Extension of Radiology unit

Amount

CIVIL & SANITARY WORKS

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass door latch with necessary screws etc. complete :

Providing and fixing bright finished brass handles with screws etc. complete:

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :

125x85x5.5 mm (heavy type)

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 600 x 600 mm

Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 mm

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

0.80 mm thick with zinc coating not less than 275 gm/m²

Extra for circular cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter:

0.80 mm thick

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.

0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws

Ridges plain (500 - 600mm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of

12.5 mm thick tapered edge gypsum moisture resistant board

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

CEMENT PLASTER (IN COARSE SAND

12 mm cement plaster of mix :

1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:4 (1 cement: 4 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Providing and fixing aluminium work for doors , window , ventillators and partitions with extrude built up standard tubular sections / appropriate Z sections and other sections of approved make confirming to IS:733 and IS: 1285 ,fixing with dash fastners of required dia and size , including necessary filling up the gaps at junction , i.e. at top , bottom and sides with required EPDM rubber / neoprene gasketetc .Aluminium sections shall be smooth rust free , straight , miltred and jointed mechanically wherever required including cleat angle ,Aluminium snap beading for glazing / panelling ,c.p brass / stainless steel screws ,all complete as per architectural drawings and the directions of Engineer -in-charge .(glazing panelling and dash fastners to be paid for separately) :

for fixed portion

Powder Coated aluminium (minimum thickness of powder coating 50 micron )

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing brass bib cock of approved quality :

20 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design 15mm

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing toilet paper holder :

Vitreous china

Providing and fixing SOAP DISPENSER WITH GLASS BOTTLE, Model No- -AKPCHR- 35735P of M/S Jaquar or equivalent make

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing in position CP twin robe hook with CP brass screws etc complete. CP Brass Double Coat Hook of Jaquar make (AKP 35761P) or equivalent make

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

32 mm dia

Supplying & fixing box shape stainless steel heavy type grating 125 to 150 mm for traps etc. all complete as directed byengineer..

Providing and fixing Polyvinyl Chloride (PVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Rate is inclusive of concealed work, including cutting chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

100 mm nominal dia Pipes

Providing , fitting flush door shutters made of 35 mm Block Board Shutter & finished with Decorative Laminate Sheet fitted with all fitting hinge,handle,Mortise Lock etc. including 100X8 mm wide beading on one side of wall along door frame with WPC doard finished with Decorative Laminate Sheet fitted with all fittings complete in all respect as specified and directed by the Department.

Providing & fixing in position 6mm thick Mirror machine edge polished in required profile with 12mm thk marine ply backing and fixed with S.S. D-brackets / studs / teak wood beading. The work is to be completed in all respects as per instruction and approval of EIC / Architect.

Joint filler

4 inch width & 1ft depth

CARPANTRY WORKS

600mm Wide Granite Platform with Sink & Cock

Providing and constructing Granite Pantry platform by using 18 mm thick gang saw cut mirror polished granite stone at top to be laid on 600 mm wide-750 mm high storage made of 18 mm thk. marine grade plywood (IS 710). All exposed edges of the granite are to be rounded and polished. 150mm high granite slab is to be provided for splash back. The exposed surface and edges of granite are to be polished. All joints of granite are to be filled with epoxy filler. Vertical support and the understructure below platform is to be made of 18/19mm thick marine grade plywood (IS 710) finished with 0.80mm thk balancing plain white/ ivory/ grey colour laminate for all inside surfaces. One intermediate shelf made out of 18/19 mm thick marine grade plywood (IS 710) finished with 0.80mm thk balancing plain white/ ivory/ grey colour laminate on both sidesand fixed on SS buttons is to be provided. All the inside surfaces of the shutters made of 18/19 mm thick marine grade plywood are to be finished with 0.80mm thk balancing plain white/ ivory/ grey colour laminate

Rate to include making opening for Sink and pillar tap with all exposed edges polished, front shutters made out of 18/19mm thk.marine grade plywood (IS 710). All inside surfaces are to be finished with 0.80mm thk balancing plain white/ ivory/ grey colour laminate and exposed surfaces to be finished with 1.0mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503, in approved pattern and style. All joints shall be made water tight in perfect line, level & slope as desired including curing, polishing & cleaning all joints and floating in coloured cement mortar. (Only front length will be measured. Wastage due to dimensional difference, pattern, cutting sizes available will be to the contractors account).

