SPECIAL REPAIR TO BLDG NO T-20 ARJUN LINES IN RA AT CAD PULGAON

Amount

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa and AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of single layer Mangalore pattern or similar tiles complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based crumpled corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa and AZ-150 as in ridge fixed with self tapping screws including dismantling of single layer Mangalore pattern or similar tiles complete all as specified and as directed.

Dismantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section unframed works complete all as specified and as directed.

M L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates grade of steel Fe-290(Gde E 165)

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directe incuding necessary formwork required complete all as specified and as directed.

M&L for PCC(1:2:4) type B-2 (using 20mm graded stone aggregate) as in surface channel in drains including demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for as in coping, drains complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brickwork (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finishwithout any extra cost to Govt) complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm & n exc 4 sqm each including cutting holes for taking out hold fast or dismantling brickwork (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finishwithout any extra cost to Govt) complete all as specified and as directed.

S&F for second class hard wood plain, solid, straight, chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned complete all as specified and as directed.

S&F Structural Steel work conforming to Fe-290 Gde E-165 as in framed structure for staging of water tank ,doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, incl 1 mm thick mild steel, plain sheet , cut to size,drilled, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, sliding bolts and fixing complete all as specified and as directed.

S&F factory made 35mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F factory made 2nd Class Hardwood 35 mm thick glazed and skeleton shutters open rebated & prepared to receive glass, gauge etc without sash bars edges & mitred beads for securing glass/gauge etc complete all as specified and as directed.

Supply & Fixing 30 mm thick factory made glazed skeleton shutter of 2nd class HW, open rebated and prepared to receive glass/gauze, divided into squares with plain chamfered mitred and rebated sash bar as in window/ventilator, sizes of members of shutters as specified in SSR Pt-I, section 8, clause 8.24(b) supplied and fitted to chowkats complete all as specified and as directed.

Cutting holes in stone walls built in cement mortar or cement lime mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 complete, depth of embedded portion of hold fasts not exc half brick complete all as specified and as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified & directed.

S&F of 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F of Stainless steel wire cloth, 0.36mm normal dia of wire and avg. width of aperture 1.40 mm and fixed with stinless steel wire staples complete all as specified and directed.

All as above but in repairs

S&F 100 mm long cold rolled, mild steel butt hinges medium weight complete all as specified and directed.

S&F 150 mm aluminium anodised, barrel tower bolts of extruded section all as specified and as directed

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, in opening complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm butt hinges, aluminium anodised of extruded section complete all as specified and as directed

S&F 100 mm aluminium anodised, barrel tower bolts of extruded section all as specified and as directed

S&F 100mm extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed

M&L for preparation of new wood or wood based surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old wood or wood based surfaces and applying a coat of synthetic enamel paint complete all as specified and as directed.

M&L preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide complete all as specified and directed.

S & F machine cut cudappah stone slab 20-25mm thick polished one side for kitchen platform over cement screed base 15mm thick in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl incl rubbing and polishing and demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded complete all as specified and as directed.

M&L for granite (of any type) work (table rubbed and polished) of 14-16 mm th as in steps, jambs, pillars, window-cills, cooking platforms and like laid over cement screed of 10mm th in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of existing stone slab and tiles of any description or th in floors , aprons etc

M&L for Brick work with fly ash bricks straight or curved on plan exc 6m in radius but built in 1:6 cement mortar including demoltion of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 including dismantling of existing floor tiling with cement mortar bedding (but not backing) and removing the rubbish off the premishes complete all as specified and as directed.

M&L for glazed ceramic tiles coloured of size 350x250x7mm/ 450x350x7mm thick fixed in vertical surfaces, set and jointed in neat cement slurry and pointed in white and colour cement to match incl 10mm thick screed bed in CM 1:4 including dismantling of existing wall tiling with cement mortar bedding (but not backing) and removing the rubbish off the premishes complete all as specified and as directed.

M&L for coloured non skid cermic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 including dismantling of existing floor tiling with cement mortar bedding (but not backing) and removing the rubbish off the premishes complete all as specified and as directed.

All as above here in before but on vertical surface as skirting over and incl 10 mm thick rendering in CM 1:3 including dismantling of existing skirting with cement mortar bedding (but not backing) and removing the rubbish off the premishes complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L 8-9mm thick designer ceiling board in ceiling fixed with screw as per manufactures instructions, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33mm thick galvanized steel sheet & of size T 24x32mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 4mm dia fixed pipe or wall plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runners at 600mm c/c to form 600x600mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19x19mm of white colour all as per instruction complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in flooring finished even and smooth without using extra cement including demoltion of existing damaged PCC and disposal of rubbish complete all as specified and as directed.

M&L for 75mm PCC 1:3:6 type C2 (using 20mm graded stone aggregate) as in plinth protection even and smooth without using extra cement including demoltion of existing damaged PCC and disposal of rubbish complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B2 (using 20mm graded stone aggregate) as in path/paving/hard standing and finishing the surfaces even and smooth without using extra cement including demoltion of existing damaged PCC and disposal of rubbish complete all as specified and as directed.

Taking down cement plaster of any description on brick/ Stone Walls or from Concrete Surfaces incl raking out joints, hacking for key, scrubbing down with water etc all as specified and removing unserviceable material outside premises complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6 on faces of brick work, stone masonry or concrete surfaces (internal) finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for 15mm thick rendering in two coats on stone/ brick/ concrete surfaces (external) finished even and smooth without using extra cement etc. 1st coat 10 mm thick in CM 1:6 and 2nd coat 5mm thick in CM 1:4 mix with water proofing compound as per manufacturer instructions complete all as specified and as directed. Note : WPC shall measured and paid Seprately

Supply only Integral water proofing Compound

M&L preparation of new or old plastered/unplastered surfaces of wall and applying two coats of oil bound distemper over coat of wall care putty on new plastered surfaces of wall complete all as specified and as directed.

M&L for preparation of new or old plastered/unplastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and as directed.

M&L for preparation of old plastered/unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

S&F 15mm bore medium grade glavanised tubes with all fittings and fixed complete to walls etc including taking up or down 15mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing complete all as specified and as directed.

S&F 20mm bore medium grade glavanised tubes with all fittings and fixed complete to walls etc including taking up or down 20mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing complete all as specified and as directed.

M&L for cutting chases for concealed pipe where required and pointing in cement mortar 1:3 etc, in stone, concrete block or slab walls complete all as specified and as directed.

S&F in repairs rotational moulded polyethylene water storage tank tripple layered (cylindrical vertical with closed top) hoisted and fixed in position of 500 litres capacity confiring to IS specification, incl 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs for vitreous china wash basin white flat back, size 580x450mm incl brackets, cutting for and pinning in ends of brackets or erecting stand, incl 32mm waste coupling of PTMT (half or full threaded) and waste pipe complete all as specified and as directed.

S&F in repairs stainless steel sinks with drainage board made of 1mm thick for kitchen with plugs washer, waste pipes, cast iron cantilever brackets, connecting union to pipe of overall size 915mm x 460mm, bowl size 410 x 330 x 160 mm with glossy finish, including bedding in cement mortar to dwarf wall fixing cantilever brackets and connecting unions to pipe incl 40mm waste coupling of PTMT (half or full threaded) and waste pipe complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, 630 x 450 mm with integral foot rests (excluding flushing cistern and flush pipe) with connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor including trap set in and including concrete complete all as specified and as directed.

S&F in repairs PVC valveless, syphonic action type, 10 ltrs capacity flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and as directed.

S&F in repairs Steel plate rack made of stainless steel fixed with plugs, washers and steel screws including bedding in cement mortar on to dwarf wall, overall size 600mm x 750mm, complete all as specified and as directed.

S&F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and as directed.

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and as directed.

S&F in repair PVC (SWR) bends any radius of 75mm bore complete all as specified and as directed.

Ditto but of 110mm bore complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F in repairs CP soap dish approximate size 160x160x90mm complete all as specified and as directed.

S&F in repairs 15 mm bore dia of Pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, scewed for union pipe and fixed to 15mm dia pipe complete all as specified and as directed.

S&F in repairs 15mm bore dia of stop valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs 15mm bore dia of angle valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs 15mm bore dia Bib tap chromium plated with crunch or butterfly handle , screwed for iron pipe or for brass pipe and fixed complete all as specified and as directed.

S&F in repairs 20mm bore gun metal gate valves, with iron wheel head , screwed both ends for iron pipes complete complete all as specified and as directed.

S&F in repairs chromium plated shower rose 125mm size complete all as specified and as directed.

S&F in repairs tubular towel rail aluminium anodised, 20mm dia, D type 60 cm long between flanges complete all as specified and as directed.

S&F in repairs CP grating 110mm.

Taking down carefully concealed/casing capping point wiring copper/aluminium(light/fan/socket) complete (with fittings such as switches ceiling rose, pendents, regulators,sockets etc) and making good disturbed surface with existing specification all as specified and directed by Engineer-in-Charge.

Material and labour for point wiring complete with 1.5 sqmm single core sheathed PVC insulated FRLSH cable 1100 V grade multistranded copper conductor of code red, blue and yellow for phase, black for neutral and green for earth of ISI marked drawn through and including PVC casing caping of suitable size with accessories ISI marked on wall/ceiling including PVC insulated copper cable FRLS 1100 V grade multi stranded for earth continuity conductor of same type and size and connected to earth dolly including provision of PVC boxes of suitable size PVC boxes for mounting switches/sockets and regulators complete all as specified and as directed.

One light point controlled by one switch one way

One ceiling fan point controlled by one switch one way

All as per item above but one bell/buzzer point controlled by one push button on the same board with other swiches or independent with 1.5 sqmm size.

All as per item above But for One socket outlet three pin 5/6 Amps controlled by one switch on the same board.

All as per item above But for one switch socket outlet three pin 5 /6 Amps controlled by one switch on independent board.

All as per item above But for one switch socket outlet three pin 15 Amps, independent with 4sqmm .

M&L switch piano flush type single pole,one way, 5 Amps, 240 V complete all as specified and directed

S&F socket outlet 5/6 pin type,5 Amps, 240 V complete all as specified and directed

S&F socket outlet (Multipurpose type) but 5A/15A flush type complete all as specified and as directed.

S&F switch flush type 15/16A complete all as specified and as directed.

S&F in replacement lamp holder,PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed

S and F call bell electrical operated complete all as specified and as directed

S&F fan regulator electronic step type AC 240 Volts,50 Hz complete as specified and directed.

S and F bell switch piano flush type complete all as specified and directed.

S&F ceiling rose surface type with 3 terminals complete .Make : Havells/SSK/Cona

M&L sub main wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in PVC Casing caping of 2 run of 4sqmm PVC FRLS copper cable and 1run of 4sqmm PVC FRLS copper cable for earth wire complete all as specified and directed. Note for sub main wiring :- (i) 2 runs of wire and 1 run of earth wire will be measured as one unit i.e RM (ii) Groove Cutting ,pinning and plastering of disturbed surface etc shall deemed to be included in the quoted rate.wiring 2 run of wire and1 run of earth wire

Supply and Fix to wall /pole of any heights in replacement of LED bldg security lights 35 watt IP-65 including GI Pipe suitable size bracket not less than 1 mtr to bend to shape with two clamps, nuts, bolts, washers and PVC 3 core ISI marked flexible wire from ceiling rose to fitting complete including taking down unserviceable lights complete all as specified and as directed.

S&F in replacement LED tube light fittings 1 x 18/20 watt including suitable size of batten complete (01 set) single/double side connection) including taking down old unserviceable any type of tube light fittings complete all as specified and as directed.

S&F in replacement of sheet steel enclosure with double door flush mounting ,MCB, DB, SPN, 4 ways,240 volt factory fitted rated bus bars,earth bar,neutral links complete incl. blanking plates as required & making good the disturbed surfaces complete all as specified and directed.

S&F in replacement of MCB SPN 32 Amps 240V ,50 Hz ,breaking capacity 10 KA," C " series complete all as specified and directed.

S&F in replacement of MCB SP 06-32 Amps 240V ,50 Hz, breaking capacity 10 KA," C " series complete all as specified and directed.

Supply, laying and testing in replacement of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core complete all as specified and directed.

S and F in repairs of sheet steel enclosure with Double door TPN 4 ways 440 volt factory fitted rated bus bars,earth bar,neutral links complete including blanking plates as required and making good the disturbed surfaces all as specified and as directed.

S and F in replacement of MCB TPN 63 Amps 415V ,50 Hz ,breaking capacity 10 KA," C " series all as directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5M depth for laying of cables,GI/CI pipe lines etc getting out including forming bottom surface to required level and gradient in hard/dense soil.complete all as specified and directed.

M&L for Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard/dense soil. complete all as specified and directed.

Removing excavated material/soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed.

Material and labour for sand cushioning with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed. Note : Punned thickness only shall be measured and paid.

Supply and lay un-reinforcement precast concrete cable cover, class LV, type 2, flat of size 300 X 180 X 40mm for LT cable and laid dry in trenches over underground cables complete all as specified and directed

Taking down carefully submain wiring including batten/conduit by unscrewing from wall, ceiling and making good surfaces to match with original status as specified and directed

Material and labour earthing complete with galvanised earth plate electrode 60cmx60cmx6mm thick buried directly in ground not less than 2.25mtr deep below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to galvanised earth lead 4 mm dia by means of bolts, nut check nuts and washers of galvanised iron or steel, earth lead protection pipe 15mm bore GI medium grade, watering pipe 20mm bore GI medium grade all as shown in electrical plate No 3 connected to main switch distribution board complete and testing on completion all as specified and directed by Engr-in-Charge. Note : (i) The unit rate shall also includes for excavation earth work, type of soil, pit in PCC 1:3:6 type C1 funnel with watering pipe from earth test point upto equipment to be earthed, RCc 1:2:4 type B1 cover for earth chamber, 50mm thick with 8mm dia for steel 150mm C/C both ways and 6mm dia MS round bars at handles of cover slab all as specified in addition to sl No 1 (a) to (e) and 3 of under sub heading earthing as specified on ser page No 441 of SSR Part-II-2010. (ii) The rate shall be deemed to include for taking out existing earthing complete.

Supply and fixing LED polymer bulk head with opaque polymer diffuser for optimum light with 10 LED bulb as per IP-65 protection including light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan steel body AC single phase 230 Volts of size 380mm sweep with blades and frame and louvers complete all as specified and directed.

M/S L M Chourasia

SHREE CONSTRUCTIONS

M/S Ramakant Chourasia

M/s Dara Constructions, Pulgaon

SHRI RANI SATI TRADERS

M/s Prakash Agencies

Bidder Name

M/S L M Chourasia

SHRI RANI SATI TRADERS

SHREE CONSTRUCTIONS

M/S Ramakant Chourasia

M/s Dara Constructions, Pulgaon

M/s Prakash Agencies

Krishana electronics