Special repair of Sub Health Centre at Village Pingor in Palwal Distt. Re-Tender

Amount

Civil & P.H. Works

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 Mtrs. (HSR 6.6)

Dismantling Concrete reinforced cement concrete with cleaning and straightening and cutting of bras if requried. (HSR 8.6 e)

Cement concrete 1:8:16 with stone aggregate 40 mm Nominal site in foundation and plinth. (HSR 10.28)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size in First Storey upto 4 metres abvoe plinth level (HSR 10.59)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)].

First class brick work laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

First class brick work laid in cement sand mortar 1:6 in 1st storey upto 4 metre above plinth level. (HSR 11.7)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 Meter above plinth level ( HSR 11.7)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Conglomerate floor 40 mm thick Cement Concrete topping 1:2:4. (HSR 14.9)

Floating cost of 1.50mm thicmk neat cment laid in one operation to the topping (HSR 14.3)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. Digital Print tiles of Size of 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used. [HSR 14.92(b)].

Terracing consisting of tiles 22.86 x 11.43 x 3.81cm. laid over 87.50 mm. mud filling on a layer of 25 mm. mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg. per Sqm. on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc.(HSR 13.13)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC pipe 6 kg. pressure.

12mm thick cement plaster on walls (1:6). (HSR 15.7).

15mm Thick Cement Plaster 1:6 on the rough side of single or half brick wall. (HSR 15.12).

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52).

Cement rendering on plaster 1 mm thick.(HSR 15.75)

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3). Through Rate

Painting one coat with synthetic enamel Paint in all shades on old wood-work, or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.7). Through Rate

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge).(HSR 16.58).

Providing and Applying Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)]

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81). Through Rate

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screw, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 30 mm thick. [HSR 17.90 (a) - Note 1 under 17.18].

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (i) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (c) decorative veneering with vertical grain cross bands and face veneer on both sides teak facing and edges lipped with commercial hard wood with laminated core:- Duro, Green Only. [HSR 17.93 - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (iii) (HSR 17.93a iii

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of of RCC including straightening, bending , binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/ storeys/basements etc. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shaal not be measured and cost of these items shall be deemed to be included in the rates for reinforcement (HSR 18.22).

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (b) Size 630 mm (ii) Single Colour. (Make Hindware) (HSR 30.2 b ii)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (HSR 30.12) (i) white

Providing and fixing in position best Indian make flat back or angular lipped front urinal 465 mm high consisting of :-(HSR 30.19i) Flat back lipped or angular urinal basin of vitreous china ware (to the approval of Engineer-in-charge)5 liters capacity mosquito proof Indian make C.I automatic flushing cistern, painted with non-yellow white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15mm pipe.Pair of R.S or C.I painted brackets and brass couplings Standred size G.I flush pipe with C.P brass wall clips and unions complete including cutting and making good the walls and floor and painting o fittings etc (as required by the Engineer-in-charge)i)White

Providing and fixing 25mm thnick marble partitions for different type of urinals (HSR 30.40) (B) (II) (i) vetreous Chinaware Partition plate

Providing and fixing in position best India make towel rails fixed in with rawlslugs embedded in walls with CP Brass screws, Complete in all respect including cutting and making goods the walls etc. (HSR 30.68) (d) CP Brass Two swivel towel rail 400mm longh

Providing and fixing in position best Indian make Soap dis fixed into wall with C.P. brass screws and complete in all respects including cutting and and making goods the walls etc (HSR 30.70) (d) Vitreous Chinaware recessed soap dis with hand rails (iii) Mixed Colour

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc (HSR 30.71)

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (a) Bib cock long body (HSR 30.75)

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) a) 15mm stop cock(HSR 30.76) i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully decribed in item no 30.41 above (HSR 30.42)R.S or C.I brackets for building into wall including painting32 mm C.P brass waste with C.P brass chain and rubber plug15 mm C.P brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-charge)All fittings best Indian make and; to the approval of the Engineer-in-chargeAll brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc.Size 530mmx430mm with one no. tap

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. 1000 Ltr. Cap. (HSR 30.119)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal Work - Exposed on Wall. [DSR 18.10). (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

(iii) 25 mm internal diameter of pipeline

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) (b) 20 mm nominal bore

(c) 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

Earth filling under floors / road and parking with tibba sand non plastic under floors with good earth taken from outside of campus area with all lead and lift including loading, unloading, laid in 15cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. (For any lead lift). (NS items).