SPECIAL REPAIR TO BUILDING, CONSTRUCTION OF OPEN PLINTH, PROVN OF SIGN BORD AND CERTAIN REV AND MINOR WORKS UNDER AGE BR-V AND AGE EM-V OFFICE OF GE NORTH BATHINDA

Amount

Surface dressing not exceeding 15cm deep in soft/ loose soil including cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cutting and dressing and removing from site all grass, roots and extra soil if any complete all as specified and as directed by Engineer-in-Charge.

Excavation in post holes in soft/loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by Engineer-in-Charge.

Excavation over areas, not exceeding 1.5mtr deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation over areas, exceeding 1.5mtr and not exceeding 3mtr deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation over areas, exceeding 3mtr and not exceeding 4.5mtr deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation over areas, exceeding 4.5mtr and not exceeding 6mtr deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-charge.

Returning and filling including spreading, leveling watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Labour for earth filling under floor/plinth, around soakwell, removing, spreading, levelling in layers n exc. 25 cm thick (each layer) consolidating the surface with Durmat/hand roller, rolling to required gradient and camber and upto entire satisfaction of Engineer-in-charge including levelling, well ramming including watering as required and consolidation complete all as specified and directed by Engineer-in-Charge. Note :- Extra Earth obtain form excavation shall be re-used.

Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (surplus soil) to a distance exceeding 250 m but not exceeding 500m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour for Loose filling with broken bricks aggregates of gauge 40 to 80 mm in soakage pits, soakage wells complete all as specified & directed by Engineer-in- charge.

Material and labour for hard core of broken bricks of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge.

Material and labour for hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge.

Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in flooring, hard standing, plinth protection/path etc. finished even and smooth without using extra cement including sweeping cleaning and washing existing surface before PCC laying complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 50 mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in flooring, hard standing, plinth protection/path etc. finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base of floor, under paving, plinth protection, under interlocking tiles etc over rammed earth/hard core complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC (1:2:4), type B-1 using 20 mm graded stone aggregate as in foundation filling and mass concrete, bed block, for embedded posts & similar work etc complete all as specified and as directed by Engineer-in-charge.

Material and labour for 100mm thick cement concrete ( 1:2:4), type B-1 using 20 mm graded stone aggregate as in floor, hardstanding/paving/path etc, in panels size as directed with provision of expansion joints and including mixing fibre 12mm recron 3s @ 900gms/cum of cement concrete, surface finished even & smooth without using extra cement including necessary form work complete all as specified and as directed by Engineer-in-charge. NOTE : (i) Filling of expansion joints shall be measured and paid separately under appropriate item of BOQ. (ii) Recron 3s shall be measured & paid separately as Supply only

Material and labour for forming 12mm thick expansion joints (thickness of concrete slab 100mm ) filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'B' including cutting extra concrete as required complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40 mm thick damp proof course in cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary form work and using water proofing compound complete all as specified and as directed by Engineer-in- charge. (Note :- Water proofing compound shall be measured & paid separately as Supply only)

Material and labour for antitermite treatment, treating the bottom and sides of excavation at the rate of 5.0 Litres of emulsion per square metre of surface area complete all as specified & directed by Engineer-in- charge.

Material and labour for antitermite treatment, treating the backfill in contact with foundation at the rate of 7.5 Litres of emulsion per square metre of vertical surface (area of substructure in contact with backfill to be measured) complete all as specified & directed by Engineer-in- charge.

Material and labour for antitermite treatment, treating the top surface of filled earth at the rate of 5.0 Litres of emulsion per square metre complete all as specified & directed by Engineer-in- charge.

Material and labour for antitermite treatment, treating the soil under plinth protection at the rate of 5.0 Litres of emulsion per square metre complete all as specified & directed by Engineer-in- charge.

Form work to sides and soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs, sides of chajjas etc and similar works rough finished flat surfaces complete all as specified & directed by Engineer-in- charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick (horizontal or sloping) rough finished complete all as specified and as directed by Engineer-in- charge.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide, rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers., lintels upto 1.5 mtr span complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers., lintels over 1.5 mtr span complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed by Engineer-in- charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose)

Material and labour for mild steel work as in rungs, hooks, rings for steps, handles of manhole covers, hold fast and small articles complete all as specified and directed by Engineer-in-Charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work in half brick thick wall using burnt clay bricks (sub class 'B' old size burnt clay bricks) straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed by Engineer-in- charge.

Material and labour for brick work using sub class 'B' old size bricks in brick-on-edge walls (less than ½ brick thick), built in cement mortar (1:4) complete all as specified & directed by Engineer-in- charge.

Material & labour for continuous brick edging (sub class ‘B’) with width equal to the width of brick laid dry on end vertically including necessary earth work, embedding bricks at depth as indicated and temping around bricks and removal of surplus soil to a distance not exceeding 50 metre and depositing where directed complete all as specified. Note : Each row shall be measured and paid separately.

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces including mixing of WPC in mortar @ 3% of cement content and mixing fibre 6mm recron 3s @ 125gms/bag of cement of 50Kg, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. (Note :- Water proofing compound and recron 3s shall be measured & paid separately as Supply only)

Material and labour for rendering/plastering 10mm thick in cement mortar (1:4) on any face of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Supply only integral water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

Supply only recron 3s type CT 2024, 6mm/12mm complete all as specified and as directed by the Engineer-in-Charge. Make :- Reliance /Swastic /Fosroc or equivalent (Equivalency approved by GE)

Roughening surfaces of old concrete floor by picking and prepare the surface to receive the screed for tiling, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by Engineer-in-Charge.

Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from the site to a distance not exceeding 100 metre and deposited as directed complete all as directed by Engr-in-Charge

Material and labour for Glazed ceramic coloured tiles 7 to 8mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surface such as skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (rendering) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade, jointless) 8 mm thick square or rectangular area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (dark shade, jointless) 8 to 10 mm thick square or rectangular area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (dark shade, jointless) 8mm to 10mm thick square or rectangular (same as floor tile, as per above item ), as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (dark shade, jointless) 8 to 10 mm thick square or rectangular area of each tile exceeding 0.42 sqm but not exceeding 1sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs etc all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames, wooden/PVC doors) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out 5mm thick plain clour PVC sheet reinforced with MS square tube including painting of edges to match with sheet, all as specified & shown in relevant drawing of item No. 8095 in MES Schedule SSR-2010 (Part-II), fixed in opening complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made solid core PVC door shutter 30mm thick (stiles) consisting of frame made out of MS tubes of 19mm gauge thickness and size of 19mmx19mm for stiles and for top and bottom rails 15mmx15mm. MS frame shall have a coat of red oxide primer of approved make and shall be covered with heat moulded plain colour PVC sheet, 'C' channel of size 30x50mm forming stiles and 5mm thick wide PVC sheet strip of 20mm width stuck inside with solvent cement for stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and 10mm (5x2mm) thick, 20mm thick PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side and joined together with solvent cement adhesive and an additional 5mm thick PVC strips of 20mm width is to be stuck on interior side of C channel using PVC solvent adhesive as per manufacturer's instructions, door to be fixed to frame with and including 3 Nos MS powder coated butt hinges of size 100mm long x 25mm wide and 2mm thick and 32mm long steel screws drilled suitable to pass through both the walls of the MS tube complete all as specified in SSR-2009 (Part-I, specifications) & shown in relevant drawing of item No. 8080 in SSR-2010 (Part-II, rates). The width of stiles & rails will be in proportion to the width of the door shutter as specified in SSR-2010 (Part-II). complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing, factory made steel ventilators all as per IS 1038/83, with top hung shutters including hinges, suitable steel handle, steel peg stay, fixing lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) complete all as specified & as directed by Engineer-in- charge.

Supply & fixing, factory made steel ventilators all as per IS 1038/83, with top hung shutters including hinges, suitable steel handle, steel peg stay, fixing lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including taking out old rusted broken ventilator any type including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast and making good disturbed area of walls and cills to match the existing surfces by bricks/plastering works and painting work etc complete all as specified & as directed by Engineer-in- charge.

Supply and fixing in replacement mild steel handle (left/right side as per demand) ready made suitable for steel window (z section) as per existing size and shape including nut & bolts with washer complete all as specified and as directed by Engineer-in-charge.

Supply & fixing aluminium anodised frame, made out of aluminium section weighing 0.98 Kg/mtr, , powder coated (minimum thickness of powder coating not less than 50 micron), for doors, windows, ventilators with one or more rebate including jointing cleat for fixing etc. including taking down old unserviceable frame complete all as specified and directed by Engineer-in-Charge. Note :- If aluminium section used other than above mentioned weighing then weight of each section shall be physically ascertained through a board of officers convened by Accepting officer and payment shall be made only after the actual weight at site.

Supply & fixing anodised aluminium door shutter, made out of aluminium section weighing 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, suitable size of aluminium handles 2 Nos and aluminium hinges 03 Nos in each door (size of handle and hinge as directed), anodised aluminium snap beading, screws etc including taking down old unserviceable door shutter incl fitings and glass complete all as specified and directed by Engineer-in-Charge. Note :- Aluminium chowkhat frame and glass shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engineer-in-Charge.

Supply and fixing anodised aluminium handle cast type 100mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 125mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 100mm long complete all as specified & directed by Engineer-in-charge.

Supply & fixing, 3mm thick figured glass pin head type in squares not exceeding 0.5sqm in each pane for steel or wooden doors/wondows including fixing material complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement stainless steel chromium plated pipe 25mm dia, wall thickness of pipe not less than 20 guage, as curtain rod fixing with and including fancy type brackets and decorated end knobs (finials), stop roller etc, fixed on wall for doors and windows curtains, cuttings as required length and fixing at site including fixing arrangements, rawl plug, screws etc. including taking out old any type rod or pelmet boxes with curtain rod complete all as specified & directed by Engineer-in- charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and Supply & fixing new 4mm thick sheet glass ordinary quality in squares not exceeding 0.5sqm in each pane and fixed in any type of doors/windows/ventilators with wooden bead/pin tacked/with oil putty etc. as required or as directed including cutting of glass as per site requirement complete all as specified & directed by Engineer-in- charge.

Supply & fixing, 4mm thick sheet glass ordinary quality in squares exceeding 0.5sqm in each pane and fixed in aluminium section complete all as specified & directed by Engineer-in- charge.

Supply & fixing, solar control film 25 micron reflective type (gareware sun control or equivalent) pasting on glass duly air bubble free complete all as specified & directed by Engineer-in- charge.

Supply & fixing aluminium (extruded section) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, ISI marked complete all as specified & directed by Engineer-in-charge.

