SPECIAL REPAIRS TO BUILDING NO P-73 (DEF CIV MD ACCN), PROVISION OF CGI SHEET IN LIEU OF EXISTING ASBESTOS SHEET OF BUILDING NO NP-01 (ADM BLOCK) OF AFMSD AND PROVN OF ROLLING SHUTTER IN BLDG NO NP-3 (GROUP-I) OF AFMSD AT KANDIVALI UNDER GE (N) MUMBA

Amount

Material and labour for surface preparation of existing concrete components including grinding/rubbing carefully by grinder without damaging the existing concrete including cleaning the surfaces by blower , removal of external plaster wherever exists. Cost inclusive of transportation, labour conveying debris away from the Defence land, tools and tacklers, lead and lift and clean water thoroughly complete all as specified and directed by Engr-in-Charge.

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Supply and fix mild steel TMT bars, 5 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description in any position including necessary scaffolding arrangement (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge.

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour but excludes the materials for grouting the pins etc complete all as specified and as directed by Engineer-in-Charge.

Repairing of excessively damaged concrete portion by using superfluid dual shrinkage compacted and providing, casting with micro concrete of grade M-40 at all levels with all leads and lift as directed including mixing, laying, levelling, finishing including curing and formwork of steel or marine ply complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

Material and labour for reinforced cement concrete M-20 (design mix) (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc complete as directed by Engineer-In-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB of Krishna Conchem or equivalent of approved make and quality comprises of resin and hardener mixed as per manufacturer's instructions with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE Note: (a) New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work.

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforming to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method for joining old and new concrete as per technical specifications of manufacturer complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE Note-Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

Material and labour for providing and laying average 20 mm thick POLYMER MODIFIED MORTAR over identified R.C.C. members in One layer of approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE Note for Item No.1 to 12:- (i) The work under Item No. 1 to 12 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above. (iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfillment of fitness criteria of structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority.

Taking down cement plaster of any description on brick or stone walls or in concrete surfaces as in drain etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 10 mm thick cement plaster using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S : 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including dubbing of plaster for levelling purpose with same ready mix plaster including provisione of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry before plastering including scaffolding at any height and all safety materials required for execute work etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Material and labour for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Sound last PMC-1 of M/s Sound build care Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S : 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engineer-in-Charge. Make :- Dr Fixit/Fosroc/krishna Conchem /BASF/Sika

Material and labour for preparation of newly plastered internal surfaces of wall and applying two coats of oil bound distemper with roller mixed with EC-20 chlorophyriphos as per manufacturer's instructions over a coat of alkali resistant wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper with roller mixed with EC-20 chlorophyriphos as per manufacturer's instructions over a coat of alkali resistant wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat with roller mixed with EC-20 chlorophyriphos as per manufacturer's instructions, over one coat of acrylic primer on wall complete all as specified and as directed by Engineer-in-Charge Make- 1 “APEX ULTIMA” of Asian Paints 2 “WEATHER COAT ALL GUARD” of Berger Paints 3 “EXCEL TOP GUARD” of Nerolac 4 “DULUX WEATHERSHIELD MAX” of ICI India

Material and labour for complete removal of existing treatment and applying two coats of distemper oil emulsion, mixed with EC-20 chlorophyriphos as per manufacturer's instructions, over a coat of alkali resistant primer on plastered or other surfaces of wall complete all as specified and as directed by Engineer-in-Charge. Make: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)

Material and labour for complete removal of existing treatment on ceiling surfaces and applying two coats of distemper oil emulsion, mixed with EC-20 chlorophyriphos as per manufacturer's instructions, over a coat of alkali resistant primer complete all as specified and as directed by Engineer-in-Charge. Make: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)

Material and labour for complete removal of existing treatment of wall surface and applying two coats of Acrylic weather proof coat 100% exterior grade paint with roller mixed with EC-20 chlorophyriphos as per manufacturer's instructions,over one coat acrylic primer complete all as specified and as directed by Engineer-in-Charge. Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India

