Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹30.8 LAccepted-AOC | L1 | Accepted-AOC Being L1 bidder | |
| 2 | L2₹33.9 L+₹1.7 L (5.14%)Rejected-Finance | L2 | Rejected-Finance Being other than L1 bidder | |
| 3 | L3₹36.4 L+₹4.2 L (13.0%)Rejected-Finance | L3 | Rejected-Finance Being other than L1 bidder | |
| 4 | L4₹42.1 L+₹9.8 L (30.5%)Rejected-Finance | L4 | Rejected-Finance Being other than L1 bidder |
Tender Value
₹48.1 L
EMD Value
₹96,200
Closing Date
2 Oct 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 862 EWS
GE 862 EWS Rajouri
SPECIAL REPAIR TO BLDG NO T-119,T-24, T-25 AND T-32 AT CERTAIN UNITS AND PROVN OF RETAINING WALL UNDER AGE BR DETT-B AND AGE EM OF GE 862 EWS
2024_MES_670628_1
GER-51/2024-25
Open Tender
Civil Works
Item Rate
180 days
GE 862 EWS Rajouri
As per tender documents
9 documents required · 9 mandatory
₹500
GE 862 EWS
₹96,200
Yes
5 Nov 2024
3 Sept 2024
4 Oct 2024
3 Sept 2024
2 Oct 2024
18 Sept 2024
3 Sept 2024 - 14 Sept 2024
Amount
Sch 'A' Part-I (B/R works) Taking down cement plaster, any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.
M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete or other than fair faces, finished the surface even and smooth without using extra cement, complete all as specified and directed.
M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surface, finished the surface even and smooth without using extra cement, complete all as specified and directed.
M&L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete/stone surface, finished the surface even and smooth without using extra cement, complete all as specified and directed.
M&L for preparation of new plastered wall surface including cornices and applying two coats of distemper oil emulsion over a coat of primer including 3mm thick wall care putty, complete all as specified and directed by Engineer -in - Charge.
M&L for preparation of newly plastered surface of wall and applying two coats of exterior emulsion weather proof paint of any approved two or more colour pattern (as approved by GE) over and including a coat of primer, complete all as specified and directed by Engineer -in - Charge.
M&L for complete removal of existing treatment on old plastered wall/roof surfaces including cornices and chajjas etc and applying two coats of exterior emulsion weather proof paint of any approved colour pattern over and including a coat of primer, complete all as specified and directed by Engineer -in - Charge.
M&L for complete removal of existing treatment on old plastered wall/ceiling surfaces including cornices and chajjas etc and applying two coats of distemper oil emulsion over a coat of primer including 1mm thick wall care putty, complete all as specified and directed by Engineer -in - Charge.
Taking down chowkhats or frames (without taking off shutters from the frames) exc 1.5 Sqm and n. exc 4 Sqmm each and removing from site, complete all as specified and directed.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Sqm each and removing from site, complete all as specified and directed.
S&F for powder coating of any colour (Thickness or powder coating not less than 50 micron) aluminium door shutters of section weighing not less than 0.55 Kg/M including 5mm thick plain/coloured/frosted sheet glass, ACP sheet and stainless steel wiremesh and conneced items such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, hinges 150mm long 03 nos, suitable handle 02 Nos, tower bolts, mortice lock and door stopper and other accessories as per site requirement complete all as specified and directed.
M&L for 12mm thick prelaminated particle board, interior grade both side decorative choice lamination fixed to aluminium doors or similar works, complete all as specified and directed.
S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and and as directed and as shown on drwaing.
M & L for factory made solid PVC panel door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheety strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded.sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing.
S & F of 100 mm long mild steel butt hinges, medium weight cold rolled fixed/welded to frame (ISI marked) complete all as specified and directed.
S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type (ISI marked), complete all as specified and directed.
S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section (ISI marked), complete all as specified and directed.
S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy (ISI marked), complete all as specified and directed.
S & F 140mm long floor door stopper of brass body and tongue with hard drawn steel spring complete all as specified and directed.
S & F 300mm, mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.
M&L for door bottom sealing strip guard with double sided insulation for doors, which are equally able to keep wind, dust and sound or poluted air out side of door (i.e. Anti Lizard strip) fixed to aluminium or panel door, complete all as specified and directed.
S& F for stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed.
M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified.
S&F for powder coating of any colour (thickness of powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.
