SPECIAL REPAIR TO OTM ACCN (BLDG NO P-05, P-08, SP-30) AND MD ACCN (BLDG NO P-03) AT SUKNA STN UNDER GE SUKNA

Amount

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and fair, complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M&L preparing old plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and as directed.

M&L preparing old plastered surfaces of walls and applying two coats of white wash, complete all as specified and as directed.

M&L for applying two coats of Birla/Asian wall care Putty (total thickness not less than 2mm) after preparation of old/new wall/ceiling surfaces, complete all as specified and directed.

M&L for preparing new surfaces of walls duly applied with wall care putty, applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for preparing new surfaces of ceiling,duly applied with wall care putty, applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for complete removal of existing treatment of ceiling, preparing the new surfaces of ceiling duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M & L for preparing old treated surfaces of wall and applying one coat of oil bound distemper, white or any tint as approved, complete all as specified and directed.

M&L for preparing newely plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed

M&L for preparing Old plastered surfaces of wall and applying one coat of cement base paint, complete all as specified and as directed.

M&L for complete removal of existing treatment from the external surfaces of wall etc, thereafter prepartion the surfaces and applying two coats of cement base paint, complete all as specified and as directed.

M&L preparing new surfaces of walls duly applied with wall care putty, applying two coats of exterior emulsion weather coat paint over & including one coat of primer, complete all as specified and as directed. Note : Provision of wall care putty not included in this item.

M&L for complete removal of existing treatment from the external surfaces of wall, prepartion of the new surfaces of wall duly applied with wall care putty, thereafter applying two coats of exterior emulsion weather coat paint over & including a coat of primer, complete all as specified and as directed. Note : Provision of wall care putty not included in this item.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 20 above but 20 mm bore.

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item No 22 above but 20 mm bore pipes.

Fixing only of 15mm bore GI tubing, medium grade with provision of new G.I. fittings as required and fixing accessories in new or old position (partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, including cutting chases of the required size, making good of the same in CM 1:3 to match with the adjoining surfaces) including testing, complete all as specified and directed.

Fixing only of 20mm bore GI tubing, medium grade with provision of new G.I. fittings as required and fixing accessories in new or old position (partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, including cutting chases of the required size, making good of the same in CM 1:3 to match with the adjoining surfaces) including testing, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kg/Cm2), straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed.

M&L for Brickwork with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kg/Cm2), straight or curved on plan exc 6m mean radius, built in Cement morter 1:4, complete all as specified and directed.

M&L for brick work with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kg/Cm2), straight or curved on plan to any radius, built in CM 1:4 as in half brick thick walls, complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

M&L for complete removal of existing treatment of walls, preparing the surfaces of walls duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of approx size 260 x 580 x 440mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, complete all as specified and directed (The pan shall be of make : JAQUAR : Cat No. CHS-WHT-OP01 or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, as approved by the GE)

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 610x480x195 mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed (The basin shall be of make : JAQUAR : Cat No. FNS-WHT-40801 or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE)

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed (The bib tap shall be of make : ESSCO : Cat No. SQT-511KN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs Grating doom 100mm dia of PTMT (minimum weight 25 gms), complete all as specified and as directed.

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed (The stop valve shall be of make : ESSCO : Cat No. SQT-513KN/SQT-513BKN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed (The stop valve shall be of make : ESSCO : Cat No. SQT-514AKN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and as directed.

S&F in repairs stainless steel kitchen Plate Rack,of approx size 31"x36"x10", Cat No P-348 of Prayag polymers Pvt Ltd or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs Swivel shower of PTMT, any colour (minmum weight 40 grams) for fixing with 15mm bore pipe, complete all as specified and as directed (The shower shall be of Cat No. 181 of Prayag Polymers Pvt Ltd or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed (The Shower Rose & Shower Arm shall be of make : Prayag Polymers Pvt Ltd : Cat No. BOS-11 & BOS-48 respectively or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs high dencity polyethylene pipes (HDPE) pipes, 40mm bore of pressure rating 6 kgf/cm2, to wall,ceiling or floors etc, complete all as specified and as directed.

S & F 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary standard PVC stay clamps etc and/or laid in trenches, complete all as specified and directed. Notes : (i) Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured and paid for separately.

S & F 75 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary standard PVC stay clamps etc and/or laid in trenches, complete all as specified and directed. Note :- Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured and paid for separately.

S&F 110mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F 75mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F in repair Soap dish, PTMT, Cat No. 1951 of make PRAYAG or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, as approved by the GE, to wall with and including plugs, with chromium plated screws and wooden/plastic cleats, complete all as specified and directed.

