REPAIR/MAINT OF ROOF SHEETING, ROOF TREATMENT (INCL LEAKAGE AND SEEPAGE RECTIFICATION), CHAJJAS, FACIA AND MISC WORK IN OTM ACCN IN AOR OF AGE BR-II UNDER GE(WEST)PATHANKOT

Amount

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings or PVC sheet in roof including ridges, sunshades or any position etc complete all as specified.

S&F pre-painted galvalume aluminum zinc coating AZ-150 GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in sunshades ,roof covering, cladding to wall etc fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminum zinc coating AZ-150 GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall and as in ridge etc fixed with self-tapping screws as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for including grills, door, truss, gate, rafters, purlins etc

Dismantling timber scantlings 40sqcm and over in section, in any position as in wooden trusses in framed work of any description.

S&F mild steel work in tubular trusses (framed) /rectangular hollow section/ steel angles, purlines and fastening including distance pieces etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10cm in width or grith not otherwise described for and apply one coat of synthetic enamel paint, complete all as specified and directed.

M&L for cutting down vegetation growths like plants / trees of girth not exc 15 cm & surface are not exc 0.36 Sqm each from roof tops /sides of external walls of buildings, chajja, wall junctions, junctions of rain water / soil /waste vent pipes including taking out roots entered in wall/slab surfaces and making good the surfaces including repairing the CI/GI/PVC joints of affected locations by applying TUFALO chemical (herbal medicine ) to arrest further growth and making good to suit the adjoining surfaces using PCC type 1:2:4, type B-O or cement mortar 1:2 complete all as per manufacturer instructions and as specified. NOTE: Any CI/GI/PVC pipes and fittings damaged during work shall be replaced by new one to insure leakage / seepage free joint without any extra cost to the department and Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to four storeys height of bldgs and removing of debris out of MoD land complete all as specified and directed by Engr-in-Charge.

M&L liquid water proofing treatment to RCC roof slab including dismantling of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as shrubs/roots, fungus, moss, dust including plaster, APP membrane etc. including disposal of debris out of MoD land, in following procedure : (a) Prepare the surface by cleanining with concrete surface grinder/ wire brush and a high pressure water jet and ensure that it is free of dust, oil and loose particles. Damaged portions, hollow area must be repaired with epoxy mortar and repair cracks of old concrete by cutting 'V' groove, corners and joints of drain pipes, channels etc. treated with epoxy mortar prepared with epoxy primer (as per manufacturer's instructions). (b) Laying 10mm thick rendering in Cement mortar 1:3 with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of concrete roof surfaces, finished even and fair to receive treatment on roof Complete (c ) Applying three coats of polyurea waterproofing coating as per manufacturer's instructions for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx. 500% ± 50% and tensile strength at 14 days of 5MPa. (e)The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge / Consultant. (Note:- minimum 6 hrs interval between two coat shall be maintained) (f) All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Note:- (i) Work to be carried out by authorized applicator and as per manufacturer’s instructions. (ii) Providing test with filling of water for continuous 48 hours if there is any leakage than entire treatment will be done again by contractor without any cost. (iii) The rate includes for filling cracks in existing roof with epoxy cement mortar using suitable bonding agent before laying cement plaster.

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, wall, arches, pillars, man-holes, drain etc complete all as specified and directed.

M&L for burnt clay brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per srl item No. 13 here-in-before but excpet brick in CM 1:6 all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.(Note:- WPC shall be measured and paid separately)

Supply only `Liquid Water Proofing Compound complete all as specified and as directed .

M&L for rendering 5mm thick on fair faces of brickwork or concrete surfaces in cement mortar 1:3 as on ceiling complete all as specified and directed.

M&L for rendering 10 mm thick on other than fair face of brickwork or concrete wall surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed

M&L for preparation of new undecorated plastered surfaces of walls and applying three coat of white wash on walls complete all as specified and as directed

M&L for Birla/Altek wall care putty of 1-2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered internally surfaces of wall and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered external surfaces of wall and applying two coats of cement base paint over a priming plastered and other surfaces with alkali-resistance Primer without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered external surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint Apex ultima (Weather coat) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm (weather proof/weather coat) over and including 1.5mm thick wall care putty without any brush marks on the surface in any colour over including necessary scaffolding up to three storeys height of bldgs,Shade/colour shall be approved by GE, complete all as specified and as directed.

M&L for preparation of old plastered internally surfaces of wall one coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment externally surface of wall and applying two or more coats of 100% Premium acrylic emulsion paint Apex ultima (Weather coat) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm (weather proof/weather coat) over and including 1.5mm thick wall care putty without any brush marks on the surface in any colour over including necessary scaffolding up to three storeys height of bldgs,Shade/colour shall be approved by GE, complete all as specified and as directed.

M&L for preparing old plastered or unplastered wall surfaces including cornices,pillasters by brooming down with steel wire brushing scrapping down smoke soot,moulds moss and effloresent salts and treating oily and greasy spots etc and as directed and applying two finishing coat of white wash on wall, complete all as specified.

M&L for preparing old plastered or unplastered wall surfaces including cornices,pillasters by brooming down with steel wire brushing scrapping down smoke soot,moulds moss and effloresent salts and treating oily and greasy spots etc and as directed and applying two finishing coat of white wash on ceiling, complete all as specified.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified .

Taking up or down 20 mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified .

S&F 15mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified .

S&F 20 mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified .

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity white in colour including tank lid, ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including inlet & outlet tank nipple 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and directed by Engr-in-Charge.

S&F Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity white in colour including tank lid, ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including inlet & outlet tank nipple 20 mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair Ball valves 20mm bore high pressure of PTMT with epoxy coated aluminum rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 20mm-210 gms)

S&F in repair for gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and as directed.

Taking down eaves gutter and rain water pipe any size any pattern , PVC/ AC pipe including all fittings ,heads shoes, bends etc including removal to store ,Internal dia of pipe in 75mm/110mm complete all as complete all as specified and directed by Engr-in-Charge.

S&F of PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) bends 75 mm bore any radius, complete all as specified & directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed by Engr-in-Charge.

M&L for Dismantling of wall and ceiling boards (fibre, plup, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S&F false ceiling with fibre cement designer tiles ivory painted (high pressure steam cured) of 4mm thickness (as per IS:14862) and any one of the design (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking metal grid of 605 x 605mm size hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runnerwith suitably spaceed joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600 mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to exising rafter, purlin, etc with galvanised butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T-sections shall be centra black pre-painted with polyester paint, and havng a load bearing capacity of 12Kg/sqm, and refixed all existing electric wiring and fixture all complete at all heights as per direction of Engineer-in-Charge

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 73,790.00 and any other reduction if any from quoted amount.

M/S OM SAI RAM BUILDERS (BID ID -3459495)

BALKRISHAN GUPTA AND SONS (BID ID -3454476)

JAGDISH SINGH ASSOCIATES (BID ID -3454264)

HARI OM ENTERPRISES (BID ID -3450607)

M/S Raghuvanshi Builders (BID ID -3454616)

pardeep singh marwaha (BID ID -3454886)

Substantial Const. Co. (BID ID -3453801)

Ambika Construction Co (BID ID -3452310)