REPAIR AND MAINT OF WALL MOUNTED PANELS, EARTHING INFRASTRUCTURE, AVIATION LIGHTS AND RUNWAY LIGHTS, HANGER LIGHTS, MEDIUM BAY LIGHTS AND ASSOCIATED E/M WORKS AT OLD AND NEW CANTT PATIALA UNDER GE (N) PATIALA

Amount

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frame 40x40x6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I

M & L for Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire complete all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.0 Sqmm Copper conductor Earth wire shall be measured as one unit) Note 2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring is included in quoted rates

Supply and fix in replacement of MCB SP up to 6-32 Amp all as specified and directed. (Note: MCB should be B curve as directed by engineer in charge)

Supply and fix in replacement of MCB SPN 6-32 Amp complete all as specified and directed. (Note: MCB should be B curve as directed by engineer in charge)

Supply & fix in replacement of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The DB shall be fiush fixed and making good the disturbed surface shall be part of job at no extra cost shall be paid on this account.

Supply & fix in replacement of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 4 way double door type with 200 amp rated bus bar. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The DB shall be fiush fixed and making good the disturbed surface shall be part of job and no extra shall be paid.

Supply and fix epoxy power coated MCCB distribution box double door VTPN 4 way vertical type AC 415 V with IP 43 protection for MCBs alongwith provision of MCCB as incomer with commen bus-bar at incoming end of outgoing MCBs grouted/ flush to wall, complete all as specified by Engineer-in-charge. (Note :- MCCB will be measured and paid under seperate item) (i) Cost of Eye/bottle thimbles used for connection MCBs in DBs shall deemed to be included in unit rate quoted for this items, (ii) Electric wiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth. (iii) connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped. all the vacant holes of the DB shall be provided with blank plates of appropriate size complete all as specified and directed by Engr-in-charge.

S & F MCCB, 4 Pole, 100 A, 25 KA for fixing in DB including proper thimble connection, thermal and magnetic release protection complete all as specified and directed by Engineer-in-charge.

S & F MCCB, 4 Pole, 63 A, 16 KA for fixing in DB including proper thimble connection, thermal and magnetic release protection complete all as specified and directed by Engineer-in-charge.

S & F in replacement of Sheet metal enclosure DB TPN 4 ways double door 415 volts with 200 Amps standard bus bar of suitable size and common neutral link flush mounting type, drilling holes for incoming and out going cables complete with IP-43 protection complete all as specified and directed by Engr-in-charge

S & F in replacement of MCB, TRIPLE pole & neutral (TPN) 10 KA 240 volts 63 Amp capacity fixing in DB’s complete all as specified and directed. (Note: MCB should be B curve as directed by engineer in charge)

Supply and fixing in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed by Engineer-in-charge.

M & L for Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 4 Sqmm Copper conductor Earth wire shall be measured as one unit) Note 2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring is included in quoted rates.

M & L for Sub main wiring with two single core 2.5 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 2.5 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 2.50 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 2.5 Sqmm Copper conductor Earth wire shall be measured as one unit) Note 2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring is included in quoted rates.

M & L for Sub main wiring with two single core 1.5 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit of suitable dia including 1.5 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 2.50 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 1.5 Sqmm Copper conductor Earth wire shall be measured as one unit) Note 2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring is included in quoted rates.

Supply & fix Sheet metal enclosure suitable for fixing DB and Electric meter, factory made of size 60 x 60 x 18 cm made out of 1.6 mm thick MS sheet with double door, sutiable locking arrangements, powder coated, cutting chasing in wall and fixing and making good as per existing surface complete including removing old one, complete all as specified and directed by Engr-in-charge.

Supply and fix incl taking down Led Stellar Square/round recessed Mounted slim and and Elegant Downlight /Panel for indoor application with high aesthetic appeal of capacity 12 watt, minimum 100 lumen/watt having correleted color temperature(CCR) of Emitting light 6500 OR 3000 K(According to requirement) with CRI of LED >90.complete with all electrical connection up with PVC insulated twin core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix new generation, energy saving, environment friendly, long life aesthetically designed aluminium landscape IP 65 luminaire for diffused lighting with high power LED as light source LED Bollard pathway lights of capacity 10 watt cool/warm white made up of aluminium pipe UV protected pure polyester powder coated having colour temperature(CCT) 3000K warm white fixed to concrete foundation by means of 3 nos M10 bolts complete all as specified and directed by Engr-in-charge. Note:- Cost of PCC foundation of suitable height , PVC conduit 25 mm of suitable length, all electrical connection and all other items whichever required for fixing is deemed to be included in the unit rate quoted for this item.