M&L for providing 50mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

Taking down existing un-servicable waterproofing treatment from roof slab surfaces (including roughening of old concrete surfaces by picking), cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.00 kilogram of cement per square metre over roof surfaces etc, providing 15 mm thick plastering in cement mortar 1:4 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 3mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove as well as damaged surfaces of the wall after tackling of membrane in CM 1:3 to match with the adjoining surfaces.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

S&F Aluminium Hat and coat hooks , solid body, 175 to 250mm, complete all as specified and as directed.

S&F brass Magic eye to shutters, complete all as specified and as directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

S&F in repairs angle valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed, (The angle valve shall be of make : ESSCO : Cat No. MQT-526KN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs, vitreous china urinal, 1st quality, Half Stall Type, white (excluding flushing cistern, flush pipe) but with & including grating, union for discharge pipe, also including provision of PVC waste pipe and all the fixing accessories, complete all as specified and directed, (The urinal shall be of make : JAQUAR : Cat No. URS-WHT-13257 or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S&F in repairs for 75 mm bore outlet cast floor trap with and including grating, also including jointing to waste pipe and provision of cement concrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S&F in repairs sink with drainage board made of 0.80 mm thick sheet of stainless steel (Bronze range 204 super steel : Matt) for kitchen or laboratory with and including plugs, washers, wastes; 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall approx size 914mm x 460mmx203mm with bowl size 405mm x 354mm x 203mm, Make Prayag : Cat No. 939-DM or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern), 1st quality, white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, Make - Jaquar : Cat No. CNS-WHT-551SN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consisting of sheet glass shelf 125mm wide with chromium plated bracket guard and railing 50cm long, Make- Prayag : Cat No. BEA-45 or equivalent of make Pollytuff as approved by the GE, complete all as specified and as directed.

S&F in repairs Pillar taps with Arrestor , fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, Make : ESSCO : Cat No. SQT-508KN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, or approved by the GE, complete all as specified and as directed.

S & F in repairs soap dish, brass chromium plated, fixed to wall with and including plugs & chromium plated screws, Make- Prayag : Cat No. BA-85 or equivalent of any other make as approved by the GE, complete all as specified and as directed.

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F steel work in tubular purlins, rafters, fan hooks & similar work including special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, also including necessary welding etc and applying one shop coat of Zinc Chrolomate primer after prepation of the surfaces, complete all as specified and as directed.

Dismantling water tanks exc 500 litres but not exc 1000 litres capacity including disconnecting the connections, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 25mm bore (Minimum weight 455 grms), complete all as specified and as directed, (The ball valve shall be of make : Prayag : Cat No. 153 or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, as approved by the GE).

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 455 grms), complete all as specified and as directed, (The ball valve shall be of make : Prayag : Cat No. 152 or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, as approved by the GE).

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S&F of GI frame work (size of grid 600mm x 600mm) for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of Hangers of 4mm dia G.I wire (length as required at site), complete all as specified and as directed.

M & L for Anodised aluminium snap gride (size of grid605 x 605 mm) frame work for false ceiling (including provision of supporting hanger consisting of 6mm dia mild steel rod, J-bolts with necessary bolts, nuts and washers all as directed) complete in all respects as specified in Paras 10.38 & 10.38.1 of MES Schedule Part 1 and as directed.

Providing and fixing Gypsum board 12mm thick in ceiling fixed with screws as per manufacturer's instrucitions, jointing with & including fiber tape jointing compound, applying two coats of plastic emulsion spray painting over a coat of primer after preparation of surfaces and also including making openings/spaces for fixing of light fittings, complete all as specified and as directed. Note :- Design of ceiling will be as directed/approved by the GE.

S & F 4mm thick Non-asbestos fibre cement building boards (4mm thick pre-painted designed type E-Board) to aluminium frame work with screws in ceiling (flat and/or slopping) and in jointless finish with & including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Note :- The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.

M&L for provisioning of decorative type POP finishing of approx 100mm girth and 10mm thick as in cornice or junction of wall and ceilling, complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position like trusses, rafters, purlins etc.

M&L for Second class hard- wood as in timber, clean swan scantlings, complete all as specifiied and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sub-base of floors etc, finished even & rough, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) (including tiles etc) of any description & in any position not otherwise specifically provided for (including W.C's Sunken floors etc), also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for cement concrete 1:5:10 type E-2 (using 40mm graded stone aggregates) as in sunken portion of WC etc, complete all as specified and as directed.

