ADDN ALTN RENOVATION TO CERTAIN TOILETS, CAOS QTRS, JCOS NCOS ACCN AND SERVICE OFFICERS MD ACCN AT KHADAKWASALA

Amount

Note: This is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

BUILDING (CIVIL) WORK

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises, complete all as specified and directed.

S&F joint free ceramic coloured tiles, 7 to 8mm thick grade B II matt superior finish first quality, (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc, laid over and including 15 thick screed bed in cement mortar 1:6 and set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and as directed.

S&F glazed coloured ceramic joint free tiles over vertical surface of wall, 350x 250x 7mm/ 450x 350x 7mm thick (or nearest size), set and jointed in neat cement slurry and pointed in coloured cement to match with and including backing coat of 10mm thick in cement mortar (1:4) complete all as specified and directed.

Demolition cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for 50mm thick cement concrete (1:4:8) type D-1 using 20 mm graded stone aggregate as in sub base of flooring/ hard standing/ path and finishing the surface even and fair without using extra cement complete all as specified and as directed.

M&L for 18/19mm thick, Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work for kitchen cabinate, cupboard etc. complete all as specified and as directed.

M&L for 12mm thick plywood grade BWR, type BB, fixed with screws to timber frame work for kitchen cabinate, cupboard etc. complete all as specified and as directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (When open) is 30 mm, complete all as specified and as directed.

S & F for ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F 100 mm long brass handle, cast type polished bright for cupboards, cabinate complete all as specified and as directed.

M & L for Ist class hard wood (Teak), plain fillets,square,rectangular or triangular in section, area not exceeding 3Sqcm, clean sawn, secured with nails or brads complete all as specified and as directed.

M & L for IInd class hardwood (Bijasal/ Benteak/ Laurel/ Sal), plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

Taking down of chowkats or frames with shutters (with out taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and as directed.

Taking down of chowkats or frames with shutters (with out taking off shutters from the frames) exceeding 1.5sqm but not exceeding 4sqm each complete all as specified and as directed.

Taking down shutter of any description exceeding 1 sqm and not exceeding 2sqm each complete and removing from site complete all as specified and as directed.

S&F IInd class hardwood (Bijasal/ Benteak/ Laurel/ Sal), 30mm thick, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), supplied and fitted to chowkats complete all as specified and as directed.

S & F for 2nd class hard wood (Bijasal/ Benteak/ Laurel/ Sal), 35 mm thick, glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and as directed.

S & F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staple, complete all as specified and as directed.

S & F for butt hinges, medium weight, cold rolled Mild Steel, 100mm, ISI marked, complete all as specified and as directed.

S & F for 200mm long Mild Steel barrel tower bolts, Stove enamelled black, with bright bolt and fixed, complete all as specified and as directed.

S & F for extruded aluminium alloy handle fabricated type anodised of size 100mm, complete all as specified and as directed.

S & F for 300mm long mild steel sliding door bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and as directed.

S & F floor door stopper of aluminum alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor having overall 150mm long cover plate complete all as specified and as directed.

Demolition of RCC in ground floors and pavings not exceeding 15 cm thickness, reinforcement cut as required to facilitate demolition, complete all as specified and as directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and removing rubbish from the premises complete all as specified and as directed.

M & L for 25-30mm thick machine cut unpolished cudappah stone for cooking platform below granite stone and the like including necessary jointing and pointing and making good to disturbed surfaces complete all as specified and as directed.

M & L for 25-30mm thick machine cut polished cudappah stone as in vertical support for cooking platform and the like including necessary jointing and pointing and making good to disturbed surfaces complete all as specified and as directed.

M&L 18-20mm thick Granite (of any type) work as in cooking platforms and like, machine cut and mirror polished fixed with neat cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L 18-20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (Veneering to wall) over and including 12mm thick cement mortar 1:3 and pointed in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone complete all as specified and as directed.

Labour only for chamfering or rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situations, thickness of slab not exceeding 25mm, complete all as specified and as directed.

S&F in repairs, stainless steel sink with drainage board, made out of 1mm thick sheet for kitchen with plugs, washer and waste in repairs including in cement mortar to dwarf wall or including fixing cantilever brackets and connection union to pipe overall size not less than 915mm x 460mm bowl size not less than 410mm x 330mm x 160mm complete all as specified and as directed.

S & F in repairs vitreous china wash basin, white, flat back, size 550x400mm with brackets, excluding taps, waste chain and plug and porcelain stopper but including cutting for & pinning in ends of brackets, waste fitting,PTMT 32mm dia, PVC connection 600mm complete all as specified and as directed.

S & F in repair, vitreous china wash down water closet (Pedestal Pattern) with 'P' or 'S' trap, white in colour including fixing bolts, connection to drain and to flushing pipe with and including low level PVC valve less symphonic action type flushing cistern of 10 Litres capacity white colour with inlet, ball valve float and PVC flush pipe 32mm dia, PVC connection 600mm , with white seat cover closed pattern with flat bottom and cover and MIld steel chromium plated or hinging device complete all as specified and as directed.

S & F in repairs, pillar taps, fancy type, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and as directed.

S&F in repairs, bib taps, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and as directed.

S&F in repairs, two way bib cock, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and as directed.