Material and labour for preparation of un decorated wall surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of undecorated ceiling surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Taking down chowkats or frames with shutter (without taking off shutter from frame) not exceeding 1.5 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Taking down chowkats or frames with shutter (without taking off shutter from frame) exceeding 1.5 sqm but not exceeding 4 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Taking down shutter carefully, area exceeding 1.0 sqm but not exceeding 2.0 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 180 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge. Note- The quoted rates deemed to include for cuting holes, providing concrete for holdfast and making good the the disturbed surfaces to match with the existing surface. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat molded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 176 of SSR Part II (pertaining to item No 08080) including necessary aluminium builders hardware for one door to be provided such as 100mm dia butt hinges - 3Nos, tower bolt 200mm dia - 2Nos, handle 200mm long - 2 Nos etc complete all as specified and as directed by Engineer-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel work as in hold fast & similar small articles, conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed plates, concrete block for hold fast etc including necessary formwork complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 30mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both side complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 35mm thick factory made 2nd class hard sal wood glazed and skelton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pvts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-charge.

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix stainless steel butt hinges, medium weight, 100mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 200mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint, mixed with EC-20 chlorophyriphos as per manufacturer's instructions, over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimar paints/ Dulux

Material and labour for preparing old wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint, mixed with EC-20 chlorophyriphos as per manufacturer's instructions, complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimar paints/ Dulux

Supply and fix 15 micron coloured aluminium sections for sliding (3 Track) or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 4.0mm thick black glass, ordinary quality, in square exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick figured glass, pin headed type ordinary quality, fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supply and fix 15 micron coloured aluminium anodised grill of design No DG-101 or RG 102, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Demolition of brick work/stone masonry built in cement mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan, to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete 1:4:8 type D2, using 40mm graded stone aggregate as in sub base of flooring/ hard standing/path and finished even and fair without using extra cement etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for 75mm cement concrete (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection and finishing the surface even and smooth without using extra cement including joints in plinth protection to be filled with bitumen mastic (1:3) as specified and as directed

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in Cement Mortar (1:6) complete all as specified and as directed by Engineer-in-Charge. Make: H R Johnson / Orient Bell Tiles / Kajaria / Somany Tiles Ltd / Nitco tiles / Swastik Tiles / RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in Cement Mortar (1:6) complete all as specified and as directed by Engineer-in-Charge. Make: H R Johnson / Orient Bell Tiles / Kajaria / Somany Tiles Ltd / Nitco tiles / Swastik Tiles / RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in colour cement to match including 10mm thick backing coat in Cement Mortar (1:4) etc complete all as specified and as directed by Engineer-in-Charge Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles / RAK tiles

Material and labour for glazed coloured ceramic tiles, 1st quality of size 350 x 250 x 7 mm thick or 450 x 350 x 7mm thick (or nearest size) on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in colour cement to match including 10mm thick backing coat in Cement Mortar (1:4) etc complete all as specified and as directed by Engineer-in-Charge Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles / RAK tiles

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, vertical surfaces etc., laid, bedded, and pointed in any mortar and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Material and labour for machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 20mm thick in cement mortar 1:3 base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing etc complete all as specified and directed by Engineer in Charge.

Ditto all as per item No 62 above but in riser of steps, skirting, dado and pillar laid over a backing coat of 15mm thick in cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

Material and labour for rounding the edges of stone slab as in steps, cooking platform and similar situations complete all as specified and as directed by Engineer-in-Charge.

Material and labour for chequered cement concrete tiles 30cm x 30cm x 25mm thick with grey cement and no pigments, set, jointed and pointed in neat cement slurry in floors including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. Make- (a) M/S Mehatab Tiles, Indore (b) National Tiles(c) Bharat Tiles and Engg Coy, Bangalore (d) Modern Tiles and Marbles Bangalore (e) M/s NITCO, Mumbai (f) Ultra (g) Duracrete

Material and labour for 20-25 mm thick machine cut cudappa stone slab in jambs / cills / soffits of window / ventilator as in frame work to support for aluminium section, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete over backing coat 15 mm thick in CM (1:3)complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 20mm thick makrana, colour/white marble, machine cut, (table rubbed and polished) as in steps, jambs, pillars, window cill, kitchen platform & like, set, bedded and jointed with grey cement slurry & pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, nosing, moulding of edges as required, rubbing and polishing etc, laid over and including screed bed or bedding layer of 15mm thick in cement mortar (1:3) all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix in repairs mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix in repairs mild steel tubing medium grade 25mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Dismantling of 110 mm dia cast iron / PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Dismantling of 75 mm dia cast iron / PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix PVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix PVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix PVC (SWR) vent cowl 110 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix PVC (SWR) vent cowl 75 mm dia complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix 32mm dia low density polyethylene pipes (LDPE) of pressure rating @ 6 kgf/ cm2 fixed to wall complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs UPVC floor trap 75mm with grating including jointing with waste pipe Complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs, concealed stop valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs tubular towel rail aluminium anodised 20mm dia, 'D' type, 60cm long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fix brass chromium plated 125mm Swivel shower for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and as directed by Engineer-in-Charge. Make- Jaypee /GMP / Neta/ Zolota/Prayag Polymer/ Symet