Supply & fixing mild steel 4 lever mortice lock vertical type 100mm size with original and duplicate key complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor etc. for re-fixing or removing from site/keeping aside for reuse complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall/ceiling/floor etc. for re-fixing or removing from site/keeping aside for reuse complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting of existing pipe any dia for insertaion of tee branch as required for connection complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting of existing pipe any dia for insertaion of tee branch as required complete all as specified and as directed by Engineer-in- charge.

Dismantling cast iron drain pipes, jointed in cement mortar of any description any dia from wall and taking out from trenches including all fittings (bend, trap, cowl, branch piece etc) and removing from the site complete all as directed by Engr-in-Charge.

Material & Labour for 100 mm bore cast iron soil waste and vent pipe (sand cast pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 100 mm bore cast iron soil waste and vent pipe (sand cast pipe ) in any length with or without ears, laid in trenches or in floor jointing with cement mortar complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 75 mm bore cast iron soil waste and vent pipe (sand cast pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 75 mm bore cast iron soil waste and vent pipe (sand cast pipe ) in any length with or without ears, laid in trenches or in floor jointing with cement mortar complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) without oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door complete all as specified & directed by Engineer-in- charge.

Supply and fixing Cast iron floor trap 100mm bore, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints as specified & directed by Engineer-in- charge.

Supply & fixing 75mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door complete all as specified & directed by Engineer-in- charge.

Supply and fixing Cast iron floor trap 75mm bore, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore cast iron cowl complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore cast iron cowl complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with stack clamps made out of FI 50x5mm and 16mm dia round iron stay (suitable Nos i.e interval of 1m ) complete all as specified and as directed by Engineer-in- charge.

Supply & fixing PVC (SWR) bends (any radius) suitable for 110mm bore pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 150mm x 150mm size salt glazed stone ware gully traps, square or round mouthed, type 'P' complete all as specified and as directed by Engineer-in- charge.

Material and labour cutting into existing manholes/septic tank for connecting new drain 100mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round to 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished, and reforming benching as required complete all as specified & directed by Engineer-in-charge.

Material and labour for 150mm bore (internal dia) salt glazed stone ware (SGSW) drain pipe, grade ‘A’, laid on concrete bed to required slope in trenches, jointing with packed spun yarn and in cement and sand mortar (1:1) and tested complete all as specified and directed by Engineer-in-Charge. (Note : Concrete bed shall be measured and paid for separately)

Material and labour for cement concrete (1:4:8), type D2 using 40mm graded stone aggregate as in bed of drain pipe (SGSW) of size 150mm bore (internal) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in- charge.

Supply and fixing single piece WC of size 655x365x755mm with UF seat cover, hinges, fixing accessories set, cistern fittings, P-trap 180mm, including connection to drain including taking out/down old WC with fittings complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part LYS-WHT-38851P of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in replacement vitreous china wash down water closet pan (pedestal pattern, EWC) white clour (excluding flushing cistern and flush pipe) including connection to drain and to flushing pipe anti syphonage etc., including plastic water closet seat with cover (white clour) closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including stainless steel chromium plated jet spray with 01 mtr long PVC pipe with CP connector and necessary nut bolts and with necessary CP screws and plug for fixing WC complete all as specified and as directed by Engineer-in- charge.

Supply and fixing hand shower (health faucet) ABS body including 1 meter long 8mm dia flexible tube and including wall hook complete, all as specified and as directed by Engineer-in-charge. Make :- Cat Part ALD-CHR-593N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in replacement vitreous china urinal, half stall type, white, including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, 32 mm dia full threaded PTMT waste coupling and 32mm dia waste pipe and pointing around urinal back in cement mortar, including Urinal spreader of stainless steel, PVC connection pipe suitable for fixing with 15 mm dia pipe/valve including taking down old urinal with fittings complete all as specified & directed by Engineer-in-charge.

Supply & fixing vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm white with integral foot rests (excluding flushing cistern and flush pipe ) but including CI 'P' or 'S' trap set in and including lime concrete bed for trap and under WC, including PVC pipe upto finished floor level to connect flush pipe, complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 10 litres capacity PVC valveless syphonic action type low level flushing cistern (white colour) with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern (white colour) with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement vitreous china wash hand basin white colour, flat back of size 590mm x 420mm x 195mm excluding taps, but including fancy type 32mm waste coupling and waste pipe, fixing/counter sunked in granite slab, including taking out any type WHB with fittings complete all as specified and as directed by Engineer-in-Charge. Note :- Granite slab shall be measured and paid separately under appropriate item of BOQ. Make :- Cat Part CNS-WHT-705 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Material and labour 20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour as in steps, jambs, pillars, window-cills, cooking platforms, counter sunk wash basin plateform and like or as directed, including screed bed 15mm thick in cement mortar (1:4) (grey cement slurry) including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and directed by Engineer-in-Charge.

Supply & fixing vitreous china wash hand basin white colour, flat back of size 450mm x 300mm excluding taps, but including 32mm waste coupling and waste pipe (LDPE), including new bracket and cutting for and pinning in end of bracket or erecting, complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement stainless steel chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to wall with bracket with chromium plated brass screws and PVC plug complete, all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement MS chromium plated, soap tray approximate size 160x160mm, including fixing to wall with CP screws and PVC plug complete all as specified and directed by Engineer-in-Charge.