S & F for powder coating of any colour (Thickness or powder coating not less than 50 micron) aluminium fixed or openable shutter side hung type without sash bar for windows and ventilator with one or more openable or fixed, aluminium sections weighing 0.55 Kg/M including 5mm thick plain/coloured/frosted sheet glass and stainless steel wiremesh and conneced items such as peg necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long, hinges type B-21, 100mm long 02 Nos, suitable handle 02 Nos, tower bolts, and other accessories as per site requirement complete all as specified and directed.
S&F for Powder coated aluminum three track slinding window with two or more shutter (Minimum thickness of powder coating not less than 50 micron) with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc including 65 X 39.5 X 1.5 mm section for complete frame and rubber beading and glazing clips etc complete as specified and directed by Engr-in-Charge. (Note :- Cost of glass, wiremesh, rubber beading, glazing clips, neoprene packing, fittings such as handles, butt hinges, tower bolts etc will be included in the quoted rate.
S&F for powder coated aluminium grills 6.3mm dia decorative type 75mm mesh size, complete all as specified and directed. (Note:- Minimum thickness of powder coating not less than 50 micron)
S&F for sheet glass 4 mm thick, ordinary quality and fixed with aluminum door windows & ventilators n exc 0.5 sqm in each pane, complete all as specified and directed.
M&L for 2nd class hard wood well seasoned plain solid straight chowkhat framed wrought framed, rebated on the solid, round or chamfered put together with glue and pinned at joint and fixed in wall complete all as specified and directed
M&L in repair for 18 / 19mm thick prelaminated particle board, cupboard, kitchen cabinat shutter etc, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work, complete all as specified and directed.
S&F in repairs 30mm width of flaps continuous (Piano) hinges, mild steel, bright finish or electrogalvanized complete as specified and directed
S & F of 100 mm long extruded anodised aluminium alloy handle, fabricated type (ISI marked), complete all as specified and directed.
S & F of 75 mm long aluminium anodised barrel tower bolt of extruded section (ISI marked), complete all as specified and directed.
S & F of 100mm long hasp and staple, mild steel, safety type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified and directed.
M&L for vitrified tiles light shade, coloured (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles n. exc 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling old tile, complete all as specified and directed.
All as per srl item no 35 here-in-before but in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.
M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4 including dismantling of old tiles, and removing rubbish off the premises complete all as specified and as directed.
M&L for glazed ceramic coloured tiles of size 350x250x7mm / 450x350x7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:4 including dismantling of old tiles, and removing rubbish off the premises complete all as specified and as directed.
M&L for 20mm thick granite black or any other colour, of any type of work (table rubbed and polished) as in steps, jambs, pillars, window - cills, cooking platforms, urinal partition and like set in cement mortar 1:4 including pointed in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including grinding and polishing, laid over and including 15mm thick screed bed in cement mortar 1:4 including dismantling of old granite work, complete all as specified and as directed.
Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.
M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.
M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajjas, shelves, cooking platform and the like including demolition of old RCC works in any position and removing rubbish off the premises, complete all as specified and directed.
M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, incvluding cranking, binding spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per instructions etc including dismantling old existing ceiling board, complete all as specified and directed.
M&L for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down old GI tubing complete all as specifed and directed.
M&L for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down old GI tubing complete all as specifed and directed.
S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed.
S&F in repair gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 15 mm dia complete all as specified and directed.
S&F in repair gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and directed.
S & F in repairs brass chromium plated tubular towel rail 20mm dia 600mm long with and including one pair of brass chromium plated bracket complete all as specifed and directed.
S&F in repair for glass corner shelf with tempered glass, stainless steel brackets and polished chrome finish rail, complete all as specified and directed by Engr-in-Charge.
S&F in repair for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed.
S&F in repair for 15 mm bore bib tap cast copper alloy, chromium plated , fancy type, 'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.
M & L in repairs for 15 mm dia fancy type, chromium plated angle valves, cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specifed and directed.
S&F in repair for 15mm bore Stop valve (concealed type), chromium plated, cast copper alloy screwed down, high pressure with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
S&F in repair for CP shower rose of size 125 mm with swivel joints fixing to steel pipes etc. Complete as all as specified and directed.
S&F in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specifed and directed.
S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.
S & F in repair 15mm CP brass Health faucet with 1.2 meter long stainless steel hose and wall hook alongwith two way brass CP bib cock, screwed down, screwed for iron pipe or female of quarter turn type, complete all as specified and directed by Engr-in-Charge.
Supply and fixing in repair viterous China wash basin, white flat back, size 550x400mm (excluding taps, waste chain and plug and porcelan stopper) but including brackets, including cutting for and pinning in ends of brackets complete all as specified and directed.
S & F in repair for 32mm dia waste coupling, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed complete all as specified and directed.
S&F in repair for 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.