Rate to include making of all holes & openings required for fixtures and fittings such as hinges, ball catchers, tower bolts, SS handles, 40mm thick granite edge (double nosing) with chamfering on top etc. complete. The entire item is to be completed in all respects with drawers, shutters etc.,as per drawing and instructions from EIC / Architect.

Note: Rate should include Nirali make, popular range, Grace plain with flat border SS Sink of size 610mm x510mm bowl depth 200 mm , Anti scratch, Glossy finish.

LOOSE FURNITURE

Cabin Table with side cadenza

Providing & fixing in position table of size 1200mm X 600mm as per approved design & shape given in the detailed drawing consisting of:

The Table top made out of 18 mm thk. marine grade plywood (IS 710) - top and sides finished with 1.0mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503 in all outside surface. All exposed side edges of Ply/ board shall be covered with teak wood beading finished with matching Deco paint to give it similar finish. The bottom surface of the table top alongwith all other inner surfaces of the table should be finished with 0.80mm thk balancing laminate of white/ ivory or grey colour.

Pedestal unit of size 450mm X 600mm made out of 18 mm thk. marine grade plywood (IS 710) for top, sides, bottom and back finished with 1.0mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503 and all exposed side edges of Ply/ board shall be covered with teak wood beading finished with matching mellamine polish to give it similar finish. Pedestal unit consisting of 3 nos drawer unit and 1 shutter. Drawer - front made out of 18 mm thk. marine grade plywood (IS 710) , sides & back made out of 12mm marine grade plywood (IS 710) and bottom made out of 18mm marine grade plywood (IS 710). All external surfaces finished with Laminate and internal surfaces finished with .8mm White Colour Laminate (including bottom & sides of the drawers). Shutter made out of 18mm thk marine grade plywood (IS 710) finished externally with 1mm Laminate and internally with .8mm thick laminate.

Footrest: made of 18mm thk marine grade plywood (IS 710) as per detail drawing. Footrest finished with Laminate and wooden moulding.

Second Class teak wood lippings to be provided on all exposed plywood edge surfaces and be finished with white Deco Paint. Unless otherwise specified on the drawing, the thickness of teak wood lipping will be 6mm (min).Except table top

Item is to be completed as per the drawing and direction EIC/Architect

Rate shall include cost of all hardwares of approved make as mentioned below:

OZONE Make: Multi purpose Lock for Drawers & cabinet shutters, 22mm Rim Lock with 2keys. Nickel Plated

OZONE Make: Furniture Handle, Size 183mmx24mmx128mm, Finish SS Matt.

Keyboard-EBCO make Key board tray with soft palm with mouse tray

Wire manager - 1 No.

DESK & DRAWERS

CLERICAL TABLE( 2'-3" X 4'-0: X 2'-6")

Providing & fixing in position table of size 1200mm X 600mm as per approved design & shape given in the detailed drawing consisting of:

The Table top made out of 18 mm thk. marine grade plywood (IS 710) - top and sides finished with 1.0mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503 in all outside surface. All exposed side edges of Ply/ board shall be covered with teak wood beading finished with matching Deco paint to give it similar finish. The bottom surface of the table top alongwith all other inner surfaces of the table should be finished with 0.80mm thk balancing laminate of white/ ivory or grey colour.

Pedestal unit of size 450mm X 600mm made out of 18 mm thk. marine grade plywood (IS 710) for top, sides, bottom and back finished with 1.0mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503 and all exposed side edges of Ply/ board shall be covered with teak wood beading finished with matching mellamine polish to give it similar finish. Pedestal unit consisting of 3 nos drawer unit and 1 shutter. Drawer - front made out of 18 mm thk. marine grade plywood (IS 710) , sides & back made out of 12mm marine grade plywood (IS 710) and bottom made out of 18mm marine grade plywood (IS 710). All external surfaces finished with Laminate and internal surfaces finished with .8mm White Colour Laminate (including bottom & sides of the drawers). Shutter made out of 18mm thk marine grade plywood (IS 710) finished externally with 1mm Laminate and internally with .8mm thick laminate.

Footrest: made of 18mm thk marine grade plywood (IS 710) as per detail drawing. Footrest finished with Laminate and wooden moulding.

Second Class teak wood lippings to be provided on all exposed plywood edge surfaces and be finished with white Deco Paint. Unless otherwise specified on the drawing, the thickness of teak wood lipping will be 6mm (min).Except table top

Item is to be completed as per the drawing and direction EIC/Architect

Rate shall include cost of all hardwares of approved make as mentioned below:

OZONE Make: Multi purpose Lock for Drawers & cabinet shutters, 22mm Rim Lock with 2keys. Nickel Plated

OZONE Make: Furniture Handle, Size 183mmx24mmx128mm, Finish SS Matt.

