Repair/Maint of Solar Light, Gate/Garden Light and allied works at AF Stn and Periodical Maint of Fire Alarm System at 19 Wg, AF and Periodical Maint of EOT Crane installed at 14 BRD, AF under GE (AF) Borjhar

Amount

Supply, install, testing and commissioning of stand alone, all in one type Integrated LED Solar Street Lighting System of 30 W capacity, 3000 Lumen beam angle 135/85, system efficacy > 100, CCT 5700, CRI> 70 with built in high efficiency solar panel of 90Wp mono crystal module & battery cap of 12V, 30 Ah, LiFePO₄ type with high efficiency micro processor based charge controller and PIR sensor, should have dusk to down operation & designed back up for 12 hrs at full or with dimming approx 24 hours and lighting system shall be equipped on 6.0 m long pole with base plate and finial taper plug, [nominal bore : 65mm, medium grade ] minimum 3.6mm thick complete all as specified and as directed. Make Philips, Cat No. BRP710 LED 30 CW MR S1 12V LFP AIO Solar Equip IN) / Orient, Cat No. LSSN-30C90-30P or equivalent model from make Havells/Philips/ Crompton/ Bajaj. NOTE : (a) The 1/6 length of the pole shall be planted on the ground through earth and PCC works. The base for pole foundation shall be 0.6X0.6X0.01 m, foundation for the pole be 0.45X0.45X1.0 m and coping be .015m radius around the pole of 0.03 m long above ground level (b) Earth work and PCC works shall be measured and paid separately, however form work for the PCC foundation shall be deemed to be included in this rate. (c) The manufacturer shall provide unconditional warranty for two years along with battery for solar lighting system excluding pole and contractor shall produce necessary documents for the same before taking any payment from the department.

Excavating in trenches not exceeding 1.5m wide and not exceeding1.5m in depth/width for planting of solar street lighting poles and getting out in soft/loose soil complete as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm for planting of solar street lighting poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws complete all as specified and as directed.

Removing of surplus excavating material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point for planting of solar street lighting poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws complete all as specified and directed.

M&L for PCC (1:4:8) Type D-2 (using 40mm graded stone aggregate) for preparing base for planting of solar street lighting poles / foundation including necessary formwork (as reqd) complete all as specified and as directed.

M&L for cleaning of electronically addressable intelligent detector after dsconnecting all electrical connections as per OEM recommendations all as specified and directed.

M&L for taking down SMPS Adapter after dsconnecting all electrical connections as per OEM recommendations all as specified and directed.

S&F SMPS Adapter 24V, 2A Make- Protek incl testing checking etc. complete as per OEM recommendations all as specified and directed.

M&L for taking down RS 485 network card for Fire Alarm Control Panel after dsconnecting all electrical connections as per OEM recommendations all as specified and directed.

S&F RS 485 network card for Fire Alarm Control Panel incl testing checking etc. complete as per OEM recommendations all as specified and directed.

M&L for taking down RS 485 to Optical media converter after dsconnecting all electrical connections as per OEM recommendations all as specified and directed.

S&F RS 485 to Optical media converter incl testing checking etc. complete as per OEM recommendations all as specified and directed.

M&L for detection of OFC cable fault through OFC cable fault locator all as specified and directed.

M&L for jointing the damage OFC cable through OFC cable Jointing Kit complete all as specified and directed. Note:- Any earth work, sand cushioning & brick protection for OFC cable shall be measured & paid separately.

Excavating in trenches manually not exceeding 1.5m wide and not exceeding1.5 mtr in depth/ width for laying under ground cable / foundations and getting out in soft / loose soil all as specified and directed. Note: During excavation no mechanical excavator is permitted at site, contractor will do the excavation through maually.

Returning, filling in incl spreading, leveling, watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing of surplus excavating material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

M&L for sand cushioning for protection of lT under ground cable with screen wash sand and punning to proper reqd cover all as specified and directed.

M & L brick protection with old size sub class ‘B’ brick for PVC under ground cable protection in trench with width equal to length of brick laid dry and flat joining each other with gap between adjacent brick not exceeding 10mm over LT under ground cable all as specified and directed.

