ANCHOR ROMA/MK/LEGRAND

LABOUR CHARGES FOR FIXING OF FLUORESCENT/MIRROR LIGHT FITTING: Installation, testing and commissioning of pre-wired, fluorescent/Mirror light fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connections with 1.5sqmm FRLS PVC insulated, copper coductor, single core cable and earthing etc. as required.

Ceiling Fan 1200mm: Supply, Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, Ceiling fan with Brush Less Direct Current(BLDC) Motor, Class of Insulation : B, 3 No's of blades, 30 cm long down rod, 2No's canopies, shackle kit, safety rope, copper winding, Power factor not less than 0.9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min,350 RPM (tolerence as per Is:374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 deg C(max),insulation resistance morethan 2Mega ohm, suitable for 230V,50Hz, single phase AC supply, earthing etc complete as required. MAKE: Orient/Almonord/Crompton

PVC Pipe 25mm: Supplying and fixing of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm Make: Vasavi/Avonplast/Finolex

REMOVAL OF ELECTRICAL ITEMS: Removing the existing connection,wires, unused metal enclosures, switch boards, fixtures,ceiling fans,exhaust fans,DB's.etc., and same have to be haneded over to department as directed by dept, Engineer.

EXHAUST FAN: Supply of 225mm Sweep Exhaust fan with metal type model for kitchen/bathroom complete with all accessories.. etc, as required . Make: Havells / USHA/ Almanord/Crompton

20W 4Ft Light fitting : Supply of 4ft 20W 6500K 2000lumen LED/Conventional type Light fitting with fixing accessories on surface /wall etc. as required. Make: Crompton/ Philips/Havells/Wipro

MIRROR LIGHT FITTING : Supply of 9W LED mirror light suitable fitting (Crompton/ Philips) to complete with all assocessories etc., as required. Make: Crompton/ Philips/Havells/Wipro

18W LED Surface Fitting: Supply & fixing of 18W LED 6500K (595mmX595mm) Surface fitting round/square light suitable fitting including Installation, testing and commissioning of pre-wired, fluorescent/Mirror light fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connections with 1.5sqmm FRLS PVC insulated, copper coductor, single core cable and earthing etc. as required. Make: Crompton/ Philips/Havells

Making hole50mm in Wall : Making hole through wall & providing PVC pipe (50mm) for installation of AC outdoor unit pipe & cable by demolishing brick work manually and the same as good finishing of wall by plastering etc as required.

Shifting of AC Unit: Removing, Shifting & refixing of Air conditioning unit (upto 2ton) split type with existing out door unit stand and supply of copper tube 3m chord wire with insualtion white tape including gas refilling & other accessories as required for fixing at new loaction as directed by dept Engineering incharge.

METERING PANEL: Supply, erection & commissioning of wall/floor mounting type of Energy Metering panel board fabricated with suitable size 14 SWG MS sheet/flat/angle duly painted and also suitable for Indoor installation and earthed consisting of the following as required: (a) Incomer: One chamber consisting of suitable size with mounting arrangements,supplying and fixing of 1no 125A TPN MCCB (Make: L&T/Legrand/Simens) (b) Out going : 9 No's 32A Double Pole MCB (Make: L&T/Legrand/Simens) The above MCCB/MCBs should be L&T/Legrand/Simens make and to be mounted in individual chambers consisting of suitable suitable size with mounting arrangements. (c) Suitable size epoxy insulated colour coded Copper bus bars chamber along with Aluminium earth bus for entire system. (d) Interconnection with suitable size insulated Copper link,spreder,provision of inscription labels etc. (e) Removing & refixing the exsisting EB Meters(9No's) and including outgoing wires end terminations.etc., (f) Suitable cable chamber with knock out holes, terminal blocks, interconnection materials etc.as required. (Work may be coordinated with TNEB if required) (g) Meter shifting charges payment to EB born by CLRI/reimbursement

JPS Constructions

JPS Constructions