Keyboard-EBCO make Key board tray with soft palm with mouse tray

Wire manager - 1 No.

600mm Wide Running Counter Table with Pedestal

Providing and laying wall mounted Running Table with Key board , Metal CPU Trolley, Footrest and free standing pedestal at every 1200mm length for over all size of top as mentioned bellow. It shall consist of 18/19mm thk marine grade plywood (IS 710) Ply top as per design (double edge on the front with 25mm thk half round moulding on the edges) supported on 18/19mm thk marine grade plywood (US 710) verticals at every 1200mm length. Suitable (as per Architects design) wooden moulding with melamine shall be provided to the edge of the top. The top of the counter alongwith all other external surfaces should be finished with 1mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503, in approved pattern and style.

1no. Computer key board tray (either ready made / made to the order as per architects design using 19mm thk Marine ply base and 24x50mm round edged moulding on the front fixed with telescopic/double(Hafele/ebco/ Hettich make) approved sliders)

Each top shall be provided with a pedestal (set of three drawers with central locking system either movable or fixed to the table) , made with 18/19 mm thk marine grade ply wood. The Facia and all other outer surfaces of drawer unit shall be finished with 1mm thk Century Laminate Strauss Walnut 93414 & Degas Walnut 4503, in approved pattern and style and all inner surfaces should be finished with 0.80 mm thk balancing laminate in White/ Ivory or Grey colour shade. . The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank.

WALL HUNG STORAGE (450MM HIGH X 300MM DEEP)

P/F wall hung storage made out of 19 mm thk BWP Ply 300 mm deep, 6mm thk BWP Grade Ply for the back, 19mm thk.BWP Grade Ply, openable shutters with hinges as recommended & with 1.0 mm thick Century Laminate Strauss Walnut 93414 & Degas Walnut 4503 on all exposed surface, in approved pattern. It shall also consist of 19mm. removable shelves finished with 0.80mm thk balancing laminate of white/ ivory or grey colour on both sides. All edges shall be provided with leaping patties on all sides, at 40 cm spacing. Rate shall be inclusive of all hardware fittings and fixtures like hinges, tower bolts, S.S Brush finish handles , ball-catches shall be of brass heavy duty all Complete with approved make Locks handles etc. complete as per design / instructions.

LOW HT. STORAGES (1'-6" DEPTH X 2'-6" HT.) (BACK CREDENZA)

Providing and laying low ht. Storage units of sizes as mentioned above. They shall consist of 18/19 mm thk. BWP. Plywood top and sides , and base, 6mm thk. Marine ply back, 19mm thk. BWP. Ply shutter with self closing higes of hafele make(full ovel open) & PVC lipping matching with approved laminate/Veneer on all the edges. All external surfaces to be finished in 1.0 mm thick Century Laminate Strauss Walnut 93414 & Degas Walnut 4503

Division of shutters shall be made equally according to the length of the storage. A 19mm thk. Fixed BWP. Ply shelf on battens shall be provided at 400mm intervals from the base.

Suitable wooden moulding (as per Architects design) with mellamine shall be provided to the edge of the storage top. All inner surfaces including shutters shall be finished with 0.80mm thk laminate of approved shade and colour

Rate shall be inclusive of all necessary approved fittings like hinges(Hafele make), locks(Godrej make/Vijayan), 75mm long brushed finish handles(kich -neki make-CHR103),tower bolts and any miscellaneous hardware items.

ROLLER BLINDS, VERTICAL BLINDS, FILM etc.

ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required..

Group-A Upto 3 mtr

Group B- Upto 4 mtr.

Group B- Upto 5 mtr.

Wiring for Group COntrolled (Looped) light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required..

Group-A Upto 3 mtr (2 points' Loop)

Group B- Upto 4 mtr.(2 points' loop)

Group C- Upto 5 mtr.(2 points' loop)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit conduit along with accessories in surface/ recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.