M&L excavation in trenches not exceeding 1.5mtr wide & not exceeding 1.5mtr depth for making inspection pit in hard/soft soil including removing excavated materials not exceeding 50mtr and depositing where directed at a level not exceeding 1.5mtr above the staring point all as specified and directed.

M&L for cement concrete in foundations, filling and mass concreteType C2 1:3:6, 40mm graded aggregate all as specified and directed.

M&L for PCC as in foundation for inspection pit or any other works type C1 (1:3:6) (20mm graded aggregate) all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, set in cement mortar 1:6 complete all as specified and directed.

M&L rendering 10mm thick in CM 1:6 on fair faces of brick works or concrete surfaces all as specified and directed.

M&L for dismantling / taking down cross-arms of M.S. channel or angle sections / pit cover etc. complete and setting aside for taking credit complete all as specified & directed.

M&L for replacement of inspection pit cover or any other works made up of 3mm thick MS Sheet with locking arrangement (as reqd) including fabrication works such as cutting, welding & bent to shape and painting with two coats of black japan paint over a coat of red oxide primer on steel surfaces of any description over 10cm in width or girth including preparation of new untreated surfaces complete all as specified and directed.

M&L angle iron / flat bar of required sizes with locking arrangements including fabrication works such as such as cutting, welding & bent to shape and painting with two coats of black japan paint over a coat of red oxide primer on steel surfaces of any description over 10cm in width or girth including preparation of new untreated surfaces complete all as specified and directed.

M&L for cable route indicator made up of precast RCC (1:2:4) type B1 (using 20mm graded stone aggregate) of size 300mm wide and 800mm height and 100 mm thick, install the same on ground by PCC works 1:3:6 Type C1 (size 310mmx150mmx300mm), engraved the words in capital letters of size 5cm height and 2cm width "FIRE OFC CABLE" or FIRE OFC JOINT" including rendering 10mm thick in CM (1:3) and two coats of weather coat paint over a coat of primer etc complete all as directed. Note : Installation of route indicator through earth & PCC works shall be measured and paid separately.

M&L for dismantling of ACSR or AAC conductors of any sizes or types etc. complete and setting aside for taking credit complete all as specified & directed.

M&L for dismantling the insulators of any any types or sizes complete all as specified & directed.

M&L heavy duty round wire armoured LT under ground cable 35Sqmm, 3.5Core, 1100 V grade HR PVC insulated , HR PVC inner & outer sheathed ,multi stranded aluminium cable conforms to IS 7098/(Part-I) 1988 with latest ammendments in pipe /trench /cable duct /fixed on wall by proper size shaped GI clamps with nut bolts etc and making good the disturbed surfaces by cement mortar/paint to match with the existing incl. taking out old unsv one and deposting the same in MES store yard complete all as specified & directed. Make-PolyCab /RR Kable/ Havells

M&L heavy duty round wire armoured LT under ground cable 25Sqmm, 3.5Core, 1100 V grade HR PVC insulated , HR PVC inner & outer sheathed ,multi stranded aluminium cable conforms to IS 7098/(Part-I) 1988 with latest ammendments in pipe /trench /cable duct /fixed on wall by proper size shaped GI clamps with nut bolts etc and making good the disturbed surfaces by cement mortar/paint to match with the existing incl. taking out old unsv one and deposting the same in MES store yard complete all as specified & directed. Make-PolyCab /RR Kable/ Havells

M&L heavy duty round wire armoured LT under ground cable 16 Sqmm, 4.0 Core, 1100 V grade HR PVC insulated , HR PVC inner & outer sheathed ,multi stranded aluminium cable conforms to IS 7098/(Part-I) 1988 with latest ammendments in pipe /trench /cable duct /fixed on wall by proper size shaped GI clamps with nut bolts etc and making good the disturbed surfaces by cement mortar/paint to match with the existing incl. taking out old unsv one and deposting the same in MES store yard complete all as specified & directed. Make-PolyCab /RR Kable/ Havells

