Loading
Loading…
Loading…
Tender Value
₹10.5 Cr
EMD Value
₹21.1 L
Closing Date
14 Sept 2026, 3:00 pm
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
NORTH
16 conditions · 5 needing a document upload
The Minimum Eligibility Criteria for open tenders costing Rs.50 Lakhs & above is given below:-Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
1.1.1: For Standard Technical Criteria the Similar Nature of Work: (1) For Civil Work: "Any Civil Engineering work involving construction of RCC Framed building(s). The cost component of RCC building(s) shall be at least 30% of tendered value." (2) For Electrical Work: "Electrification/Rewiring of Service or Residential Buildings/Yard/ HT/LT Sub-Station work/HT/LT Cable work/ Street Lighting/ Platform or Building Lighting management/Circulating Area lighting/Electrical Overhead Power Supply Work/Electrical pump work etc."
Special Condition: As per Dy. Chief Engineer (Works), Mumbai CSMT's letter No. W.187.R.GCC dated 24.05.2019, if any contract is terminated under Clause 62 of GCC due to contractor's default, such contractor shall be temporarily debarred from participation in any tender in that Division for a period of one year from the date of termination. Accordingly, the contractor/tenderer shall submit a declaration stating that no contract of the firm has been terminated under Clause 62 of GCC due to contractor's default in this Division. ( Click here to download Format)
18 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Documents to be Submitted Along with Tender: (i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be.
Following documents shall be submitted by the tenderer
(a)Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) of General Conditions of Contract-2022 and Para 1.0 of Minimum Eligibility Criteria of Instructions/Special Conditions to the tenderers of tender document and as amended/corrected upto latest correction slip.
(b)HUF: (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of General Conditions of Contract-2022 and Para 1.0 of Minimum Eligibility Criteria of Instructions/Special Conditions to the tenderers of tender document and as amended/corrected upto latest correction slip.
(c)Partnership Firm: (i) All documents as mentioned in Para18 of the Tender Form (Second Sheet) of General Conditions of Contract-2022 andPara17 of the Tender Form (Second Sheet) of Instructions to the tenderers and conditions of tender of tender document and as amended/corrected upto latest correction slip
(d)Joint Venture (JV): All documents as mentioned in Para 17 of the Tender Form (Second Sheet)of General Conditions of Contract-2022 and Para16 of the Tender Form (Second Sheet) of Instructions to the tenderers and conditions of tender of tender document and as amended/corrected upto latest correction slip.
(e)Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii)A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv)All other documents in terms Para 10 of the Tender Form (Second Sheet) of General Conditions of Contract-2022 and Para 1.0 of Minimum Eligibility Criteria of Instructions/Special Conditions to the tenderers of tender document and as amended/corrected upto latest correction slip.
(f)LLP (Limited Liability Partnership): (i)A copy of LLP Agreement (ii)A copy of Certificate of Incorporation (iii)A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (v)An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v)All other documents in terms of Para 10 of the Tender Form (Second Sheet) of General Conditions of Contract-2022 and Para 1.0 of Minimum Eligibility Criteria of Instructions/Special Conditions to the tenderers of tender document and as amended/corrected upto latest correction slip.
(g)Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) Acopy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of General Conditions of Contract- 2022 and Para 1.0 of Minimum Eligibility Criteria of Instructions/Special Conditions to the tenderers of tender document and as amended/corrected upto latest correction slip. (iii)If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender. (iv)After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society / HUF/LLP etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted. (v) A tender from JV shall be considered only where permissible as per the tender conditions. (vi) The Railway will not be bound by any change of power of attorney or in the composition of the firm made subsequent to the submission of tender. Railway may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