Supply and fix incl taking down LED garden light fitting cool/warm white with LED bulb upto 20 watt E27/B22 base cap fitted on the piller with the help of GI pipe of suitable length and PCC of suitable height nut bolts and in stainless steel housing with clear acrylic cover in top section with IP 65 protection class ,connection with 1.5 sqmm 3 core copper cable including making suitable PCC foundation and all electrical connection complete all as directed as per sample approved by Engr-in-charge.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections one twin core cable flat or circular stranded conductor size of 6 Sqmm, twin core complete all as specified.

Supply and fix in replacement of LED post top fitting 40 W powder coated aluminium die cast and spun aluminium with clear/diffused PC cover suitable for landscape lighting 240V, 50 Hz ,AC supply complete with all accessories internally pre wired including provision of 3 core PVC flexible copper conductor from electric supply source to connector of light with degree of protection IP 65,CCT 6500K complete all as specified and directed by Engr-in-charge. Note: Cost of GI pipe of suitable dia & suitable length, grouting holes into piller and cement work has been included in the rate quoted by contractor

Supply and fix in replacement of LED post top fitting 20 W powder coated aluminium die cast and spun aluminium with clear/diffused PC cover suitable for landscape lighting 240V, 50 Hz ,AC supply complete with all accessories internally pre wired including provision of 3 core PVC flexible copper conductor from electric supply source to connector of light with degree of protection IP 65,CCT 6500K complete all as specified and directed by Engr-in-charge. Note: Cost of GI pipe of suitable dia & suitable length grouting holes into piller and cement work has been included in the rate quoted by contractor

S & F INDUSTRIAL HIGH BAY LED light of capacity 120 W ,The LED make must be of minimum 100 lumen/watt .The driver must be power factor > 0.95 with short circuit protection , open circuit protection , reverse polarity protection , high voltage protection. the luminaire must have secondary optics with perfectly matched lens for better light control with CMRI approved correleted color temperature(CCT) of Emitting light 5700 K with with die cast aluminium housing with heat resistant toughened glass IP 66 protection comlete with control gear box and all accessories require to fix the light on wall/structure/pole like clamps nus, bolts et cwith suitable size and including connecting up with twin core twisted flexible copper conductor cable 1.5x2 sqmm with proper clamps. complete all as specified and directed by Engr in Charge.

S & F INDUSTRIAL HIGH BAY LED light of capacity 80 W ,The LED make must be of minimum 100 lumen/ watt .The driver must be power factor > 0.95 with short circuit protection , open circuit protection, reverse polarity protection, high voltage protection. the luminaire must have secondary optics with perfectly matched lens for better light control with CMRI approved correleted color temperature (CCT) of Emitting light 5700 K with with die cast aluminium housing with heat resistant toughened glass IP 66 protection comlete with control gear box and all accessories require to fix the light on wall/structure/pole like clamps nus, bolts et cwith suitable size and including connecting up with twin core twisted flexible copper conductor cable 1.5x2 sqmm with proper clamps. complete all as specified and directed by Engr in Charge.

Supply and fix incl taking down new generation energy saving 9/10 watt LED bulk head (porch light fitting) made of plasitic housing with opal diffuser With IP 65. having correleted color temperature(CCR) of Emmiting light 6500/3000 K with CRI of LED >90. connection with PVC insulated twin core flexible copper conductor cable of suitable size.complete all as specified and directed.

Supply and fix in replacement of old unsv building light ,25 W IP 66 LED security light for building luminaire comprising of die cast aluminium housing with weather proof gasket for lamp & driver compartment with system wattage of 25 W . The LED make must be of minimum 100 lumen/watt CCT 6500K .The driver must be power factor > 0.95 with short circuit protection , open circuit protection , reverse polarity protection , high voltage protection. the luminaire must have secondary optics with perfectly matched lens for better light control with GI bracket of suitable size and clamps with fixing accessories connection with PVC insulated three core flexible copper conductor cable 0.75X3 Sqmm with proper clamps .complete all as specified and directed.

Supply and fix surface mounted LED luminaire 36 watt cool white 3600-6500 suitable for gridd surface mounted imensions: 2x2 Ft. incl connecting with twin core copper wire from ceiling rose to fitting, Fixture size: (LxWxH) in (595x595x65) mm incl lamp and driver all as specified & directed.

Supply and fix recess mounted LED luminaire 36 watt warm white 3000 K suitable for gridd celling cutout dimensions: 2x2 Ft. incl connecting with twin core copper wire from ceiling rose to fitting, Fixture size: (LxWxH) in (595x595x65) mm incl lamp and driver all as specified & directed.

Taking down existing LT panel board (Meter Box) located at Map block and supply and fixing sheet metal enclosure board made of 1.6 mm thick metal sheet and painting 2 coats with synthetic enamel paint over a coat of red oxide primer including Aluminium bus bar 200 amp and fixed with wall for fixing MCCB 4P 125 amp and electric meters complete with wiring, fitting and accessories, locking arrangements with handle (adequate size and adequate depth for the following equipments, internal wiring and termination of external cable, lugs and glands and conduits as required) comprising of following. (a) Incoming 125 Amp 4 pole MCCB 25 KA-01 Nos.(Main incomer) (b) Aluminium Bus bar rated 200 Amp capcity. (d) 10Amp DP/SPN MCB-01 No (Outgoing for stair case and garrage) (c ) 63 Amp DP/SPN MCB-06 Nos (Outgoing for Qtr meters) (e) Taking down and Refixing of electric meter energy meters single phase 240Volt 40Amps 50HZ -06 Nos.

Supply and fix in replacement of highly reliable energy efficient multi high power LED with lens flood light designed with optimized optical performance and good heat dissipation with uniform distribution of capacity 100 Watt, CCT 5700-6500K, CRI>70, rated voltage 220V-240V AC, 50 Hz, Power factor>0.9, IP-66 dimension 290x235x155 mm epoxy powder coated pressure die casted aluminium housing with bright anodised aluminium reflectro and enclosed with heat resistant and toughened glass having constant current driver suitable for 140-280V AC working range suitable for facade lighting with all accessories internally pre wired including connecting with flexible copper conductor to connector of the light with necessary fixing arrangements complete all as specified and directed by Engr-in-charge.

Supply and fix incl taking down Led Stellar Square/round surface Mounted slim and and Elegant Downlight /Panel for indoor application with high aesthetic appeal of capacity 20 watt, minimum 100 lumen/watt having correleted color temperature(CCR) of Emitting light 6500 OR 3000 K(According to requirement) with CRI of LED >90.complete with all electrical connection up with PVC insulated twin core flexible copper conductor cable of suitable sizecomplete all as specified and directed.

Supply and fix incl taking down Led Stellar Square/round surface Mounted slim and and Elegant Downlight /Panel for indoor application with high aesthetic appeal of capacity 10 watt, minimum 100 lumen/watt having correleted color temperature(CCR) of Emitting light 6500 OR 3000 K(According to requirement) with CRI of LED >90.complete with all electrical connection up with PVC insulated twin core flexible copper conductor cable of suitable sizecomplete all as specified and directed.

S&F batten LED 22 watt inveter LED tube light complete fitting 230 volt energy saving, 04 hrs battery backup, CRI ≥80 more than, driver efficiency ≥ 85%, operating voltage 230 volt, 50hz operating temp (-10°C to 50°C) complete accessories internally pre wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by engineer-in-charge. .

S & F LED lamp invertor technology 9 watt with 4 hour power back up with efficiency more than 100 lumen per watt, Lithium ion battery including removing of unserviceable lamp complete all as specified and directed by Engr-in-charge.

S & F Solar LED post top luminaire 20 watt of high efficiency poly crystalline Solar Module with maintenance free Lithium battery of having 3 days backup with 2 PIR Sensor with 360 degree coverage , 5700K, IP-65 made of pressure die cast aluminium housing & clear glass complete with all accessories internally prewired wire including electronic driver, connecting with fitting and including disconnecting and taking down existing unsv light fitting complete all as specified and directed by Engr-in-charge.

S & F modern energy efficient Track light of capacity 20 watt 220-240 volt, Colour (Black), material (Aluminium), dimensions(mm) 158x65x125, lamp base (LED), CCT 3000K, Lumen 1500 lm,controller type (push button), power source ( electric) incl electrically connection , including removing of unserviceable track light fittings of any description complete all as specified and directed by Engr-in-charge. Make: Philips model No 31446 or as equivalent in crompton /C&S./Havells/Indo-asian.

S & F well designed modern energy garden spike light of capacity 12 watt 220-240 volt, Colour (Anthracite), material (Aluminium), dimensions(mm) 100x75x75, lamp base (LED COB Integrated), CCT 4000K, Lumen 360 lm, IP 65 protection against dust & jet of water from any direction ,controller type (push button), power source (corded electric) incl electrically connection complete all as specified and directed by Engr-in-charge. Make: Philips model No 31385 or as equivalent in crompton /C&S./Havells/Indo-asian.

Labour only for removing/refixing AMA LED Elevated Heliport Light and checking serviceability of AMA LED Elevated Heliport Light ,Isolation Transformer and Primary/Secondry connectors with the help of suitable equipment and reassemble the same after replacement of unserviceable componnent and testing complete all as directed at site by Engr-in-Charge. Note:- Unserviceable components like Isolation transformer,LED Light,Primary connector and Secondry connector will be measured and paid separatly under below mention schedule

Material & labour for Isolation Transformer 45 Watt, 50 Hz, 5000V grade primery/secondry 6.6 A/6.6A all as specified and directed by Engr-In-Charge Make:- India Isolation Transformer or Equivalent in Crompton Greaves/Alstom/Kotsons.

Material & labour for LED Elevated Heliport Light all as per existing installed at helipad make of AMA INDIA complete all as specified and directed by Engr-In-Charge Note:- Prior to placing order for supplyof heliport lights colour of the light will be approved from AO/Engr-in-Charge Make:- AMA India(As per existing only) or as approved by GE.

Material and labour for Primary Connector for connection of LED Helipad Light with transformer complete all as specified and directed.

Material and labour for Secondry Connector for connection of LED Helipad Light with transformer complete all as specified and directed.

Periodical inspection by qualified team for LED Elevated Heliport Light system complete installed at Patiala cantt incl repair/ replacement of unserviceable/ defective accesories if any and as mentioned below: 1. CCR Panel 8 kVA, Make: NASU systems year of installation 2018 2. Underground cable 16 SQMM PVC sheathed stranded copper conductor single core airport light cable of 5 KV grade: Approx 2400 RM 3. CI housing boxes and LED Elevated Heliport Lights with connected componnents like Isolation transformer,LED Light, Primary connector and Secondry connector: 54 Nos Note 1 : Contractor should inspect the system once in two months or as called upon by Engineer- in -charge. The inspection and repair should incl complete testing of system, rectification of faults occured due to moisture etc incl taping of joints minor repair of the CCR panel. Accesories/materials for insulation and water proofing incl tapes, water proofing compound are deemed to be incl in this item. If any Major repair is required the same is to be informed by the contractor alongwith cost to be occured. Unserviceable components like Isolation transformer,LED Light,Primary connector and Secondry connector will be measured and paid separatly. Note 2 : Contractor is advised to visit the complete site prior bidding. Contractor should visit the site upon notification within 24 hrs. Any delay thereafter shall results in penalty of Rs 500/ day.

Supply and fix in replacement of recessed accentSpot COB downlight of capacity 30 watt aluminium die cast housing & heat sink for durable performance, long life with 30,000 burning hours , Lumen- 2250lm, cut out 120 mm , CRI> 80, PF>0.9, Beam angle 36 degree, height 81 mm, Dia 135 mm having surge protection 2 kv incl electrically connection complete all as specified and directed by Engr-in-charge. Make: Philips (SKU: LT01329-1) or as equivalent.

Supply and fix Modular switch in repair 1 way, 6 Amps, 1 module, 230 volts make and fitment as per gound requirement complete all as specified.NOTE-contractor shall visit the site to check make and size of item.

Supply and fix Modular switch in repair 1 way, 16 Amps, 1 module, 230 volts complete all as specified. NOTE-contractor shall visit the site to check make and size of item.