Material and labour for providing stages wise waterproofing treatment to sunken portion of toilets as under and as directed by Engineer-in-Charge. Stage 1: Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris outside MD land etc complete all as specified and directed. Stage 2: Providing 15 mm thick plaster in CM 1:3 mixed with integral water proofing chemical of STP Ltd in the proportion /quantity all as per manufactures instructions. Stage 3 : Primer - Mix Tarfelt LM with water in ratio 1:1 @ 250 gms/sqm and apply the primer on the plaster surfaces Stage 4 : Application of 1 st coat of Tarfelt LM of STP Ltd without dilution with water@1kg/sqm by brush all as per manufactures instructions. Stage 5: Laying 50 GSM fibber glass cloth over the 1st coat while the coated surface is still tacky Stage 6: After 6 to 7 hours interval apply second coat i.e final coat of Tarfelt LM without dilution with water of STP Ltd by brush as per manufactures instructions.@1KILOGRAM/Sqm Stage 7: Providing 10mm thick protective plaster in CM 1:3 mixed with STP NO -1 @ 250ml/50KILOGRAMcement all as manufacturer's instructions.

Material and labour for plain cement concrete 1:5:10, type E-2, Using 40 mm graded stone aggregate, as in lean concrete complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : Slimline/Commander/Hindustan.

Supply and fix flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs, PVC Nahani trap,75 mm dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix in repair PTMT grating doom over Nahani trap and floor trap of 100mm Dia (Min Wt 25 gms) complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair PVC connection, 15 mm size 450 mm long both end socket fix complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs vitreous china wash hand basin white flat back size 400 x 330 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed. Make : M/s Hindustan Sanitary Ware / Parryware / Neyveli Ceramics (Neycer) / CERA / Hindware

Supply and fix in repairs, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever CI brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste pipe etc complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fix in repairs rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 1000 ltrs capacity with inlet & outlet connections, tank nipple, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Sintex/Polycon/infra/Rotex

Supply and fix in repairs PP-R gate valve(brass insert), 32mm bore, fixed with suitable size of new union complete all as specified and as directed by Engineer-in-Charge. Make : Make : PRINCE (Greenfit)/ Finolex/ Supreme/ SFMC

Supply and fix in repairs Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed of 25mm bore complete all as specified and as directed by Engineer-in-Charge (Minimum weight - 142 gms) Make- Jaypee /GMP / Neta/ Zolota/Prayag Polymer/ Symet

Supply and fix Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete / cement lime concrete / mud faska (unreinforced in roof and terrace other than ground floor) any description and removal of rubbish to outside MD land etc complete all as specified and as per directed by Engineer-in-Charge.

Material and labour for providing plain cement concrete 1:2:4, type B0 using 12.5mm graded stone aggregates mixed with water proofing compound at the rate of 2% by weight of cement as in levelling course, haunching, coping, and similar work, over RCC roof surface and RCC over head tank top surface including rounded or chamfered on edges and formwork etc, laid in slope as required, finished even and fair etc complete all as specified and as directed by Engineer-in-Charge. Note: Water proofing compound will be measured and paid separately

Material and labour for APP modified waterproofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.90 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide 20mm thick screed in cement mortar 1:4 mixed water proofing compound at the rate of 2% by weight of cement (d) Provide 300 x 300 x 20mm thick machine pressed cement concrete tiles with minimum thickness of joint (not exceeding 3mm) are thoroughly filled with water proof polymer based joint mortar. Note : (i) water proofing compound will be measured and paid separately. (ii) Quoted rate includes the disconnection existing tanks of any liters capacity incl. all fittings, setting aside (for lowering if req) for roof treatment & reconnecting and refixing in position incl. all fittings complete all as directed. Make of APP Membrane- (a) STP Ltd (b) Texsa India Ltd (c) IWL Ltd (d) TIKIDAN Make of Tile- (a) M/S Mehatab Tiles, Indore (b) National Tiles(c) Bharat Tiles and Engg Coy, Bangalore (d) Modern Tiles and Marbles Bangalore (e) M/s NITCO, Mumbai (f) Ultra (g) Duracrete

Material and labour for APP modified waterproofing treatment to parapet wall with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4 lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.90 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide a solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm prescribed by manufacturer complete all as specified. Make of APP Membrane- (a) STP Ltd (b) Texsa India Ltd (c) IWL Ltd (d) TIKIDAN Note : Quoted rate includes the disconnection existing tanks of any litres capacity including all fittings, setting aside (for lowering if reqd) for roof treatment & reconnecting and refixing in position including all fittings complete all as directed.

Material and labour for removing vegetation, trees, plants and shrubs etc in any position by cutting hole into brick wall / concrete surfaces (for removing the roots of trees/plants) area not exceeding 0.50sqm each and using acid to burn the all roots of tree/plants and making good disturbed surfaces with cement concrete 1:2:4 type B1, using 20mm graded stone aggregate mixed with and including water proofing compound @ 3% by weight of cement and including making good adjoining surface with existing finishes all as specified and as directed by Engineer-in-Charge. Note: The unit quoted rate shall be deemed to include WPC & necessary scaffolding as required.

Material and labour for demolition of reinforced concrete in roofs, floors (other than ground floors), beams, staircase landing, chajjas and similar suspended works and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts to be covered /protected by water proof aluminium butyl tape commercial type or rubberized anti leak water proofing spray or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Material and labour for MS framed work such as grills , gratings, etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, framed work of garbage bin, barred iron doors, ladders, framed balusters, walk ways, railings, framework of watertanks and similar work conforming to FE 290 Gde 165 etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer with all necessary staging, scaffolding etc as required complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints / Berger paints / Shalimar paints / Dulux

Material and labour for preparation of old painted steel surfaces of any description, over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint with all necessary staging, scaffolding etc as required complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints / Berger paints / Shalimar paints / Dulux

Supply and fix 1mm thick stainless steel plate rack of size 900 x 600 x 200mm including fixing with rawal plug ang screws complete all as specified and as directed Make: Blue Star cat No kpr - 313/ kpr- 314 or equivalent of Nirali / parryware / Prayag as approved by GE

Material and labour for Prelaminated particle board 18/19mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame including taking down existing etc complete all as specified and as directed by Engineer-in-Charge. Make: Greenply / Kitply / Century Plywood / Associates Decor Ltd

Supply and fix 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished all as specified and as directed by Engineer-in-Charge.

Supply and fix Ball catcher with 8mm dia steel ball and brass body and striking plate including letting in and fixed all as specified and as directed by Engineer-in-Charge.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 150mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flaps (when open) 40mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Dismantling plain or corrugated Asbestos cement sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts to be covered /protected by water proof aluminium butyl tape commercial type or rubberized anti leak water proofing spray or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets Note: Rates of item no 112 & 124 are inclusive for points of self tapping screws to be covered/ protected by water proofing aluminium butyl tape commercial type or rubberised anti leak waterproofing spray, all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 10 mm thick in cement mortar 1:4 on internal wall surfaces and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick rendering on fair faces of brick or concrete surfaces, mixed with water proofing compound, in CM 1:4 finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.. Note: WPC will be measured and paid separately.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper with roller mixed with EC-20 chlorophyriphos as per manufacturer's instructions over a coat of alkali resistant wall primer over 3mm thick layer of wall care putty complete all as specified and as directed Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for 1.25mm thick steel rolling shutters, with ball bearing, gear operated type with bevel gear box and crank handle, safety lever locks mild steel with 4 levers as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position etc complete all as specified and as directed by Engineer-in-Charge. Make : M/s Swastik Rolling Shutters, Mumbai / M/s Shree Lakshmi Engg Wks, Bangalore / M/s Senthil Rolling Shutters & Engg Co, Chennai / M/s Jayaraj Industries, Chennai

