CWE/FZR-60/2023-24 SPECIAL REPAIR OF BLDG NO P-12 (OR MD ACCN AT NEEL BHAWAN) UNDER GE (WEST) FEROZEPUR CANTT

Amount

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15 cm thickness below or above ground level complete all as specified & as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified & as directed by Engineer-in-Charge.

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour over a screed layer of 15 mm thick in CM 1:6 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m as in skerting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and backing with 10 mm thick in CM 1:4 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 450X 350X 7mm thick glazed coloured (digital coloured) ceramic tiles on vertical surface of such as skirting, dados and risers to steps etc., including 10mm thick rendering in CM 1:4 on brick or concrete surface finished rough to received dado/ skirting, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade with cement mortar bedding and removing off the premises complete all as specified & as directed by Engineer-in-Charge.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick over 15 mm thick cement screed (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Kota stone slab 20-25 mm thick in skirting, etc over 15 mm thick cement screed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish, complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 18 to 20 mm thick Baroda green marble in single piece incl nosing at front and sides in steps, jambs,pillars,window cills,cooking platforms,staircase and like with bull nosing in cm(1:4) incl pointing in white cement(1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard or steps,edge moulding,making 30 mm dia hole in cooking counter slab and green marble top for gas pipe including 15mm thick screed bed in cm 1:4 and providing edge moulding to marble incl machine polishing to edge to finish etc complete all as specified & as directed by Engineer-in-Charge.

Taking down chowkhat with shutter exe 1.50 Sqm and n exe 4 Sqm( without taking off shutter) each complete all as specified & as directed by Engineer-in-Charge.

Taking down chowkat with shutter n.exe 1.50 sqm (without taking off shutters) each complete all as specified & as directed by Engineer-in-Charge.

Taking down shutters of any description,exc.1.0 sqm and not exc.2 sq. m each and after repair refixing in same opening complete all as specified & as directed by Engineer-in-Charge.

Resecuring, or easing & adjusting without taking down shutter of any description exc 1 sqm n exc 2 sqm each complete all as specified & as directed by Engineer-in-Charge.

Taking down shutters only of any description exc 1 sqm and not exc 2 sqm each complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010) complete all as specified & as directed by Engineer-in-Charge.

Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etccomplete all as specified & as directed by Engineer-in-Charge.

All as per item no 15 above here-in-before but size 125x60mm with double rebate.

Material and labour Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats,bed blocks, coping etc including necessary form work complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 35mm thick second class hard wood plain framed panelled shutters (any number of panels ), with panels of timber flat on both sides (feather edge), or of veneered particle board medium density wood wood particle board with commericial face veneers and fitted to chowkats complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete with oil putty complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staple etc complete all as specified & as directed by Engineer-in-Charge.

Pressed steel frames made of 1.25mm thick MS sheet of profile 75 x50mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified & as directed by Engineer-in-Charge.

Dismantling of boarding, any description, fixed in any position with nails complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 18mm thick Prelaminated particle board,flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade, prelaminated both side with decorative choice lamination, fixed with screws as in shutters & shelvesincluding 6mm thick teak wood leaping on three sides and 20mm thick on hanging side complete all as specified & as directed by Engineer-in-Charge.

Providing and fixing factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc. complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 30mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing alluminium anodised handles 100 mm long fixed to windows complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT handle 125mm long fixed with steel screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 200mm long aluminium, anodised barrel tower bolts of extruded section, complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 150mm Extruded aluminium alloy handle complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 100mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zink primer on steel surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs brass chromium plated bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs brass chromium plated long body bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs chromium plated cast copper alloy 1-way angle cock with flange suitable for 15mm bore pipe, complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing wall mixer with 'L' bend (Provision for OH shower) 15mm for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair Brass CP wash hand basin mixer incl copper nipple for connecting with PVC connection 15mm for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 15mm dia CP Sink cock swan neck regualar spout with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Cabinet Mirror (400mm x 500mm) complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified & as directed by Engineer-in-Charge.

Material and labour Corner glass shelves 300 mm radious,8mm thick as per sample radious for bath room, fixed on suitable support of brass chromium plated clips complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs,in repair complete all as specified & as directed by Engineer-in-Charge.

Toilet paper holder of brass, chromium plated or stainless steel fixed in repair to walls with chromium plated (CP) brass screws , complete all as specified & as directed by Engineer-in-Charge.

