PROVN OF LIVING ACCN WITH ATTACHED TOILET AND BATHROOM FOR TWO NCOS AND SIX OR AND SPL REPAIR OF BLDG NO PP 02/01 AND PP 02/02 AND OTHER SANCTIONED WORK UNDER AGE BR II AT CITY AREA ALWAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) & removing unserviceable materials in low laying area complete all as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area complete all as directed.

Demolition of mud phuska in roof any thickness including plastering & leeping (whether full thickness removed or only part thereof) in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.

Dismantling & taking out old unserviceable 75mm bore PVC pipe with fittings laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

Dismantling & taking out old unserviceable 110mm bore PVC pipe with fittings laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface complete all as specified and directed.

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified and directed by Engr-in-Charge. Note : Removing of vegetation / shrubs / brushwood / undergrowth and carrying away rubbish to a distance of 50 m deemed to included in quoted rate.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft / loose soil.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, laying of cables, pipes etc not exc 10Sqm on plan and not exc 1.5m in depth and getting out in soft / loose soil.

Excavating in trenches not exc 1.5m wide and exc 1.5m but not exc 3.0m in depth; for foundation, etc or for shafts, wells, cesspits, manholes etc not exc 10Sqm on plan and not exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified& directed.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. Note :- Soil obtained from excavation under item 2.00 here-in-before shall be used for filling.

M&L for anti-termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the substructure in contact with backfill to be measured) complete all as specified and directed by Engr-in-Charge.

M&L for anti-termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engr-in-Charge.

M&L for anti-termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engr-in-Charge.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1, using 12.5mm graded crushed stone aggregate as in copings and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified and directed.

M&L for cement concrete 1:3:6 type B1, using 20mm graded crushed stone aggregate as in bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to sides of Pillars, posts, struts piers, columns etc in squarre, rectangular or polygonal, rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to chajjas, chullah hoods, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded stone aggregate in lintels upto 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for mild steel round bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per description of serial item No. 42.00 here-in-above but 6 to 10mm dia in stirrups, spacers and binders.

All as per description of serial item No. 42.00 above but 6mm dia to 8 mm dia.

M&L for 100mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 25mm thick cement concrete, type B-1 (using 20mm graded crushed stone aggregate) as in subbase, levelling coarse for tiles etc finished fair & even complete all as specified and directed.

M&L for 40mm thick cement concrete, type B-1 (using 20mm graded crushed stone aggregate) as in subbase finished fair & even complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in benching to drain including finishing the top of benching even and smooth using extra cement Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars complete all as specified and directed.

Cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, including finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement plaster 1:6 on stone masonry surfaces or surface other than fair face of brick work of walls including finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls including finishing the surface fair and even complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified. Note : - Supply only water proofing admixture shall be measured and paid for separately.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kerb stone block (factory casted) with plain fair faces, including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes etc. including placing in position and set in CM (1:4) complete all as specified and directed. Note :- Reinforcement shall be measured and paid for separately.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Blank

M&L for coloured non skid ceramic tiles (1st quality), 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles (1st quality), 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

Blank

M&L for coloured glazed ceramic tiles (1st quality), 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

Blank

M&L for 18 to 19mm thick Udaipur Green marble (of any type) work as in platform etc,and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble including cutting, grinding and polishing including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for 20mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to achieve mirror finish complete all as specified. Note : Kota stone shall be brought at site in minimum size of 560 x 560mm.

M&L for machine cut Kota stone slab 20 to 25mm thick, as in in riser of steps, skirting, dado and pillars etc. set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over & including rendring of 10mm thick in CM 1:4 complete all as specified.

Blank

Supply only integral liquid water proofing compound (ISI marked). Make : Pidilite (Dr. Fixit Pidiproof LW) or equivalent of Fosroc / Sika / STP

M&L for 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, not exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4 incl Dismantling of old stone slab complete.

M&L for 15mm thick plaster over concrete surface in CM 1:4 mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified. Note : - Supply only water proofing admixture shall be measured and paid for separately.

S&F APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermo lay manufactured by STP Ltd of 'Hyper Plas' (Polyester) manufactured by M/s IWL Ltd or 'Shaliplas' (polyester) manufactured by M/s Capital Steels and chemicals Pvt Ltd or Hydro Stop manufactured by TIKITAR DANOSA (INDIA) Pvt Ltd as approved by GE, black finish reinforced with nonwoven polyester matt, with a thermo fusible finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/s STP Ltd or 'WMW FLATE' of M/s Texas India Ltd) at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufactures' instructions complete all as directed. Cont...

Cont... Note:- (i) Coved fillets in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75 mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the grove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. Cont...

Cont... (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminum paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other sections with gusset plates, rails, braces, etc., complete of Gde E-165 (Fe 290), drilled for fixing of steel sheeting or other covering (exclusive of steel sheeting or other covering) including necessary welding etc with & including framed portion hung as gates including pintle hinges, stops, hand made sliding bolts etc complete all as specified and as directed.