M&L for brushing neat cement slurry with 1.00 kilogram of cement per square metre over sunken floor surfaces etc, providing 10 mm thick plastering in cement mortar 1:3 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M&L for applying evenly bituminous tack coat @ 1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per Sqm on the surfaces of the sunken floor , complete all as specified and as directed.

S&F in repairs for 75 mm bore outlet uPVC (SWR) floor trap with and including grating, also including jointing with solvent cement and provision of PCC 1:2:4 (type B-1 : using 20mm graded stone aggregates) block of required size for fixing of floor trap, complete all as specified and as directed.

S&F in repairs Brass chromium plated bottle traps of 32 mm bore for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap, Make- MARC : Cat No. MOR-1350 or equivalent of make JAQUAR as approved by the GE, complete all as specified and as directed.

M&L for 18 to 20mm thick machine cut, pre-polished Black Jet, premium quality, granite stone slab, in skirting, Kitchen platform, dado etc laid over and including 15mm thick CM 1:4 screed bed, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone including rounding / moulding the edges half round, complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, stainless steel, 600mm long between flanges, Make : JAQUAR : Cat No. 1111SM or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs stainless steel curtain rail of 20mm bore, complete all as specified and directed.

S&F brackets and funnel caps suitable for the curtain rail to be provided under Item No. 93 above, complete all as specified and directed.

M&L for post anti-termite treatment at points of contact of wood work by chemical emuision (in oil or kerosene based solution ) @ 0.50 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same, complete all as specified and as directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in flooring, finished even and smooth w/o using extra cement, complete all as specified and directed.

Taking down of steel windows, vents (including grills/guard bars, where occurs), including cutting holes for removing the lugs etc, also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, also including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per item No 98 above but steel window without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

M&L for the Framed work such as framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

Hacking out old broken glass any thickness, size, quality and description from metal frames including punching or drilling out old glazing pins /springs clips, complete all as specified and directed.

S&F 3mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 3mm thick Figured glass, pin head type and glazing for Aluminium Joinery or for steel surrounds with & including oil putty for steel surrounds, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces of any description duly applied with shop coat of primer, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in this item.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed.

Roughning surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainless steel wire staples etc, complete all as specified and as directed.

Dismantling of loose / designtegrated portion of RCC chajja , bands , shelves , beam ,RCC railing , balcony and similar work ( including provision of support , formwork and welding of reinforcement with coating of anti corrosive chemical to the exposed surfaces of reinforcement) and dubbing with PCC (1:2:4), 15 to 25 mm thick using 6 to 12 mm graded stone agg mixed with WPC after applying cement slurry @ 3 kg/sqm and finished even and smooth to desired shape for triple storey bldg, complete all as specified and as directed. Note : (i) Only WPC shall be measured and paid separately. (ii) For the payment purposes, only volume of PCC 1:2:4 shall be considered.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

M & L for PCC (1:3:6) type-C2 (using 40 mm graded crushed stone aggregate) as in surface channel and drains including necessary form work, complete all as specified and directed..

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement (cost of cement also included), including forms, moulds, mitred/stopped ends etc, complete all as specified and directed. Note : For rate adjustment (Addition/deduction), 10% of the quoted rate of the above item shall be considered for each 25mm girth or part thereof over or under 30cm inner grith.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for 400mmx150mm coloured Non skid ceramic tiles 7 to 8 mm thick, in vertical surfaces such as skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick cement morter backing coat in CM 1:4, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 200mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:6, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in CM 1:3 mixed with pigments to match the colour of the Tiles (in separate process), complete all as specified and directed.

S & F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown in drg for SI No. 8095 on Ser Page No. 160 in SSR-2010 (Part-II).

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail, on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as shown on drawing on Srl Page No 156 of SSR Part-II, complete all as specified and as directed.

S&F Factory made wire gauged Solid Panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling shall be of wire gauze, the wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes, the wire gauge shall be stretched to tighten firmly, all as shown on page No 159 of SSR Part-II, complete all as specified and as directed. Note : Cost of wire gauge shall also be deemed to be included in the quoted rate of above item.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down shutter of any description area exc 1.00 Sqm and not exc 2.00 Sqm each, complete all as specified and as directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F factory made IInd class Hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35mm thick plain framed, panelled shutters ( Two panels),with lock rail and penel of 9mm BWP commercial ply or 12mm veneered particles board with commercial veneering on both faces. the size of rail and stile as per IS 1003 (Part-I), complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 30 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter, moulded type, solid core construction with particle board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for hold-fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to steel trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

M&L for Light Shade Polished Glazed Vitrified Tiles 9mm to 10 mm thick (square/ rectangular) of approved size, area of each tile not exceeding 0.36 Sqm in floor, set & laid over and including 20mm thick screed in CM 1:6, jointed & pointed in white cement mixed with pigment to match with the shade of tiles, complete all as specified and directed.