Supply & fixed replacement of pressure JET for EWC including PVC connection and CP fitting as fixed in repairs complete all as specified & as directed by Engineer-in-Charge.

Vitreous china wash down water closet pan ( pedestal pattern ), white/ coloured including seat & cover, flush pipe, connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs, Vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC water tank all as specified in SSR Part-I complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Stainless steel plate rack of standard pattern & of size 900 x 750 x 250 mm.The thickness of stainless steel sheet shall be 1.00 mm & grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 15 mm dia including taking up or down old steel tubing complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 20 mm dia including taking up or down old steel tubing complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Type A1 1:1½:3 (20 mm graded aggregate) landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & as directed by Engineer-in-Charge.

Use and waste of formwork to chullah hoods, chajjas, troughs and similar work, rough finish surface of concrete flat complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing deformed or twisted TMT bar 10 mm dia and over cut to length, bent to shape required, incl cranking bending and binding with MS wire (annealed) not less than 0.9mm or securing with clips complete all as specified & as directed by Engineer-in-Charge.

Dismantling brick work built in cement mortar of any specification and in any position complete all as specified & as directed by Engineer-in-Charge.

Material and labour Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified & as directed by Engineer-in-Charge.

All as per item above but using old bricks retrieved from item no 70 demolition including cleaning and removal of mortar from old bricks complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified & as directed by Engineer-in-Charge.

Taking down cement plaster any description on brick or stone walls, /RCC walls surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified & as directed by Engineer-in-Charge.

Material and labour 10 mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth with out using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or conrete surfaces, surfaces finished even and fair complete all as specified & as directed by Engineer-in-Charge.

Material and labour Rendering 5mm thick in cement mortar (1:3) on in ceiling, soffits of chajja or similar location any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement,etc complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer and applying a coat of 1mm thick wall care putty complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkaliresistant priming paint complete all as specified & as directed by Engineer-in-Charge.

Material and labour for white washing three coats on ceiling incl preparation of newly plastered surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour for white washing one coats on ceiling incl preparation of old plastered surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour for complete removal of old existing treatment on walls, cornices etc by brooming down or steel wire brushing scrapping down smoke soot moulds, moss and efflorescence salt and trading oil decorated surface of walls and applying a coat of wall care putty of approved make as on wall surface and two coats of oil based distemper (white or tinted) complete all as specified & as directed by Engineer-in-Charge.

Material and labour for complete removal of old existing surface and applying two coats cement based paint over one coat of alkali resistant priming paint complete all as specified & as directed by Engineer-in-Charge.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified & as directed by Engineer-in-Charge.

Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified & as directed by Engineer-in-Charge.

Surface excavation nexc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified & as directed by Engineer-in-Charge.

Hardcore of Broken broken bricks gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 50 mm thik Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub floors, sub bases,floors and paving etc. complete all as specified & as directed by Engineer-in-Charge.

Material and labour for precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and pigment laid dry over a layer of 25 mm thick sand cushioning complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified & as directed by Engineer-in-Charge.

Material and labour PCC 1:2:4 type B-1 using 20m graded stone aggregates as in kerbs, rounded or chamfered on edges complete all as specified & as directed by Engineer-in-Charge.

Material and labour Cement concrete (1:4:8) type D2 40mm graded agg in foundations/sunken filling and mass concrete complete all as specified & as directed by Engineer-in-Charge.

Material and labour for rendering 10mm thick in cm (1:3) on concrete surfaces of roof padding with integral water proofing compound @ 3 % by weight of cement content finished even & smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.. Note :- Water proofing compound to be measured & paid separately.

Supply only integral Liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge. (WPC to be mixed @200ml per 50 Kg bag of cement)

Cutting grooves in brick wall, 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polster non wove fabric (wt. not less than 150 gms/sqm) laid over primed / tack coat of paving bitumen 85/25 on roof surfaced by forced applicaion complete including taking down/removal of existing treatment complete all as specified & as directed by Engineer-in-Charge.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified & as directed by Engineer-in-Charge.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) and removing from site complete all as specified & as directed by Engineer-in-Charge.

Material and labour 20 mm thick screed bed or bedding layer of mortar in CM(1:3) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane complete all as specified & as directed by Engineer-in-Charge.. Note: WPC shall be measured and paid separately

Supply only water proofing compound.

