Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹42.4 LAccepted-AOC | L1 | Accepted-AOC Due to lowest bidder | |
| 2 | L2₹43.7 L+₹26,695.50 (0.62%)Rejected-Finance | L2 | Rejected-Finance Due to not lowest bidder |
Tender Value
₹49.7 L
EMD Value
₹99,320
Closing Date
7 Oct 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (N) BIKANER
GE (N) BIKANER RAJASTHAN
SPL REPAIR TO STORE BLDG AND ADDITION ALTRATION TO MESS BUILDING AT BIKANER MIL STN UNDER AGE BR 1 OF GE N BIKANER
2023_MES_618088_1
GE (N) BKN-TOKEN/53/2023-24
Open Tender
Miscellaneous Works
Item Rate
270 days
GE (N) BIKANER
As per Tender Documents
6 documents required · 6 mandatory
₹500
GE (N) BIKANER
₹99,320
Yes
13 Jan 2024
9 Sept 2023
16 Oct 2023
9 Sept 2023
7 Oct 2023
25 Sept 2023
Amount
Demolition of reinforced cement concrete to any description and in any position(reinforcement cut as required to facilitate demolition.
Demolition of cement concrete in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.
Demolition of lime concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.
Dismantling existing / flooring hearth or wall tiling including cement mortar bedding (except serviceable tiles or tiles which are in good condition) complete all as specified and as directed by engineer in charge.
Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified. (Note:- While demolition proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
Demolition of brick/stone masonry built in CM. complete all as specified and as directed by engineer in charge.
Demolition of brick tiles or terracing tiles,on roofs complete all as specified and as directed by engineer in charge.
Demolition of stone slab of any description or thickness in floors, aprons laid,bedded and pointed in any mortar complete all as specified and as directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by engineer in charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), all as specified and directed by Engineer-in Charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.
Taking down shutter only exc 1.00sqm but nexc 2.00 sqm preserve it properly in the store and refixing in the same opening with necessary repairs or changes complete all as specified and as directed.
Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips including providing and fixing new ones complete all as specified and as directed by Engineer-in-Charge.
Taking up or down steel tubing 15 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified and as directed by engineer in charge.
Taking up or down steel tubing 20 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified and as directed by engineer in charge.
Dismantling cast iron /PVC pipes fixed to walls or laid in trenches in any position complete all as specified and as directed by engineer in charge.
Dismantling water tanks and removing to store exc 250 ltrs and nexc 500 ltrs complete all as specified and as directed by engineer in charge.
Dismantling water tanks and removing to store exc 500 ltrs and nexc 1000 ltrs complete all as specified and as directed by engineer in charge.
Cutting through holes into through cement concrete slabs chajjas etc reinforced or other wise exc 100 sqcm but nexc 250.00 sqcm complete all as specified and as directed by engineer in charge.
Cutting existing steel tubing for alterations or additions done in position without taking down for 10mm to 40 dia pipe (Each cut measured) complete all as specified and as directed by engineer in charge.
M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggreagate as in foundations, filling and mass concrete complete all as specified and as directed.
M&L 75mm thick PCC 1:4:8 type D-2 using 40mm gaded stone aggregate as in sub base of floors complete all as specified and as directed.
M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified. (Note:- While doing reinforcement work proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
M&L for TMT bars 5 mm to 10 mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified. (Note:- While doing reinforcement work proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
All as per Item no. 24 here in before but 6 to 8mm dia in stirrups , spacers, and binders complete all as specified. (Note:- While doing reinforcement work proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
M&L for reinforced cement conc M-25 design mix as in beams , cantilevers over span 1.5m landings , balconies & chajjas etc complete all as specified and as directed. (Note:- While doing RCC work proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
M&L for reinforced cement conc M-25 design mix as in slab supported on walls , beam, and columns in floors,roofs landings , balconies etc (Note:- While doing RCC work proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
M&L of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, all as specified . (Note:- While doing RCC formwork proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
Form work to sides and soffits of roof beams incl supports over hangs etc finished rough (Note:- While doing RCC formwork proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
Form work to edges of concrete flats, breaks ,conc railing nexc 200mm wide finished roughthick (Note:- While doing RCC formwork proper gunny bags filled with sand will be laid on floor and all necessary arrangements will be done so that ground floor should not damage at no extra cost.)
M&L for 10 mm thick Rendering in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)
Supply only Liqued integral water proofing compound complete all as specified and as directed by engineer in charge.
S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified .(As directed by Eng-in-charge)
Lime concrete terracing as specified on roof complete all as specified and as directed by engineer in charge.
Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm incl cleaning surface complete all as specified and directed.
40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.
M&L Cement concrete 50 mm thick type B-1, 1:2:4 (20 mm graded aggregate) as in bedding layer/ levelling course or protection to roof treatment laid in pannels and Forming Contraction (Dummy) joints 30mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by Engr-in-Charge
M&L for Terrazzo tiles 20cm x 20cm x 20mm thick, with grey cement and pigments size of chips upto 12mm; set, jointed and pointed in neat cement slurry in floors, and cut and polished complete all as specified.
M&L for 7.5cm Bheelwada/sand stone slabs in sunshades, chajjas, shelvel, cills, landings, cover, stones, templates etc, n exc, 2m in length, punched dressed on face and along exposed ecges, self faced on other side in cm mortar 1:4 complete all as specified and as directed.
M&L Mild steel frame work such as grills, grating etc. with ends of bars shouldered and or riveted, or forged into spikes : framed guard bars, barred iron doors, ladders, railings and similar work conforming to Fe – 290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.
M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 complete all as specified and as directed by engineer in charge.
M&L for brick work with Fly Ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:4complete all as specified and as directed by engineer in charge.
M&L for brick work with Fly Ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and as directed by engineer in charge.
M&L for brick work with Fly Ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:4 in half brick thick wall complete all as specified and as directed by engineer in charge.
Ditto all as per serial item No 44.00 here-in-before but except bricks. Note : Old serviceable burnt clay / fly ash bricks retrieved from serial item No. 6.00 here-in-before shall be used under this item.
M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).
M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge.
M&L for Rendering 15mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.
M&L for Rendering 15mm thick on brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge.
M&L for Rendering 20 mm thick on brick work or lime stone masonary or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).
M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge.
Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, complete all as specified and as directed by engineer in charge.
M&L for 100 mm thick cement concrete type B-2 ,1:2:4 (20 mm graded aggregate) laid to alternate pannels and making surface even and fair complete all as Eng-in-Charge .
M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, levelling course, etc, surface finished fair and even, complete all as specified and as directed.
M&L for 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles on vetical surface complete all as specified and as directed by engineer in charge.
M&L for Digital coloured vitrified tiles (size exceeding 0.36 sqm and nexc 0.99 sqm ) and10mm thick as in floors jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces incl 15mm thick in cement mortar 1:4 complete all as specified and as directed by engineer in charge.
M&L for Digital coloured vitrified tiles (size exceeding 0.36 sqm and nexc 0.99 sqm ) and10mm thick as in skirting jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces including 10mm thick rendering in cement mortar 1:3 complete all as specified and as directed. Note:The contractor shall have no claim on difference what so ever on shade /colour of tile)
M&L for Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed by engineer in charge.
M&L for joint free non skid ceramic tiles (coloured ) 7 to 8 mm thick , area of each tile exceeding 0.18 sqm but not exc 0.38 sqm as in floors, stet and jointed in neat cement slurry and pointed in shete or coloured cement to match the shade of tiles over & incl 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for glazed ceremic tiles (coloured) 7mm thick , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (ie 450mm X 300mm or as directed) , on vertical surfaces such as dado , skirting etc, set and jointed in neat cemnt slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed )m in cement & sand mortar 1:3 complete all as specified and directed.
M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.
M&L for machine cut Kota stone slab 18 to 20mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.