Supply and fixing bib tap cast copper alloy, chromium plated, fancy type with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply & fixing Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts screwed for iron pipe or for brass ferrule 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply & fixing 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply and fixing gun metal, globe or gate valve (ISI marked), with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement stop valve/angle valve cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock/angle valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply and fixing in replacement bib tap cast copper alloy, chromium plated fancy type, long body with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing pillar tap cast copper alloy with capstan head, chromium plated, fancy type high pressure with or without letter 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply and fixing pillar Cock (Ornamix Silver Brass Basin Tap) fancy type screwed down, high pressure suitable for iron pipe or for brass ferrule 15mm bore complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ORM-10001 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing Soap Dish Holder with bracket and flange including taking down old any type soap tray complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ACN-1131N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing liquid soap dispenser with glass bottle, fixed on wall with chromium plated brass screws and PVC plug including taking down old any type despenser complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ACN-1135N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing Glass shelf 600mm long including taking down old any type shelf complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ACN-1171N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in replacement 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply and fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical double layered with closed top), hoisted and fixed in position including out let connection complete all as specified and as directed by Engineer-in-charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical double layered with closed top), hoisted and fixed in position including out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description and capacity complete all as specified and as directed by Engineer-in-charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 1000 litres (cylindrical vertical double layered with closed top), hoisted and fixed in position including out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description and capacity complete all as specified and as directed by Engineer-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodised aluminium snap grid frame work of size of grid 605 x605mm for false ceiling including necessary notching and prepared holes, the snap grid shall consist of anodised aluminium main tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM, cross and Intermediate tee of size 23.5mm x 26.4mm x 1.4mm weighing 0.191 Kg/RM. The main and cross tee shall be jointed at junction with steel screws or MS bolts, nuts and washers, the snap grid (main / cross tee sections) shall be supported at ends all along the wall with anodised aluminium angle of size 35mm x25mmx 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and duly suspended with 4mm GI wire hangers (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 12mm thick gypsum board in grid fixed in false ceiling grid made of aluminium as per above specifications complete all as specified and as directed by Engineer-in-charge.

Supply and fixing solid PVC sheet wall lining (paneling) consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturers specifications and as directed) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 5mm thick, 35mm wide PVC fillet frame (under/top/bottom/corner side of paneling as per manufacturers specifications and as directed) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, L- type or J -type hooks or cranked bolts and bitumen washer or fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick including ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or fixed with L type or J type or cranked hooks bolts complete all as specified and as directed by Engineer-in-charge.

Material and labour for mild steel rolled sections framed work, framed/truss work for fixing GI sheets (design for framing as directed by Engineer-in-charge) and using angle, tee or other section with web and flange cut to shape, drilled and counter sunk for screw, as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, gusset plates, brackets, bending and welding, riveting etc, conforming to Gde Fe-410-W (Gde E-250 quality A) complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for mild steel work tubular trusses, poles/post including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to latest relevant IS grade St-240 complete all as specified & directed by Engineer-in- charge.

Dismantling brick tiles or terracing tiles single layer in roof laid dry and pointed in cement mortar, including cleaning and stacking serviceable brick tile for re use and balance removing/disposal off from the site complete all as specified and as directed by Engineer-in-charge.

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part there of) including cutting or uprooting grass, vegetations and roots of small plants etc on roof floor and surrounding, removing/disposal of retrived materials from site to a distance not exceeding 100 metre and deposited as directed complete all as directed by Engr-in-Charge

Material and labour for cleaning the roof screed surface including flashing and junction of parapets etc. by brushing, removing all dust and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per Sqm complete all as specified and directed by Engineer-in-Charge.

Supply and laying Polythene film, 150 micron thick, double layers, laid on and including a coat of bitumen primer @ 0.30 to 0.50 kg per sqm, joints proper locked with overlap complete all as specified and as directed by Engineer-in-Charge

Material and labour for 80mm thick average consolidated thickness mud phuska on flat roofs prepared with wheat straw and cow dung and lay properly including leeping mud plaster on roofs complete all as specified and as directed by Engineer-in-charge.

Material and labour for 40mm thick brick tiles laid on mud mortar & joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement and including flush pointing in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for 40mm thick brick tiles (old serviceable tiles obtained from demolition/dismantled item shall be reused) laid on mud mortar & joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement and including flush pointing in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC (1:2:4), type B-1 using 20mm graded stone aggregate as in coping, roof kerb or mud stops, rounded or chamfered on edges, side of roof sheet & similar work etc complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying two coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing newly plastered or concrete surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of new plastered surface of walls/pillars/cornices by brooming down with using broom/sand papering or by any other mean and preparing the surface smooth, applying one coat of chalk whitening as priming coat and after that applying two coats of weather proof exterior emulsion paint (Apex paint/wheather coat, 100% exterier grade), as per existing or as approved tint/colour complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment (any layers of existing treatment ) from walls/pillars/cornices by scraping down with using mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down and preparing the surfaces smooth and after that applying two coats of weather proof exterior emulsion paint (wheather coat Apex, 100% exterier grade) by using paint roller brush or electric paint spray machine, as per existing or as approved tint/colour complete all as specified and as directed by Engineer-in-Charge. NOTE : - Complete removal /scraping to old existing treatment as directed by Engineer-in-charge, each stage i.e after complete removal and before applying weather coats as specified above, the surface shall be passed in writing by the Enigineer-in-charge.