M&L heavy duty round wire armoured LT under ground cable 10Sqmm, 4.0Core, 1100 V grade HR PVC insulated , HR PVC inner & outer sheathed ,multi stranded aluminium cable conforms to IS 7098/(Part-I) 1988 with latest ammendments in pipe /trench /cable duct /fixed on wall by proper size shaped GI clamps with nut bolts etc and making good the disturbed surfaces by cement mortar/paint to match with the existing incl. taking out old unsv oneand deposting the same in MES store yard complete all as specified & directed.Make-PolyCab /RR Kable/ Havells

M&L heavy duty round wire armoured LT under ground cable 10Sqmm, 2.0Core, 1100 V grade HR PVC insulated , HR PVC inner & outer sheathed ,multi stranded aluminium cable conforms to IS 7098/(Part-I) 1988 with latest ammendments in pipe /trench /cable duct /fixed on wall by proper size shaped GI clamps with nut bolts etc and making good the disturbed surfaces by cement mortar/paint to match with the existing incl. taking out old unsv oneand deposting the same in MES store yard complete all as specified & directed.Make-PolyCab /RR Kable/ Havells

Supply & use of corrosion inhibiting compound during fixing the cable end in aluminium reducer terminals or any other specified location all as specified and directed.

M&L for boring under roads or any other specified location by reqd T&P without disturbing the top surface of the road for insertion of GI Pipe etc complete all as specified and directed.

M&L for tubes 50 mm bore light grade galvanized with all fittings laid in trenches/ wall/ pole through MS flat (25X3 mm), nut, bolt & washers [ as reqd ] of proper sizes for protection cables complete all as specified and directed. Make- Nezone/ Bansal/ Jindal

M&L for fixing the aluminium reducer terminal in cable end (through corrosion inhibiting compound) of cable size 35 sqmm all as specified & directed. Note: Corrosion inhibiting compound which will be used during crmping of reducer terminal shall be measured and paid separately.

M&L for fixing the aluminium reducer terminal in cable end (through corrosion inhibiting compound) of cable size 25 sqmm all as specified & directed. Note: Corrosion inhibiting compound which will be used during crmping of reducer terminal shall be measured and paid separately.

M&L for fixing the aluminium reducer terminal in cable end (through corrosion inhibiting compound) of cable size 16 sqmm all as specified & directed. Note: Corrosion inhibiting compound which will be used during crmping of reducer terminal shall be measured and paid separately.

M&L for fixing the aluminium reducer terminal in cable end (through corrosion inhibiting compound) of cable size 10 sqmm all as specified & directed. Note: Corrosion inhibiting compound which will be used during crmping of reducer terminal shall be measured and paid separately.

M&L for fixing the aluminium reducer terminal in cable end (through corrosion inhibiting compound) of cable size 6 sqmm all as specified & directed. Note: Corrosion inhibiting compound which will be used during crmping of reducer terminal shall be measured and paid separately.

M&L for fixing the cable junction boxes of size 225 x 295 x 122 mm, with terminals for 35sq mm, 3.5 C, 1100V cable, IP 66/69, weather proof, outdoor installation type with threaded cable glands & pole mounting brackets etc complete all as specified & directed. Make- Hensel / OBO

M&L for fixing the cable junction boxes of size 205 x 255 x 112 mm, with terminals for 10 - 25 sq mm, 4.0 /3.5 C, 1100V cable, IP 66/69, weather proof, outdoor installation type with threaded cable glands & pole mounting brackets etc complete all as specified & directed. Make- Hensel / OBO

M&L for making two nos hole for throughing 1.5sqmm,3 single core, 1100V cable with in steel tubular swaged pole of type SP 31/ 55 through drill or other reqd T&P complete all as specified and directed.

M &L for 3 single core PVC insulated multi stranded copper conductor cable 1.5 sq mm 1100V unarmoured for connection from loop /junction box to street light / security light complete all as specified and directed.

M/S PANKAJ SUPPLY SYNDICATE

Arpara Trade Agency

PURBANCHAL BUILDERS

Swastika Engineers and Agencies

M/s Vishnu Enterprises

M/s Capital Traders

M/s JRS Associates