S&F in repairs, angular stop valve, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore pipe with long shank complete all as specified and as directed.

S&F in repairs, for shower arm, 15mm dia bore, 450mm long with 90 degree bend for rain showers complete all as specified and as directed.

S&F in repairs, 15mm dia bore shower health faucet chromium plated with 01 Meter long flexible tube and suitable wall hook complete all as specified and as directed.

S&F in repairs, wall mixer brass CP for mixing hot & cold water with connection to over head shower with 115mm long bend pipe wall flange, screwed down for iron pipe and fixed for 15mm dia bore pipe complete all as specified and as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long complete all as specified and as directed.

S&F in repairs, corner glass shelf (with back) chromium plated complete all as specified and as directed.

S&F in repair, Brass chromium plated tubular towel rail, 20mm dia , D type, 60cm long between flanges complete all as specified and as directed.

S & F, in repair, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap with and including high level PVC valve less syphonic action type flushing cistern of 10 Lit capacity white in colour with inlet, ball valve float and PVC flush pipe 32mm dia and PVC connection 600mm suitable for 15mm dia bore GI pipe or ferrule including provision of cement concrete (1:5:10), type E-2, using 40mm graded stone aggregete complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing for 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing for 20mm bore of pipe complete all as specified and as directed.

S & F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and as directed.

S & F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and as directed.

Refixing of 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and as directed.

Refixing of 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and as directed.

Dismantling of 100mm dia bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S & F 110 mm dia bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls etc using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S & F 110 mm dia bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or under floor etc using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S & F 110 mm dia PVC (SWR) bend any radius with oval access door including jointing material complete all as specified and as directed.

S & F 110mm dia PVC (SWR) junction single, (Single T) equal or unequal including jointing material complete all as specified and as directed.

S & F PVC (SWR) vent cowl for 110mm dia bore including jointing material complete all as specified and as directed.

S & F 110mm dia PVC (SWR)branch piece, single (single Y) equal or unequal including jointing material complete all as specified and as directed.

S & F 75 mm dia bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls etc using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S & F 75 mm dia bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or under floor etc using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S & F 75mm dia PVC (SWR) bend any radius with oval access door including jointing material complete all as specified and as directed.

M&L 75 mm dia UPVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for 100mm dia cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water to remove dust etc complete all as specified and as directed.

M & L for rendering 15mm thick on brick or concrete surfaces in cement mortar 1:6 surface finihsed even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 10mm thick on concrete surfaces in cement mortar 1:4 on ceiling, surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over 3mm thick layer of wall care putty on wall complete all as specified and as directed.

M&L for complete removal of existing treatment on wall and applying two coats of Distemper oil emulsion over and including 3mm thick layer of wall care putty on wall complete all as specified and as directed.

M&L for complete removal of existing treatment on ceiling and applying two coats of Distemper oil emulsion over and including 3mm thick layer of wall care putty on wall complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceilings and applying three coat of white wash on ceilings over and including 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Disconnecting of existing water storage tanks of capacity exceeding 500 Ltrs but not exceeding 1000 Ltrs, and removing to store complete all as specified and as directed.

M & L for Rotational moulded polyethylene water storage tanks of capacity 1000 Ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

M & L for Rotational moulded polyethylene water storage tanks of capacity 500 Ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

S&F in repairs 20mm dia of ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs, 20 mm dia gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

M&L for taking down existing water proofing treatment of any description and layers from wall/roofs including screed bed or bedding layers of mortar of any type complete and cleaning the surfaces free from dust and scrubbing down with water complete all as specified and clearing the premises by removing dust, foreign material, rubbish off the site to a distance not exceeding 100m complete all as specified and as directed.

M&L for Water proofing treatment to RCC roof slab, walls, chhajjas etc and shall be carried out as specified below and as directed by Engineer-in-Charge:- (a) Providing 20 mm average thickness of screed layer on RCC roof slab in cement mortar ( 1:4 ) including water proofing compound @ 3% by weight of cement. (Note :- WPC will be measured and paid for separatly) (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & applying evenly a coat of approved bituminous primer @ 0.20 Kg/sqm of area. (c) Providing APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 Kg/sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engineer-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/sqm on the top of membrane surfaces complete all as specified and as directed.

Supply only integral water proofing compound ISI marked complete all as specified and as directed.

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and as directed.

Material and lobour for roof tiles, Mangalore Pattern, interlocking at side joints laid dry complete all as specified and as directed.

Lobour only for laying/fixing of roof tiles, Mangalore Pattern, interlocking at side joints laid dry complete all as specified and as directed. (MP tiles retrieved from dismantling to be reused)

Material and lobour for ridge tiles, Mangalore Pattern of roof tiles, set and jointed in cement mortar 1:6 complete all as specified and as directed.

Lobour only for ridge tiles, Mangalore Pattern of roof tiles, set and jointed in cement mortar 1:6 complete all as specified and as directed.(Ridge tiles retreived from dismantling shall be reused)

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exceeding 15 cm complete all as specified and as directed.

M & L for 2nd class hard (Bijasal/ Benteak/ Laurel/ Sal) wood clean sawn battens at 30 cm centre, sectional area exceeding 5 but nor exceeding 15 sqcm, complete all as specified and as directed.

Labour only for fixing of 2nd class hard wood clean sawn battens at 30 cm centre, sectional area exceeding 5 but nor exceeding 15 sqcm, complete all as specified and as directed.(Battens retreived from dismantling shall be reused).

Dismantling plian or corrugated steel sheeting, any guage, thickness, including Nanital or similar pattern roof covering complete all as specified and as directed.

Supply and fixing 0.63mm thick galavanised, corrugated mild steel sheeting with two corrugations side laps, fixed with 'L' hook or 'J' hook bolts and washer in roofs walls etc with grade of zinc coating 275 complete all as specified and as directed.

Supply and fixing 0.63mm thick plain galvanised mild steel sheeting in ridges, hips, valley, gutters, drips and straight flashings(length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.

Dismantling of boarding, any description and in any position with nails complete all as specified and as directed.

M&L for 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 20mm to 25mm thick and fixed with 20mm laps complete all as specified and as directed.

Labour only for fixing of old 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 20mm to 25mm thick and fixed with 20mm laps complete all as specified and as directed.(Boarding retreived from dismantling shall be reused)

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M & L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1, wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and as directed.

M & L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1, wall not exceeding 10 cm in width and built in cement mortar 1:4 complete all as specified and as directed.

M&L 15mm thick cement plastering on concrete surfaces in cement mortar 1:4, finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and as directed.

M&L for preparing the surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treating with two coats of cresote oil complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for 4mm thick asbestos cement plain sheet 600mm x 600mm for ceiling on anodized aluminium grid work 610 x 610 mm with using 36.5mmx23.5mmx1.5mm thick main tee, 23.5 x23.5mmx1.28mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 610x610mm on RCC slopping, including two coats of white wash and preparation of surfaces complete all as specified and as directed.

M&L for complete removal of existing treatment on wall and applying two coats of cement based paint complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in roof kerbs slightly rounded or chamfered on edges including necessary form work complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping, eaves filling etc slightly rounded or chamfered on edges including necessary form work complete all as specified and as directed.

Surface eacavation not exceeding 30cm & averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding. 1.5 m in depth for foundation etc or for shafts, wells, manholes, pier holes, laying of cable & pipes etc not exceeding 10 sq m on plan not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding. 1.5 m in depth for foundation etc or for shafts, wells, manholes, pier holes, laying of cable & pipes etc not exceeding 10 sq m on plan not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding. 1.5 m in depth for foundation etc or for shafts, wells, manholes, pier holes, laying of cable & pipes etc not exceeding 10 sq m on plan not exceeding 1.5m in depth and getting out in soft / disintegrated rock complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick as in soil complete all as specified and as directed.

Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m from the starting point complete all as specified and as directed.

M&L hard core of broken stone of gauge not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface etc complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:3:6) type C-1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for dubbing out average 15mm thick on irregular face of walls in CM 1:4 ( when specifically ordered in writting) complete all as specified and as directed.

M&L for rendering 15mm thick on stone masonry surfaces or surface other than fair faces of brick work in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of old surfaces of ceilings and applying two coats of white wash on ceilings complete all as specified and as directed.

M&L preparing old plastered surfaces of ceiling and applying two coats of oil bound distemper white or tinted over on ceiling complete all as specified and as directed.

M&L for preparation of surfaces of wall and applying two coat of weather shield acrylic apex paint complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M & L for preparing new/untreated surfaces of steel of any description exceeding 10cm width or grith and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M & L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and as directed.

M&L for Dark shade vitrified ceramic tiles flooring 10mm thick (square/rectangular) polished laying in design pattern (Pattern approved by GE) area of each tiles not exeeding 0.36 Sqm in floor etc laid bedded over and including 20mm thick CM (1:6) bedding & pointed in white/coloured cement to match coloured tiles etc complete all as specified and as directed.

M&L vitrified ceramic tiles 10mm thick and 10 cm height as in vertical surfaces such as skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick backing plaster in CM (1:4) complete all as specified and as directed.

M & L for machine cut kota stone slab prepolished (Mirror Polished) flooring 20-25mm thick over and including cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

S&F non skid ceramic coloured tiles, 7 to 8mm thick, (square/rectangular), area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc, laid over and including 15 thick screed bed in cement mortar 1:6 and set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and as directed.

Disconnecting existing tanks of capacity exceeding 500litres & not exceeding 1000 litres, setting aside (or lowering if required) for repairs, cleaning, etc. & hositing if required reconnecting & re-fixing in position. (Cleaning repairing etc. measured separately) complete all as specified and as directed.

S&F Stainless steel plate utensil rack of size 900mm x 600mm x 300mm of 1mm thickness stainless steel sheet, SS Screw & Round pipe, grade of steel SS-304 complete all as specified and as directed.

S&F bathroom cabinet of size 450 mm X 300mm with door and shelves and mirror in front side of door and fixed to wall complete with washer etc complete all as specified and as directed.

S & F 50mm PVC HDPE pipe fixed complete to wall or laid in floor with fittings etc complete all as specified and as directed.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (min. weight 40 gms) complete all as specified and as directed.