M&L for Light Shade Polished Glazed Vitrified Tiles 9mm to 10 mm thick (square/ rectangular), each tile of size 600 x 150mm as in skirting etc. on the vertical surfaces, set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shalde of the tiles, over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for coloured Glazed ceramic digital glossy tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for 18 to 20mm thick Machine cut kota stone slabs of size 590mm x 590mm in flooring, laid over and including 20mm thick screed in cm 1:6, set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed.

M&L for 18 to 20mm thick machine cut and prepolished kota stone slab in single piece as in skirting, landing, risers and treads of the steps (including making 3 groves on the Kota Stone Treads) over and including 15mm thick cement mortar bed in CM 1:4, jointed and pointed with grey cement slurry mixed with pigment to match with the shade of the slab, including moulding / rounding to the edges of the slabs, complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed

S&F 75mm size butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed

S&F Aluminium anodised barrel tower bolt 150 mm long of extruded section, complete all as specified and as directed.

All as per item No 141 above, but 125 mm long.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 125 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 100mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F mild steel Helical door spring 150mm long, ordinary rat tail rod pattern including roaller & roller plate, fixed with and including screws to wooden frames or with welding to steel frames, complete all as specified and directed.

S&F Floor door stopper (Overall length of cover plate 150mm) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold fast blocks, lugs blocks, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

Taking down of Aluminium joinery (including chowkat, fittings etc), including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the debris outside the premises, complete all as specified and as directed.

S&F standard aluminium powder coated section (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by the GE) as in frame, shutters for doors, windows / ventilators, partitions, kitchen cabinate, kitchen almirah, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) Cost of all the items / accessories including aluminium mongres required for the entire completion of the work shall be deemed to be included in the quoted rate. However Particle Board Panels, glass panes and wire cloth shall only be measured and paid separately under respective items.

S&F Prelaminated particle board 9 mm thick, exterior grade,prelaminated on both sides with decorative choice lamination, as in panels for aluminium joinery, complete all as specifiied and directed.

All as per item No 154 above but in squares n: exc 0.50 sqm in each pane, complete all as specified and as directed .

S&F, mild steel, cold rolled, Parliament hinges with 125mm width of recess between flanges (when open), complete all as specified and as directed.

S&F aluminium anodised tower bolts 100mm long of extruded section, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Taking down existing shutters for carrying out the civil repairs and refixing of shutters with frame of any description n.exc 1 sqm each after making necessary civil repairs, complete all as specified and directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with and including galvanised wire staples etc, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position as in kitchen shelves, cooking platform, lintels, chajja, beams, slabs etc not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L for TMT bars 8 mm dia bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Fins, fascias, louvres, parapets, and the railings exceeding 60cm in height and similar articles, complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Chajjas, complete all as specified and directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in slabs supported on walls, beams and and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type, A-1 (using 20 mm graded stone aggregates) as in lintel bands, lintels & beams upto 1.5 metre clear span and the like including use & waste of form work, complete all as specified and as directed. Note:- Reinforcement shall be measured and paid for seperately.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspected slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to Fins, louvres, fascia for rough flat surfaces of concrete, complete all as specified and as directed.

M&L for 12mm thick plywood, grade BWR, type BB, fixed with and including screws to timber frame work as in cub board shelves/Partition etc, complete all as specified and as directed

M&L for 18-19mm thick, prelaminated partical board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shutters, partitions etc, also including provisioning of 2nd class hard 4mm thick beading on exposed edges of partical board, complete all as specified and as directed.

M&L for standard cover fillets, 4.5mm thick of hard board, width 40mm and fixing with & including screws, complete all as specified and as directed.

S&F 100mm size Hasp and staple, aluminium anodised, safety type and fixed with & including screws, complete all as specified and as directed.

Taking down existing 100mm/75mm bore C.I. pipe including CI fittings from the wall surfaces, laid on the floor surfaces or from the trenches etc, complete all as specified and as directed. Note:- Excavation & Earth work shall be measured & paid for separately.

S & F in repair health faucet brass CP with 1 metre long Braided tube & wall hook, make : Prayag Cat No, BEA-85 or equivalent of any other make as approved by the GE, complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring (light / fan / socket or power point) complete, with all unserviceable fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity),metal plug socket DB(incl MCBs etc) and making good the disturbed surfaces, complete all as specified and as directed.

Taking down existing unserviceable submain wiring (including conduit /casing -caping), any size and making good the disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 186 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 186 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed

All as per item No 186 above but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per item No. 186 here - in - before but for one light point controlled by two, 2- way switch.

All as per item No 186 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn in and including PVC casing-caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with & including all accessories, fittings, PVC junction Boxes etc, also including 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made Modular Metal Flush Box with modular white cover plate and Frame suitable for modular switches, sockets, fan regulators etc, testing on completion, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 192 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 192 above but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per item No 192 here-in-before but for one switch socket outlet, 5 Amp on the same board, complete all as specified and as directed

All as per item No 192 above here-in-before but for one loght point controlled by two, 2 way switch.

All as per item No 192 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.50 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity earth wire, complete all as specified and as directed.

Supply and fixing switch socket out let multipurpose, 3 pin, 15 amp and one 3 pin, 5 amp, controlled by one switch, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

S&F socket outlet, 5 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F switch, flush type, 5 Amps, SP, two way, complete all as specified and as directed.

S&F bell push, flush type, 5 Amps, complete all as specified and directed.

Supply and fixing modular switch, one way, 6 Amps, 1 module, complete all as specified and as directed.

Supply and fixing modular switch, one way, 16 Amps, 1 module, complete all as specified and as directed.

Supply and fixing modular Bell push, 6 Amps, 1 module, complete all as specified and as directed.

S & F modular socket 16A-2/3 pin, 2 modules, complete all as specified and as directed.

Supply and fixing modular socket 6A-2/3 pin, 2 modules, complete all as specified and as directed.

Supply and fixing modular fan regulator, 120W - 2 module, complete all as specified and as directed.

Supply and fixing modular switches, 2 way, 6 Amps, 1 module, complete all as specified and as directed.

S&F Buzzer Ding Dong, AC, 230 Volts, single pole, complete all as specified and directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, 5 step not less than 100 watt, complete all as specified and directed.

Supply and Fix Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

Supply and Fix LED Lamp, 9 watt, retro fit, complete all as specified and directed.

Supply and fixing indoor LED 18/20 watt luminaires (4 Feet Lamp) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-20-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL's as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing indoor LED 10 watt luminaires (2 Feet LED Lamp) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-10-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing in repairs Bulkhead LED 10 watt luminaires, complete with all inbuilt accessories, prewired, make HAVELLS : Cat NoHEXAFT 10W LED 857 SSYM BOPC IP66 or equivalent of make BAJAJ/PHILIPS/CROMPTON as approved by the GE, including provision of twin twisted copper conductor flexible wire, complete all as specified and as directed.

Supply and Fix 36 Watt recessed full lit Luminaire with glare free uniform ileumination including provision of copper conductor cable for connection, complete all as specified and as directed. Make - Crompton Cat No : LCTLRNE-36-FO-WW or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note for Item No 219 to 220:- For payment purposes, 2 runs of main cable (each of 1RM), 1 run of earth continuity cable (1RM) and one run of conduit (1RM), all together shall be considered as "1RM".

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCCBs DBs, Double Door, phosphatised, Powder coated , Triple Pole and Neutral (TPN), VERTICLE TYPE , 4 way, 415 Volts, complete with and including 200 Amps rated bus bar, also cutting nitches/opening in the wall for accommodating the DB's, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and as directed .

S & F MCCB 125 Amps, 16KA, 4 Pole, 415 Volts, complete all as specified and directed.

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC casing-caping, complete with fittings, PVC Junction Boxes, fixing accessories, also including making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed. Note for Item No 223 & 224:- For payment purposes, 2 runs of main cable (each of 1RM), 1 run of earth continuity cable (1RM) and one run of casing-caping (1RM), all together shall be considered as "1RM".

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.00 sqmm as earth continuity conductor drawn through and including PVC casing-caping, complete with fittings, PVC Junction Boxes, fixing accessories, also including making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , single pole and neutral (SPN), 240 Volt , 8 Ways with and including 200 Amps rated bus bar, also cutting nitches/opening in the wall for accommodating the DB's, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and as directed .

S&F MCB 'C' Series, SPN, 40 Amp, 240 Volts, reputring capacity 10 KA, complete all as specified and directed.

Supply and fixing MCB,Single Pole, C series, 10kA ruputring capacity, 6 to 32 Amps, 240 Volts, complete all as specified and as directed.

Materials and labour for earthing complete with galvanised earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 metre below normal ground level with top edge of the plate not less than 1.50 metre below normal ground level) connected to galvanised lead earth wire 4.0 mm dia by means of bolts, nuts, washers and check nuts of galvanised iron or steel, GI earth wire protected by 15mm bore light grade galvanised iron pipe, including provision of 20 mm bore medium grade GI water tubing, wire mash funnel, charcoal or coke and common salt fillings and testing on completion as shown on electrical plate No.5 of SSR Part-I. including taking out unserviceable one, complete all as specified and directed. Notes : (i) Cost for provision of earth lead and protection pipe upto 7.50 metre length (from Earth Plate to Test Point) is deemed to be included in the quoted rate of above item. (ii) Cost of of necessary excavation & earth work, PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in earth pit, 50mm thick precent RCC 1:11/2:3 type A-1 (using 20mm graded stone aggregates) cover reinforced with 8mm dia mild steel TMT bars @ 10cm C/C both ways and all other relevant works, shall also be deemed to be included in this quoted rate of above item.

Supply and fixing in repairs, single pole and neutral enclosure, with & including a two pin and earth plug and socket, also with and including one number double pole, MCB, 20 Amps, 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

S & F in repairs for galvanized iron tubing 40mm bore light grade with all fitings for cable protection, along poles /wall/floor including necessary clamps, bolts, nuts,etc, complete all as specified and as directed.

Taking down of existing ceiling fan, 1200 mm/1400mm sweep, 230V, SP, rewinding of fans with the super enamelled copper wire of same gauge/size as per existing, replacement of ball bearings, carrying out other minor repairs as required to make the ceiling fans fully functonal, refixing of the fans, also making connection with and including copper conductor cable from ceiling rose to fan, complete all as specified and as directed.

Taking down and refixing of ceiling fan/Exhaust fan of any size and sweep including making connection by providing 3 core 1 Sqmm flexible copper conductor wire ,complete all as specified and as directed. Note: The unit rate also includes for necessary cleaning, minor servicing like greasing, lubricating etc to fans etc.

Taking down of old serviceable DB with MCBs and refixing the same in existing place, complete all as specified and as directed.

Taking down of old serviceable items like Tube lights, ceiling lights and refixing the same in existing place, complete all as specified and as directed.

Taking down of old serviceable items like switches, sockets, switch sockets, metal plug sockets, fan regulators, call bells and refixing the same to existing place, complete all as specified and as directed.

Taking down of existing Under Ground cable from trenches/ along wall/pole etc, complete all as specified and directed. Note :- Excavation & Earth work shall be measured & paid for separately.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 35 Sqmm 31/2 core laid in trenches /along poles/on wall etc, complete all as specified and as directed Note : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

S&F ceiling fan, ISI marked, white in colour, 1400 mm sweep, 230V, SP, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, also including taking down of existing Fan and depositing the same in MES store yard of GE, complete all as specified and as directed, Make : Usha model ENERGIA ISI marked or Equivalent of make Havells/Bajaj as approved by the GE.

S&F in repairs Exhaust fan, 300mm sweep, 230 V, Single Phase, metal body complete with and including accessories, luovers, anchoring bolts, nuts, washers, making opening for fixing of the Exhaust Fan and making good the surfaces of the opening with CM 1:3 to match with the existing surfaces and provision of PVC copper conductor cable for making connection with ceiling rose, complete all as specified and as directed. Make:- USHA Model No TURBO HDEF900RPM ISI GREY or equivalent model of make CG/HAVELS/Bajaj/Orient as approved by the GE. Note : The existing E.F. shall be the property of the Govt. & the same shall be deposited by the contractor in MES store yard.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc, complete all as specified and directed

Removing excavated material to a distance not exc 50.00 metre and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn in and including PVC casing-caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with & including all accessories, fittings, PVC junction Boxes etc, also including 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 245 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 245 above but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per item No 245 here-in-before but for one switch socket outlet, 5 Amp on the same board, complete all as specified and as directed

All as per item No 245 here-in-before but for one long point controlled by two, 2-way switch, complete all as specified and as directed

All as per item No 245 here-in-before but for one 15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.50 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity earth wire, complete all as specified and as directed.

M/S JYOTI SHARMA AND SONS

MS ORIENT ENGINEERING WORKS

M/S MANA ENTERPRISE

M/S B D ENTERPRISE

M/S TARAN INFRACON