Construction of Girls Common Room at Govt. Degree College at Billawar.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables, etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5m including getting out excavated earth as directed by Engineer-in-charge, including all leads and lift. a) All Kind of soil

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:4:8 (1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size) (including all leads and lifts carriages of material by MT/ HL)

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:a) 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size). (including all leads and lifts carriages of material by MT/ HL)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centring ,shuttering, finishing and reinforcement. All work upto plinth level with: a) 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size). (including all leads and lifts carriages of material by MT/ HL)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttreses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centring shuttering, finishing and reinforcement. a) 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size). (including all leads and lifts carriages of material by MT/ HL)

Brick work with common burnt clay F.P.S. (non modular) cement mortar 1:4 (1 cement:4 fine sand) bricks of class designation 75 in foundation and plinth in (including all leads and lifts carriages of material by MT/ HL)

Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand:4 graded stone agg. 12.5mm nominal size and curing complete (including all leads and lifts carriages of material by MT/ HL)

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square meter on damp proof courses after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:6 (1 cement:6 coarse sand) (including all leads and lifts carriages of material by MT/ HL)

Extra for brick work with common burnt clay bricks / cement concrete bricks in superstructure above plinth level upto floor five level.

Half brick masonry with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:4 (1 cement:4 coarse sand) (including all leads and lifts carriages of material by MT/ HL)

Extra for half brick masonry in superstructure above plinth level upto floor V level.

Reinforced cement concrete work in beams, suspended floor, roofs having slope upto 15˚, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with: a) 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/ HL)

Steel Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. a) Cold twisted bars.

Centring and shuttering including strutting, propping etc.and removal of form work for :

a) Foundation, footings, bases of columns etc. for mass concrete.

b) Suspended floors, roofs, landings, balconies and access platforms.

c) Lintel, beams, plinth beams, girders, bressumers and cantilevers.

d) Edges of slabs and breaks in floors and walls under 20cm wide.

e) Columns, Pillars, Piers, Abutments, Posts and struts.

h) Weather shade, Chajjas, corbels etc. including edges.

Filling available earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.50 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete (including all leads and lifts carriages of material by MT/ HL)

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:5:10 (1 cement:5 coarse sand:10 graded stone aggregate 40mm nominal size) (including all leads and lifts carriages of material by MT/ HL)

6mm cement plaster to ceiling of mix. 1:3 (1 cement:3 fine sand) (including all leads and lifts carriages of material by MT/ HL)

15mm cement plaster on the rough side of single or half brick wall of mix. 1:6 (1 cement: 6 fine sand) (including all leads and lifts carriages of material by MT/ HL)

12mm cement plaster of mix. 1:6 (1 cement:6 fine sand) (including all leads and lifts carriages of material by MT/ HL).

15mm cement plaster on the rough side of single or half brick wall of mix. 1:4 (1 cement: 4 fine sand) (including all leads and lifts carriages of material by MT/ HL)

12mm cement plaster of mix. 1:4 (1 cement:4 fine sand) (including all leads and lifts carriages of material by MT/ HL)

15mm cement plaster on the rough side of single or half brick wall finished with a floating coat of neat cement of mix. 1:3 (1 cement:3 fine sand) (including all leads and lifts carriages of material by MT/ HL)

18mm cement plaster in two coats under layer 12mm thick with cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement:6 fine sand (including all leads and lifts carriages of material by MT/ HL)

Add for plaster drip course / grooves in plastered surface or moulding to RCC projections.

Providing and laying vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand and manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, in a average 6mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). a) Size of tile 600x600 mm.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete (including all leads and lifts carriages of material by MT/ HL)

Providing and fixing ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS:115622 of approved make, laid on 20mm thick bed of Cement Mortar 1:4(1 cement:4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. a) in colour such as White, Ivory, Grey, Fume Red, Brown (including all leads and lifts carriages of material by MT/ HL)

Providing and fixing gang saw cut mirrior polished premoulded and pre-polished, machine cut for kitchen platforms, vanity counters window sills facias an similar locations of required size, of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joint treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. a) Area of slab upto 0.5 sqm (including all leads and lifts carriages of material by MT/ HL)

Providing edge moulding to 18mm/ 16mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. a) Granite work.

Extra for providing opening of required size and shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble / granite /stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. B) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115 mm size with 50% of cement mortar 1:5 (1 cement:5 coarse sand) admized with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement:5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound to IS:2645 and approved by Engineer-in-charge. D) Finishing the surface with 20mm thick joint less cement mortar of mix. 1:4 (1 cement: 4 coarse sand) admixed with water proofing compo8und conforming to IS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-charge :23.7.1 with average thickness of 120mm and minimum thickness at khurra as 65 mm. sqm (including all leads and lifts carriages of material by MT/ HL)

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS:13592 Type a including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. a) Single socketed pipes. 110mm diameter.

Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticisd-Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5392 leaving 10mm gap for thermal expansion.

a) Coupler 110mm.

b) Single Tee with door 110x110x110mm

c) Bend 87.5* 110mm.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete (including all leads and lifts carriages of material by MT/ HL)

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement:4 fine sand) and curing complete (including all leads and lifts carriages of material by MT/ HL)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e., at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing, paneling and dash fasteners to be paid for separately).

a) Powder coated aluminum (minimum thickness of powder coated 50 microns).

A) For shutter of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) i) Powder coated aluminum (minimum thickness of powder coated 50 microns).

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the direction of engineer-in-charge (Cost of aluminum snap beading shall be paid in basic item). a) With float glass panes 5.0mm thickness (weight not less than 12.50 kg/sqm).

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S.sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. a) With brass cover plate minimum 1.25 mm thickness.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled and glazed shutters 25mm to 40mm thick. a) 12mm thick Marine plywood conforming to IS:710.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). a) Sal wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screw, excluding paneling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:Butt hinges and necessary screws shall be paid separately). a) Second class deodar wood.

Providing and fixing paneling or panelling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled or paneled and glazed shutters 25mm to 40mm thick. a) Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS:3087 marked.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. a) Second class deodar wood.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4mm in both directions with wire of dia. 0.63mm for doors, windows, and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screw as per direction of Engineer-in-charge. a) Second class deodar wood.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. a) Fixed to openings/wooden frames with rawl plugs screws etc.

Providing gola 75x75mm in cement concrete 1:2:4 (1 cement:2 coarse sand:4 stone aggregate 10mm and down gauge), including finishing with cement mortar 1:3 (1 cement:3 fine sand) as per standard design. In 75x75mm deep chase (including all leads and lifts carriages of material by MT/ HL)

Applying priming coat with ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron / steel works.

Applying priming coat, with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Painting on G.S.sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (wooden). Two or more coats on new work.

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screw etc. complete

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screw etc. complete. a) 250x16mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete

Providing and fixing aluminum casement stays, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screw etc. complete.

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS:1868 transparent or dyed to required colour or shade with necessary screws etc. complete: a) Twin rubber stopper.

Providing and fixing brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminum doors including necessary cutting and making good etc. complete.

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS:3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot and double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Providing and fixing anodized aluminum grill (Anodized transparent or dyed to required shade according to IS:1868 minimum anodic coating of Grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as per requirement and direction of Engineer-in-charge, (only weight of grill to be measured for payment).

Filling the gap in between aluminum / stone /wood frame and adjacent RCC / Brick / Stone/wood/Ceramic /Gypsum work by providing weather / structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer in charge complete, complying to ASTM C920, DIN 18540- F ISO 11600. a) Upto 5mm depth and 5mm width.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. a) 2mm thick.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work.

Lettering with black Japan paint of approved brand and manufacture.

Finishing wall premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/ 10 sqm over and including priming coat of water exterior paint applied @ 2.20 kg./ 10 sqm.).

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. a) 25mm dia (heavy type).

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C flushing cistern including flush pipe with manually controlled device (handle lever)conforming to IS:7231, with all fitting and fixtures, complete including cutting and making good the walls and floors wherever required: W.C.pan of Hind ware / Cera make with ISI marked white solid plastic seat and lid.

Providing and fixing of white vitreous china under counter oval wash basin /circular basin (Hindware 10080/kerovit model no.206 & 207) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No.7698+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No.8038 or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever to required as per direction of Engineer-in-charge.

Providing and fixing of white vitreous china wash basin /circular basin with pedestal (Hindware 1008 Ped Cat No.11003 kerovit model no.234 Ped Model No.305) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No.7698+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No.8038 or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever to required as per direction of Engineer-in-charge.

Providing and fixing of C.P. brass Central Hole Basin Mixer without Popup Waste System including with 450mm Long Copper Pipes & Brass Nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar CQT 23167 D/ Kerovit make Cat No.1511010-ND-CP).

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with brackets of same material with snap fitting of approved quality and colour, weighing not less than 105 gms.

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved make confirming to IS : 8931

Providing and fixing C.P. brass robe hook (Jaquar Cat No.ACN 1191N) or approved equivalent) fixed to wall /door with plastic rawl plugs and C.P.brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distance of 37mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88gms.

Providing and fixing of glass shelf 600mm long with all C.P. fittings of approved quality complete item (Jaquar Cat No.CANN 11071 N).

Providing and fixing of regular body concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar Cat No.ALD 083 / Kerovit make Cat No.KB 111030 CP and exposed part Cat No.KB 1511032) with exposed part angular stop cock with flange FUS 29.53.

Providing and fixing PVC connection pipe including all necessary accessories.

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat No.70002) comprising of EWC P cistern, Seat cover, Twin Flush Fittings, Wash Basin 450x300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer-in-charge.

Providing and fixing 6mm copper backed float glass mirror MODI SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative, etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer-in-charge.

Providing and fixing Stainless steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required kitchen sink without drain board 610x460mm bowl depth 200 mm (Pantry).

Providing and fixing testing and commissioning of C.P. brass single hole sink mixer with CP wall flange, swinging spout complete as required and making good as per direction of Engineer-in-charge (Jaquar Cat No.CQT-23167D).

Providing and fixing PTMT towel rail complete brackets fixed to wooden cleats with C.P. brass screws with concealed fitting arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, 78mm wide and effective height of 88mm weighing not less than 190 grams.

Providing and fixing 15mm dia C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (Short body) (Make Jaquar Cat No.CQT-23047).

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (15mm dia) (Make Jaquar Cat No.CON-107KN/Kerovit make Cat No.KB 1511004 CP.

Providing and fixing of Tumbler holder with all fittings as per direction of engineer-in-charge (Make Jaquar Cat No.CAN 114N).

Providing and fixing of wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flenges of approved quality with all fittings (Make Jaquar Cat No.SHA-4791).

Providing and fixing heavy class SS grating plane floor trap and setting in floor with cement mortar to match the floor finish as per direction of Engineer-in-charge (size 100mm dia) ISI marked.

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Polyethylene Aluminum Polyethylene (PE-AL-PE) Composite Pressure Pipes conforming to IS:15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80◦C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. Elbows, tees, reducers, couplers and connectors etc.This includes testing of joints complete as per direction of the Engineer-in-charge. A) Internal work-exposed on wall with clamps at 1.00 meter spacing.

a) 1620 (20mm OD) pipe

b) 2025(25mm OD) pipe).

B) Internal work concealed with clamps at 1.00 meter spacing including cutting the chases and making good the wall etc

a) 1620 (20mm OD) pipe

b) 2025(25mm OD) pipe).

C) External work including trenching and refilling etc. complete.

a) 2025(25mm OD) pipe

b) 2532(32mm OD) pipe

Providing and fixing U clamp with slotted base made of stainless steel AISI 304 18/8. Makes Intello TEC

a) 25mm U clamp

b) 32mm U clamp

c) 100mm U clamp.

Constructing bricks masonry manhole in cement mortar 1:4 mix RCC tob slab with 1: 1.5 : 3 : mix (1 cement : 1.1/2 coarse sand : 3 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in side plastering 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design inside 90 x 80 cm and 45cm deep including CI cover with frames (light duty) 455 x 610mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg with FPS bricks with class designation 75 and with (a) crushed stone aggregate (including all leads and lifts carriages of material by MT/ HL)

Providing & fixing soil waste 7 bent pipes 100mm dia). a) Sand cast iron S&S pipe as per IS:1729.

Providing and fixing plain bend of required degree 100mm dia sand cast iron S&S as per IS:1729.

Providing and placing on terrace (at all floors levels) polyethylene water storage tank ISI: 12701 marked indicating the BIS License nos.with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank (Sintex, Electroplast, Star, Lotus, or equivalent having valid ISI license).

Structural steel works in built up section, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. a) Welded.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20mm nominal size) over PVC sheet 1mx1mx400 micron, finished with 12mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (including all leads and lifts carriages of material by MT/ HL)

Kota stone slab flooring 25mm thick over 20mm (average) thick base laid and over jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing compete with base of cement mortar 1:4 (1 cement :4 coarse sand) (including all leads and lifts carriages of material by MT/ HL)

Making soak pit 2.5m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks and S.W. drain pipe 100mm diameter, 1.8 m long complete as per standard design.

Carriage of the following materials by Mechanical Transport from source to site of work incl. loading, unloading and stacking complete :- a) Sand from Billawar crusher for an average lead of 5.00 Km. by M.T. b) Stone aggregate 40mm nominal size & above from Billawar crusher for an average lead of 5.00 Km. by M.T. c) Stone aggregate (Crusher bajree) below 20mm nominal size from Billawar crusher for an average lead of 5.00 Km. by M.T. d) Bricks from Hiranagar for an av. lead of 75.00 km. by M.T.

Hargovind

RAJ KUMAR

Shiv Rattan

Tilak Raj Sharma

Soni Construction

RAJESH SINGH