S & F in repair for PVC connection pipe 15mm dia with PTMT nuts of length 600mm complete all as specifed and directed.
S&F in repair for CP soap dish holder of size 100x100x60mm fixed to wall with chromium plated brass screws and wooden/plastic cleats, complete all as specified and directed
S & F in repairs stainless steel curtain rod of 20mm dia complete as specified and directed by Engr-in-Charge.
S & F in repair stainless steel 'T' and 'L' type brackets with finials fixing to wall with MS full screws including wooden/plastic cleats, complete as specified and directed by Engr-in-Charge.
M & L for 75 mm dia cast iron floor trap, with grating fixed with white cement, complete all as specified and directed.
S&F in repair for assembled ready to use rectangular stainless steel (Grade 304) kitchen plate rack with 3-4 shelves, enclosed four sides by SS plain sheet, 0.6 mm squre support pipes, dedicated holes for spoon, pegs etc cover all size 600mmx750mmx250mm of standard pattern, complete all as specified and directed.
S&F in repair for sink with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe, over all size 915mm x 460mm, bowl size 410mm x 330mmx 160mm complete all as specified and directed.
S & F in repairs for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or fixed to wall with suitable size of clamps, complete all as specified and directed.
S & F in repairs for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall with suitable size of clamps, complete all as specified and directed.
S & F in repairs 110mm bore PVC (SWR) bends of any radius with access door, complete all as specified and directed.
S & F in repairs 75mm bore PVC (SWR) bends of any radius with access door, complete all as specified and directed.
M&L for 50mm thick plain cement concrete 1:2:4 type B-1, using 40mm graded stone aggregates as in sub base/ flooring including demolition of old PCC complete all as specified and directed.
M&L for 75mm thick plain cement concrete, type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), including demolition of old PCC, complete all as specified and directed.
M&L in repair for 150 mm internal dia Salt-Glazed stone ware drain pipes grade 'A' laid in trenches over concrete bedding jointed in cement mortar (1:1) and tested ,complete all as specified and directed.
M&L for plain cement concrete 1:4:8, type D-2 ,using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm bore SGSW pipe including demolition of old PCC concrete bed, complete all as specified and directed.
S&F of Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantling of old sheet of any description all as specified and as directed by Engr-in-Charge.
S& F of Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantling of old sheet of any description all as specified and as directed by Engr-in-Charge.
Demolition of plain cement concrete (unreinforced) in any description in ground floor and paving not exc 15cm thick complete all as specified and as directed.
M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed.
M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar 1:6, complete all as specified and directed.
Description all as per srl item no. 83 here-in-before but except stone. Note: Stone retrieved from demolition will be re-used.
M&L for extra over stone walling for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm for lime or sand stone and joints, as specified, of random rubble walling, uncoursed or brought upto courses, complete all as specified and directed.
M&L for raised pointing to random or polygonal rubble stone masonry, uncoursed brought upto courses in cement mortar 1:4, complete all as specified and directed.
S & F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed as in weep holes, complete all as specified and directed.
M&L for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregates) as in surface channel and drains including demolition of old drain, complete all as specified and directed.
Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified and directed.
S&F for powder coated aluminium window and ventilator frame and and one or more shutters fixed / side hung type without sash bar, (minimum thickness of powder coating not less than 50 micron), made out of extruded anodised extruded aluminium section weighing 0.55kg/m, conforming as specified in IS-737, or 65mm x 39.5mm x 1.5mm, fixed with and including anodised aluminium butt hinges 100mm long type B-21, tower bolt, glazing clips, rubber packing, aluminium snap beading, handles, peg stay 150mm long, screws, including 4mm thick plain/coloured/ frosted sheet glass, stainless steel wire cloth and necessary jointing cleats and including making good to the disturbed portion, complete all as specified and directed.
S&F for powder coated aluminium door with frame and shutters (minimum thickness of powder coating not less than 50 micron), made out of extruded anodised extruded aluminium section weighing 0.55kg/m, conforming as specified in IS-737, or 101.6mm x 44.45mm x 1.27mm, fixed with and including anodised aluminium butt hinges, tower bolt, glazing clips and locking arrangement, hydraulic door closer, floor spring, snap beading, handles and 4mm thick plain/coloured/frosted sheet glass, stainless steel wiremesh and connected items, with and including making good to the disturbed portion, complete all as specified and directed.