Sole proprietor/a company or a partnership firm/joint venture (JV)/registered society/registered trust / HUF/LLP, Power of Attorney etc: The tenderer whether sole proprietor/ a company or a partnership firm/ registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and f\lather to dealwith the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shallbe summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with allother contractualactivities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate
Itarsi-Nagpur Development of Infrastructure for track machine siding 03 Nos (Junnardeo, Morshi and Bordhai)
DRMWNGP-89-2026-01~CR
DRMWNGP-89-2026-01
Open
Works - General
12 Months
Nagpur, Maharashtra
₹0
₹21.1 L
21 Aug 2026
21 Aug 2026
31 Aug 2026
345 items across 9 schedules · ₹8,31,34,760.2 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | EARTH WORK:- Earth work in excavation by mechanical means(Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.(a) All kinds of soil. (DSR- 2023 ITEM CODE - 2.8.1) | cum | 1256.00 | 260.3 | 3,26,936.8 |
| 2 | EARTH WORK:- Excavation work by mechanical means(Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.(a) Ordinary rock. (DSR-2023 ITEM CODE - 2.9.1) | cum | 1256.00 | 632.95 | 7,94,985.2 |
| 3 | EARTH WORK:- Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed,within a lead of 50 m :(a) All kinds of soil(i) Pipes, cables etc, not exceeding 80 mm dia. (DSR- 2023 ITEM CODE - 2.10.1.1) | Metre | 225.00 | 215.6 | 48,510 |
| 4 | CONCRETE WORK:- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up toplinth level :(a) 1:3:6 (1 Cement : 3 coarse sand(zone-III)derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources). (DSR-2023 ITEM CODE - 4.1.5) | cum | 38.00 | 7,294.7 | 2,77,198.6 |
| 5 | CONCRETE WORK:- Providing and laying damp-proof course 50mmthick with cement concrete 1:2:4 (1 cement : 2coarse sand (Zone III) derived from naturalsources : 4 graded stone aggregate 20mmnominal size derived from natural sources). (DSR-2023 ITEM CODE - 4.11) | Sqm | 52.00 | 495.75 | 25,779 |
| 6 | REINFORCED CEMENT CONCRETE:- Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :(a) 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (DSR-2023 ITEM CODE - 5.1.2) | cum | 176.00 | 9,045.75 | 15,92,052 |
| 7 | REINFORCED CEMENT CONCRETE:- Reinforced cement concrete work in beams,suspended floors, roofs having slope up to 15°landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (DSR-2023 ITEM CODE - 5.3) | cum | 137.00 | 11,505.5 | 15,76,253.5 |
| 8 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for :(a) Foundations, footings, bases of columns, etc.for mass concrete. (DSR-2023 ITEM CODE - 5.9.1) | Sqm | 240.00 | 392.15 | 94,116 |
| 9 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for : (b) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. (DSR-2023 ITEM CODE -5.9.2) | Sqm | 702.00 | 842.5 | 5,91,435 |
| 10 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for : (c) Suspended floors, roofs, landings, balconies and access platform. (DSR-2023 ITEM CODE - 5.9.3) | Sqm | 13.00 | 927.25 | 12,054.25 |
| 11 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for : (d) Lintels, beams, plinth beams, girders,bressumers and cantilevers. (DSR-2023 ITEM CODE - 5.9.5) | Sqm | 503.00 | 736.4 | 3,70,409.2 |
| 12 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for : (e) Columns, Pillars, Piers, Abutments, Posts and Struts. (DSR-2023 ITEM CODE - 5.9.6) | Sqm | 478.00 | 961.3 | 4,59,501.4 |
| 13 | REINFORCED CEMENT CONCRETE:- Centering and shuttering including strutting,propping etc. and removal of form for : (f) Edges of slabs and breaks in floors and walls. (i) under 20 cm wide (DSR-2023 ITEM CODE - 5.9.16.1) | Metre | 90.00 | 208.55 | 18,769.5 |
| 14 | REINFORCED CEMENT CONCRETE:- Providing and laying in position ready mixed orsite batched design mix cement concrete forreinforced cement concrete work; using coarseaggregate and fine aggregate derived fromnatural sources, Portland Pozzolana / OrdinaryPortland /Portland Slag cement, admixtures inrecommended proportions as per IS: 9103 toaccelerate / retard setting of concrete, toimprove durability and workability withoutimpairing strength; including pumping ofconcrete to site of laying, curing, carriage for allleads; but excluding the cost of centering,shuttering, finishing and reinforcement as perdirection of the engineer- in-charge; for thefollowing grades of concrete.Note: Extra cement up to 10% of the minimumspecified cement content in design mix shall bepayable separately. In case the cement contentin design mix is more than 110% of thespecified minimum cement content, thecontractor shall have discretion to either redesignthe mix or bear the cost of extra cement(a) All works upto plinth level(i) Concrete of M25 grade with minimm cementcontent of 330 kg /cum. (DSR-2023 ITEM CODE - 5.33.1.1) | cum | 52.00 | 9,504.75 | 4,94,247 |
| 15 | REINFORCED CEMENT CONCRETE:- Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and work ability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering,shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either redesign the mix or bear the cost of extra cement. (b) All works above plinth level upto floor V level(i) Concrete of M25 grade with minimm cementcontent of 330 kg /cum. (DSR-2023 ITEM CODE - 5.33.2.1) | cum | 29.00 | 9,860.4 | 2,85,951.6 |
| 16 | MASONRY WORK :- Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in superstructure above plinth level up to floor V level in :(a) Cement mortar 1:4 (1 cement : 4 coarse sand). (DSR- 2023 ITEM CODE - 6. 34. 1) | cum | 211.00 | 8,962.35 | 18,91,055.85 |
| 17 | MASONRY WORK:- Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS:12894, in super structure above plinth and upto floor V level.(a) Cement mortar 1 : 4 (1 cement : 4 coarse sand). (DSR-2023 ITEM CODE - 6.45.2) | Sqm | 1.00 | 1,105.8 | 1,105.8 |
| 18 | CLADDING WORK:- Providing and fixing 18 mm thick gang saw cut,mirror polished, premoulded and prepolished,machine cut for kitchen platforms, vanitycounters, window sills, facias and similarlocations of required size,approved shade,colour and texture laid over 20 mm thick basecement mortar 1:4 (1 cement : 4 coarse sand),joints treated with white cement, mixed withmatching pigment, epoxy touch ups, includingrubbing, curing, moulding and polishing toedges to give high gloss finish etc. complete atall levels.(a) Granite stone slab colour black, Cherry/Rubyred(i) Area of slab over 0.50 sqm. (DSR-2023 ITEM CODE - 8.2.2.2) | Sqm | 116.00 | 5,136.3 | 5,95,810.8 |
| 19 | CLADDING WORK:- Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (a) Granite work. (DSR-2023 ITEM CODE - 8.3.2) | Metre | 225.00 | 510.95 | 1,14,963.75 |
| 20 | WOOD AND P.V.C WORK:- Providing wood work in frames of doors,windows, clerestory windows and otherframes, wrought framed and fixed in positionwith hold fast lugs or with dash fasteners ofrequired dia & length ( hold fast lugs or dashfastener shall be paid for separately).(a) Second class teak wood. (DSR- 2023 ITEM CODE - 9.1.1) | cum | 1.00 | 1,42,949.7 | 1,42,949.7 |
| 21 | WOOD AND P.V.C WORK:- Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge.(Note:- Butt hinges and necessary screws shall be paid separately)(a) Second class teak wood(i) 30 mm thick shutters. (DSR-2023 ITEM CODE - 9.5.1.2) | Sqm | 4.00 | 3,747.3 | 14,989.2 |
| 22 | WOOD AND P.V.C WORK:- Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates tobe measured). Panelling for panelled orpanelled and glazed shutters 25 mm to 40 mm thick :(a) Float glass panes (i) 4 mm thick glass pane (weight not less than 10kg/sqm). (DSR-2023 ITEM CODE - 9.7.7.1) | Sqm | 5.00 | 2,241.8 | 11,209 |
| 23 | WOOD AND P.V.C WORK:- Providing and fixing ISI marked flush doorshutters conforming to IS : 2202 (Part I) non decorativetype, core of block boardconstruction with frame of 1st class hard woodand well matched commercial 3 ply veneeringwith vertical grains or cross bands and faceveneers on both faces of shutters:(a) 35 mm thick including ISI marked StainlessSteel butt hinges with necessary screws. (DSR-2023 ITEM CODE - 9.21.1) | Sqm | 35.00 | 2,392.65 | 83,742.75 |
| 24 | WOOD AND P.V.C WORK:- Providing and fixing nickel plated M.S. pipecurtain rods with nickel plated brackets :(a) 20 mm dia (heavy type). (DSR-2023 ITEM CODE - 9.47.1) | Metre | 23.00 | 175 | 4,025 |