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by remove / scraping down all smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean upto entire satisfaction of Engineer-in-charge and after preparing the surface smooth applying one coat of lime white wash with using paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of ceiling by remove / scraping down all smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean upto entire satisfaction of Engineer-in-charge and after preparing the surface smooth applying one coat of lime white wash with paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment (any layers of existing treatment ) on walls/pillars/cornices by scraping down with using mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down and preparing the surfaces smooth by applying chalk whitening, preparatory to distempering and after that applying two coats of oil bound distemper (washable) as per approved tint/colour by using electric paint roller or roller brush complete all as specified and as directed by Engineer-in-Charge. NOTE : - Complete removal /scraping to old existing treatment as directed by Engineer-in-charge, each stage i.e after complete removal and before applying OBD as specified above, the surface shall be passed in writing by the Enigineer-in-charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour by using paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Supply, fabrication and fixing Fully retro-reflectorised cautionary, mandatory and informatory sign board of size 90cm equilateral triangle shape as per IRC: 67-2012 made of high intensity grade sheeting vide clause 801.3 of MORTH specification, frame made out of mild steel angle iron 75mmX75mmX6mm, sign board made by using aluminium sheet 1.5mm thick fixed over angle iron frame, sign board supported on 3m high (2.4m above ground and 0.60m below ground) post made out of 100mm dia Medium Grade MS Pipe confirming to IS 1161-1979 of Grade Fe 410, leg/post embedded in PCC block of size 45cm x 45cm x 60cm in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including necessary excavation and earth work complete all as shown and specified in drawing, aluminium sheet to be covered with high intensity grade retro-reflective sheeting as per IRC standard (AVERY DENNISON) blue/green or as required colour pasted firmly without appearance of bubbles and after that writing/pasted a computer cut letters or sign's of appropriate sizes made from retro reflective tape (High Intensity Prismatic Reflective Sheeting) including two coats of water-based acrylic polyurethane enamel paint on MS surfaces over a coat of red oxide primer. Complete all as per technical specifications and as directed by the Engineer-in-charge. Note:- All other details specified in drawing No GE(N)Comp-03(R)-2019 Sheet 2/2.

Supply, fabrication and fixing Fully retro-reflectorised cautionary, mandatory and informatory sign board of size 45cm regular octagon shape as per IRC: 67-2012 made of high intensity grade sheeting vide clause 801.3 of MORTH specification, frame made out of mild steel angle iron 75mmX75mmX6mm, sign board made by using aluminium sheet 1.5mm thick fixed over angle iron frame, sign board supported on 3m high (2.4m above ground and 0.60m below ground) post made out of 100mm dia Medium Grade MS Pipe confirming to IS 1161-1979 of Grade Fe 410, leg/post embedded in PCC block of size 45cm x 45cm x 60cm in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including necessary excavation and earth work complete all as shown and specified in drawing, aluminium sheet to be covered with high intensity grade retro-reflective sheeting as per IRC standard (AVERY DENNISON) blue/green or as required colour pasted firmly without appearance of bubbles and after that writing/pasted a computer cut letters or sign's of appropriate sizes made from retro reflective tape (High Intensity Prismatic Reflective Sheeting) including two coats of water-based acrylic polyurethane enamel paint on MS surfaces over a coat of red oxide primer. Complete all as per technical specifications and as directed by the Engineer-in-charge. Note:- All other details specified in drawing No GE(N)Comp-03(R)-2019 Sheet 2/2 .

Supply, fabrication and fixing Fully retro-reflectorised cautionary, mandatory and informatory sign board of size 80cm x 60cm rectangular shape as per IRC: 67-2012 made of high intensity grade sheeting vide clause 801.3 of MORTH specification, frame made out of mild steel angle iron 75mmX75mmX6mm, sign board made by using aluminium sheet 1.5mm thick fixed over angle iron frame, sign board supported on 3m high (2.4m above ground and 0.60m below ground) post (two Nos) made out of 100mm dia Medium Grade MS Pipe confirming to IS 1161-1979 of Grade Fe 410, leg/post embedded in PCC block of size 45cm x 45cm x 60cm in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including necessary excavation and earth work complete all as shown and specified in drawing, aluminium sheet to be covered with high intensity grade retro-reflective sheeting as per IRC standard (AVERY DENNISON) blue/green or as required colour pasted firmly without appearance of bubbles and after that writing/pasted a computer cut letters or sign's of appropriate sizes made from retro reflective tape (High Intensity Prismatic Reflective Sheeting) including two coats of water-based acrylic polyurethane enamel paint on MS surfaces over a coat of red oxide primer. Complete all as per technical specifications and as directed by the Engineer-in-charge. Note:- All other details specified in drawing No GE(N)Comp-03(R)-2019 Sheet 2/2.

Supply, fabrication and fixing Fully retro-reflectorised cautionary, mandatory and informatory sign board (Tree Plates) of shape equilateral triangle or circular or Square (appx area of each plates 0.305 Sqm) as directed by Engr-in-Charge as per IRC: 67-2012 made of high intensity grade sheeting vide clause 801.3 of MORTH specification, sign board (tree plates) made by using aluminium sheet 1.5mm thick, aluminium sheet to be covered with high intensity grade retro-reflective sheeting as per IRC standard (AVERY DENNISON) blue/green or as required colour pasted firmly without appearance of bubbles and after that writing/pasted a computer cut letters or sign's of appropriate sizes made out from retro reflective tape (High Intensity Prismatic Reflective Sheeting), plates fixed to the tree/wall by means of fasteners complete all as per technical specifications and as directed by the Engineer-in-charge.