Cement concrete type B-1, 1:2:4 (20mm graded aggregate), 50mm avg thickness as in roof padding complete all as specified & as directed by Engineer-in-Charge.

Material and labour Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified & as directed by Engineer-in-Charge.

Material and labour For APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) Laid on primed surface by forced application including bitumen primer complete all as specified & as directed by Engineer-in-Charge.

Material and labour for applying evenly a coat of industrial bitumen 85/25 primer @ 1.2 Kilogram per square metre including preparation of roof surfaces complete all as specified & as directed by Engineer-in-Charge.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed by Engineer in Charge

Material and labour Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and as directed by Engineer in Charge for One light/fan/Bell Point controlled by one single pole one way switch.

ditto all as per item No 105 above but for one socket outlet on the same board controlled by one single pole one way switch

ditto all as per item No 105 above but for one 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

ditto all as per item No 105 above but for one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete all as specified and as directed by Engineer in Charge

Supply and fixing Switch piano flush type single pole one way 5/6 Amp complete all as specified and as directed by Engineer in Charge

Supply and fixing Switch piano flush type 15 amps, single pole one way duly ISI marked complete all as specified and as directed by Engineer in Charge

Supply and fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked complete all as specified and as directed by Engineer in Charge

Supply and fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked complete all as specified and as directed by Engineer in Charge

Supply and fixing bell push flush type 5 Amps duly ISI marked complete all as specified and as directed by Engineer in Charge

Supply and fixing ceiling rose, PVC/Polycarbonate,isolated three terminals complete all as specified and as directed by Engineer in Charge

Supply and fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified and as directed by Engineer in Charge

Supply and fixing bell ding dong type AC 230 volt single pole complete all as specified and as directed by Engineer in Charge

Supply and fixing stepped type electronic fan regulater flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and as directed by Engineer in Charge

Supply and fixing exhaust fan,steel body AC single phase 230 V of size 300mm sweep with blades and frame and louvers complete all as specified and as directed by Engineer in Charge

Supply and fixing exhaust fan made of strudy engineering plastic complete with louvers shutter,voltage 230 V,50 Hz,RPM 1200 copper winding of sweep 300mm complete all as specified and as directed by Engineer in Charge

Supply and fixing LED tube light fitting 1 X 20W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engineer in Charge

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engineer in Charge

Supply and fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and as directed by Engineer in Charge

Supply and fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and as directed by Engineer in Charge

Supply and fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified and as directed by Engineer in Charge

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by Engineer in Charge

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by Engineer in Charge

Supply and fixing SPN 32 Amp rating 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by Engineer in Charge

Supply and fixing sheet metal enclousers with socket plug top and MCBs 20 Amp complete all as specified and as directed by Engineer in Charge

Material and labour for sub main wiring of 4 sqmm PVC inulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC unsheathered FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia complete all as specified and as directed by Engineer in Charge (Note : two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall be measured as one length)

Material and labour for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and as directed by Engineer in Charge ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core complete all as specified and as directed by Engineer in Charge

Excavation in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr depth and getting out in soft/loose soil complete all as specified and as directed by Engineer in Charge

Returning, filling, including spreading , levelling, watering and well ramming in layers not exc 25 cm in soft/loose complete all as specified and as directed by Engineer in Charge

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer in Charge

Material and labour for sand cushioning with a layer of fine sand 8 cm thick begore laying of cable and 5 cm thick after laying of cable in trenches complete all as specified and as directed by Engineer-in-Charge. Notes : (i) Excavation and earth work to be measured and paid separately). (ii) Thickness of 18 cms after punning shall be considered for payment.

Material and labour bricks common burnt clay building bricks sub class 'B' designation 75 laid dry width wise across the line of the cable in trenches for protection of UG cable complete all as specified and as directed by Engineer in Charge

Material and labour for mild steel galvansied iron pipe light grade(ISI grade) 40 mm bore for passing of earth lead laid in trenches fixed to walls, laid in floors, roads including all fittings i.e. MS clamps nuts & bolts etc as required complete all as specified and as directed by Engineer in Charge

M/s Vishant Construction Co

M/S N Maini Constrution

Kissan contractor and engg works

Dee Kay EnterPrises

M/s S B Construction Company

M/s Sarup Singh

M/s Harkesh Kumar Bansal