Supply and fix Modular socket in repair 5 pin 6 Amps, 2 module 230 volts complete all as specified. NOTE-contractor shall visit the site to check make and size of item.

Supply and fix Modular socket in repair 5 pin 6 &16 Amps, combination type 2 module complete all as specified. NOTE-contractor shall visit the site to check make and size of item.

Supply and fix in replacement of metal flush box of 2 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of metal flush box of 3 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of metal flush box of 6 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of metal flush box of 8 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of modular cover plate of 2 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of modular cover plate of 3 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of modular cover plate of 6 module in MAP qtrs complete all as specified and directed.

Supply and fix in replacement of modular cover plate of 8 module in MAP qtrs complete all as specified and directed.

Supply and fixing 36W , 2’X2’ recessed Luminaire with housing made up of CRCA powder coated made up of High transmittance diffuser for glare free symmetric light distribution., Powered by Isolated, SELV output Electronic Driver with Output Short-circuit protection, Surge Voltage protection and other safety & performance test as per IS:15885 Part 2/Sec 13. Power Consumption should not greater than 36W and System Efficacy not less than 100 Lumens/Watt, CCT 5700K PF>0.95, CRI>80 ,THD<10%. Operating temperature: -10 °C to +35 °C , Operating voltage range: 140 V - 270 V. Built in PIR Sensor. Luminaire Should conform to IP20 Classification. Test report to be submitted; photo biological safety norms: IS16108, test certificate to be submitted; certification: LM 79 for luminaire and LM80 for led source, Driver and Fixture to be BIS certified as in repair complete all as specified and as directed by the Engr-in-charge.

Taking down carefully existing points wiring on surface conduit/concealed conduit for light/ fan/socket /power/ bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires,gutties, conduit, wooden boards etc and making good the disturbed portion of walls, ceiling etc all as specified and directed Engr-in-charge.

M & L for Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan in PVC conduit to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor connected to cmmon earth dolly controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed by Engineer iin-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost of modular cover plate and metal flush boxes is deemed to be included in the unit rate quoted for this item). Note -IV - cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item.

All as per Sl item No 60.00 above herein before but one socket out let 5 pins 5 Amp on the same board with other switches complete all as specified and directed.

All as per Sl item No 60.00 above herein before but for one socket out let 5 pins 5 Amp on independent board complete all as specified and directed.

All as per item No 60.00 herein before but 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLSH single core muilti-stranded copper earth wire for switch socket combination 3 pin 15 amps on independent board.

Supply and fix in replacement of Modular switch 1 way, 6 Amps, 1 module complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of Modular switch 1 way, 16 Amps, 1 module complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of Modular socket 5 pin 6 Amps, 2 module complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of Modular socket 5 pin 6/16 Amps, combination type 2 module complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of Fan regulator modular type 2 module complete all as specified and directed by Engr-in-charge.

Supply and fix Ceiling rose surface bakelite surface 65 x 50mm 3 terminals all as specified & directed by Engr-in-charge.

Supply and fix Lamp holder including LED bulb 9 W including flexible wire 0.5 Sqmm copper cable all as specified & directed by Engr-in-charge.

Supply and fixing of inverter LED security light luminaire 30 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDs having optical grade polycarbonate lens with 4 hours battery back up all accessories internally pre wired and including connecting up with two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light with GI bracket of suitable size and clamps with fixing accessories including disconnecting and taking down old unserviceable security light fitting of any description and in any position complete all as specified and directed. Make: Halonix cat ref no LED SL 30W HLSLD-ML04-30-CWL-INV-RTC-R or equivalent in Havells/Crompton/Bajaj.

Supply and fixing LED batten fitting 18-20 watt, 4 feet, PVC housing with electronic driver cool/warm type complete connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED batten fitting 10-12 watt, 2 feet, PVC housing with electronic driver, including LED luminaire 10/12 watt cool/warm type connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed by the Engineer-in-Charge.

AGGARWAL & CO (BID ID -3345694)

Mohinder Pal and Sons (BID ID -3345026)

The Rahul Vig (BID ID -3354983)

SWAMI ENGINEERS (BID ID -3345128)

Jawandha Enterprises (BID ID -3347417)