Construction of Compound wall at Engine Division HAL BC

HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Construction of Compound wall at Engine Division, HAL(BC) Cont. No: HAL/FMD/R-41/25-26

Name of the Contractor :

Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3) This BOQ specification has to be read in conjunction with relevant CPWD specifications amended upto date/ detailed technical specification in tender document and tender drawings if any.

1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil, within a lead of 50m, For all kinds of soil etc., all complete as directed by Engineer-in-Charge. 110.00 Cum 253.69 Rupees Two Hundred Fifty Three and Sixty Nine Paise Only 27905.90

2 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 meter and lift upto 1.5 meter etc., all complete as directed by Engineer-in-Charge. 45.00 Cum 191.02 Rupees One Hundred Ninety One and Two Paise Only 8595.90

3 Demolition of Concrete: Demolishing of cement concrete [Nominal concrete 1:3:6 or Richer mix] manually/ by mechanical means including disposal of material within 50 metres, etc., all complete as directed by Engineer-in-Charge.[=2434.25] 15.00 Cum 2372.37 Rupees Two Thousand Three Hundred Seventy Two and Thirty Seven Paise Only 35585.55

4 Painting of exterior old surfaces of walls, etc., Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/liter and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.Two or more coats applied @ 1.43 liter/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 liter/10 sqm. etc., all levels including sccafolding, etc., all complete as directed by Engineer-in-Charge. 450.00 Sqm 176.65 Rupees One Hundred Seventy Six and Sixty Five Paise Only 79492.50

5 Dismantling existing size stone masonry: Dismantling dressed stone work in cement mortar of approximate height 4 meter with necessary safety precautions, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable, after removing the cement mortar from stone and disposal of unserviceable material within 50 metres, etc., all complete as directed by Engineer-in-Charge. 175.00 Cum 2804.59 Rupees Two Thousand Eight Hundred Four and Fifty Nine Paise Only 490803.25

6 Plastering in cement mortar 1:6 (1 cement : 6 fine sand) 15 mm thick to brick work or concrete surfaces finished smooth with trowel including rendering fair finish for exterior surfaces of walls including scaffolding, curing etc., at any height all complete as directed by Engineer-in-Charge. 200.00 Sqm 373.27 Rupees Three Hundred Seventy Three and Twenty Seven Paise Only 74654.00

7 Providing and laying Cement Concrete (1:4:8) at any depth in foundations, in walls or retaining walls, any thickness , size or shape including columns pillars and other similar works curing, de-watering in foundations, etc., complete all as per specifications, drawings etc., all complete as directed by Engineer-in-Charge. 9.00 Cum 5072.92 Rupees Five Thousand Seventy Two and Ninety Two Paise Only 45656.28

8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) and etc., all complete as directed by Engineer-in-Charge. 50.00 Cum 8128.80 Rupees Eight Thousand One Hundred Twenty Eight and Eighty Paise Only 406440.00

9 Form work: Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides , coping and soffits (if any) of foundation and plinth beams,roof slab; and similar work etc.,Centering and Shuttering including strutting, propping etc, and removal of form work, etc., all complete as directed by Engineer-in-Charge. 175.00 Sqm 382.18 Rupees Three Hundred Eighty Two and Eighteen Paise Only 66881.50

10 Steel Reinforcement: Supplying, straightening, fabricating and fixing Steel reinforcement of TMT Bars of not less than Fe 500 grade conforming to IS 1786-1985 for all concrete reinforcement members / works including cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, including fixing and bracing, wastage, welding, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it, etc., complete all as per specifications, drawings. Steel Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above all Level, etc., all complete as directed by Engineer-in-Charge. 3500.00 Kgs 105.12 Rupees One Hundred Five and Twelve Paise Only 367920.00

11 Providing and applying synthetic enamel paint for structural members/pipes in Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture,filling joints,patti, etc., all complete as directed by Engineer-in-Charge. 150.00 Sqm 220.50 Rupees Two Hundred Twenty and Fifty Paise Only 33075.00

12 Disposal: Disposal of building rubbish or waste materials by mechanical means, including loading, transporting, unloading to Outside the division at contractor own place, for all leads including all lifts involved etc., all complete as directed by Engineer-in-Charge. 70.00 Cum 257.24 Rupees Two Hundred Fifty Seven and Twenty Four Paise Only 18006.80

13 Supply,fabricating and erecting Structural steel work with Y frame made out of MS Angles of required size with lugs by cutting to required length & fixing independently by concreting in pockets over the existing perimeter compound wall of approxmately 3.6m height including one coat of Zinc chromate primer with required scaffolding and making provision for placing Concertina Coil Fence and straining & fixing 4 strands barbed wire (2 each on both side of MS Y frame) & 3 nos on vertical face of the Y frame. (Concreting, Barbed wire & Concertina coil will be paid separately) etc., all complete as directed by Engineer-in-Charge. 400.00 kg 130.31 Rupees One Hundred Thirty and Thirty One Paise Only 52124.00

14 Removing of Concertina coil with two layers of electrical wires & barbed wires per running meter ( Agency has to visit the site to see the actual quantom of work) Including removing of poles & structural steel, etc., all complete as directed by Engineer-in-Charge. 80.00 Rmtr 127.12 Rupees One Hundred Twenty Seven and Twelve Paise Only 10169.60

15 Providing struck pointing to size stone masonry with cement mortar (1:4), including making grooves of 'V' or 'U' type, scaffolding, curing, removing cement from stone face, cleaning etc., all complete as directed by Engineer-In-Charge. 450.00 Sqm 127.12 Rupees One Hundred Twenty Seven and Twelve Paise Only 57204.00

16 Supplying and fixing Two layer concertina coil fencing with reinforced barbed tape (RBT) / spring core (2.5 mm thick) wire of high tensile strength of 165 kg/mm² with tape (0.52 mm thick) and weight 43.478 g/m, each coil of 600 mm dia and 10 metre openable length (total length 90 m), having 50 nos. of rounds or any other shape per 6 metre length, upto any height of wall with 'Y' shaped angle iron and horizontal RBT reinforced barbed wire, stud tied with GI staples and GI clips to retain horizontal, including necessary bolts or GI barbed wire tied to angle iron, etc., all complete as directed by Engineer-in-Charge. Note: (i) MS angle and barbed wire shall be paid separately. (ii) Measurement shall be in running metre for both the coils combined . (iii) Contractor has to make adequate arrangements for trimming of branches hindering the coil fixing work and also for barricading the areas where exisitng fence is removed for fixing the new one. Vendor is responsible for safe guarding of cables / conduits / drains running in the periphery of the exisitng compound wall. All safety arrangements like scaffolding, working platform, safety harness, helmet and other PPEs are to be provided by the contractor. [Length of wall will be considered for measurement of Concertina coil] 80.00 Rmtr 635.60 Rupees Six Hundred Thirty Five and Sixty Paise Only 50848.00

17 Constructing size stone masonry using available stones at site in cement mortar 1:6, for foundation well bonded, bedded and solidly hearted, in courses not less than 15 cm high with bond stone at 1.5 m apart in each course and joints squared back, hammer dressing the face stones, edges, laid to levels and including necessary scaffolding, curing, etc., all complete as directed by Engineer-In-Charge. 160.00 Cum 1822.04 Rupees One Thousand Eight Hundred Twenty Two and Four Paise Only 291526.40

18 Providing temporary barricading for the areas where existing compound wall is dismantled (partially / fully) to carry out repair / retrofitting / reconstruction works. The barricading is to be provided using GI sheets up to a height of 3 to 3.5 m, adequately supported with wooden battens / steel posts / columns as per site requirement to ensure that security lapses / pilferages are prevented. The sheets may be taken back by the contractor after completion of the work, etc., all complete as directed by Engineer-in-Charge. 225.00 Sqm 190.68 Rupees One Hundred Ninety and Sixty Eight Paise Only 42903.00

19 Supplying & Fixing barbed wire with horizontal lines of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two MS posts fixed with G.I. staples or G.I. binding wire tied. Payment to be made per metre cost of total length of barbed wire used, etc., all complete as directed by Engineer-In-Charge. 750.00 Rmtr 13.65 Rupees Thirteen and Sixty Five Paise Only 10237.50

Sub-Total (Excluding GST) Rupees Twenty One Lakh Seventy Thousand Twenty Nine and Eighteen Paise Only 2170029.18

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 2170029.18 BELOW % 2170029.18

Add 18% GST Rupees Three Lakh Ninety Thousand Six Hundred Five and Twenty Five Paise Only 390605.25

Grand Total (Including GST) Rupees Twenty Five Lakh Sixty Thousand Six Hundred Thirty Four and Forty Three Paise Only 2560634.43

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qulification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/R-41/25-26

Name of Work: Construction of Compound wall at Engine Division, HAL(BC).

Estimated Amount in Rs.: 2560000

Tender Notice Date : 07.07.2025

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3

Sl.No Description Details Enclosed / Not Enclosed Remarks

1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual/firm/company

2 Type of ownership PlsEnter Type of Ownership

If Other, please specify

3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc., Pls enter Details of Constitution

4 Address for correspondence: Pls Enter Address

5 (a) PAN No.: Pls Enter Pan NO

5 (b) Service Tax Registration No

5 (c ) Goods and Service Tax ID No.

6 Contact details

Contact person name Please Enter Contact person Name

Mobile No. Pls Enter Mobile No

Ph. No. with STD code

FAX No. with STD code 3 #N/A

7 Registered Contractor

If Registered Contractor with HAL Yes/ No Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs 0 7 E 1

Registration No. 199999 7 F 2

Category 200000 6 G 3

PEMD Amount ( If paid ) 499999 6 H 4

8 I.T Returns for past 03 years 999999 5 J 6

2024-25 Pls Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7

9 Average annual financial turn over during the last 3 years, ending 31st March 2024 of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3

YEAR TURN OVER IN Rs. Enclosed / Not Enclosed REMARKS 5000000 2

2023- 2024 Rs. Pls Enter Turn over in Rupees for all the 3 years 7499999 2

Average annual Financial turn over 0.00 768000.00

Avg Annual Turnover criteria is not met 10000000 1

10 ESI & PF Nos with proof Nos Enclosed / Not Enclosed

ESI Registration No/. with proof if any Remarks if any

PF Registration No. with proof if any

11 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Name of the Bank

Type of Account

12 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission solvency cal

Name of Bank & Branch Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs #REF! 28-Jun 0 40000

Date of Issue 200000 40000

Value in Rs. 200001 150000

Solvency value is NOT as per NIT

13 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender. 1024000 500001 250000

Completed similar works during last 7 years Pls Select %of similar works completed during last 7 years 1000000 250000

Work NoI Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Brief Description of Work: Please enter Details for Work No 1 2000000 500000

Completed value of Work in Rs. 2000001 1000000

Date of Commencement of Work 4000000 1000000

Date of Actual Completion of Work: 4000001 2000000

Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Brief Description of Work: Pls Enter Details for Work No II

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work: work done

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal #REF! 2555

Brief Description of Work: Pls Enter Details for Work No III #REF!

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work:

14 Details of person holding the power of Attorney (If different from contact person)

Name Related Document to be Uploaded to eProcurement Portal

Mobile No. Pls Enter Details for Person holding Power of Attorney

Ph. No. with STD code

FAX No. with STD code

15 DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

16 DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Pls Accept the Delaration II