Taking down carefully copper / aluminium point wiring with PVC casing (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials out side MD land in case of Credit and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

Material and labour for (concealed type ) point wiring including necessary chases cutting of wall for complete with PVC insulated FRLS cable unsheathed 1100 volts grade with multi stranded copper conductor conforming to IS-694, 1.5sqmm (nominal area) drawn through and including non metallic PVC conduit 20mm dia (ISI marked) and accessories laid on surface of wall/roof with sunken type pressed steel/welded terminal boxes made out of 1.6mm mild steel sheet, modular cover plates for mounting of switches, socket outlets, regulators etc., including provision of PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor 1.5sqmm as earth continuity conductor and connecting to common earth dolly for One light / call bell / Fan controlled by one, one way switch complete including making good of the distrubed surfaces as per existing complete all as specified and as directed by Engineer-in-Charge. (i) Red wire use for live connection, black wire use for neutral and green wire use for earthing . Separate cable for earthing and neutral to be used for each individual circuit from the DB for each board. Note: Serviceable switch / socket outlet shall be reused. Make of Cable-Plaza, Finolex, Havells, Polycab Make of PVC conduit-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme

All as per item No.130 here-in before but One 3 pin, 5/6 Amps switch socket combination point on the independent board

All as per item No.130 here-in before but for one 3 pin, 5/6 Amps switch socket combination point on same board with other switches controlled by one switch.

All as per item No.130 here-in before but for 3 pin 15/16 Amps switch socket combination on independent board with 2.5sqmm copper cable and provision of 2.5sqmm PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor for earth continuity conductor in green colour connected to common earth dolly connecting up to fittings complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Ceiling rose, surface type Bakelite, three terminal PVC/ polycarbonate isolated body, 65x32mm, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix Call bell electric (Ding Dong type) suitable for working on 230 volts AC supply complete all as specified and as directed. Make: Anchor / Legrand / L&T

Supply and fix Modular type fan regulator rotary step deluxe, 240 volt, 50Hz 2 MODULE all as specified and as directed by Engineer-in-Charge. Make: Make: Legrand-Myrius Cat No 679241 or equivalent in L&T / Honeywell/Crabtree/leader/Anchor

Supply and fix Modular type bell push one module for call bell single pole one way 6 Amps, 240 volt, 50Hz all as specified and as directed by Engineer-in-Charge. Make: Legrand-Myrius Cat No 679218 or equivalent in L&T / Honeywell/Crabtree/leader/Anchor

Supply and fix Modular type switch socket outlet combination, 2 in 1, 3 Pin, 16 Amps, flush type, universal ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Legrand-Myrius Cat No 679226 or equivalent in L&T / Honeywell/Crabtree/leader/Anchor

Supply and fix Modular type switch socket outlet combination, 2 in 1, 3 Pin, 6 Amps, flush type, universal ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Legrand-Myrius Cat No 679235 or equivalent in L&T / Honeywell/Crabtree/leader/Anchor

Supply and fix Modular type switch, single pole, one way, 6 Amps, flush type, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Legrand-Myrius Cat No 679200 or equivalent in L&T / Honeywell/Crabtree/leader/Anchor

Supply and fix in repairs batten type LED tube light fitting, 1x20 watts, 230 volt, 4 feet with long lasting all pre-wired fixed on walls with all fixing accessories such as 2 Nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20sqmm complete all as specified and directed by Engineer-in-Charge-in-Charge, Make : Havells Cat Part No LHEXACP7UN1W020 or equivalent in Bajaj / CG / Phillips model no. BN021LED20S-4ft

Supply and fix LED light fitting 1 x 13 watts, bulkhead luminaries including LED light deriver holder, connection with three core copper flexible cable 16/0.20mm from ceiling rose to fitting etc wih fixing accessories including taking down existing light fittings etc complete all as specified and as directed by Engineer-in-Charg Make : Havells cat Part No LHEXCGP7UN5W013 / Phillips / CG / Wipro/Bajaj

Supply and fix angle holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply & Fix LED bulb of capacity 9 watt, retrofit type to fit in lamp holder complete all as specified and directed. Make: Havells/Bajaj/ CG/Shakti