M&L in repair for mild steel cupboard shutter with frame, Godrej Pattern, made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12mm dia bolt 150 mm long grouted in brick wall/concrete including making good the disturbed surfaces as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

M&L Solid PVC single Door Frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

All as per description of serial item No. 81.00 but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S Solid tube and this tube shall be welded to M.S tubes. The wire gauge shall be stretched to tighten firmly

S&F factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified and directed.

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified and directed.

S&F anodized aluminium grill of approved pattern, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) for windows / ventilators / doors complete as directed and all as specified.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

S&F butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S&F aluminium handle 150mm size cast type, anodized complete all as specified.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

Supply only 4.8mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Blank

Supply only 5mm thick Sheet glass, frosted, on one side and glazing in square not exc 0.5 sq. m in each pane complete all as specified.

Supply only 4mm thick Sheet glass, frosted, on one side and glazing in square exc 0.5 sq. m in each pane complete all as specified.

S&F in repair stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified and directed.

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

Taking up or down 25mm bore steel tubing and connection incl cleaning for refixing or removal to store

S&F galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors with required size of flat iron (25mmx3mm) clamps complete all as specified and directed.

S&F galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors with required size of flat iron (25mmx3mm) clamps complete all as specified and directed.

S&F galvanised steel water tubing medium grade of 25mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors with required size of flat iron (25mmx3mm) clamps complete all as specified and directed.

M&L for galvanised steel water tubing medium grade of 15mm bore with & including all fittings complete laid in trenches. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts complete.

S&F in repair stainless steel Kitchen plate rack made of stainless steel 1mm thick of size 600mm x 900mm and 230mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed.

S&F vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device including making good to distrubed floor with PCC or cement mortar 1:3 to match with existing sorroundings complete all as specified and directed.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including making good to distrubed surfaces of floor to match with existing sorroundings complete all as specified.

S&F as in repair vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including making good to distrubed surfaces of floor to match with existing sorroundings complete all as specified.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white (ISI marked) of 10 litre capacity with inlet, ball valve, float and handle including brackets complete all as specified..

S&F as in repair PVC valveless, syphonic action type, flushing cistern, low level, white (ISI marked) of 10 litre capacity with inlet, ball valve, float and handle including brackets complete all as specified..

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including cutting for and pinning in ends of brackets or erecting stand, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed complete all as specified.

S&F as in repair vitreous china wash hand basin, white, flat back of size 450mm x 300mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and chromium plated waste coupling complete all as specified..

S&F as in repair pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

S&F brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed.

S&F 15mm bore stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair 20mm bore stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair 15mm bore stop / angle valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F 15mm bore stop / angle valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repair PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F brass chromium plated shower rose 125mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair brass chromium plated shower rose 125mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F stainless steel peg set of six fixed to wall with two rawl plugs and chromium plated (CP) brass screws complete all as directed.

S&F glass corner shelf of size 200mm x 200 mm, 6mm thick outer edges rounded fixed to wall with chromium plated brass brakets, screws and wooden / plastic plug complete all as specified and directed.

S&F as in repair tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed to wall complete all as specified and directed.

S&F towel rack, chromium plated, 60cm long between flanges fixed to wall complete all as specified and directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) all as directed.

S&F 20mm bore Gun metal gate valve with iron wheel head, screwed both ends for iron pipe copmplete all as specified and directed.

S&F as in repair PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F in repair PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F in repair 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal complete all as specified.

S&F in repair 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal with access door complete all as specified.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors including taking out old unserviceable PVC pipe with fittings and making good the disturbed surface as per existing complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking out old unserviceable PVC pipe with fittings and making good the disturbed surface as per existing complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F 75mm bore PVC (SWR) single junction (single ‘T’) equal or unequal complete all as specified.

Dismantling water tank of capacity exc 250 ltr but not exc 500 ltr and removing from site complete all as directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 15mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

M & L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

Blank

M&L for preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered / asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil emulsion distemper (OBD) of approved shade / tint over 1mm thick birla white wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint of approved shade / tint complete all as specified.

Blank

M&L for preparation of old plastered surfaces of walls & applying one coat of white wash complete all as specified.

M&L for preparation of old plastered surfaces of ceilings & applying one coat of white wash complete all as specified.

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of oil emulsion distemper (OBD) of approved shade / tint over 1mm thick birla white wall care putty complete all as specified and directed.

Taking down carefully, copper / aluminium unserviceable /perished point wiring any type for light/ fan/ socket or power complete including fittings such as switches, ceiling roses, pendant holders, lamp holders, bracket holders, regulators sockets, light fittings etc, and making good to disturbed surfaces of wall/floor/ceiling etc, complete, all as specified and directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS and including existing sunken boxes fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per description of serial item No. 169.00 above but for one fan point controlled by one switch

All as per description of serial item No. 169.00 above but for one bell/buzzer point controlled by one bell push

All as per description of serial item No. 169.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per description of serial item No. 169.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per description of serial item No. 169.00 here-in-before but for one 3 pin socket outlet 15/16 Amps with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS and including wooden boxes / MS Sunken box fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per description of serial item No. 175.00 above but for one fan point controlled by one switch

All as per description of serial item No. 175.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per description of serial item No. 175.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per description of serial item No. 175.00 here-in-before but for one 3 pin socket outlet 15/16 Amps with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin, 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5/6 & 15/16 Amp, flush type 240 Volt complete all as specified and directed.

S&F bell push flush type, 5/6 Amp 240 Volts complete all as specified and directed.

S&F elctric bell / buzzer, AC, 230 volts, single pole complete all as specified and directed.

S&F ceiling rose surface Bakelite 65x50mm two or three terminals complete all as specified and directed.

S&F fan regulators electronic step up type socket size and connecting up, ISI marked flush type, 240 volts complete all as specified and directed.

S&F decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube 6000K of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make :- Havells Cat Part No LHEXBLP7PN1W018 or equivalent of Syska / Crompton Greaves as approved by GE

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED blub / lamp of 10 / 11 Watt complete all as specified.

Supply and fixing LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make :- C&S Cat Part No LTESS20WLED or equivalent of Havells / Syska / CG as approved by GE

S&F sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F in repair sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 4 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 4 way, 240 volts complete all as specified and directed.

S&F in repair MCB 63 Amps, single pole & neutral, 240 Volts, C curve, 10KA rupturing complete all as specified and directed.

S&F in repair MCB 32 Amps, single pole & neutral, 240 Volts, C curve, 10KA rupturing complete all as specified and directed.

S&F MCB 32 Amps, single pole & neutral, 240 Volts, C curve, 10KA rupturing complete all as specified and directed.

S&F in repair MCB 6 to 32 Amps, single pole, 240 Volts, C curve, 10KA rupturing complete all as specified and directed.

S&F MCB 6 to 32 Amps, single pole, 240 Volts, C curve, 10KA rupturing complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30x25x5 cm depth with 3mm thick hylum/Bakelite sheet on top grouted with 4 Nos bolts for DB complete all as specified and directed.

Disconnecting & taking down carefully existing ceiling fan / exhaust fan / geyser of any capacity / make / size and depositing the samein AGE E/M store yard complete all as specified & directed.

M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cables, drawn through & including suitable size of heavy duty PVC conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed on surfaces of wall/ceiling including taking down old unserviceable wiring complete all as specified and directed. Note:- 02 runs of 6 sqmm size, 01 run of 6 sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose.

S&F 1100 Volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of aluminium stranded conductors of size 10 Sqmm all as specified & directed

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

All as per description of serial item No. 204.00 above but for cross sectional area 16 sqmm 2 core

All as per description of serial item No. 204.00 above but for cross sectional area 25 sqmm 4 core

M & L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (Tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L for Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete.

Cutting of existing 50 mm bore GI pipe and inserting Tee, Elbow, Bend / Collar and tapping for jointing or making branch connections

S&F ceiling fan 1200 mm sweep suitable for 240 Volts, 50 Hz, AC supply with down rod & canopy including provision of fan hook in ceiling for fixing of ceiling fan including necessary electric connection with 1 Sqmm, three core, flexible copper multistranded conductor cable complete all as directed.

Supply & fixing and testing exhaust fan of 300mm sweep suitable for 240 Volts, 50 Hz, AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers complete all as directed.

S&F PVC body, desert coolar, electric driven, single phase having nominal air flow capacity 5000 Cum/hour complete all as specified & as directed. Note - (i) The desert coolar with I-Pure techonology which has a dust filter, smell filter, allergy filter to give clean and healthy air. The coolar is equipped with high efficiency honeycomb pads that provide superior cooling. (a) Tank capacity 75 ltr. (b) Cool flow dispenser. (c) Fan Motor 3speed copper winding. (d) One year manufacture warranty. (ii) Make - Symphony sumo 75 XL 75L desert air coolar (white) or equivalent model of Havells / Cromton as approved by GE.

Supply, installation & testing Geyser (water storage type) of capacity 25 litre, Star rated suitable for 240V, SP, 50 Hz AC supply fixed with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of 10mm dia 150mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original all as per manufacturer’s instructions & as directed. Make :- Bajaj / Crompton Greaves / Usha Lexus / Venus / Racold.

Material and labour for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on cont...

cont.... including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete including taking down old unserviceable earthing all as specified & as directed.

M/S SHEODAYAL GUPTA

UNIQUE INDIA CONSTRUCTIONS