Supply, fabrication and fixing Fully retro-reflectorised cautionary, mandatory and informatory sign board of oval shape (as per sample with Engineer-in-charge) as per IRC: 67-2012 made of high intensity grade sheeting vide clause 801.3 of MORTH specification, oval shape frame made out of mild steel pipe 25mm dia medium grade, sign board supported on post made out of Medium Grade MS hollow Pipes confirming to IS 1161-1979 of Grade Fe 410, leg/post embedded in PCC block of size 50cm x 50cm x 60cm in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including necessary excavation and earth work, sign board made by using MS plate 2mm thick fixed in inner side of MS pipe frame, complete all as shown and specified in drawing, MS plate to be covered with high intensity grade retro-reflective sheeting as per IRC standard (AVERY DENNISON) blue/green or as required colour pasted firmly without appearance of bubbles and after that writing/pasted a computer cut letters or sign's of appropriate sizes made from retro reflective tape (High Intensity Prismatic Reflective Sheeting) including two coats of water-based acrylic polyurethane enamel paint on MS surfaces over a coat of red oxide primer. Complete all as per technical specifications and as directed by the Engineer-in-charge. Note:- All dimensions, size of MS pipes and design as specified in drawing No GE(N)Comp-03(R)-2019 Sheet 1/2.

Supply and fixing Convex safety mirror 1000mm dia made of long life PC material with strong impact resistant fitted with a sun shield or protective hood of colour as approved provided with 75mm dia MS pipe post standard height excluding embedded portion duly painted with two coats of synthetic enamel paint over a coat of red oxide primer to MS surfaces, pipe shall be embedded in PCC (1:2:4) type B-1 using 20mm graded stone aggregate of block of size 45cm x 45cm x 45cm including necessary excavation and earth work, complete all as specified and as directed by Engineer-in-charge. Make : Dark Eye/3M/International Wire Products/ Trafitronics

Supply and fixing solar blinker leds super bright in 200mm signal aspect (Polycarbonate Die molded Body conforming to international standard) the whole assembly includes Solar Panel, Frame for Solar Panel, Traffic Signal Blinker, Wire Harness, Charge Controller, Battery, Battery Box, Signal Pole etc. , high efficiency PWM MOSFET controlled on fixed 4.0m long steel pole duly painted shall be embedded in PCC (1:2:4) type B-1 using 20mm graded stone aggregate of block of size 45cm x 45cm x 45cm including necessary excavation and earth work, complete all as specified and as directed by Engineer-in-charge. Make : Dark Eye/3M/International Wire Products/ Greenlite/Trafitronics

Supply and fixing speed breaker 50mm high, 250mm long, 350mm width made of ABS material, with built-in highly reflective reflectors moulded in PMMA material are welded with ABS plate through ultrasonic welding process, standard skid resistant base, uv, moisture and temperature resistant, modular design in black and yellow combination, including surface to be make level with using PCC as per site requirement and fixing with bolts and adhesive, complete all as specified and as directed by Engineer-in-charge. Make : Cat Part ALC-PSB1 of Asian Loto or equivalent in Dark Eye/3M/International Wire Products/ Trafitronics

Supply and fixing PVC retro reflective tape of size 50mm wide of Colour Red/Yellow/White with min visibility distance 200m complete all as specified and as directed by Engineer-in-charge. Make : Dark Eye/3M/International Wire Products /Trafitronics

Taking down carefully copper/aluminum point wiring (light, fan, socket or power point) complete including fittings such as hylum sheet, switches, ceiling rose, pendent holder, sockets, regulator including rusted/broken concealed conduit, junction and sunken boxes etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for concealed Point wiring complete with 1.5 Sqmm (nominal cross section area) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC rigid conduit 20mm dia (heavy duty) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, Pressed steel powder coated sunken box of suitable size (Min 60mm deep, made from 1.6mm thick sheet), 3mm thick bakelite plastic laminated hylem sheet for mounting of switches and socket, fan regulator, wiring for light /fan/ bell point controlled by one switch (on indipendent board) including frame for covering the switches/socket/regulator, including provn of 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) to matching with existing surfaces complete all as specified and as directed by Engineer-in-charge. (switches, sockets, fan regulator etc. shall be measured and paid separately under appropriate item of BOQ).

All as per above Srl item No. 173 but for one socket out let 5/6 Amps point controlled by one switch (on same board) complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ).

All as per above Srl item No. 173 but for one socket out let 5/6 Amps point controlled by one switch (on indipendent board and not below the any other switch board) complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ).

Material and labour for concealed Point wiring complete with 2.5 Sqmm (nominal cross section area) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC rigid conduit 20mm dia (heavy duty) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, Pressed steel powder coated sunken box of suitable size (Min 60mm deep, made from 1.6mm thick sheet), 3mm thick bakelite plastic laminated hylem sheet for mounting of switches and socket, wiring for one socket out let 15/16 Amps point controlled by one switch (on indipendent board) including frame for covering the switches/socket, including provn of 2.5 Sqmm FRLSH PVC insulated solid copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) to matching with existing surfaces complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ).