Supply and fix in repairs ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) including suitable size of hanging clamp, nut and bolt etc complete all as specified and as directed by Engineer-in-Charge. Note: Old ceiling fan will be deposited in MES store yard Make : Usha, Model : Technoair BLDC 5 Star, Colour : White or equivalent of Bajaj /Orient/Havells/crompton

Supply and fix in repairs exhaust fan, made of steel body complete with louvers shutter, voltage 230 v, 50 Hz, RPM 1200, copper winding of sweep 300 mm including taking down existing exhaust fan etc complete all as specified and as directed by Engineer-in-Charge. Note: Old fan will be deposited in MES Store yard. Make: Usha, Crompton Greaves, Bajaj

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 100 Amps rated bus bar, 240 volt, horizontal type, IP 43 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Schneider / Havells / L&T / ABB / Legrand / Siemens / Benlo/Larsen & Toubro.

Dismantling and taking down old unserviceable meter cabinet of any description after necessary disconnection of all incoming and outgoing connections complete and supply, installation, testing and commissioning of indoor type, MS angle fitted with bolts and nuts in ground meter cabinet of suitable size made out of 2.0mm thick CRCA MS sheet with front door having glass window for viewing KWh meter and other doors shall be opaque. All doors should have gasket and locking arrangement and the cabinet shall be painted both interfamily and externally with two coats of synthetic enameled paint (Shade - Smoke Grey) over a coat of red oxide meter primer duly sprayed with the compressor. The cabinet shall be dust and vermin proof with degree of protection of IP 43. The cabinet shall be comprising with the following accessories :-

(a) Four pole MCCB, 40 Amps, with breaking capacity 10KA having adjustable thermal and fixed magnetic/ release-1 No. Make -Legrand / L&T / Siemens / Schneider / Havells. (b) Aluminum bus bar of cross section 40 x 5mm duly mounted on FRP/DMC insulations and necessary drilling (1 incoming & minimum 4 outgoing) for connections and duly covered with heat shrinkable PVC sleeves of stranded colour code -04 Nos Note : Busbar chamber shall be covered with necessary CRCA sheet cover duly screwed so that live part shall be exposed. (c) Single phase smart KWh meter of rating 10-60 Amps confirming to IS-16444 of 2020 suitable for prepaid metering , 230 volts,50 Hz- 06 Nos (d) Internal wiring of meter / MCB / Cable connector, shall be carried out with 10 Sqmm multifexible copper wire with FR grade PVC insulation of 1100 volts rating including necessary lugs / nuts/ bolts/ washers etc : Make of wire- Havells / Polycab / Finolex. (e) LED indicating lump (R-Y-B) suitable for AC 230 volts single phase supply -3 Nos Make - RAAS /SIEMENS / L&T (f) MCB 32 Amps, SPN - 07 Nos Note : Old unserviceable KWh meters shall have to be deposited to MES Store.

Supply and fix in repairs MCB SP, 6 Amps to 32 Amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider//BENTEC

Supply and fix in repairs MCB SPN, 32 Amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider//BENTEC

Material and labour for MCB blanking plate complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

Material and labour for Sub main wiring ( Concealed type ) complete with and including 2 runs of 4sqmm single core FRLS PVC insulated and unsheathed multi stranded copper conductor cable single core 1100 Volts grade drawn through and including non metallic PVC conduit 25mm dia, medium grade, including accessories and fixed on walls and 4 sqmm FRLS PVC multi stranded copper conductor cable for earthing and connected to common earth dolly including cutting chases & making good disturbed surfaces of walls, taking down the existing sub main wiring etc complete all as specified and as directed by Engineer-in-Charge. Note : Two runs of 4 sqmm PVC insulated cable and one run of 4 sqmm earthing cable and one run of PVC conduit shall be measured as one unit length. Make of Cable-Plaza, Finolex, Havells, Polycab Make of PVC conduit-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme

Material and labour for Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 4 mm dia, 7.5m long, by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt not less than 50 Kg and Benzonite powder 20 Kg in each earthing packed up to maximum 30 cm on both side of plate and packed upto minimum 150 mm all around the earth plate, and protected by 15 mm bore light grade galvanised iron pipe and connected to control board / panel / equipment complete all as shown in electrical plate No.3 of MES schedule Part I with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavation and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames with shutter (without taking off shutter from frame) exceeding 1.5 sqm but not exceeding 8 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 76,669.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

joshua construction

K Vani Construction