| 25 | WOOD AND P.V.C WORK:- Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S.flats, square or round bars etc. including priming coat with approved steel primer all complete.(a) Fixed to steel windows by welding. (DSR-2023 ITEM CODE - 9.48.1) | Kg | 375.00 | 219.1 | 82,162.5 |
| 26 | WOOD AND P.V.C WORK:- Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S.flats, square or round bars etc. including priming coat with approved steel primer all complete (b) Fixed to openings /wooden frames with rawlplugs screws etc. (DSR-2023 ITEM CODE - 9.48.2) | Kg | 8.00 | 238.35 | 1,906.8 |
| 27 | WOOD AND P.V.C WORK:- Providing and fixing aluminium sliding doorbolts ISI marked anodised (anodic coating notless than grade AC 10 as per IS : 1868)transparent or dyed to required colour orshade with nuts and screws etc. complete :(a) 300x16 mm. (DSR-2023 ITEM CODE - 9.96.1) | Numbers | 48.00 | 303.25 | 14,556 |
| 28 | WOOD AND P.V.C WORK:- Providing and fixing aluminium tower bolts ISImarked anodised (anodic coating not less thangrade AC 10 as per IS : 1868 ) transparent ordyed to required colour or shade withnecessary screws etc. complete :(a) 100x10 mm. (DSR-2023 ITEM CODE - 9.97.5) | Each | 24.00 | 64.7 | 1,552.8 |
| 29 | WOOD AND P.V.C WORK:- Providing and fixing aluminium handles ISImarked, anodised (anodic coating not less thangrade AC 10 as per IS : 1868) transparent ordyed to required colour or shade withnecessary screws etc. complete : (a) 125 mm. (DSR-2023 ITEM CODE - 9.100.1) | Each | 48.00 | 66.25 | 3,180 |
| 30 | WOOD AND P.V.C WORK:- Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete. (a) Single rubber stopper. (DSR-2023 ITEM CODE - 9.101.1) | Each | 18.00 | 39.6 | 712.8 |
| 31 | WOOD AND P.V.C WORK:- Providing and fixing factory made P.V.C. doorframe of size 50x47 mm with a wall thickness of5 mm, made out of extruded 5 mm rigid PVCfoam sheet, mitred at corners and joined with 2Nos of 150 mm long brackets of 15x15 mm M.S.square tube, the vertical door frame profiles tobe reinforced with 19x19 mm M.S. square tubeof 19 gauge, EPDM rubber gasket weather sealto be provided through out the frame. Thedoor frame to be fixed to the wall using M.S.screws of 65/100 mm size, complete as permanufacturer's specification and direction ofEngineer-in-Charge. (DSR-2023 ITEM CODE - 9.119) | Metre | 68.00 | 492.7 | 33,503.6 |
| 32 | WOOD AND P.V.C WORK:- Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top &bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to formtop and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail.Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 )thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles& rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the'C' Channel using PVC solvent adhesive etc.complete as per direction of Engineer-in charge,manufacturer's specification & drawing.(a) 30 mm thick pre laminated PVC door shutters. (DSR-2023 ITEM CODE - 9.120.2) | Sqm | 19.00 | 3,663.8 | 69,612.2 |
| 33 | WOOD AND P.V.C WORK:- Providing and fixing fly proof stainless steelgrade 304 wire gauge, to windows andclerestory windows using wire gauge withaverage width of aperture 1.4mm in bothdirections with wire of dia. 0.50 mm allcomplete.(a) With 12 mm mild steel U beading. (DSR-2023 ITEM CODE - 9.135.2) | Sqm | 60.00 | 1,228 | 73,680 |
| 34 | ALUMINIUM WORK:- Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) :(a) For fixed portion(i) Powder coated aluminium (minimum thickness of powder coating 50 micron). (DSR- 2023 ITEM CODE - 21.1.1.2) | Kg | 360.00 | 530.9 | 1,91,124 |
| 35 | ALUMINIUM WORK:- Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : (b) For shutters of doors, windows & ventilatorsincluding providing and fixing hinges/ pivotsand making provision for fixing of fittingswherever required including the cost of EPDMrubber / neoprene gasket required (Fittingsshall be paid for separately). (i) Powder coated aluminium (minimum thicknessof powder coating 50 micron). (DSR- 2023 ITEM CODE - 21.1.2.2) | Kg | 270.00 | 634.45 | 1,71,301.5 |
| 36 | ALUMINIUM WORK:- Providing and fixing glazing in aluminium door,window, ventilator shutters and partitions etc.with EPDM rubber / neoprene gasket etc.complete as per the architectural drawings andthe directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basicitem):(a) With float glass panes of 4.0 mm thickness(weight not less than 10 kg/sqm). (DSR-2023 ITEM CODE - 21.3.1) | Sqm | 36.00 | 1,176.8 | 42,364.8 |
| 37 | STEEL WORK:- Structural steel work riveted, bolted or weldedin built up sections, trusses and framed work,including cutting, hoisting, fixing in position andapplying a priming coat of approved steelprimer all complete. (DSR- 2023 ITEM CODE - 10.2) | Kg | 675.00 | 133.7 | 90,247.5 |
| 38 | STEEL WORK:- Supplying and fixing rolling shutters ofapproved make, made of required size M.S.laths, interlocked together through their entirelength and jointed together at the end by endlocks, mounted on specially designed pipe shaftwith brackets, side guides and arrangementsfor inside and outside locking with push andpull operation complete, including the cost ofproviding and fixing necessary 27.5 cm longwire springs manufactured from high tensilesteel wire of adequate strength conforming toIS: 4454 - part 1 and M.S. top cover of requiredthickness for rolling shutters.(a) 80x1.25 mm M.S. laths with 1.25 mm thick topcover. (DSR-2023 ITEM CODE - 10.6.1) | Sqm | 8.00 | 3,653.2 | 29,225.6 |
| 39 | STEEL WORK:- Providing and fixing ball bearing for rollingshutters. (DSR-2023 ITEM CODE - 10.7) | Each | 2.00 | 492.35 | 984.7 |
| 40 | STEEL WORK:- Steel work welded in built up sections/ framedwork, including cutting, hoisting, fixing inposition and applying a priming coat ofapproved steel primer using structural steeletc. as required.(a) In gratings, frames, guard bar, ladder, railings,brackets, gates and similar works. (DSR-2023 ITEM CODE - 10.25.2) | Kg | 300.00 | 172.6 | 51,780 |
| 41 | STEEL WORK:- Providing & fixing fly proof wire gauze towindows, clerestory windows & doors withM.S. Flat 15 x 3mm and nuts & bolts complete.(a) Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4 mm aperture on bothsides. (DSR-2023 ITEM CODE - 10.29.2) | Sqm | 34.00 | 1,133.55 | 38,540.7 |
| 42 | FLOORING:- Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer),of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. (DSR-2023 ITEM CODE -11. 39) | Sqm | 122.00 | 1,330 | 1,62,260 |
| 43 | FLOORING:- Providing and laying vitrified floor tiles indifferent sizes (thickness to be specified by themanufacturer) with water absorption less than0.08%and conforming to IS : 15622 , ofapproved make, in all colours and shades, laidon 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) jointing with grey cement slurry@ 3.3kg/sqm including grouting the joints withwhite cement and matching pigments etc.,complete.(a) Size of Tile 600x600 mm. (DSR-2023 ITEM CODE - 11.41.2) | Sqm | 84.00 | 1,553.45 | 1,30,489.8 |
| 44 | FLOORING:- Providing and laying vitrified floor tiles indifferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement :4 coarse sand) jointing with grey cement slurry@ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc.,complete. (b) Size of Tile 800x800 mm. (DSR-2023 ITEM CODE - 11.41.3) | Sqm | 262.00 | 1,885.5 | 4,94,001 |
| 45 | FLOORING:- Providing and laying flamed finish Granite stone flooring in required design and patterns,in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer- in-Charge :(a) Flamed finish granite stone slab Jet Black,Cherry Red, Elite Brown, Cat Eye or equivalent. (DSR-2023 ITEM CODE - 11.55.1) | Sqm | 8.00 | 3,186.7 | 25,493.6 |
| 46 | ROOFING:- Providing and fixing on wall face un plasticisedRigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ringconforming to IS : 5382, leaving 10 mm gap forthermal expansion,(i) Single socketed pipes.(a) 110 mm diameter. (DSR-2023 ITEM CODE - 12.41.2) | Metre | 300.00 | 377.4 | 1,13,220 |
| 47 | ROOFING:- Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories forunplasticised Rigid PVC rain water pipesconforming to IS : 13592 Type A includingjointing with seal ring conforming to IS :5382leaving 10 mm gap for thermal expansion.(a) Single tee without door(i) 110x110x110 mm. (DSR-2023 ITEM CODE - 12.42.4.2) | Each | 15.00 | 221.35 | 3,320.25 |