Material and labour for Point wiring complete with 1.5 Sqmm (nominal cross section area) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through existing concealed PVC rigid conduit, but new sunken boxes, 3mm thick bakelite plastic laminated sheet for mounting of switches, for one light point controlled by two Nos- two way switchs including frame for covering the switch, and making good disturbed surfaces of walls/ceiling/around sunken box etc. by using CM (1:3) to matching with existing surfaces including taking down carefully existing any type of wiring (complete wiring upto holder and both two way switches) including fittings such as hylum sheet, switches, lamp holder, sunken boxes etc but except concealed conduit complete all as specified and as directed by Engineer-in-charge. (switches shall be measured and paid separately under appropriate item of Sch ‘A’ ).

Supply and fixing switch piano flush type (ISI marked), 5/6Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 3/5 pin 5/6 Amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing switch piano flush type (ISI marked), 15/16Amps, single pole, one way complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 3/5 pin 15/16 Amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing ceiling rose (ISI marked) surface type polycarbonate isolated body two to three terminal, topline series 20x50mm, 6 Amp, 250 volts, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing batten holder (ISI marked) polycarbonate cased body (B22 base), top line series, with back plate, 5/6Amps, 250 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing stepped type (1-4), electronic Fan regulator (two module), 100 watt, 250 volts, fixed on laminated sheet suitable for ceiling fan complete all as specified by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing switch piano flush type (ISI marked), 5/6Amps, single pole, two way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing switch piano flush type (ISI marked), Bell Push, 5/6Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be measured and paid in point wiring item of BOQ).

Supply and fixing electric calling Bell Ding Dong type, AC 230 Volts single pole including making elctric connection and testing, complete all as specified and as directed by Engr-in-charge.

Material and labour for concealed sub main wiring with 6 Sqmm single core (Two run) FRLSH PVC insulated multistrand copper conductor drawn through existing PVC conduit, independent circuit from DB and including one run 6 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor continues as earth wire connected to earth dolly etc. including taking out old sub main wiring of any conductor any size from conduit and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 6 sqmm copper wire shall be measured as one RM length for payment.

Material and labour for concealed sub main wiring with 6 Sqmm single core (Two run) FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit from DB and including one run 6 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor continues as earth wire connected to earth dolly etc. including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, taking out old sub main wiring of any conductor any size from conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 6 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Material and labour for concealed sub main wiring with 6 Sqmm single core (Two run) FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit from DB and including one run 6 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor continues as earth wire connected to earth dolly etc. including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 6 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Material and labour for concealed sub main wiring with 4 Sqmm single core (Two run) FRLSH PVC insulated unsheathed multistrand copper conductor cable drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit and including one run 4 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor cable continues as earth wire connected to earth dolly etc. including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 4 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Supply and fixing (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 08 Way (08 modules) 230/240V, double door, earth bar, copper bus bar and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 12 Way (12 modules) 230/240V, double door, earth bar, copper bus bar and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (verticle, made out of CRCA sheet) VTPN, 6 Way 415V, double door, earth bar, copper bus bar and neutral link, protection class IP-43 suitable for provision to mount 4 pole MCCB/RCBO (incomer ) and SP/DP/TP MCB's (18 modules) outgoing, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCCB/MCB/ISOLATOR shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing MCCB of capacity 100 Amp, TPN, 415 volt, short circuit breaking capacity not less than 16KA , thermal magnetic trip, setting 80-100%, Icu-100% Ics confirming to IEC-947, IS-13947, including thimbles, nuts, bolts, washers etc , MCCB fixing in new DB or the existing DB/Panel including making incoming, outgoing connections complete all as specified and as directed by Engineer-in-charge . Note :- DB shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing MCCB of capacity 100 Amp, FP, 415 volt, short circuit breaking capacity not less than 25KA , thermal magnetic trip, setting 80-100%, Icu-100% Ics confirming to IEC-947, IS-13947, including thimbles, nuts, bolts, washers etc , MCCB fixing in new DB or the existing DB/Panel including making incoming, outgoing connections complete all as specified and as directed by Engineer-in-charge . Note :- DB shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing MCB ‘C’ curve suitable for 230 volts AC supply, 40 to 63 Amps, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing MCB ‘C’ curve suitable for 240 volts AC supply, 63 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing MCB ‘C’ curve suitable for 240 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing (concealed in wall or as directed) single pole and neutral sheet metal enclosure (AC Box) with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply including taking down old unserviceable enclosure complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (concealed in wall or as directed) single pole and neutral sheet metal enclosure (AC Box) with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 04 Way (04 modules) 230/240V, double door, earth bar, copper bus bar and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ.

Taking down old unserviceable tube light fitting, mirror light fitting and Wall Mount Bracket Light fixture any type and capacity complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable false ceiling light fitting any type and capacity complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable street light fitting with brackets any type and capacity complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing wall mounted LED Batten T-8 Retro LED 18/20 watt (100 lumens per watt), appx 4 feet long, pre wired including LED tube light with in built driver, not less than 6000K, complete fitting and all other accessories fitting arrangements including electric connection complete all as specified and as directed by Engineer-in-Charge. Make - Cat part No BLRB 18W CWc and BLRB-DB 118 of Bajaj / LT8-20-865-2 and DMLN1LT8-16 of Crompton / PHOTONULTRA 1213T8SSTL18WLED865SPC and REGALBATTENT 8UPTO1X22WSSBSWH of Havells

Supply and fixing LED light fiting 9/10 watt (100 lumens per watt), appx 1 feet long with in built driver, complete fitting ready to use in all respect with tube rod and all other accessories fitting arrangements including electric connection complete all as specified and as directed by Engineer-in-Charge. Make - Cat part No LCL-07-CDL of Crompton / LHEXARP 7PN 1W009 of Havells