S&F for powder coated aluminium fixed partition with frame (minimum thickness of powder coating not less than 50 micron), made out of extruded anodised extruded aluminium section conforming as specified in IS-737, or 101.6mm x 44.45mm x 1.27mm thick 101.6mm x 44.45mm x 1.20mm thick with total height upto 3.2m. The panel shall be made out of 5mm thick plain / tinted (frosted) glass in top & bottom or 12mm thick both side laminated particle board including neccessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws etc including making good to the disturbed portion, complete all as specified and directed.
M&L in repair for Joist, channel, angle, MS tubular pipe or tee sections, fixed independently, with or without connecting plates, etc. cut to ordinary lengths i.e. within 20mm of the length indicated, conforming to Fe-290 grade, E-165, complete all as specified and directed.
S & F in repairs for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed for valley/ eaves gutters or rain water pipe with all fittings such as elbow, Equal tee, coupling, Y-section etc including MS clamp for fixing to wall, complete all as specified and directed.
M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.
M & L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc, complete all as specified and directed.
M&L for coloured chequered cement concrete tiles of size 30 cm x 30cm x 25 mm thick set, jointed in neat cement slurry and pigment in floor and pointed in white or coloured (apporved by GE) cement to match the shade of tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 after dismantling of old unserviceable tiles etc and removing rubbish off the premises complete all as specified and as directed.
Excavation over areas n. exc 1.5m depth and getting out in any type of soil, complete all as specified and as directed.
All as per srl item no 98 here-in-before but exc 1.5m and n. exc 3m depth, complete all as specified and as directed.
M&L for plain cement concrete 1:2:4, type B-1, (using 20mm graded stone aggregate) as in quoin blocks, strings courses, copings, kneelers, apex stone, bed plated , surface channel and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work ,complete all as specified and directed.
M&L for plain cement concrete 1:3:6, type C-1 using 20mm graded stone aggregates as in bonders for stone walling and similar articles with plain faces, and set in CM 1:6, complete all as specified and directed.
M&L for broken stone or boulder hand packing (any thickness) at back of wall over arches etc, complete all as specified and directed.
Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick , complete all as specified and as directed.
Removing excavated material ,not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting poin, complete all as specified and directed.
S & F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.
S&F for 4mm dia galvanised steel wire size 150 X 100 mm mesh made up into mattresses or cages, lapped wired and laid in position including closing after filling (as per sample approved by GE) complete all as specified and directed.
M&L for cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in surface channel and drains, complete all as specified and directed.
M&L for formwork of faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses etc vertical with fair finished surface, complete all as specified and directed.
Sch 'A' Part-II (E/M works) Taking down carefully copper/ aluminum point wiring (light, fan, bell, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications, complete all as specified and directed.
M&L for point wiring for one light point/fan point/bell point controlled by one-one way switch with 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including PVC casing caping medium grade of 25mm width complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making good the diturbed surfaces to match with the existing, compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of casing capping measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth)
Description all as per Serial item No 110 above but for one 3 pin 6 Amp socket outlet on independent board controlled by one 6 amp switch, complete all as specified and directed.
Description all as per Serial item No 110 above but for one 3 pin 6 Amp socket outlet on same board controlled by one 6 amp switch, complete all as specified and directed.
Description all as per Serial item No 110 above but for one 3 pin 16 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper conductor cable with 2.5 sqmm single core multistraind FRLS copper conductor cable as earthling lead, complete all as specified and directed.
M&L for modular point wiring for light /fan point complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through PVC conduit of suitable size as required at site, with fittings such as tee, corners, overlapping, connectors, etc fixed over walls, ceiling, floors etc including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty and fabricated branded modular metal flush boxes with modular white cover plate and frame concealed in walls with suitable modular fitting housing switches, socket outlet and fan regulators etc, complete all as specified and directed. (Note:- Three run of copper conductor of required size and and colour coding of wiring to be followed as red/yellow/ blue for phase, black of neutral and green for earth)
Description all as per Serial item No 114 above but for one 3 pin 6 Amp socket outlet on same board controlled by one 6 amp switch, complete all as specified and directed.
Description all as per Serial item No 114 above but for one 3 pin 6 Amp socket outlet on independent board controlled by one 6 amp switch, complete all as specified and directed.
Description all as per Serial item No 114 above but for one 3 pin 16 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper conductor cable with 2.5 sqmm single core multistraind FRLS copper conductor cable as earthling lead, complete all as specified and directed.
S&F for switch piano flush type single pole one way 5 amps 240 volts, complete all as specified and directed.
S&F for socket outlet 2 in 1, 5 pin, 6 amp flush type, complete all as specified and directed.
S&F for switch piano flush type single pole one way 15 amps 240 volts, complete all as specified and directed.