| 48 | ROOFING:- Providing and fixing precoated galvanised ironprofile sheets (size, shape and pitch ofcorrugation as approved by Engineer- in-Charge) of total coated thickness 0.50mm (basemetal of minimum 0.45mm thickness with totalcoating thickness of 0.05mm) with zinc coating120 grams per sqm as per IS:277, in 240 mpasteel grade, 5-7 microns epoxy primer on bothside of the sheet and polyester top coat 15-18microns. Sheet should have protective guardfilm of 25 microns minimum to avoid scratchesduring transportation and should be supplied insingle length upto 12 metre or as desired byEngineer-in- charge. The sheet shall be fixedusing self drilling /self tapping screws of size(5.5x 55 mm) with EPDM seal, complete uptoany pitch in horizontal/ vertical or curvedsurfaces, excluding the cost of purlins, raftersand trusses and including cutting to size andshape wherever required. (DSR-2023 ITEM CODE - 12.50) | Sqm | 180.00 | 738.65 | 1,32,957 |
| 49 | WATER PROOFING:- Providing and applying integral crystallineslurry of hydrophilic in nature forwaterproofing treatment to the RCC structureslike retaining walls of the basement, watertanks, roof slabs, podiums, reservior, sewage &water treatment plant, tunnels / subway andbridge deck etc., prepared by mixing in theratio of 5 : 2 (5 parts integral crystalline slurry :2 parts water) for vertical surfaces and 3 : 1 (3parts integral crystalline slurry : 1 part water)for horizontal surfaces and applying the samefrom negative (internal) side with the help ofsynthetic fiber brush. The material shall meetthe requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concreteby more than 90% compared with controlconcrete as per DIN 1048 and resistant to 16bar hydrostatic pressure on negative side. Thecrystalline slurry shall be capable of self-healingof cracks up to a width of 0.50mm. The workshall be carried out all complete as perspecification and the direction of the engineerin-charge. The product performance shall carryguarantee for 10 years against any leakage.(a) For vertical surface two coats @ 0.70 kg persqm. (DSR-2023 ITEM CODE - 22.23.1) | Sqm | 495.00 | 472.9 | 2,34,085.5 |
| 50 | WATER PROOFING:- Providing and applying integral crystalline slurry of hydrophilic in nature for water proofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage &water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in theratio of 5 : 2 (5 parts integral crystalline slurry :2 parts water) for vertical surfaces and 3 : 1 (3parts integral crystalline slurry : 1 part water)for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R- 2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydro static pressure on negative side. The crystalline slurry shall be capable of self- healing of cracks up to a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the engineer-charge. The product performance shall carry guarantee for 10 years against any leakage. (b) For horizontal surface one coat @ 1.10 kg per sqm.(DSR-2023 ITEM CODE - 22.23.2) | Sqm | 495.00 | 362.8 | 1,79,586 |
| 51 | FINISHING:- 12 mm cement plaster of mix :(a) 1:4 (1 cement: 4 fine sand). (DSR-2023 ITEM CODE - 13.1.1) | Sqm | 1371.00 | 347.05 | 4,75,805.55 |
| 52 | FINISHING:- 15 mm cement plaster on the rough side ofsingle or half brick wall of mix : (a) 1:4 (1 cement: 4 fine sand). (DSR-2023 ITEM CODE - 13.2.1) | Sqm | 840.00 | 399.45 | 3,35,538 |
| 53 | FINISHING:- Providing and applying plaster of paris putty of2 mm thickness over plastered surface toprepare the surface even and smooth complete. (DSR-2023 ITEM CODE - 13.26) | Sqm | 1345.00 | 262.7 | 3,53,331.5 |
| 54 | FINISHING:- Distempering with oil bound washabledistemper of approved brand and manufactureto give an even shade.(a) New work (two or more coats) over andincluding water thinnable priming coat withcement primer. (DSR-2023 ITEM CODE - 13.41.1) | Sqm | 362.00 | 185.65 | 67,205.3 |
| 55 | FINISHING:- Finishing walls with Premium Acrylic Smoothexterior paint with Silicone additives ofrequired shade (a) New work (Two or more coats applied @ 1.43ltr/ 10 sqm. over and including priming coat ofexterior primer applied @ 2.20 kg/10 sqm). (DSR-2023 ITEM CODE - 13.47.1) | Sqm | 362.00 | 171.1 | 61,938.2 |
| 56 | FINISHING:- Wall painting with acrylic emulsion paint,having VOC (Volatile Organic Compound )content less than 50 grams/ litre, of approvedbrand and manufacture, including applyingadditional coats wherever required, to achieveeven shade and colour.(a) Two coats. (DSR-2023 ITEM CODE -13.82.2) | Sqm | 1188.00 | 137.45 | 1,63,290.6 |
| 57 | SANITARY INSTALLATION:- Providing and fixing water closet squatting pan(Indian type W.C.pan ) with 100 mm sand castIron P or S trap, 10 litre low level white P.V.C.flushing cistern, including flush pipe, withmanually controlled device (handle lever)conforming to IS : 7231, with all fittings andfixtures complete, including cutting and makinggood the walls and floors wherever required:(a) White Vitreous china Orissa pattern W.C. panof size 580x440 mm with integral type foot rests. (DSR-2023 ITEM CODE - 17.1.1) | Each | 2.00 | 6,767.4 | 13,534.8 |
| 58 | SANITARY INSTALLATION:- Providing and fixing white vitreous chinapedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever),conforming to IS : 7231, with all fittingsand fixtures complete, including cutting andmaking good the walls and floors whereverrequired :(a) W.C. pan with ISI marked white solid plasticseat and lid. (DSR-2023 ITEM CODE - 17.2.1) | Each | 9.00 | 6,515.55 | 58,639.95 |
| 59 | SANITARY INSTALLATIONS:- Providing and fixing white vitreous china flatback half stall urinal of size 580x380x350 mmwith white PVC automatic flushing cistern, withfittings, standard size C.P. brass flush pipe,spreaders with unions and clamps (all in C.P.brass) with waste fitting as per IS : 2556, C.I.trap with outlet grating and other couplings inC.P. brass, including painting of fittings andcutting and making good the walls and floorswherever required :(a) Range of two half stall urinals with 5 litre P.V.C.automatic flushing cistern. (DSR-2023 ITEM CODE - 17.5.2) | Each | 3.00 | 18,008.75 | 54,026.25 |
| 60 | SANITARY INSTALLATIONS:- Providing and fixing one piece constructionwhite vitreous china squatting plate with anintegral longitudinal flushing pipe, white P.V.C.automatic flushing cistern, with fittings,standard size G.I. / PVC flush pipe for back andfront flush with standard spreader pipes withfittings, G.I clamps and C.P. brass couplingcomplete, including painting of fittings andcutting and making good the walls and floorsetc. wherever required :(a) Single squatting plate with 5 litre P.V.C.automatic flushing cistern. (DSR-2023 ITEM CODE - 17.6.1) | Each | 9.00 | 9,256.45 | 83,308.05 |
| 61 | SANITARY INSTALLATIONS:- Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mmC.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting andmaking good the walls wherever require:(a) White Vitreous China Wash basin size 630x450mm with a single 15 mm C.P. brass pillar tap. (DSR-2023 ITEM CODE - 17.7.2) | Each | 5.00 | 2,226.35 | 11,131.75 |
| 62 | SANITARY INSTALLATIONS:- Providing and fixing Stainless Steel A ISI 304(18/8) kitchen sink as per IS:13983 with C.I.brackets and stainless steel plug 40 mm,including painting of fittings and brackets,cutting and making good the walls whereverrequired :(a) Kitchen sink without drain board(i) 610x510 mm bowl depth 200 mm. (DSR-2023 ITEM CODE - 17.10.2.1) | Each | 2.00 | 4,940.8 | 9,881.6 |
| 63 | SANITARY INSTALLATIONS:- Providing and fixing 8 mm dia C.P. / S.S. Jetwith flexible tube upto 1 metre long with S.S.triangular plate to Eureopean type W.C. ofquality and make as approved by Engineer - in -charge. (DSR-2023 ITEM CODE - 17.16A) | Each | 9.00 | 394.15 | 3,547.35 |
| 64 | SANITARY INSTALLATIONS:- Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittingscomplete.(a) Semi rigid pipe(i) 32 mm dia. (DSR-2023 ITEM CODE - 17.28.1.1) | Each | 2.00 | 103.9 | 207.8 |
| 65 | SANITARY INSTALLATIONS:- Providing and fixing mirror of superior glass (ofapproved quality) and of required shape andsize with plastic moulded frame of approvedmake and shade with 6 mm thick hard boardbacking :(a) Rectangular shape 453x357 mm. (DSR-2023 ITEM CODE - 17.32.2) | Each | 6.00 | 1,361.8 | 8,170.8 |
| 66 | SANITARY INSTALLATIONS:- Providing and fixing PTMT Bottle Trap for Washbasin and sink.(a) Bottle trap 31mm single piece moulded withheight of 270 mm, effective length of tail pipe260 mm from the centre of the waste coupling,77 mm breadth with 25 mm minimum waterseal, weighing not less than 260 gms. (DSR-2023 ITEM CODE - 17.70.1) | Each | 2.00 | 367.1 | 734.2 |
| 67 | SANITARY INSTALLATIONS:- Providing and fixing PTMT towel rail completewith brackets fixed to wooden cleats with CPbrass screws with concealed fittingsarrangement of approved quality and colour.(a) 600 mm long towel rail with total length of 645mm, width 78 mm and effective height of 88mm, weighing not less than 190 gms. (DSR-2023 ITEM CODE - 17.73.2) | Each | 15.00 | 708.95 | 10,634.25 |