Supply and fixing Surface mounted decorative circular/round shaped wall/ceiling mounted LED luminaire 12 Watt, 6000K, complete fitting with LED lamps high brightness, driver, all other accessories fitting arrangements including electric connection complete all as specified and as directed by Engineer-in-Charge. Make - Cat part No BGSLO sleek surface 12 W WH RD of Bajaj / LCDSPL-R-12-CDL or LCSR-12-CDL of Crompton / LHEAA RP 7UL 1W012 of Havells / SLE DLS 12W XX stellar RD of Surya

Supply and fixing recessed LED ceiling tile slim panel with wide light window for maximized glare free output suitable for 300x1200mm and ceiling cutout 295x1195mm modular grid/POP ceiling complete fitting with separate electronic driver and high brightness LEDs 36 W (100 lumens per watt), not less than 5700K including connecting electric connection, complete all as specified and directed by Engineer-in-Charge. Make : Cat part No. LCPL-36-CDL (1x4) of Crompton / BZRSLL 36W GZ1 CW of Bajaj / PLUTONEO4X1PLR36WLED840S of Havells

Supply and fixing Sleek Pressure die cast aluminium housing/body, heat resistant clear glass, LED lens for wide beam, energy saving, IP65/66 protection, not less than 5700K, better optics for uniform distribution street/Roadway luminaire with high power LED 25 watt complete fitting with driver, LED strip and all other accessories etc, suitable for 40/32mm OD entry for direct mounting on pipe bracket, fixing on poles/along wall with and including brackets made out of GI tubing light grade 40mm dia, 2 metre long bent to shape at 120 degree angle at half metre from bottom (as per sample), fixing with MS clamp (02 Nos) and nut bolts, including before fixing applying two coats of aluminium paint on bracket and clamp over a coat of red oxide primer, including making electric connection with using twin core copper cable of suitable size complete all as specified and as directed by Engineer-in-charge. Make - Cat part No LSTS-25-CDL of Crompton/ BRLEP 25W LED WH of Bajaj / ENDURA PEARL SL25W LED757SASYTOPC of Havells

Supply and laying XLPE LT Cable of size 50 Sqmm, 4 core, 1100 Volt grade heavy duty with XLPE insulated, stranded aluminium conductor served with an inner sheathening of PVC tape armoured with Galvanized steel strip or wire and over all PVC Sheathed stranded conductor conforming to IS- 7098 (Part-I) with latest amendments laid in trenches/fixed to wall/pole/laid in floor including necessary connections and suitable size of thimbling complete all as specified and as directed by Engineer-in-charge. Note :- (i) Excavation, earth work, sand cushioning, brick protection, cutting of road and pipe shall be measured & paid separately under appropriate item of this Schedule.)

Supply and laying XLPE LT Cable of size 10 Sqmm, 2 core, 1100 Volt grade heavy duty with XLPE insulated, stranded aluminium conductor served with an inner sheathening of PVC tape armoured with Galvanized steel strip or wire and over all PVC Sheathed stranded conductor conforming to IS- 7098 (Part-I) with latest amendments laid in trenches/fixed to wall/pole/laid in floor including necessary connections and suitable size of thimbling complete all as specified and as directed by Engineer-in-charge. Note :- (i) Excavation, earth work, sand cushioning, brick protection, cutting of road and pipe shall be measured & paid separately under appropriate item of this Schedule.)

Supply and filling Local sand cushioning , with dry and clean sand, over and under the under ground cables in trenches, ducts for cable protection including consolidation, 80mm thick to the authorized width as per SSR–Part-I before laying of cable and 150mm thick after laying of cable complete all as specified and as directed by Engineer-in-Charge. (Note :- For measurement purpose puned thickness shall be measured and paid i.e 18cm.)

Supply and laying Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing/laying GI tubing, light grade, 40 mm bore for protection of cable under hardstanding/fixed along poles/wall, laid in in trenches etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing exhaust fan 300 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, 04 No bolts grouting in wall in PCC (1:2:4) using 12.5mm graded stone aggregate for hanging the fan and making good the disturbed surface as per existing surfaces, fixing the fan by bolts and washers and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Make - Usha / Bajaj / Khaitan / Orient / Crompton / Polar

Disconnecting electric connection and taking down carefully serviceable ceiling fans or Exhaust Fans and keep in safe custudy. After completing the building repair work refixing /hanging the ceiling fan as directed including electric connection with and including new flexible copper wire from ceiling rose/connector to fan connector complete all as specified and as directed by Engineer-in-charge.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including earth continuity GI wire 4 mm (upto test point from earth plate i.e. 7.5m min) by means of GI bolts/nuts/washers and including protected by 15mm dia GI light grade protection pipe from earth plate to test point, including making of test point made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos- 8mm dia 25mm long hex head screw. Earth plate shall be surrounded by packed layer of char coal/coke & salt all around bottom and top with alternative layer. 20mm GI light grade pipe for watering (should be 10cm above GL) and including socket, plug, funnel, wire mesh, CI cover 10mm thick hanged to CFI frame, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate), including necessary form work, excavation and earth work in any type of soil , returning filling and disposal of surplus soil to a distance not exceeding 50m, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and and as directed by Engineer-in-charge, Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

BALAJI CONSTRUCTIONS

V K CONTRACTOR

M/s Balvinder Singh Engineer and Contractors

SHARDA ENTERPRIES