S&F for switch socket combination 2 in 1, 5 pin, 5/15 amp flush type, single pole, 240 volts, complete all as specified and directed.
S&F for fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically, complete all as specified and directed.
S&F for modular switch 6 Amps, one way, one module, complete all as specified and directed.
S&F for modular switch 16 Amps, one way, one module, complete all as specified and directed.
S&F for modular socket outlet combination 2/3 pin, 6 Amp , 230 volts, 2 module complete all as specified and directed.
S&F for modular socket outlet combination 6 pin, 6/16 Amp , 230 volts, 2 module complete all as specified and directed.
S&F for modular stepped type fan regulator electronic, 100 watt, 2 module, complete all as specified and directed.
S&F for ceiling rose 3 phase/PVC/polycarbonate isolated body surface bakelite 2 to 3 terminals, complete all as specified and directed.
S&F for lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/angular/pendent fittings including LED inverter bulb 9watt, B22, CDL, 240 volts, complete all as specified and directed.
M&L in repair for LED Tube light fitting, complete with 1x 20 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height, complete all as specified and directed.
S&F in repair for LED building security light 20 watts, 240volts, AC, outdoor type with high pressure diecast housing with individual LEDs as light source and lence embedded PC cover having Top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 complete with connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable size 1.0 Sqmm, complete as in repeir all as specified and directed
S&F in replacement for exhaust fan of 250mm sweep, heavy duty, 1200 RPM electrical operated 230 Volts AC single phase, made of sturdy engineering plastic complete with louvers shutter etc, complete all as specified and directed.
S&F in replacement for MCB distribution board SPN 8 way, double door 240 volts duly painted with epoxy based powder coated painting suitable for mounting MCB DP/SPN as incomer and MCB SP/DP as outgoings complete with 200 amp rated busbar, neutral bar, earth bar connecting cable links with top and bottom removable gland plate with IP 42 protection complete all as specified and directed. (Note:- MCBs will be measured separately.)
M&L in repair for MCB single pole 5 to 40 amp, 240 volts, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.
M&L in repair for MCB single pole & neutral 40 amp, 240 volts, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.
M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion including taking down existing unserviceable earthing complete all as specified. (Note:-Earth strip and protection pipe upto board is included in the quoted rate)
Taking down ceiling fan of size 1200/1400 mm sweep and dismantling blades and removing fan and blades to store and painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust and refixing fans in same position including connecting to electric system and testing complete all as specified and directed.
S&F in repairs recess mounting 6500k light fittings LED 36 watts 2x2 panel surface/ recess mounting light fitting LED backlit with high efficient LEDs & glare free opal diffuser IP-20, internally prewired, 230V, complete with all accessories such as electronic driver, connector block etc and neccessary fixing arrangement at any height, complete all as specified and directed. Note: Material required such as safety harness, ladder and T&P etc will be provided by the contractor without any extra cost.
M&L in repair for LED Tube light fitting, 1x 10 watts, 220V, AC, complete with 2 feet decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body,enviromental friendly, energy efficient ready to use pack complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height, complete all as specified and directed.
S&F in repair for environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head 1x10 watt 6000 K inbuilt LED luminaire comprising of high brightness LEDs, IP54 protection including connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.
Supply,laying, jointng, connecting, testing and commissioning, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 16 sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands , complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).
M&L in repair for 40mm dia galvanized steel tubing (medium grade) with complete all fittings such as elbow, unions, nipples, tees, bends, short pieces, connections, check-nuts, caps, plugs, diminishing pieces and flanges etc as in pole, crossing of roads, laid in trenches, fixed on walls with clamps nut, bolts and washer etc for protection of cables, complete all as specified and directed.
S&F in repair for LED street light fitting 35 watts, 240volts, AC, outdoor type with high pressure diecast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including three core 0.5 sqmm copper cable from connector to fitting, complete as in repeir all as specified and directed
Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth not exceeding 10sqm on plan for laying of cable and foundation of poles stays and getting out in soft / loose soil complete all as specified and directed.
Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm (soil) thickness all as specified and directed.
Removing of excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.
M&L for dry sand cushioning to underground cable, provided with a layer 8 cm thick before and 15 cm deep after laying and stretching jointing and testing the cable, complete all as specified and as directed (Note: Punned thickness of sand shall be measured and paid).
M&L in replacement for brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat, size 230mmx115mmx75mm over the cable abutting each other, complete all as specified and as directed.
M/S RAHUL GUPTA (BID ID -3124909)
M/s Anil Engineers & Builders (BID ID -3125290)
VIJAY KUMAR SURI AND SONS (BID ID -3123647)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .