CERTAIN REPAIRS TO FLOORING, TILING, CHAJJA REPAIR AND PLASTERING, PLINTH PROTECTION, RAIN WATER PIPES, ROOFING, JOINERIES, PLUMBING INCLUDING W/S AND SANITARY APPLIANCES ETC AND ALLIED WORKS AT ZONE A AREA OF AGE B/R-I UNDER GE (EAST) LUCKNOW

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thickness below and above ground level, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work old size brick sub class 'B' bricks,straight or curved on plan exc 6 m mean radius,built in in CM (1:6) etc complete all as specified and directed.

M&L for brick work with sub class "B' old size brick straight or curved on plan to any radius in half brick thick built in cement mortar 1:4 etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smooth without using extra cement & with using integral water proofing compound @ 3% by wt of cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound, ISI Marked complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of alkali resistant primer of approved shade/tint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling & applying two coats of white wash, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

S&F non skid ceramic coloured tiles of 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floors, including 15 mm thick screed in CM 1:6 complete all as specified and directed.

All as per above item No. 15 but on vertical surfaces including 10mm thick screed plaser in CM 1:4 and taking down cement plaster /terrazo dado/wall tiling and skirting. etc on brick or stone walls etc

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors joints free, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and directed.

S&F glazed ceramic coloured tiles of 600 x 300mm x 7mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. etc including 10 mm thick rendering in CM 1:4 and taking down cement plaster /terrazo dado/wall tiling and skirting. etc on brick or stone walls etc complete all as specified and directed.

S&F glazed ceramic coloured tiles 450 x 300 x 7mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. etc including 10 mm thick rendering in CM 1:4 and taking down cement plaster /terrazo dado/wall tiling and skirting. etc on brick or stone walls etc complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in plinth protection surface finished fair and even without using extra cement complete all as specified and directed. (Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exc 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3)).

M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) surface finished even and smooth using extra cement as in flooring floor laid in panel area not exc 2 sqm complete all as specified and directed.

Supply only 3 mm thick and 38 wide glass dividing strip complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any motar etc complete all as specified and directed.

M&L granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 including cutting, polishing, rubbring & moulding of edges complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for rendering 15 mm thick on wall in CM 1:3 mixed with water proofing compound complete all as specified and directed. (Note :- The cost of WPC is not included in this item The same shall be paid separetely as supply only)

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per sqm including cleaning surfaces as in sunken complete all as specified and directed.

S&F APP based polymeric membrane mimimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric laid on primed surfaced by forced/torched application complete all as specified and directed.

M&L for PCC 1:7:12 type F2 as in sub base of floor mass filling using 40 mm graded aggregate complete all as specfied and directed.

M&L for 30 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded aggregate using water proofing compound as in sunken floor complete all as specified and directed. (Note:- WPC shall be measured and paid separately 'Only')

M&L for hardcore of gauge of broken stone or boulders not exc 63 mm deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 25mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern/EWC) white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonage pipe etc complete and making good to floor complete all as specified and directed.

S&F in repair vitreous China squatting pan of Orissa pattern of size 580 mm X 440 X 260 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe including lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and directed.

S&F plastic water closet seat, cover white closed pattern with flat bottom & cover & mild steel chromium plated hinging device complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 ltrs capacity with top push buttion inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160m including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink including 40mm dia Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F in repair stainless steel Kitchen plate rack of overall minimum size 750 mm x 900 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S&F SS grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed.

S&F PTMT grating 100mm dia without waste hole (Minimium weight 25 grams) complete all as specified and directed.

S&F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified and directed.

S&F in repair long body 15mm bore bib tap, cast copper alloy, chromium plated fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair 15 mm dia chromium plated fancy type angle valve pipe with capstan head long screwed shank including cp cover plate etc complete all as specified and directed.

S&F in repair 15 mm bore CP brass Central Hole Basin mixture fixed to GI pipe complete all as specified and directed.

S&F in repair 15 mm bore brass CP wall mixer for mixing hot & cold water with provision for over head shower with arm and long bend pipe and wall flanged screwed down for iron pipe etc complete all as specified and directed.

S&F in repair 15mm bore chromium plated Pillar cock screwed down high pressure, with or without lettered Hot ot Cold with long screwed shanks and flynuts screwed for iron pipe complete all as specified and directed.

S&F in repair hand shower (Health faucet) with 1 Mtr flexible tube with wall hook bracket etc, complete set of superior quality complete all as specified and directed.

S&F in repair CP shap dish fancy type fixed with SS screw on wall etc complete all as specified and directed.

S&F in repair toilet paper holder CP fixed complete all as specified and directed.

S&F in repair PVC bath cabinet with 4 mm thick loocking mirror of overall size 560 x 410 mm fixed on wall etc complete all as specified and directed.