S&F in repairs, Towel Ring of CP fixed with & including CP brass screws & wooden / plastic cleats (min. weight 90 gms) complete all as specified and as directed.

M&L in repairs chromium plated Soap dish complete all as specified and as directed.

S&F in repairs Brass chromium plated Towel rack 24" complete all as specified and as directed.

S&F in repairs, Overhead shower rose and 450mm long swivel shower arm chromium plated and fixed complete all as specified and as directed.

S & F for Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

M & L for cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in stone, concrete block or slab wall complete all as specified and as directed.

S&F aluminium powder coated three track sliding window with 5.5 mm thick tinted glass shutters and stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make listed in appendix 'C', complete all as specified and as directed. (a) Bottom frame - 20620, (b) Top frame and vertical - 20621 (c) Handle (side) - 20606, (d) Shutter inter lock - 20724, (e) Shutter top & bottom - 20844 & (f) glazing clip -19352

S&F for aluminium anodised powder coated louver ventilator using rectangular tube of size 63.5x25x1.5mm along with 4mm thick design glass including provn of exhaust fan etc complete all as specified and as directed. .Note:- Exahaust fan will be paid separetaly

Dismantling wrought iron or mild steel work of any description not other wise provided for, complete all as specified and as directed.

S & F framed work such as grills, grating etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings and similar work conforming to Fe-290 Gd E-165 complete all as specified and as directed.

Taking down shutter of any description exceeding 2sqm each complete and removing from site complete all as specified and as directed.

S&F 35mm thick second class hard wood (Bijasal/ Benteak/ Laurel/ Sal) factory made plain framed panelled door shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board medium density with commercial veneering both face. The size of rail and stile shall be as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S & F for flush shutters 40mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides with and including 5mm thick lipping complete all as specified and as directed.(Decorative lamination veneer sheet measured and paid seperetely)

M&L for 0.9mm thick decorative laminate type-I, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality including removing old broken glass from existing shutter by removing steel flat or aluminium glazing beading and refixing the same flat / aluminium glazing beading, necessary clipping with steel pins area exceeding 0.5 sqm each pane complete all as specified and as directed.

S & F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed.

S & F stainless steel handle, cast type, of size 150mm and fixed with chromium screws complete all as specified and as directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L 12mm thick Veneered decorateive plywood, grade 1 (with BWR resin) with decorate face veneers on both faces; fixed with screws to timber frame work complete all as specified and as directed.

M & L for french polishing on wooden surfaces of any description, including cleaning and preparing the surfaces including a coat of wooden filler on new works with two or more coats complete all as specified and as directed.

M & L for PCC (1:4:8) type D-2, using 40 mm graded stone aggregate as in foundations, filling and mass-concrete complete all as specified and as directed.

M & L for 50mm thick PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in flooring, surface finished even and smooth without using extra cement all as specified and as directed.

M&L preparation of newly plastered wall surface and appplying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

Supply and fixing in position, framed & hung as gates, ornamental and intricate design, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and as directed.

M&L for 60mm thick machine pressed pre-cast cement concrete interlocking paver blocks with grey cement and pigment, rubber moulded any shape and size confirming to IS 15658-2006, M-35 grade as in floor/pavement laid over and including 30mm thick crushed stone sand complete all as specified and as directed.

M & L for PCC (1:2:4) type B-2, using 40 mm graded stone aggregate as in foundations, filling and mass-concrete for posts, complete all as specified and as directed.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specially provided for, complete all as specified and as directed.

M&L Machine cut cuddapah stone slab 30 to 35mm thick over cement screed base, laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 30-40mm thick over cement screed base, laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L 30 mm thick rough dressed shahabad stone slab flooring, laid, bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/ hard standing/ path and finishing the surface even and fair without using extra cement, complete all as specified and as directed.

M & L for providing cement concrete of type B-1 (1:2:4), using 20 mm graded stone aggregates, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including form work, complete all as specified and as directed.

M & L for TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia etc complete all as specified and as directed.

M & L for TMT bars 6mm dia and over and upto 8mm as in reinforcement cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia.etc complete all as specified and as directed.

M & L for TMT bars 5mm dia and over and upto 10mm as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia.etc complete all as specified and as directed.

Cutting holes into or through stone masonry walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required for superficial area not exceeding 150 Sqcm complete all as specified and as directed.

Drilling holes for bolts, pipes, etc. not exceeding 25mm dia complete all as specified and as directed.

M&L racking out joints/pointing of random or polygonal rubble masonry, uncoursed or brought upto courses in cement mortar and flush pointing in CM 1:4, complete all as specified and as directed.

M&L racking out joints/pointing of random or polygonal rubble masonry, uncoursed or brought upto courses in cement mortar and raised pointing in CM 1:3, complete all as specified and as directed.

Taking down shutter of any description not exceeding 1 sqm each and removing from site complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S & F for 2nd class hard wood (Bijasal/ Benteak/ Laurel/ Sal) 30 mm thick, glazed and skeleton shutters open rebated and prepared to rceieve glass with devided in to squares with plain, chamfered or rounded, mitred and rebated sash bars any numbers fitted with cut and mitred beads for securing glass,etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (b) complete all as specified and as directed.

