REPAIR/MAINT TO DG SET, SERVO VOLTAGE STABILIZER, WATER SUPPLY INFRA AND CONNECTED WORKS FOR AOR OF HQ 6 SECT UNDER AGE(I) CIF(R)

Amount

Servicing of DG Set 62.5 KVA of any Make, checking entire system as per manufacturer's catalogue such as checking all parts for serviceablility, taking down defective parts such as fuel filter assy, by pass filter assembly, lub oil filter assembly, air cleaner assy,air filter, flexible hose pipe, radiator coolent , distill water, Tightening the base bolt and nuts and mounting bolts and nuts. etc and replacing the same with same size, make and capacity of parts, draining out the old used burnt engine oil from the sump cleaning all serviceable filters and oil sump with cleaning solution such as petrol/ diesel and refilling new engine oil upto required level, cleaning of battery terminals with warm water ,Checking the radiator and radiator hose and arresting small leaks ,Checking the fuel pump timing, adjusting if required and complete reassemled and including testing to DG Set to entire satisfaction of Engr-in-Charge. Note:- (i) Spare parts/ Engine oil/ check kit/ filter shall be measured and paid saperately under respective items of BOQ (ii) Minimum 6 months gap/ 200 hrs of run whichever is earlier shall be considered for next service (iii) Repair Guarantee for replaced parts/servicing of DG Set shall be for six month/200 hrs from the date of service. (iv) Cost of small spares required for maint of DG set shall be deemed to be included in the unit rate quoted. (v) Service Engineer must be skilled and must have knowledge of maintenance of DG sets and attending minor and major fault when it arise. (vi) Contractor shall attend and rectify the breakdown in DG Set within 12 hours failing which a recovery of `Rs 1000/hour shall be effected.

Supply only Air filter element (OEM )suitable for 62.5 KVA Capacity

Supply only Diesel filter (OEM manufactured ) with'O' ring (Primary & secondary) suitable for 62.5 KVA Diesel engine

Supply only Oil filter (OEM manufactured ) with'O' ring suitable for 62.5 KVA Diesel engine

Supply only banded cogged belt (OEM manufactured) suitable for 62.5 KVA Diesel engine

Supply only V belt (OEM manufactured) suitable for 62.5 KVA Diesel engine

Supply only fuel pipe (OEM manufactured) suitable for 62.5 KVA Diesel engine

Supply only silencer assembly (OEM manufactured) suitable for 62.5 KVA Diesel engine

Supply only rubber hose for air intake (OEM manufactured) suitable for 62.5 KVA Diesel engine

Supply & pouring in sump/topping up of Engine oil of grade 15W-40/20W-50 in engine or replacement of Engine Make - Servo/Castrol/IOCL/HPCL

Supply only coolant for radiator of any make any type DG set at various loactions all as directed by Engr-in-charge

Taking down brunt unserviceable Automatic Voltage Regulator assy from alternator of DG set by disconnecting its electrical connections, supply and fixing new AVR 12V suitable for 62.5 KVA DG Set including connecting all electrical connections. Testing voltage after starting engine and setting properly if a difference all as specified and directed.

Suply and fixing in replacement of battery terminals (positive and negative) brass heavy duty complete suitable for fixing on battery poles with bolts,nuts and washers complete including taking down unserviceable battery terminals complete all as specified and as directed.

Suply and fixing in replacement of free lead acid battery 12 volts 150 AH confirming to IS 7372 complete all as specified and as directed.

Taking down / Dismantling unserviceable self starter 12 volts from engine of DG Set , opening of stator and armature for repairing by replacing the worn out carbon brushes, brush holder, bearings, ignition / solenoid coil, replacement of burnt armature, rewinding of field coils, replacement of pinion gears,bushing etc, complete servicing , varnishing of stator /armature and refixing after repair, testing / commissioning complete for DG Set any capacity complete all as specified and as directed.

Taking down the existing self starter up to capacity of 62.5 KVA Diesel engine and fixing self starter same as per existing model including testing after complete installation all as directed and specified.

Disconnecting incoming / outgoing cable connection from alternator of DG set and taking out alternator from DG set room checking carefully and transporting to auth workshop aproved by AGE(I) for repair and rewinding of alternator dismentling into parts and cutting the burnt/damage copper winding wire from alternator / stator cleaning slots and rewinding the stator/alternator with super enamelled copper winding wire of existing gauge & size and insulation paper etc complete varnishing of rewinded alternator replacement of carbon brush set bearing set etc complete and transporting the alternator to DG set room coupling with DG set and testing complete including water load test all as specified and directed for 62.5 KVA Capacity of Alternator 415V, 50Hz. NOTE: All neccessary T&P for dismantling,transporting and installation cost is deemed in this work

Taking down the existing turbo charger unit from the capacity up to 62.5 KVA Diesel engine, Transporting to auth workshop aproved by AGE(I). Dismantling opening including replacement of worn out bearing, bushes, fanblade, gaskets, o ring, seal etc. and reassembling testing/ connecting complete all as specified and as directed.

Taking down the existing turbo charger unit from the capacity 62.5 KVA Diesel engine and fixing new turbo charger uint same as per existing model including testing after complete installation all as directed and specified.

Disconnecting, removing and dismantling radiator assembly from the following capacity DG sets and descaling the radiator throughly with CTC solution/ any other chemical solvent agent as approved by the Engineer-in-charge, stopping of leakage at place to copper cores and tubes by brazing scrapping the existing oil paint, dusting and painting the radiator with enamelled paint etc., re-installing and commissioning complete all as specified and as directed for 62.5 KVA Capacity.

Taking down the existing radiator assembly unit from the capacity 62.5 KVA Diesel engine and fixing new radiator assembly same as per existing model including testing after complete installation all as directed and specified.

Taking down the existing defective injector and fuel injection pump (FIP) for the 62.5 KVA capacity of DG set installed at various installation and replacement of worn out spares like delivery valves, nozzles, bearings, fly weight, packing kit, and copper washer kit ,injector element,kit injector,retainer injector cup, fixing tappit cover packing set,and recalibration of FIP and refixing in same position and testing of full load checking of pressure and adjustment by dial gauge complete all as specified and as directed .

Dismantling unserviceable battery charging dynamo from DG set of rating 12 Volts and providing complete repairs and servicing including replacement of bushes, bearings, carbon brushes, rectifiers, rewinding of field magnet coil / rotor armature coils and any other minor parts required all as directed and fixing on engine testing/commissioning complete for DG set having capacity 62.5KVA complete all as specified and as directed.

Dismantling old unserviceable battery charging dynamo of rating 12 volts and supply and fixing new battery charging dynamo same as per existing model suitable for fixing on DG set, 1500 RPM including testing after complete installation all as directed and specified.

Supply and fix replacement of generator control unit as per sample all as directed and specified.

Supply and fix in replacement of exhaust fan (450mm) with connector as per sample all as directed and specified.

Supply and fixing in repair/replacement of unserviceable or broken Door hinges suitable for any capacity and any size canopy of DG set at different locations complete all as specified and directed.

Taking out servo-stabilizer by disconnecting incoming & outgoing connections, removing the top cover on site , replacing the consumble spares only such as gasket, checking fault, cleaning etc, reassembling complete after testing, connecting incoming and out goining connections etc capacity up to 200 KVA complete all as directed.

Material and labour servicing and cleaning of oil cooled servo voltage stabilizer capacity up to 200 KVA by transporting to workshop, carefully lifting of core from the tank by opening cover, cleaning of tank, removing of sediments, cleaning of coils/ electrical connections, filtration of transformer oil, fixing the core back in the tank, making electrical connections by replacing the consumble spares such as gaskets, rubber oil seals complete etc but other spares as listed here-in-after shall be replaced and cost of spare parts as" supply only shall be measured and paid separately under relevent item iron padling back at work site ,working electrical connection all complete as directed by Engr-in-charge. Note: (i) Spare parts required to make serviceable of above oil cooled sevo voltage stabilizer shall be measured and paid separately under relevant item here-in-after. (ii) Contractor shall attend and rectify the breakdown in servo voltage stabilizer within 24 hours failing which a recovery of `Rs 1000/hour shall be effected.

Supply only dimmerstate unit of capacity up to 200 KVA servo voltage stabilizer 28 amps of Make Volina complete all as specified and directed.

Supply only main transformer of capacity up to 200 KVA servo voltage stabilizer of make Volina complete all as specified and directed.

M&L for replacement of Electronic circuit board (Printed circuit board) for controlling of synchronous motor of torque 10 KG and auto/manual under voltage high voltage operation.

M&L for replacement of PCB holder.

M&L for replacement of trigger transformer.

M&L for replacement of panel lamps alongwith connecting leads for over voltage under voltage etc.

M&L for replacement of carbon brush.

M&L for replacement of digital volt meter 72 x 72mm.

M&L for replacement of servo motor 10 KG torque.

M&L for replacement of RC network for 10 KG servo motor

M&L for replacement of auto manual switch.

