REPAIR AND MAINTENANCE OF BED HARD, RACK AND OTHER FURNITURES FOR DIFFERENT MIL STN UNDER GE RANGIA

Amount

Note:-S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing nailing,wedging, glueing, providing hinges,applying putty to level the surface, placing every part in-tact and polishing the disturbed portion & Scratching the entire wooden pallets ,filling putty to the bore holes making surface smooth by scratching it with sand emery paper, the Wooden furniture shall be French polished with high gloss finish shade as approved by GE/BSO ,after properly cleaned and smoothened the surface.Painting the steel disturbed portion & painting steel surface with two coats of synthetic enamel paint of existing shade with spray gun & apply red oxide primer where ever required after properly smoothening the surface with sand paper Top shall be 18 mm thick exterior grade pre-laminated particle board one side laminated in light Wallnut shade or as approved by GE, duly fixed with half round 4 mm thick teak wood beading in matching shade with synthetic adhesive(Fevicol SH). Make of particle board : Century/Archid /Greenply.All kind of work will be executed where the furniture exist in different User Units of GE Rangia including BSO's Furniture Yard at Rangia, and office hours only as directed by Engineer-in-Charge.(Note applicable for item Srl No-1.01 to 14.05).

Bed Ply top :FD-246: Top shall be 12 mm thick BWR grade plywood. Make-Archidply/Century Ply/ Greenply.

Head Rest as per drg.

Foot Rest as per drg.

Long Rail as per drg.

Stiffener as per drg.

M&L for french polish with high gloss finish in existing shade after properly cleaned and smoothened the surface by scratching the entire wooden pallets, filling putty to the bore holes where ever required

Chair dining FD-279:- Back rest as per drg

Front legs as per drg

Rear legs as per drg.

Rails as per drg.

Leg stiffner as per drg.

As per item No- 1.06 but for chair dining.

Removing the existing unserviceable cane plastic from the chair and Recanning the chairs by true Godrej pattern with plastic cane 2mm to 2.5mm wide, quality as approved by GE all as specified and as shown on drgs.

Foam with back FD-78M : Seat as per drg.

Back as per drg.

Legs as per drg.

Short rail as per drg.

Long rail as per drg.

Stiffner as per drg.

Vertical stiffner as per drg.

PVC shoes.

Painting of Form with back as per above Note.

Sofa set 5 seater (3+1+1 with cushion) FD-281:- Leg as per drg.

Arm as per drg.

Wooden batten as per drg.

Bearer as per drg.

Taking out old pressed /torn old cushions from sofa set and Supply 40 density thick foam cushion of size 21”x22”x4” duly fixed with the GM fabric as approved by GE.Cushion cover shall be provided with good quality zip stitched on one edge of cushion cover with standard fitting.(Make of Cushion-kurlon/ Sleepwell).

As per item No- 4.05 but for Sofa set 5 seater.

Table dining 6 person FD-273:- Top as per drg.

Legs as per drg

Long rails as per drg

Short rails as per drg

As per item No- 1.06 but for Table dining 6 pers.

Charpoy MS tubing with plytop:- FD/CWE/TEZ/04: Taking out existing broken plywood from the charpoy by loosining the nut bolts with washer. S&F of new 12 mm thick BWR grade plywood fixed to Charpoy with Nut, Bolts, Make of Plywood- Greenply/Century Ply/Archidply

Taking out existing broken head board from charpoy and fixing new head board with 18 mm thick exterior grade prelaminated particle board both side laminated shade as approved by BSO/GE with 4 mm thick teak wood beading in matching shade with new screws.

Repair of dented/scratched parts with grinding, filling putty and smoothening the surface with sand paper.

Hard rubber shoes as per drg

Painting of charpoy MS tubing with plytop as per above note

Charpoy with hard top FD/MAP-II/01:- : Taking out existing broken plywood from the charpoy by loosining the nut bolts with washer. S&F of new 12 mm thick BWR grade plywood fixed to Charpoy with Nut, Bolts,, Make of Plywood- Greenply/Century Ply/Archidply

Repair of dented/scratched parts with grinding, filling putty and smoothening the surface with sand paper.

Hard rubber shoes as per drg

Painting of charpoy MS tubing with plytop as per above note

Charpoy GI Pipe Plytop FD-220 Taking down old unserviceable long rail of GI charpoy and provn of new GI pipe 32mm dia, medium grade ISI marked long rail duly threaded as shown on drg and as directed by Engineer in Charge. Make: Jindal/Parkash Surya/TATA/Sail.

Cutting existing unserviceable long rail retrieved from above and converting into short rails as per existing pattern/design duly threaded at both ends and fixing the same after taking out old unserviceable short rail complete all as specified and directed by Engineer in Charge.

Cutting existing unserviceable short rail retrieved from item above and converting into legs all as per existing pattern/designand drawing duly threaded at one end and fixing the same after taking out old unserviceable leg complete all as specified and directed by Engineer in Charge.

Taking down old unserviceable three way elbow from the GI charpoy & provn of new three-way elbow 32mm dia ISI marked and fixed as per existing design/pattern complete as specified and directed by Engr-in-Charge

Taking down old unserviceable check nuts from the GI Charpoy and provn of new GI heck nuts 32mm dia ISI marked fixed as per existing design/pattern complete all as specified and shown on drg.

Taking down old unserviceable plywood from charpoy GI Pipe ply top. Supply and fixing of ply wood (Size as per drg) on charpoy GI Pipe ply top with nut and bolt all as specified as per drawing and directed by the Engr-in-Charge. (Make of plywood:- Archidply/Greenply/Century)

Locker steel three Unit: FD-127 (M) 3-Way locking system as per drg.

Lock as per existing pattern and shape. Make-Harrison,Godrej

Repairs to dented door by removing the door from hinges making smooth and straight by denting applying putty and refixing by replacing unserviceable hinges.

Supply & Fixing new door by removing the door from hinges, and refixing by replacing unserviceable hinges.

CP Handle as approved by BSO/GE irrespective of what is shown on drg.

Repair and Replacemet of Leg as per drg.

Painting of Locker steel three unit as per Note.

Almirah large steel :FD-1031 & FD/E6/MAP/18:- 3-Way locking system for almirah large as per drg.

Lock as per existing pattern and shape. Make-Harrison,Godrej

CP Handle as approved by BSO/GE irrespective of what is shown on drg.

Leg as per drg.

Repairs to dented door by removing the door from hinges, making smooth and straight by denting applying putty and refixing by replacing unserviceable hinges.

Repairs to existing shelf by opening the clips/rivets of shelf,making smooth and straight by denting applying putty and refixing by replacing unserviceable clips/rivets.

Supply & Fixing new shelf by opening the clips/rivets and refixing by replacing unserviceable clips/rivets.

Supply & Fixing new door by removing the door from hinges, and refixing by replacing unserviceable hinges.

Painting of Almirah large steel as per Note.

Table office Officer steel FD-1003:- Top as per above note.

Legs as per drg.

Long Rails as per drg.

Short Rails as per drg.

Leg Stiffener as per drg.

Drawer as per drg.

Lock as per existing pattern and shape.

Painting of Table office officer steel as per above note.

Table office clk steel FD-1004:- Top as per above note.

Legs as per drg.

Long Rails as per drg.

Short Rails as per drg.

Leg Stiffener as per drg.

Drawer as per drg.

Lock as per existing pattern and shape.

Painting of Table office clk steel as per above note.

Rack Steel 6 Tier FD-1038:- : Repairs to existing shelf by opening the clips/rivets of shelf,making smooth and straight by denting applying putty and refixing by replacing unserviceable clips/rivets.

Supply & Fixing new shelf by opening the clips/rivets and refixing by replacing unserviceable shelf.

Repair of dented/scratched parts with grinding, filling putty and smoothening the surface with sand paper.

Painting of Rack Steel six tier as per above note

Chair writing : FD/E6/MAP/12:- S&F new seat made of 12mm thick BWR grade plywood over which 50 mm thick 32 density foam cushion shall be fixed with pvc lipping all round.The foam and plywood shall also be covered with best qualityfabric as approved by BSO/GE irrespective of what is shown on drg.

S&F new back made of 12mm thick BWR grade plywood over which 50 mm thick 32 density foam cushion shall be fixed with pvc lipping all round.The foam and plywood shall also be covered with best quality fabric as approved by BSO/GE irrespective of what is shown on drg.

Replacement of new arms with polyurethane reinforced with MS insert arms as shown on drgs /existing in chair.

Rubber stoper as per drawing

S & F of new frame of Chair writing as per drawing.

Painting of Chair writing as per above Note.

M/s Narzary Enterprise

M/S KIRAN ENTERPRISE

MS Gautam Construction and CO

M/S S.S. Construction

PURBANCHAL BUILDERS

RK STEEL FABRICATORs

M/s SHARMA BUILDERS & ENGINEERS

M/S Rajkamal Enterprise

M/S K D TURAIHA