| 68 | WATER SUPPLY:- Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stabilityfor hot & cold water supply, including all CPVCplain & brass threaded fittings, i/c fixing thepipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with onestep CPVC solvent cement and the cost ofcutting chases and making good the sameincluding testing of joints complete as perdirection of Engineer in Charge. :Concealedwork, including cutting chases and makinggood the walls etc.(a) 15 mm nominal outer dia .Pipes. (DSR-2023 ITEM CODE - 18.8.1) | Metre | 450.00 | 497.8 | 2,24,010 |
| 69 | WATER SUPPLY:- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVCplain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. (b) 25 mm nominal outer dia .Pipes. (DSR-2023 ITEM CODE - 18.8.3) | Metre | 375.00 | 627.25 | 2,35,218.75 |
| 70 | WATER SUPPLY:- Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stabilityfor hot & cold water supply including all CPVCplain & brass threaded fittings. This includesjointing of pipes & fittings with one step CPVCsolvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer inCharge : External work(a) 100 mm nominal inner dia. Pipes. (DSR-2023 ITEM CODE - 18.9.9) | Metre | 450.00 | 3,271.7 | 14,72,265 |
| 71 | WATER SUPPLY:- Providing and fixing G.I. pipes complete withG.I. fittings including trenching and refilling etc.: External work(a) 15 mm dia. nominal bore. (DSR-2023 ITEM CODE - 18.12.1) | Metre | 225.00 | 322.15 | 72,483.75 |
| 72 | WATER SUPPLY:- Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.: External work (b) 25 mm dia. nominal bore. (DSR-2023 ITEM CODE - 18.12.3) | Metre | 1050.00 | 467.75 | 4,91,137.5 |
| 73 | WATER SUPPLY:- Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.: External work (c) 50 mm dia. nominal bore. (DSR-2023 ITEM CODE - 18.12.6) | Metre | 2400.00 | 762.15 | 18,29,160 |
| 74 | WATER SUPPLY:- Providing and fixing gun metal gate valve withC.I. wheel of approved quality (screwed end) :(a) 25 mm nominal bore. (DSR-2023 ITEM CODE - 18.17.1) | Each | 3.00 | 622.4 | 1,867.2 |
| 75 | WATER SUPPLY:- Providing and fixing gun metal gate valve withC.I. wheel of approved quality (screwed end) :(b) 50 mm nominal bore. (DSR-2023 ITEM CODE - 18.17.4) | Each | 2.00 | 1,026.65 | 2,053.3 |
| 76 | WATER SUPPLY:- Providing and fixing ball valve (brass) ofapproved quality, High or low pressure, withplastic floats complete :(a) 25 mm nominal bore. (DSR-2023 ITEM CODE - 18.18.3) | Each | 8.00 | 464.05 | 3,712.4 |
| 77 | WATER SUPPLY:- Providing and fixing C.P. brass shower rose with15 or 20 mm inlet :(a) 100 mm diameter. (DSR-2023 ITEM CODE - 18.22.1) | Each | 9.00 | 193.95 | 1,745.55 |
| 78 | WATER SUPPLY:- Providing and placing on terrace (at all floorlevels) polyethylene water storage tank, IS :12701 marked, with cover and suitable lockingarrangement and making necessary holes forinlet, outlet and overflow pipes but withoutfittings and the base support for tank. (DSR-2023 ITEM CODE - 18.48) | Litre | 3000.00 | 11 | 33,000 |
| 79 | Providing and fixing C.P. brass long body bibcock of approved quality conforming to ISstandards and weighing not less than 690 gms.(a) 15 mm nominal bore. (DSR-2023 ITEM CODE - 18.51.1) | Each | 3.00 | 798.85 | 2,396.55 |
| 80 | WATER SUPPLY:- Providing and fixing C.P. brass angle valve forbasin mixer and geyser points of approvedquality conforming to IS:8931 :(a) 15mm nominal bore. (DSR-2023 ITEM CODE - 18.53.1) | Each | 15.00 | 574.3 | 8,614.5 |
| 81 | WATER SUPPLY:- Providing and fixing PTMT bib cock of approvedquality and colour.(a) 15mm nominal bore, 86 mm long. Weighingnot less than 88 gms. (DSR-2023 ITEM CODE - 18.54.1) | Each | 8.00 | 125.6 | 1,004.8 |
| 82 | WATER SUPPLY:- Providing and fixing enclosed type water meter(bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts,rubber insertions etc. (The tail pieces if required will be paid separately) :(a) 80 mm dia nominal bore. (DSR-2023 ITEM CODE - 18. 60. 1) | Each | 2.00 | 3,627.65 | 7,255.3 |
| Schedule total | ₹1,82,96,750.1 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TrackMachineSidingCivilWork.pdf
ATTACHMENT
Electrical Document for electrical
ATTACHMENT
PCECIR_1.pdf
ATTACHMENT
PCECircular208Mixdesignlimits.pdf
ATTACHMENT
TenderBookletT-19DevelopmentoftrackmachinesidingatJNOMRSHBXY.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].