Material and labour for filling in with new transformer oil for top up to voltage stabilizer having low viscosity of approved make as per IS 355 of 1992 and di-electric strength 40 KV(after filtration) complete all as specified and directed by Engineer-in-Charge.

S & F in replacement of on load change over switch in sheet metal enclosure 100Amp four pole,modular type,positive isolation,door interlock and padlock facility confirming to IS/IEC 60947-3 complete all as directed. Make: Havells Cat no IHCNFE0100 or equivalent cat part of make as specified in list of make here-in-after.

S & F in replacement of Off load change over switch 63 amps 415 volts 4 pole 50 Hz in sheet metal enclosure with out side handel operated complete all as directed by Engr-in-Charge. Make: Havells cat no IHBFFE0063 or equivalent cat part of make as specified in list of make here-in-after.

S & F in replacement of Off load change over switch 100 amps 415 volts 4 pole 50 Hz in sheet metal enclosure with out side handel operated complete all as directed by Engr-in-Charge. Make: Havells cat no IHBFFE0100 or equivalent cat part of make as specified in list of make here-in-after.

S & F in replacement and testing moulded case circuit breaker(MCCB),adjustable Thermal and fixed magnetic type, 4 Pole, 415 volts, 50Hz, breaking capacity 16KA, rating 100Amp,complete as per OEM standard design,all as specified and as directed by the Engineer-in-charge.

All as per item No. 45 here-in-before but rating 160Amp & breaking capacity 36KA.

All as per item No. 45 here-in-before but rating 200Amp & breaking capacity 36KA.

Supply and fix in replacement of gun metal gate valve confirming to IS : 778/1980 CL-1 with iron wheel head screwed both ends for iron pipe of following size.

20 mm dia bore

25 mm dia bore

40 mm dia bore

50 mm dia bore

Supply and laying, connecting and testing galvanised iron medium grade water tubing with all fitting (i.e. Tee, socket, bend etd) and fixtures (ISI marked) confirming to IS:1239 laid in trenches or fixed on wall or in any position including taking out old unserviceable pipes by cutting, screwing and altering the old pipes lines complete of following sizes :- Note: Rates quoted includes for necessary scaffolding arrangement.

20 mm dia bore

25 mm dia bore

40 mm dia bore

50 mm dia bore

M&L for dismentalling all unserviceable part by opening complete Engine and replacing of new following Parts as per OEM, servicing & testing of DG set by taking out of FIP to workshop for repair and caliberation replacing following parts of 62.5 KVA DG Set including reassembling and testing DG complete all as specified and directed. Make of DG set : Kirloskar Note: (i) Spare parts required to make serviceable of above engine of DG set shall be measured and paid separately under relevant item as supply only here-in-after.

(i) C/R Bearing as per existing part

(ii) Piston as per existing part

(iii) Piston Liner as per existing part

(iv) Piston Ring as per existing part

(v) Head Gasket as per existing part

(vi) Head Repair as per sample

(vii) Head Valve as per sample

(viii) Head Seal as per sample

(ix) Set of Joint as per sample

(x) Turbo Charger as per sample

(xi) FIP Repair with replacement of following parts :-

(xii) Injector as per sample

(xiii) Set of Ring for FIP as per sample

(xiii) Pump shaft for FIP as per sample

(xiv) Calibrarion of Fuel injection pump complete including the following parts all as specified and directed :- (a) S & F Benjo bolts for 62.5 kVA DG Set complete all as specified and directed - 02 Nos (b) S & F disel Hose pipe for 62.5 kVA DG Set complete all as specified and directed - 02 Nos

M&L for dismentalling all unserviceable part of 62.5 KVA DG Set AMF Panel and replacing of new following Parts as per existing model and replacing cables, wires, indicator red & green, lugs, strip, line shifter, nut bolts & testing of AMF Panel including reassembling and testing DG complete all as specified and directed Note: (i) Spare parts required to make serviceable of above AMF panel of DG set shall be measured and paid separately under relevant item as supply only here-in-after.

(a) L&T MNX 95-2P, 95A Double pole power contactor, Model : CS94064

(b) Emergency push switch Schneider electric harmony size 22mm Red Non-Illuminated Mushrrom Head push button XB5AS542N

(c) Mushroom Head Push Button Switch Momentary Green size 22mm XB2-BC31

(d) Mushroom Head Push Button Switch Momentary Red size 22mm XB2-BC31

(e) Line Shifter

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of ₹ 43,546.00 during AOC Note:- Tenderers shall not quote for this Schedule

M/S PARSHOTAM KUMAR GUPTA (BID ID -3335257)