S&F 2nd class hard wood (Bijasal/ Benteak/ Laurel/ Sal) small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles not exceeding 200 cu. cm each complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares, not exceeding 0.5 sqm each pane complete all as specified and as directed.

S&F Figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and as directed.

S & F for butt hinges, medium weight, cold rolled Mild Steel, 75mm, ISI marked, complete all as specified and as directed.

S & F for Aluminium handles, size 100mm, cast type, anodised complete all as specified and as directed.

S & F for Aluminium handles, size 150mm, cast type, anodised complete all as specified and as directed.

S & F for Aluminium anodised, barrel tower bolts of extruded section and fixed of size 100 mm, complete all as specified and as directed.

S & F for Aluminium anodised, barrel tower bolts of extruded section and fixed of size 150 mm, complete all as specified and as directed.

S & F for 200mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

S & F 20mm dia MS chromium plated curtain rod with fixing brackets, stops, rollers etc complete all as specified and as directed.

S & F aluminium anodised tubular towel rail 20mm dia for cupboards and fixed complete all as specified and as directed.

M & L for 2nd class hard wood (Bijasal/ Benteak/ Laurel/ Sal) plain fillets, square, rectangular or triangular in section, area not exceeding 13Sqcm but not exceding 25Sqcm, wrought, secured with screws complete all as specified and as directed.

M&L for 12mm thick, Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work for shutters etc. complete all as specified and as directed.

S&F for 20mm dia tank Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) complete all as specified and as directed.

S&F in repairs, stop valve, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and as directed.

S&F brass chromium plated shower roses 125mm size with or without swivel joints any size including fixing to steel pipe or union complete all as specified and as directed.

S & F for Unplasticized PVC pipes 50mm dia bore, of pressure rating 10 kgf/sqcm fixed complete to walls, ceiling or floors etc complete all as specified and as directed.

S&F stainless steel sink, made out of 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, washers, including fixing cantilever cast iron brackets and connection union etc. to pipe overall size not less than 495mm x 420mm bowl size not less than 410mm x 330mm x 160mm complete all as specified and as directed.

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm, fixed to plug with CP brass screw and complete all as specififed and as directed.

Dismantling of 75mm dia bore cast iron drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S&F in repair for 75mm dia PVC (SWR) branch piece single (single Y) equal or unequal with access door complete all as specified and as directed.

S&F in repair for 110mm dia PVC (SWR) branch piece single (single Y) equal or unequal with access door complete all as specified and as directed.

Demolition & breaking up drain pipes (SWG, AC or RCC pipes) set in cement mortar 100mm dia complete all as specified and as directed.

Demolition & breaking up drain pipes (SWG, AC or RCC pipes) set in cement mortar 150mm dia complete all as specified and as directed.

Demolition & breaking up drain pipes (SWG, AC or RCC pipes) set in cement mortar 200mm dia complete all as specified and as directed.

Demolition & breaking up drain pipes (SWG, AC or RCC pipes) set in cement mortar 300mm dia complete all as specified and as directed.

M & L for providing plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in bed to drain pipes 75mm dia in including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and as directed.

M & L for providing plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in bed to drain pipes 100mm dia in including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and as directed.

M & L for providing plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in bed to drain pipes 150mm dia in including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and as directed.

M & L for providing plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in bed to drain pipes 200mm dia in including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and as directed.

M & L for providing plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregates as in bed to drain pipes 300mm dia in including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and as directed.

S&F Reinforced cement concrete (Hume) pipe of bore dia 100 mm , class NP2, laid and jointed with collar in cement mortar 1:4 complete all as specified and as directed.

S&F Reinforced cement concrete (Hume) pipe of bore dia 150 mm , class NP2, laid and jointed with collar in cement mortar 1:4 complete all as specified and as directed.

S&F Reinforced cement concrete (Hume) pipe of bore dia 200 mm , class NP2, laid and jointed with collar in cement mortar 1:4 complete all as specified and as directed.

S&F Reinforced cement concrete (Hume) pipe of bore dia 300 mm , class NP2, laid and jointed with collar in cement mortar 1:4 complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100mm dia pipe, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm dia pipe, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 200mm dia pipe, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 300mm dia pipe, complete all as specified and as directed.

S&F 100mm dia asbestos cement pipes in any length with cement joints as in vent; fixed to walls including taking out old pipe complete all as specified and as directed.

M & L for stack clamps for 100 mm dia bore pipes made out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

M&L for precast RCC 1:2:4 type B-1 (using 20mm grade stone aggregate) as in cover slabs for manholes set in CM (1:6) complete all as specified and as directed. (Note : Reinforcement shall be measured & paid separately) etc complete all as specified & directed .

M & L for rendering 5mm thick on concrete surfaces in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 with WPC, finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 15mm thick on other than fair faces of brick surfaces in cement mortar 1:4 with WPC, finished even and smooth without using extra cement complete all as specified and as directed.

M & L for PCC (1:3:6) type C-2, using 40 mm graded stone aggregate as in foundations, filling and mass-concrete complete all as specified and as directed.

M & L for PCC (1:2:4) type B-1, using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

Dismantling of unframed work, timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and as directed.

Dismantling timber fillets in framed work , rails, posts, rafters, purlins, etc under 40 sqcm in section complete all as specified and as directed.

M&L for wrought 2nd class hardwood (Bijasal/ Benteak/ Laurel/ Sal), in scantlings in repairs, to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions to store complete all as specified and as directed.

M&L for preparing tile battens of any size and spacing and treated all over (measured overall on one side only spaces not deducted) with two coats of cresoting oil etc complete all as specified and as directed.

M&L for 2nd class hardwood (Bijasal/ Benteak/ Laurel/ Sal), clean sawn eaves boarding 25mm thick, supplied & fixed with nails in any situation (except flooring and skirting) with butt joints complete all as specified and as directed.

M&L for cutting grooves in brick / stone wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and as directed.

Demolition of reinforced cement concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed.

M&L for complete removal of existing treatment on wall and applying two coats of Distemper oil emulsion over a coat of primer on plastered and other surfaces with alkali resistant primer over 3mm thick layer of wall care putty on wall complete all as specified and as directed.

M&L for complete removal of existing treatment on ceiling and applying two coats of Distemper oil emulsion over a coat of primer on plastered and other surfaces with alkali resistant primer over 3mm thick layer of wall care putty on ceiling complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old plastered/concrete surfaces of walls and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper on walls complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceilings and applying two coats of oil bound distemper on ceilings complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards /slabs /blankets, any thickness, including cover fillets and refixing in position complete all as specified and as directed.

S & F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS -1161-1979 grade St.-240 complete all as specified and as directed.

S & F for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and as directed.

M&L for 150mm thick cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in hard standing and finishing the surface even and smooth without using extra cement, including necessary form work complete all as specified and as directed.

M&L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ in concrete slab of 150mm thick complete all as specified and as directed.

S & F for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and as directed.

S & F for framed work Fe 410-W ( Gde E-250) quality 'A' as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S & F for 1mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S & F for 6mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber /GI /Aluminium framework with screws as in ceiling complete all as specified and as directed.

M & L for random rubble walling, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, complete all as specified and as directed.

M & L for cutting openings, through stone/ brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.to store and rubbish not exceeding 50m, complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed.

S&F Anodised aluminium snap grid (605mm x 605mm) frame work with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and including necessary bolts, nuts and washers for false ceiling. The main and cross tees shall be jointed at junction/crossings with anodized aluminium angle bracket of size as indicated, if not indicated it shall be 15mm x l5mm x 1.5mm, weighing 0.12 Kg per running metre, fixed with sutiable mild steel, bolts nuts and washers. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size as indicated, if not indicated it shall be 40mmx25mmx2mm, weighing 0.36 Kg per running metre, complete all as specified and as directed.

E/M WORK

Supply, laying, testing and commissionnig of UG LT cables 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminum conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cable including material and labour for all jointing/connecting material as required size, cables laid in trenches /ducts /under plinth floors passing through pipes etc, fixed on wall of size 4 core 10Sqmm complete all as specified and as directed.

Supply, laying, testing and commissionnig of UG LT cables 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminum conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cable including material and labour for all jointing/connecting material as required size, cables laid in trenches /ducts /under plinth floors passing through pipes etc, fixed on wall of size 2 core 6Sqmm complete all as specified and as directed.

Supply & fix DWC HDPE Pipes 40 mm dia ISI marked with all fittings for cable protection when laid in trenches, across roads, culverts, pavements and marshy land etc and fixed to pole by flat iron clamps, nut, bolt, washers of suitable size complete all as specified and as directed.

M & L for cutting road/path/floor of width 45cm and depth as per specification for laying GI pipe medium grade and making good with PCC 1:2:4 type B-1 using 20mm graded coarse stone aggregates and matching with the existing chequerred tiles/road/PCC in case of any damage, complete all as specified and as directed.

Supply and laying sub class ‘B’ bricks well burnt for cable protections, laid flat with length equal to width of brick over cable perpendicular to length of cable complete all as specified and as directed.

Supply and filling dry river sand with including gently punning around cables in trenches for cable protection complete all as specified and as directed. .(Note : Punned thickness shall be measured)

Taking down existing service connection of any type including GI wire with insulators complete all as specified and as directed.

Taking down unserviceable sub main wiring of any type and size with teak wood battens/Casing capping/PVC Conduit/ and making good disturbed surface complete all as specified and as directed.

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2.5 Sqmm , 1100 Volts grade in and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and as directed. . (Note: Two runs of 2.5Sqmm cable with 01run of 2.5 Sqmm earth wire along with casing caping shall be measured as one RM).

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and as directed. . (Note: Two runs of 04 Sqmm cable with 01 run of 04Sqmm earth wire along with casing caping shall be measured as one RM).

M&L for sub main wiring with four single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and two copper cable 6 sqmm continuous earth wire complete all as specified and as directed. . (Note: Four runs of 6 Sqmm cable with 02 run of 6 Sqmm earth wire along with casing caping shall be measured as one RM).

Taking down carefully existing unserviceable aluminium point wiring (light, fan, sockets or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials from site and making good disturbed surfaces of walls, floors, ceilings complete all as specified and as directed.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated and unsheathed, FRLS cable 1100 volt grade ISI -694 marked, drawn through in and including heavy duty, PVC casing/caping double lock type not less than 19mm of white /ivory colour including all accessories surface type, heavy duty ISI marked, with mild steel sunken boxes 1.6mm thick,60mm deep with earth dolly, covered with cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.50 sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and as directed for one light/fan point controlled by one, one way switch 5 Amp, 240 Volts complete all as specified and as directed.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated and unsheathed, FRLS cable 1100 volt grade ISI -694 marked, drawn through in and including heavy duty, PVC casing/caping double lock type not less than 19mm of white /ivory colour including all accessories surface type, heavy duty ISI marked, with mild steel sunken boxes 1.6mm thick,60mm deep with earth dolly, covered with cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.50 sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed for one 3/5 pin socket out let 5Amps, 240 Volts on the same board with other switches .

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated and unsheathed, FRLS cable 1100 volt grade ISI -694 marked, drawn through in and including heavy duty, PVC casing/caping double lock type not less than 19mm of white /ivory colour including all accessories surface type, heavy duty ISI marked, with mild steel sunken boxes 1.6mm thick,60mm deep with earth dolly, covered with cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.50 sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed for one 3/5 pin socket out let 5Amps, 240 Volts on independent board .

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated and unsheathed, FRLS cable 1100 volt grade ISI -694 marked, drawn through in and including heavy duty, PVC casing/caping double lock type not less than 19mm of white /ivory colour including all accessories surface type, heavy duty ISI marked, with mild steel sunken boxes 1.6mm thick,60mm deep with earth dolly, covered with cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.50 sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed one bell point controlled by one bell switch 5 Amps, 240 Volts.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 4 sqmm (nominal area), two single core, PVC insulated and unsheathed, FRLS cable 1100 volt grade ISI -694 marked, drawn through in and including heavy duty, PVC casing/caping double lock type not less than 19mm of white /ivory colour including all accessories surface type, heavy duty ISI marked, with mild steel sunken boxes 1.6mm thick,60mm deep with earth dolly, covered with cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 4 sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed for one 3 pin socket out let 15Amps on independent board .

S&F ceiling rose surface backalite three terminal, 50 mm dia PVC/polycorbonate insulated body including PVC mounting block white/ ivory /urea finish complete all as specified and as directed.

S&F switch piano flush type polycorbonate 5 Amps single pole one way, 230 volts complete all as specified and as directed.

S&F socket outlet polycorbonate 5 Amps, 2 in 1 , 3 pin 5Amps flush type complete all as specified and as directed.

S&F switch socket combination, 2 in 1, 5 and 15 Amps multipurpose flush type complete all as specified and as direcrted

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc 120 W, step type, suitable for operation on 230Volts 50Hz AC supply complete all as specified and as directed.

S&F switch bell push 5 Amps flush type, one way, 230 volts complete all as specified and as directed.

S&F Bell, ding dong type suitable for AC 230 volts,50 Hz, single pole complete all as specified and as directed.

S & F lamp holder, PVC/Polycorbonate type with back plate suitable for batten/angular fittings with and including one LED lamp 20 watt pin type complete all as specified and as directed.

S&F switch modular type 6 Amps one way, one module 230 volts white /ivory finish complete all as specified and as directed.

S&F socket outlet modular type 6 Amps, 2/3 pin combined two modules suitable for 3 pin/2 pin 5 Amp plug tops, complete all as specified and as directed.

S&F switch socket combination modular type 6A/16A , 2-3 Pin combined two modules suitable for 3 pin 6 Amp/16Amp plug tops, complete all as specified and as directed.

S&F switch modular bell push 6 Amps one way, one module 230 volts white /ivory finish complete all as specified and as directed.

S&F modular type fan regulator 120 W, 2 module, step type,suitable for operation on 230Volts 50Hz AC supply complete all as specified and as directed.

S&F sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete all as specified and as directed.

Supply of LED tube 1100 - 1200 mm in length along with CRCA LED Batten complete LED light fitting fixture including LED Tube and Batten, LED Tube fitting consist of Polycarbonate housing with extruded aluminium heatsink for mounting LED chip, LED tube system wattage consist of 18/ 20 w, 140 V - 260V AC, system Lumen Output min 1800 Lumen in 18 w or min 2000 lumen in 20 w with 5700 - 6500 K CCT with pf > 0.95 CRI > = 80 and with < = 10% THD with min 2.5 KV Surge protection in Built. LED Baten consist of power coated CRCA box type batten with decorative end caps should be supplied for installing above LED tubes complete all as specified and as directed.

S&F 1x10 watt, 230 V surface and wall mounted LED batten (for mirror) including extruded channel and decorative end caps with high efficiency electronic driver. High translucent PMMA diffuser is used get free smooth light distribution, with surge protection etc connecting up with twin core twisted flexible copper cable from ceiling rose to fitting complete all as specified and as directed. of make Crompton Greaves Cat No Linnet Cat No LCL-14-CDL or equivalent in makes listed in Appx 'C'

S & F Decorative wall mounting light fixture made with polycarbonate body suitable for 9/10W retrofit LED Lamp (B-22 base) including 01x9/10 W LED and connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified and as directed of make Havells Cat No City1 or equivalent in makes listed in Appx 'C'.

S&F 1x10 watt,230V surface mounted LED downlight with white powder coated polycarbonate housing and pressure die-cast heat sink having high efficiency, including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified and as directed of make Havells Cat part No LHEAABP7IL1W012 or equivalent in makes listed in Appx 'C'.

Taking down the exhaust fan carefully and cleaning/Servicing the fan if any repairs/replacing of parts required complete including painting the fan with enamel spray paint Grey colored and fixing back the fan with fixing accessoires required at site, and connecting the fan with and including new three core copper conductor flexible cord of 0.5 Sqmm cross sectional area complete all as specified and as directed.

S & F ceiling fan 5 star rated (after assembling the same) with the fan hook/box, 1200 mm (48") sweep, 240 Volts, 5 Star BEE rating milk white coloured and connecting up complete with regulator and including three core copper conductor flexible cord of 0.5 Sqmm cross sectional area, of required length from ceiling rose to connector block of the fan, fixing with required length of down rod and hook accessories complete all as specified and as directed.

S & F for plastic body exhaust fan, AC single phase, 240 V of not less than 3 star BEE star rating , size 250 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete and making good the disturbed surfaces and fixing to the wall with proper fastener arrangements and all accessories complete all as specified and as directed. Make -BAJAJ Cat Part No - 70049 MAXIMA DX BLACK" or equivalent in makes listed in Appx 'C'.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with 5700 - 6500 K CCT with pf > 0.95, CRI >=80 and with < = 10% THD, with min 2.5 KV Surge protection in Built and complete LED fixture with BIS R mark and R Registration no. with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including 25mm dia GI pipe medium grade bracket 1.5 mtr long bend to required shape and including taking down old unserviceable existing light fitting of any description complete all as specified and as directed.

S&F MCB DB 12 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 100 amp rated busbar, neutral & earthing link bar, surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as required at site complete all as specified and as directed.

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and as directed.

S&F MCB DP 40 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and as directed.

Supply and fix C Curve MCB DP 6 - 32 Amps working on 240 volts, 50 HZ,10 KA complete all as specified and as directed.

Supply and fix C Curve MCB TPN 40Amps working on 240 volts, 50 HZ,10 KA complete all as specified and as directed.

Supply and fix C Curve MCB TPN 32Amps working on 240 volts, 50 HZ,10 KA complete all as specified and as directed.

S&F IP-54, IK 09, protection metal double door Vertical TPN -DB rated busbar, 415 volts, 50 HZ complete with interconnection links, blanking plates, cable ties, identification labels TPN 8 way, 24 modules suitable for accommodating 200 Amps MCCB 4 pole as incomer and SP/TP MCB as out going and concealed in wall including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing Make - Legrand cat no-5077 52 or equivalent in makes listed in Appx 'C'complete all as specified and as directed. Note- MCCB 100 Amps 4 pole 25 KA with electronic protection unit as incomer will be measured seprately in relevant item.

S & F MCCB 100 Amps, 25 KA, 4 Pole,415V, electronic protection unit. MCCB should be with suitable spreaders and phase barriers for each terminals. MAKE: Legrand cat no- 420315 or equivalent in makes listed in Appx 'C' complete all as specified and as directed.

S&F MCB DB 04 way SPN Single door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 100 amp rated busbar, neutral & earthing link bar, surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete as required at site complete all as specified and as directed.

S & F stationary type electric water heater closed/vented type , inner body made out of copper with pressure rating not less than 60 N/Sq.cm of capacity 25 Liters suitable for 230 volts , single phase AC 50 HZ Supply ISI marked to IS;2082 (Part /1993) (reffirmed 2004) with latest amendments and having BEE Star (5 Star Rating of latest series) complete with all accessories and fittings as per requirement complete all as specified and as directed.

S&F electrical meter box compartmentalized design suitable for one energy meter and one 12 way DB, outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet for outer section and 1.6mm for doors and inner partitions, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakellite sheet for mounting the energy meter and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box shall not be less than 600 x 600 x 300 mm complete with all accessories prewired twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F electrical meter box compartmentalized design suitable for 1 energy meter and one 4 way SPN DB, outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet for outer section and 1.6mm for doors and inner partitions, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakellite sheet for mounting the energy meters and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box shall not be less than 600 x 600 x 300 mm complete with all accessories prewired twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F electrical meter box compartmentalized design suitable for 4 energy meter and four 4 way SPN DB, outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet for outer section and 1.6mm for doors and inner partitions, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakellite sheet for mounting the energy meters and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box shall not be less than 1200 x 1200 x 300 mm complete with all accessories prewired twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

M& L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including Galvanised steel earth wire 4mm dia as earthing lead, by means of bolts, nuts & checknuts and washers etc; including GI pipe 15mm dia medium grade pipe for protection of G.I earth strip, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to earth test point, GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including concrete pit in PCC (1:3:6) type C-1 , RCC 1: 2 : 4 type B-1 earth pit with cover slab of size 450x450x50mm reinforced with 8mm TMT @ 100 centre to centre both ways including one handle for lifting made of 8mm dia MS bar, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion complete all as specified and as directed.

nhsaluji and associates

V M MATERE INFRASTRUCTURES INDIA PVT LTD