SPECIAL REPAIR OF NURSING OFFR MESS BLDG NO P-11 (INCULDING ANCILLARIES BLDG NO P-11B,P-110B, P-11G AND P-11J) OF MH JAIPUR UNDER ZONE II AREA AT JAIPUR MIL STN

Amount

M&L applied a coat of bituminous primer confirming to [email protected] Kg per Sqm and providing APP BASED POLYMERIC Membrane not less than 3 mm thick. Weighing not less than 3 Kg/m2, reinforced with polyester non woven fabric(weighing not less than 150 Gm/Sqm) shall be laid dry torch application, side overlaps shall be 75 mm and end slab shall be 100 mm and all over laps and joints shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing all as directed and screed bed or bedding layer or mortar 15mm thick in cement mortar 1:4 with WPC on roof surfaces including taking down cement plaster on roof surfaces, cleaning and removing rubbish including roof treatment etc. complete all as specified and directed.

M & L for cutting out cracks to V-section in existing roofs or terracing cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight), etc complete all as per specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiling to store and rubbish off the premises etc complete all as specified and directed.

M&L vitrified ceramic coloured tile of 10 mm thick square/rectangular polished area of each tile not exceeding 0.36 sqm in floor etc set and jointed in neat coloured cement to match the shade over and including providing 15 mm thick screed bed in CM (1:6) etc complete all as specified and as directed.

M&L vitrified ceramic coloured tile of 10 mm thick square/rectangular polished area of each tile not exceeding 0.36 sqm on vertical surfaces in skirting of size 600mmx100mm etc set over etc set and jointed in neat coloured cement to match the shade over and including providing 10 mm thick plaster in CM (1:4) etc complete all as specified and as directed.

M&L non skid ceramic tiles (white) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 15mm thick screed bed in CM (1:6) etc .complete all as specified and directed.

S&F coloured glazed ceramic tiles first quality of size (450x300)mm, 7 to 8 mm thick , in skirting, dado and risers to step, wall etc set and jointed in neat cement slurry and pointed in coloured cement to match shade of tiles and including providing 10mm thick screed bed in CM (1:4) etc complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm thick laid over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified & as directed.

M&L machine cut kota stone slab flooring 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M&L of 20 to 25mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and rounding the edges and including providing 15 mm thick screed bed in CM (1:4) etc complete all as specified and directed.

M&L of Granite(of any type) tiles 20 mm thick machine cut ,bedded and jointed with grey cement and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including providing 15 mm thick screed bed in CM (1:6) and securing of granite stone over all with steel studs spacing not more than 1m complete on gate pillars/wall etc complete all as specified and directed.

M&L and repair Dholpur stone cladding 16-18mm thick gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm and not exceeding 0.50 sqm area fixed with making ‘V’ groove at top of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment including providing 15 mm thick screed bed in CM (1:6) and securing of granite stone over all with steel studs spacing not more than 1m complete on gate pillars/wall etc complete all as specified and directed.

S&F Dholpur stone old surface cladding polishing, rubbing & including silicon treatment etc complete all as specified and directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces/ceiling etc. including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on stone masonry surfaces or surface other than fair faces of brick work on wall CM (1:4) on walls finished even and fair without using extra cement etc complete all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces or surface other than fair faces of brick work on wall in CM (1:6) finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:3) on ceiling or RCC facia etc finished even and fair without using extra cement etc complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of oil bound distemper over a coat of wall care putty on wall over a coat of primer on wall etc. complete all as per specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of weather proof emulsion paint over a coat of wall care putty on wall over a coat of primer on wall etc. complete all as per specified and directed.

M&L complete removal of existing treatment on wall surfaces and applying two coats of oil emulsion distemper over a coat of alkali resistant primer and wall care putty etc complete all as specified and as directed.

M&L complete removal of existing treatment on wall surfaces and applying two coats of weather proof emulsion paint over a coat of primer and wall care putty etc complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store etc complete all as specified and as directed.

Taking down door shutters including chowkats (without taking of shutters) exceeding 1.5 sqm but not exceeding 4 sqm etc complete all as specified and as directed.

Taking down shutters of any description not exceeding 1.00 each. etc complete all as specified and directed.

Taking down shutters of any description exceeding 1 sqm and not exceeding 2.00 each. etc complete all as specified and directed.

S & F factory made uPVC white colour sliding window. area exceeding 2 sqm each, Three track made of extruded profile with wall thickness of 2.3mm (plus/minus 0.2mm) window profile with hollow section with multi chamber, frame (88mm x 52mm) sliding sash (42mm x 67 mm), sliding mesh sash (42mm x 57 mm), sliding interlock (one vertical length in each shutters) (45.5mm x 28mm), glazing beads(24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of water etc, making arrangement for fixing and providing and including of hardware, EPDM gasket, 1.2mm plus/minus 0.2mm thick galvanized steel frame (30mm x 18mm ) 2Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners etc complete all as specified and as directed. Hardware: Touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. NOTE FOR ITEM NOS 26 TO 28:- The unit rate quoted by contractor inclusive cost of glass and all other connected accessories.Net opening will be measured for payment purpose.

S&F in repair 5 mm thickness plain glass packing with rubber gasket, aluminium beading etc around both side for fixing the glass etc complete all as specified and directed.

S&F 12mm thick medium density fibre (MDF) board exterior grade, both side choice lamination of approved colour fixed in doors/partitions etc complete all as specified & directed.

S&F in repair of 5 mm thickness toughened glass and glazing with oil putty in square each pane etc complete all as specified and directed.

S&F Mortice lock, vertical type, size 100mm brass 4 levers etc complete all as specified and directed.

S&F in repair for hydraulic operated double action floor spring for aluminium door made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed etc complete all as specified and directed.

S&F in repair aluminium (Diecast) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutters of 851mm to 1000mm in width and weight between 61 to 80 kg etc complete all as specified and directed.

S&F in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified SSR 2010 (Part-II) and Particular specification.etc complete all as specified and directed.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixing in opening complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 100mm length of bolt etc complete all as specified and directed.

S&F 100mm long extruded aluminium handle cast type anodised etc complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 etc complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L for brick work sub class B bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:4) etc complete all as specified and directed.

M&L reinforced cement concrete M-25 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified & directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) Rough finished surface of concrete flat. etc complete all as specified & directed.

M&L TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as per specified and directed.

M&L TMT bars 6mm to 8mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as per specified and directed.

M&L TMT bars mild steel bars 5mm dia and over upto and including 10mm dia cut to length bent to shape required including cracking, bending in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified & directed.

S&F for 15 mm GI tubing medium grade with all fitting and fixed to walls of concealed or fitted to ceiling or laid in under floor including taking out old unserviceable GI tubing etc complete all as specified & directed.

S&F for 20 mm GI tubing medium grade with all fitting and fixed to walls of concealed or fitted to ceiling or laid in under floor including taking out old unserviceable GI tubing etc complete all as specified & directed.

S&F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore dia pipe etc complete all as specified & directed.

S&F in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type). of pipe in 15mm. etc complete all as specified & directed. Make: Cera New Cat No F2002361 or equivalent as mentioned in Appx ‘B’

S&F in repairs to 15mm dia bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified & directed. Make: Cera New Cat No F2002151 or equivalent as mentioned in Appx ‘B’

S&F PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified & directed.

S&F in repair aluminium anodised tubular towel rail 20 mm dia ,D type,60 cm long between flanges with bracket etc complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and guard railing 60cm long etc complete all as specified and directed.

S&F in repair ball brass valves, high pressure, with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule and fixed of pipe in 20mm.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe etc complete all as specified & directed.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm etc complete all as specified & directed.

S&F in repair PVC valve less syphonic action type flushing cistern 10 litres capacity, low level white with inlet ball valve float and handle including brackets etc complete all as specified & directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) etc complete all as specified & directed.

S&F plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified & directed.

S&F in repair grating doom 100 mm dia of PTMT(Minimum weight 25gms) etc complete all as specified & directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT.(Minimum weight 40gms) etc complete all as specified & directed.

S&F in repair Vitreous China wash basin, snow white, Canton pattern, size (615x510)mm with pedestal including 32mm dia CP waste coupling and 25mm dia and 75cm long PVC waste pipe with 32mm dia connector etc complete all as specified & directed. Make: Wash basin of make Cera Canton New Cat No S2040122 or equivalent as mentioned in Appx ‘B’ Make: Pedestal of make Cera New Cat No S2090107 or equivalent as mentioned in Appx ‘B’

S&F in repair Vitreous China one piece EWC with soft close seat cover and twin flush fittings snow white in colour of size 690mm x 380mm x 780mm etc complete all as specified & directed. Make: Cera Cloud S trap New Cat Nos S1013123 or equivalent as mentioned in Appx ‘B’

S&F in repair toilet paper holder with flap guard etc complete all as specified & directed. Make CERA New Cat Part No F5007110 or equivalent as mentioned in Appx ‘B’

S&F in repair fancy type Health faucet 15mm bore (ISI marked) including extension pipe of 1 mtr long etc complete all as specified & directed. Make CERA New Cat Part No F8030301 or equivalent as mentioned in Appx ‘B’

S&F in repair CP Jet suitable for EWC with 01 mtr pipe (ISI marked) etc complete all as specified and directed.

S&F in repair central hole single lever wash basin mixer 15mm dia with 450 mm braided connection pipe etc complete all as specified & directed. Make: CERA New Cat Part No F2007461 or equivalent as mentioned in Appx ‘B’

S&F in repair CP brass towel ring etc complete all as specified & directed. Make: CERA New Cat Part No F5004105 or equivalent as mentioned in Appx ‘B’

S&F in repair wall mixer 15mm dia (3 in 1) with arrangement for both telephonic shower and overhead shower and bend pipe etc complete all as specified & directed. Make: CERA New Cat Part No F2007403 or equivalent as mentioned in Appx ‘B’

S&F in repair soap dish chromium plated etc complete all as specified & directed. Make: CERA New Cat Part No F5007106 or equivalent as mentioned in Appx ‘B’

S&F in repair Oceana corner glass shelf (large) 300mmx300mm etc complete all as specified & directed. Make: CERA New Cat Part No F5005103 or equivalent as mentioned in Appx ‘B’

S&F in repairs to 15mm dia bib taps two way fancy type, chromium plated cast copper alloy with capston head, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified & directed. Make: CERA New Cat Part No F2008163 or equivalent as mentioned in Appx ‘B’

S&F in repair angle cock, cast copper alloy, screwed down, high pressure, with capstan head, screwed both ends for iron pipe or for unions of pipe in 15mm. etc complete all as specified & directed. Make: CERA New Cat Part No F2002201 or equivalent as mentioned in Appx ‘B’

S&F magazine tumbler holder brass chromium plated etc complete all as specified & directed. Make: CERA New Cat Part No F5004107 or equivalent as mentioned in Appx ‘B’

S&F capacity of 500 Litres rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old water tanks etc complete all as specified & directed.

S&F capacity of 1000 Litres rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old water tanks etc complete all as specified & directed.

M&L in repair PVC(SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement dia of outlet 75 mm etc complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends (any radius) provided with access door etc complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bends (any radius) provided with access door etc complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl etc complete all as specified and directed.

Excavation in post holes each not exceeding 0.5 Cum getting out, in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface all as specified and directed.

M&L cement concrete in foundations, filling and mass concrete type D2, (1:4:8) using 40 mm graded aggregate. etc complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc confirming to Fe-410W (Gde E-250) Quality-`A' etc complete all as specified and directed.

Providing and fixing in repair false ceiling with 12.50 mm thick plain gypsum board :6 Providing, fixing and finishing two level false ceiling ( Tentative levels of the first and second level of finished false ceiling soffits may be 300 mm and below the roof slab) using 12.50 mm thick plan gypsum boards of fabricated and fixed to the soffit of roof/ beams and wall of frame work made of special sections. Power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6mm thick with flangers of 27 mm and 37mm at 1200m centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate GI channels 45x15xx0.9mm running at the spacing of 1200mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clip of 10.5mm, at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230 mm long G.I. wire at every junction including perimeter channels 0.5 mm thick 27mm high having flanges of 20mm and 30 mm long the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 X 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and applying plaster of paris putty for required thickness. The surface of the false ceiling fixed as above shall be prepared by sand papering, providing, applying and finishing a coat of approved make white cement putty, two coat of approved make cement primer and two or more coats of approved make and shade premium plastic emulsion, etc. Exposed clear (flat) measurements only shall be considered for payment, all as per manufacture’s specification and also including the cost of making openings for light fittings, frills, diffusers cutouts made with frame of perimeter channels suitably”

S&F pre painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/rain gutter (EVA) to wall, fixed with self tapping screws and washers etc complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

De-sludging and cleaning of existing manholes (excluding first manhole) of any size and shape exceeding 1 mtr and not exceeding 2 mtr deep by removing all sludge, waste, debries etc from manholes and cleaning with water including disposing of all sludge, waste, debries etc outside MD land etc complete all as specified and as directed.

Cleaning of soak well 2.4 mtr dia and 4.5 mtr depth (overall depth) using mechanical pumps diesel driven with fuel, operator and necessary excavation on half buried soil and disposed off soak well water etc in pits including necessary excavations and earth work for pits etc in soft/loose soil etc complete all as specified and as directed.

Disconnecting old unserviceable soak well and M&L for construction of soak well (100 users) 2.40 metre internal dia and over all depth of 3.00 including necessary excavation and earth work in any type of soil PCC 1:4:8 type D-2 using 40mm graded stone aggregate and all RCC work (1:2:4) type B1 etc complete all as specified and shown on drg No CEJZ/2004/TD/S-35 sheet No 1/1 dated 11 May 2004 and revised dated 06 Aug 2005.

M&L cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1 using 20mm graded stone aggregate smooth finished, and reforming benching required for 150mm pipe etc complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry pointed. etc complete all as specified and as directed.

M&L 75 mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base of flooring etc complete all as specified and directed.

M&L Chequered cement concrete tiles 25 x 25 x 25mm thick set in cement mortar, including providing 15mm thick screed bed in CM (1:6) and jointed and pointed in neat cement slurry with grey cement and no pigments as in floors/ steps/ skirting etc complete all as directed by Engineer-in-charge.

M&L for machine pressed rubber moulded precast concrete interlocking paver block, 80mm thickness, M-40 grade of any shape and size confirming to IS-15658-2006, with grey cement and pigment laid over and including providing 25mm thick sand cushion and joints of interlocking tiles filled with dry sand and compacted with mechanical plate vibrator etc complete all as specified & directed.

M&L preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and as directed.

S&F sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on dwarf wall with fixing cantilever brackets and connecting union to pipe overall size 1120mm X 457mm bowl size 460mm X 330mm X 203mm including providing waste pipe of polyethylene of flow or high density or PVC 32mm dia and waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in cement mortar (1:3) or PCC (1:2:4) type B0 using 12.5 graded stone aggregate including taking down of existing old sink etc complete all as specified & as directed.

S&F in repair stainless steel kitchen plate rack of overall minimum size 900mm x 900mm x 225mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws all as directed of approved quality etc complete all as specified & directed.

S&F self closing hinge, stainless steel bright finish or electro galvanised for kitchen cupboards etc complete all as specified & directed.

S&F brass handle 100mm size fancy type polished bright finish etc complete all as specified & directed.

S&F multipurpose locks 02 levers for cabinet and movable box type drawer etc complete all as specified & directed.

Cutting holes 25 mm dia in kota stone for gas pipe etc complete all as specified & directed.

S&F 18mm thick medium density fibre MDF board both side white using in kitchen cabinet, drawer sets etc complete all as specified & directed.

S&F 18mm thick medium density fibre (MDF) board post from purpose made shutter laminated one side with 0.8mm thick choice lamination and other side white in cabinets, both side white using kitchen cabinets, drawer sets etc complete all as specified & directed.

S&F 19mm thick medium density fibre (MDF) board using for kitchen cabinets door shutters in wood grain colour, half round edge etc complete all as specified & directed.

S&F 19mm thick medium density fibre (MDF) board using in shelf and partition of kitchen cabinets etc complete all as specified & directed.

S&F telescopic channel 450mm long made for drawers etc complete all as specified & directed.

S&F plain stainless steel basket of size 43cmX50cmX15cm to fix in kitchen cabinets drawers made with 4 mm stainless steel wire as per standard trade practice etc complete all as specified & directed.

S&F plain stainless steel basket of size 43cmX50cmX10cm to fix in kitchen cabinets drawers made with 4 mm stainless steel wire for putting cutlery as per standard trade practice etc complete all as specified & directed.

S&F plain stainless steel basket of size 43cmX50cmX20cm to fix in kitchen cabinets drawers made with 4 mm stainless steel wire as per standard trade practice etc complete all as specified & directed.

S&F plain stainless steel basket of size 52cmX50cmX15cm to fix in kitchen cabinets drawers made with 4 mm stainless steel wire for putting plates as per standard trade practice etc complete all as specified & directed.

S&F plain stainless steel basket of size 435mmX510mm to fix in kitchen including tee and guide channel etc complete all as specified & directed.

Taking down existing aluminium door & window of any size and refixing in same and other opening after easing & changing necessary jointing cleats, glazing, clips, rubber packing anodised aluminium, snap beading and screws etc complete all as specified & directed.

M & L for repair to spalling of concrete by applying bond coat of SWR bonding agent & Cement in 1:1 ratio for bonding old and new concrete on damaged surfaces and applying polymer modified mortar in CM (1:3) having 20 mm avg thickness etc complete all as directed by Engineer-in-charge. Note :- (a) Supply only polymer mortar additive will be measured and paid separately. Repairs to be done by authorised applicator of make Dr Fixit or equivalent in Build core/Fosroc/Pedilite. (b) (i) Quantity of polymer shall be 15% by weight of cement. (ii) Pan mixer shall be used to get homogenous dough on bond coat surfaces. (iii) Required thickness shall be achieved by repeating this step after 24 Hrs to as required. (iv) Repaired surfaces area shall be kept moist for 5-7 days

S&F plain solid straight second class hardwood chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered put together with glue pinned at joints etc complete all as specified & directed.

Taking down carefully surface aluminium or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces etc complete all as specified & directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators as required for the following :- Note - Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall deemed to be included in quoted rate of point wiring). complete all as specified & directed.

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on independent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for one 16 amp socket outlet point controlled by one switch on independent board. (Note - Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall be deemed included in quoted rate of point wiring). etc complete all as specified & directed.

S&F angle holder, insulated polycarbonate body with back plate etc complete all as specified & directed.

S&F modular switch one way, SP, 6 amp, 1 module etc complete all as specified & directed. Make: Legrand mylinc cat ref No. 675501 or equivalent as mentioned in Appx’B’.

S&F modular switch one way, SP, 16 amp, 1 module etc complete all as specified & directed. Make: Legrand mylinc cat ref No. 675511 or equivalent as mentioned in Appx’B’.

S&F modular socket 6/16 -2/3 pin combined 2 module etc complete all as specified & directed. Make: Legrand Mylinc cat ref No. 675555 or equivalent as mentioned in Appx’B’.

S&F modular socket 6 amp 2/3 pin combined 2 module etc complete all as specified & directed. Make: Legrand Mylinc cat ref no. 675550 or equivalent as mentioned in Appx’B’.

S&F modular hum free electronic step fan regulator, 100 watts, 2 module etc complete all as specified & directed. Make: Legrand Mylinc cat ref no. 675530 or equivalent as mentioned in Appx’B’.

S&F ceiling rose 6 amp, 3 plates polycarbonate body etc complete all as specified & directed.

S&F exhaust fan size 300 mm sweep totally enclosed highly efficient heavy duty motor with pressure dia cast aluminium rotor mounted on two ball bearing. Rigid frame with rubber mounting for silent operation etc complete all as specified & directed.

M&L for submain wiring along with earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of following nominal sizes:-

(a) 2x4 sqmm + 1x4 sqmm earth wire in 20 mm dia conduit.

(b) 2x6 sqmm + 1x6 sqmm earth wire in 25 mm dia conduit.

S & F MCB distribution board powder coated , CRCA steel sheet, degree of protection IP 43-IK 09 with reversible double door, recess mounted having insulated 100 Amps tinned copper bus bar, neutral busbar, earth bar detachable gland plate interconnection earthing connection , blanking plates in unused spaces including connections of wires in MCBs/RCCBs/RCBOs/MCCBs with suitable size lugs of copper materials. DBs shall be fixed on wall in flush pattern by chase cutting in stone or brick wall and disturbed surfaces shall be made good even and smooth using CM (1:3) as required with following ratings & ways:-

(a) SPN, 240 volts, 4 ways Make: Legrand cat ref No 507610 or equivalent as mentioned in Appx’B’.

(b) SPN, 240 volts, 8 ways Make: Legrand cat ref No 507611 or equivalent as mentioned in Appx’B’.

(c) SPN, 240 volts, 12 ways Make: Legrand cat ref No 507612 or equivalent as mentioned in Appx’B’.

S&F MCB distribution board, VTPN type tripple pole and neutral, powder coated CRCA steel sheet suitable for MCCB incomer upto 160 amp, 4 way, 415 volts, degree of protection IP 43 - IK- 09 with reversible double door, recess mounted, having 250 amp insulated tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required of make Legrand cat ref No 507745 or equivalent as mentioned in Appx’B’ including providing MCCB four pole, 125 amps, 16 KA thermally adjustable between 70% to 100% with 4 spreader link set of same make and connections etc complete all as specified and directed. Make: Legrand cat ref No 420016 or equivalent as mentioned in Appx’B’.

S&F MCCB four pole, 100 Amps, 16 KA thermally adjustable between 70 to 100% including 4 spreader link set of same make as that of MCCB for connection, required lugs as required etc complete all as specified & directed. Make-Legrand cat ref No 420016 or equivalent as mentioned in Appx’B’.

Supply and laying or fixing on wall or passing through pipe testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 35 sqmm 3.5 core complete all as specified & directed.

Supply and laying or fixing on wall or passing through pipe testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 16 sqmm 2 core complete all as specified & directed.

Supply and laying or fixing on wall or passing through pipe testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 6 sqmm 2 core complete all as specified & directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc or for shaft, well, cesspit, manhole, pier holes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out soft/loose soil.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cm thick .etc complete all as specified & directed.

Removal of excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point .etc complete all as specified & directed.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete. Note :- Punned thickness shall be measured.

Supply and laying old size bricks, common burnt clay building bricks sub class ‘B’ designation 75 laid in trenches over sand for cable protection complete.

S&F steel tubes 40 mm bore light grade ISI marked with medium grade fittings for cable protection as required complete all as specified & directed.

S&F steel tubes 80 mm bore light grade ISI marked with medium grade fittings for cable protection as required complete all as specified & directed.

M&L for of bus bar chamber pedestal type of size 75cm x 60cmx40cm outdoor dust & vermin proof front opening made out of 2.0mm thick MS steel duly painted and consisting with aluminium bus bar 3 phase and neutral 4 Nos 400 Amp fixed on insulators and one MCCB TPN 200 Amp, 25 KA rupturing capacity including providing necessary in PCC 1:3:6 type C1 using 20mm graded stone aggregate including providing danger plate etc complete all as specified & directed.

M&L for pipe in chemical earthing with GI pipe electrode 3.0 m long having outer pipe dia 50mm & inner pipe dia 25 mm duly fitted with highly conductive and anti corrosive compound tested from NABL certified Laboratory of required quantity in ground by digging a bore of 100mm dia surrounded by soil friendly backfill compound including providing connection with galvanised earth wire 4 mm dia from earth electrode to the equipment to be earthed duly protected in 15mm medium grade GI pipe upto 7.5m, making PCC pit of size 0.3m x 0.3m x 0.3m (inner size) in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover with lifting hook made out of 8mm dia bar and testing on completion to achieve value not more than 2.0 ohm etc complete all as specified & directed.

S&F in repair LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumen per watt and total power consumption not more than 19 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 etc complete all as specified & directed. Make: Philips Cat Ref No. Endura Next Batten "BN 108C LED 20S PSU CDL WH" or equivalent as mentioned in Appx’B’

S&F in repairs LED batten 9 watt, 900 lumens operating voltage 160 to 360 volts, colour temperature 6500K including connection etc complete all as specified & directed. Make: Philips Astra Line 9 Watt LED Batten or equivalent as mentioned in Appx’B’.

S&F in repairs LED bulk head fitting 9 watt IP 66 & IK 09 with pressure die cast aluminium housing & polycarbonate diffuser duly pre wired connection with 0.75 Sq.mm PVC insulated & sheathed three core flexible multi stranded copper conductor cable etc complete all as specified & directed. Make: Philips Cat Ref No. WT 202W LED 6S CW PSU S2 PC or equivalent as mentioned in Appx’B’

S&F power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame etc complete all as specified & directed. Make: Legrand Mylinc Cat Part No 675558, 689009, 675564& 675584 or equivalent in Schneider/Havells/CG/ as approved.

S&F street light fittings green line high efficiency LED street light luminaries 20 watt complete with drive, pressure dia cast aluminium housing, UV stabilized polycarbonates cover, in built power unit, IP 65 protection including mounting bracket made of 25 mm GI pipe, medium grade ISI marked not less than 1.2 m bend in shape with two number clamps, nuts, bolts, washers as required etc complete all as specified & directed. Make: Philips cat ref No BRP042 LED 14 CW MR S1 PSU GR or equivalent as mentioned in Appx’B’

S&F post top lantern light fitting LED 15 watts, IP 65 protection including clamps, nuts, bolts, washers, fasteners and copper connecting cable as required etc complete all as specified & directed. Make: Havells cat ref No CORALMINIPT15WLED757PSYMTOPC or equivalent as mentioned in Appx’B’

S&F bollard LED garden light 08 watt (1.2M), IP 65 protection including clamps, nuts, bolts, washers, fasteners and copper connecting cable as required including providing PCC (1:2:4) type B1 using 20mm graded stone aggregate (Size 0.4MX0.3MX0.45M) etc complete all as specified & directed. Make: Havells cat ref No CONENXGBLS8WLED857PSYMTOPCM or equivalent as mentioned in Appx’B’

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

(a) Single pole 6 to 32 amps of Make Legrand cat ref Nos 408587 to 408595 or equivalent as mentioned in Appx’B’

(b) Double pole 10 to 32 amps of Make Legrand cat ref Nos 408631 to 408636 or equivalent as mentioned in Appx’B’

(c) Double pole, 40 to 63 amps of Make Legrand cat ref Nos 408637 to 408639 or equivalent as mentioned in Appx’B’

Taking down MCB distribution boards with incoming and outgoing controls etc complete all as specified & directed.

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good surface etc complete all as specified & directed.

Schedule of Credit

Narayan Enterprises

UNIVERSAL INFRAPROJECT PVT LTD

J.J.ENGINEERING

M/S Mohan Lal Gupta