5/6 A switch

25A Single Phase DOL Starter for AC Units

3 pin 5/6 A socket outlet

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75x75mm)

3 Module (100mmX75mm)

4 Module (125x75mm)

6 Module (200mmX75mm)

8 Module (125mm x125mm)

12 Module (200mmx150mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. For Individual 6A Raw power points

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing3 Nos. of 3 pin 5/6 A modular socket outlet and one No. of 15/16 A modular switch, 1 No. of LAN socket with connections etc. as required.(For Workstations )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. For Individual 16A Raw power points

Supply of light fixtures/ Fittings as per the details given below including necessary hardware such as clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position as required

Slim Ceiling/ surface mounted 24 W LED panel Light fitting having Minimum lumen output 4000 lumen; dimension in Length: 190 mm, Width: 190 mm & Height: 28 mm with premium diffuser complete with all surface module accessories

Recess-mounted round downlight with die cast aluminium make having Item Code- LARP01R018XN 18 W. With cutout: Dia 152 mm. Overall diemnsions- dia 171 x 128 mm or equivalent as approved bt the EIC/architect.Recess- mounted, maintenance-free, round downlight with die cast aluminium housing and sleek backlit design suitable for low height ceiling, of jaquar make, having Item Code- LARP01R018XN 18 W, having overall dia 171mm and height 28mm

Supply, Installation, testing and commissioning of Led fixture Surface Mounted 4 Feet with Polycarbonate diffuser with aluminium housing having following technical specifications with all accessories including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable i/c hanging arrangement with chain and wiring with GI flexible conduit with coupler where ever if required and earthing as required.. (i) Minimum lumen output 4000 lumen (ii) System lumen efficacy ≥ 110 Im/Watt (iii) CCT ≥ 5700, CRI > 80, PF≥ 0.95, THD < 10%, IP 40 (iv) L 70 rated life of 50 K hours (v) in built surge protection device of minimum 2.5 KV.

600 MM TUBE LIGHT- LED batten tubes, Glaze LED Batten, High quality aluminium extruded with decorative end caps, Wattage-10W, CCT- 4000 K, of Phillips, Havells, Bajaj, Wipro or equilivent as approved by the Engineer- incharge/ Architect. [FL]

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying, Installation, Testing and Commissioning of single phase 300mm Sweep, 900/1400 RPM heavy duty propeller type exhaust fan for operation on 220-240 V, 50Hz, AC electricity, in the existing opening including making good the damages and connection with 1.5 sqmm FRLS PVC insulated copper wire including louver shutter complete as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying, laying and termination of 4 pair Copper solid, twisted pair G600 CAT--6 cables through specified dia MS conduits / raceways. Cables must meet and exceed category 6/ class E standards requirements in ISO/IEC11801, CENELEC EN50173 & TIA 568-B2-1. and providing & terminating with RJ-45 (Krone make) with face plates / I/O Ports in suitable modular / MS box from server / EPABX room to individual work stations and terminating other end with RJ-45 connector including numbering with ferule. Note- Rates shall be all inclusive as mentioned in the description above and the payment for the same item shall be made on the number of points provided based on the above description. Rates shall be inclusive of 5'-0" long patch chord with crimping on both ends

2 Run of Cable

I/O Box

Supply and Installation of CISCO 9000 Series 48 Port Network Switch

Supply of Computers

Supplying and fixing following way, horizontal type Triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

4 Way (4+12) Double Door

Supplying and fixing following way, horizontal type Single pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 Way, Double Door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, double pole isolatorin the existing DB complete with conectons

Supplying and fixing following rating,four pole pole, (Three phase and neutral), 415 volts, Isolator/ MCB, in the existing MCB DB complete with connections, testing and commissioning etc. as required.

4 pole MCCB, 125A, 36KA

Supply and Installation of 6KVA UPS including batteries ,Make:Reallo,Vertiv,Delta

Supplying with installation testing and commissioning of 2 STAR rating non ducted cassette A.C type,Inverter, air conditioner of the following capacity with cordless remote with 1year warranty of A.C and Compressor.(Make:Bluestar/Voltas/Daikin/Carrier)

Capacity:3Ton

Material of Evaporator-Copper

Material of Condenser-Copper

Supplying with installation testing and commissioning of 3 STAR rating non ducted split A.C type,Inverter, air conditioner of the following capacity with cordless remote with 1year warranty of A.C and Compressor.(Make:Bluestar/Voltas/Daikin/Carrier)

capacity:1.5 Ton

Material of Evaporator-Copper

Material of Condenser-Copper

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt.

50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and Installation of Copper Pipeline for Installation of A.C,Size:5/8,3/4.

Supply and Installation of Copper Pipeline for Installation of A.C,Size:1/4,1/2.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Dismantling work as directed by Architect/ Site-Incharge

UCN CONSTRUCTION COMPANY PRIVATE LIMITED

VERSHA TECHNOTRADE PVT LTD