S&F in repair glass corner shelf assembly, fancy type, made of 6 to 7mm thick sheet toughened glass of size 250x250mm, fixed with CP brackets, complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair 32mm/ 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S&F in repair cast iron floor trap/nahani trap plan with grating of 100 mm size including jointing to waste pipe with cement joints etc complete all as specified and directed.

Disconnecting existing tanks, exc 250 Ltr & not exc 500 Ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Dismantling PVC water tanks and removing for capacity exc 250 litres & not exc 500 litres etc., complete all as specified and directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered in white colour (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

Dismantling PVC water tanks and removing for capacity exc 500 litres & not exc 1000 litres etc. complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered in white colour (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F in repair 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, complete all as specified and directed.

S&F in repair gun metal gate valve screwed both ends to15mm bore pipe complete all as specified and directed.

S&F in repair 25 mm dia stainless steel curtain rods including brackets and fancy type end knobs, complete, all as specified and directed.

Dismantling of cast iron drain pipe of any dia jointed in lead joints or cement joints and taking out of under floors if required complete all as specified and directed.

S&F 100 mm dia cast iron (sum type) soil waste and vent pipes sand cast in any length with or without laid in wall with cement joints complete all as specified and directed.

S&F 75 mm dia cast iron (spum type) soil waste and vent pipes sand cast in any length with or without laid in trenches or in floor with cement joints complete all as specified and directed.

S&F in repair 100 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S&F in repairs 75 mm bore cast iron bends with acces door of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S&F in repair 75 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S&F 100 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 75 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M&L PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but not exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

Taking down shutters exc 1.0 sqm but not exc 2.0 sqm each and refixing in same opening etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) for filling in bed block of hold fast, back filling of chowkhat etc complete all as specified and directed.

S&F for pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed.

S&F for pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core constructed with block board core and plywood face panels commercial type on both side ISI marked complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F 30 mm thick IInd class hard wood glazed and skelton window or ventilator shutter open rebated and prepared to receive glass etc divited into square with plain chamfered or rounded, mitred beads for securing glass/gauge complete all as specified in SSR Part-I 1991 section 8 clause 8.20 (b) complete all as specified and directed.

S&F mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed 100 mm long complete all as specified and directed.

S&F mild steel pressed handles, oval type ISI marked stove enamelled black complete all as 100 mm size complete all as specified and directed.

S&F 75mm dia butt hinges, ISI market medium weilght cold rolled mild steel complete all as specified and directed.

S&F Anodised aluminium powder coated frame work for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc. complete all as specified and directed.

M&L of 4.8 mm thick sheet glass, ordinary quality in squares exc. 0.5 Sqm in each pane complete all as specified and directed.

M&L for powder coated (min 50 micron) aluminium three track sliding window with extruded profile of top bottom & side track for fixing 5.5mm thick tinted glass fitted with glazing clips and EPDM rubber in two shutters and fixing SS wire mesh in one shutter and powder coated deco grill including roller and handle, maruti locking arrangement complete all as specified and directed. Note:- (a) including 5.5mm thick tinted glass, SS wiremesh, Deco grill etc in this item. (b) Framed section 3 track size = 92x31.75x1.5mm (c) Shutter section size = 40x18x1.55mm Make: Domar or equivalent as approved by GE

S&F in replacement of PVC cabinate shutter as in kitchen with frame including shelves in required sizes at site made out of 18mm thick one side decorative lamination and other side balancing lamination sheet and provision of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets stainless screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings as per site requirmented as per make and specification mentioned as per drawing complete all as specified and directed. Note:- Density of PVC soild sheet should not be less than 575 Kg/cum.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item no 102 but without glazing bars

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M S frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F mild steel helical door spring 150mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Eye door viewer (Magic Eye) of suitable size fixed with panneled door shutter complete all as specified and directed.

S&F in repair 300mm long Stainless steel six peg hanger chromium plated complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters; walk ways, railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including welding work complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and directed.

S&F ball catcher with 8 mm dia steel bal and brass body and strike plate magnet ball catcher for cup board shutters complete all as specified and directed.

Demolition of reinforced cement concrete in floors ,beams, chajjas,landing slab in any position or height and similar suspended works complete all as specified and directed.

M&L for RCC 1:1.5:3 type B-1 nominal mix (using 20 mm graded stone aggrigate) as in slab, chajjas, beam etc complete all as specified and directed.

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exc 200mm thick complete all as specified and directed.

M&L TMT bar 8 to 10mm dia and over, cut to length, bent ot shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) including welding, rivetting etc complete all as specified and directed.

Repairing of RCC projections chajjas, roofs, facia etc by necessary preparation, scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC and providing cement concrete (1:1.5:3) using 12.5 mm graded crushed stone aggregate including necessary form work and reinforced with chicken wire mesh and rendering in cement mortar 1:3 using coarse sand in patches area not exceeding 5 sqm each and thickness of RCC member not exceeding 70mm including applying two coats of finishes as provided to the existing surfaces to match with the existing surfaces in at any height complete all as specified and directed.

M&L for in repair block board, 18/19mm thick, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame work complete all as specified and directed.

S&F 0.9mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructionas complete all as specified and directed.

S&F in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F in repair 32 mm dia of discharge pipe bottle trap of PTMT having minimum water seal of 25 mm (Minimum weight 32 mm -260 gms/40 mm-270 gms) etc complete all as specified and directed.

S&F in repair long body 15mm bore two-way bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

M&L chequred cement concrete tiles 30 cm x 30 cm x 25 mm thick set and jointed and pointed in neat cement slurry with grey cement and pigment in floors including 20 mm screed bed in CM 1:6 complete all as specified and directed.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc complete all as specified and directed.

S&F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps as directed 6 Kg/Sqcm complete all as specified and directed.

S&F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes complete all as specified and directed.

Dismantling textile covering incl frames (if any) and cover fillets (measured flat and not girthed) complete all as specified and directed.

S&F 605 x 605 mm GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling sectin (Not exc 1.2m length) of 0.55 mm thick having kurled web of 50mm and flanges of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including hangers 3 mm dia gI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia 40mm long complete all as specified and directed.

M&L providing and fixing gypsum boad 12 mm thick in ceiling fixed with screw as per manufactures instruction complete all as specified and directed.

Removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removing the same to the places complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B1 using 12.5 mm graded aggregate as in roof for maint. the uniform slope etc any thickness at any height and in any position complete all as specified and directed.

M&L 20 mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces on other than fair face surface, surface finished even and smooth without using extra cement using waterproofing compound complete all as specified and directed.

M&L for roof treatment with polymeric water proofing membrane consisting of following complete all as specified and directed :- (a) Applying bituminous primer conforming to IS 702-1988 @ 1.20 Kgs/ sqm. (b) APP modified bitumenous membrane minium weight 3 kg/sqm and minimum 3 mm thick reinforced with polyester non wove fabric ( wt. not less than 150 gms/sqm) laid on primed surface by heat process, over laps of 100 mm shall be sealed / fused by flame torch application as per manufacturer instructions. (c) Applying two coat of bituminous bases aluminium paint @ 0.2 kgs/sqm over APP membrane.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping steps bed blocks/roof gola etc complete all as specified and directed.

S&F solid PVC wall lining consisting of 5 mm thick single side prelam PVC sheet used instead of plain colour sheet as per specification complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F in repair vitreous china floor hung WC with flushing cistern, UF seat cover, hinges, accessories set of size 375 x 650 x 800/370 x 645 x 810 mm fixed to wall/floor with P/S trap complete as per manufacture's instructions complete all as specified and directed.

S&F in repair vitreous china wall hung WC, UF seat cover, hinges, accessories set of size 360 x 570x x 360 mm fixed to wall/floor with P/S trap complete as per manufacture's instructions complete all as specified and directed.

S&F in repair single piece slim concealed cistern body with installation kit & s type, drain pipe, connection set for wall hung WC complete including connection with GI pipes or connection pipe as per manufacture's instructions complete all as specified and directed.

S&F in repair vitreous china table top Wash Hand Basin of size 635 x 430 x 190 mm with bottle trap complete all as per manufacturer's instruction complete all as specified and directed.

S&F single lever Basin mixer without popup waste system with 450 mm long braided holes etc complete all as specified and directed.

S&F in repair Towel ring 200mm dia superior quality fixed complete all as specified and directed.

M&L for preparation of old surfaces (plastered or unplastered) of walls/ceiling including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of plastic paint complete all as specified and directed.

S&F in repair cascade type flush kit any make (existing on ground) complete all as specified and directed

S&F in repair 15 mm dia spindle for bib taps, angle valve and pillar taps etc as required including taking down existing spindle carefully and fixed the same in positioncomplete all as specified & directed.

M&L for 2nd class hard wood plain, solid straight chowkhats and frames, wrought framed rebated an the solid, rounded or chamfered put together with glue pinned at joints supplied and fixed etc complete all as specified and directed

S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Taking out existing aluminium shutter any type and refixing of aluminium shutter fixed with glazed /particle board in panels including all necessary repair and replacing the aluminium snap beading, rubber packing, glazing clip etc complete all as specified and directed

S&F in repair 1.00 mtr long any anodized aluminium door seal fixed with screw complete all as specified and directed

M&L for repair to steel window shutter by replacing worn out hinges with box type hinges and worn out portion such as glazing bars fittings and fixture positioning of shutter etc and cleaning the window surrounding and renewal of fittings and fixture (unserviceable) including greasing welding, complete all as specified and directed

M/S RAJ INTERIORS

M/S SWATI CONSTRUCTION

R K CONTRACTOR AND SUPPLIERS

M/s Sachkhand Traders

QUALITY CONSTRUCTIONS CO

Yadav Builders

M/s R.K.Traders

m/s raghubar dayal

Rakesh Traders

Comnet technologies

Abode Artisan Enterprises

R P construction company