Moulding of kota /marble stone full round complete all as specified and as directed by engineer in charge.
Grinding and Polishing of kota /marble stone flooring complete all as directed and as specified by Engr In Charge.
M&L for 10 mm thick screed bedding in cement mortar 1:4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns complete all as specified and as directed by engineer in charge. ( WPC to be measured separately as supply only)
S&F 20mm thick Granite (of any type) tiles machine cut , in slabs,steps, skirting dado including cutting bullnosing & polishing laid over cement screed and jointed with grey cement slurry and pointed with white or grey cement with admixture pigment to match the shade of slab incl making hole for gas pipe complete all as specified and as directed by engineer in charge.
M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified
M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified
M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified.
M&L for factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.
M&L for factory made Glazes and skelton,(35mm)open rebated and prepaired to recive glass,gauze etc.(without sash bars) edge or framing plain, chamferd or rounded fitted with cut and mitreds beads for securing glass complete all as specified and as directed by engineer in charge.
S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads / steel windowsin squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed by engineer in charge.
S&F anodised aluminium frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing glass , handles complete all as specified and as directed by engineer in charge.
S&F Sheet glass, ordinary quality 5.5 mm thick for Aluminium door ,window and Vent.and glazing in square n exc 0.5 sq.m in each pane complete all as specified and as directed by engineer in charge.
S&F Neoprene/ EPDM rubber gasket for fixing sheet glass complete all as specified and as directed by engineer in charge.
S&F Stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by engineer in charge.
S&F Stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repairwith stainless steel wire staples complete all as specified and as directed by engineer in charge.
S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and avg width of aperture1.18mm complete all as specified and as directed by engineer in charge.
S&F MS bow handle oval type handles 150mm size complete all as specified and as directed by engineer in charge.
Material and labour for 150mm Mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed by engineer in charge.
S&F for 150mm size Mild steel barrel tower blots, stove enamelled black, with bright bolt and fixed complete all as specified and as directed by engineer in charge.
M&L for MS sliding door bolts 250mm size, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and as directed by engineer in charge.
M&L for MS sliding door bolts 300mm size, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and as directed by engineer in charge.
S&F factory made mild steel Window box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided
S&F factory made mild steel Ventilator box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately
S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation complete all as specified and as directed by engineer in charge.
S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified and with provn of cooler stand.
S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type C-22 of 100mm complete all as specified and as directed by engineer in charge.
S&F Aluminium anodised barrel tower bolt of extruded section of 150mm complete all as specified and as directed by engineer in charge.
S&F Aluminium handles cast type anodised of 150mm complete all as specified and as directed by engineer in charge.
S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed
S&F Prelaminated Block boards 19 mm grading 2 quality interior garde commercial type for cup boards fixed with screw to timber frame work with decorative film mica face veneer on both side face with proper cover fillet or beading with standard hard board 4. 5 mm thick bording plain on side with butt joints with including complete.block complete all as specified and as directed by engineer in charge.
S&F Aluminium anodised barrel tower bolt of extruded section of 75mm complete all as specified and as directed by engineer in charge.
S&F Aluminium handles cast type anodised of 75 mm complete all as specified and as directed by engineer in charge.
S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed by engineer in charge.
S&F 75mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed by engineer in charge.
M&L for 15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.
M&L for 20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20 mm complete all as specified.
Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall complete all as specified and directed by Engr-in-charge
S&F 75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 complete all as specified and as directed by engineer in charge.
M&L for 25mm thick cement concrete type B-0, 1:2:4(12.50mm graded stone agg )making surfaces even and fair or bedding layer / levelling course complete all as specified and as directed by Engr-in-Charge.
S&F 100mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 complete all as specified and as directed by engineer in charge.
S&F 75mm bore sand cast iron waste pipe any length with or without ears laid in floor complete all as specified and as directed by engineer in charge.
S&F 75mm bore sand cast iron waste pipe any length with or without ears fixed to walls complete all as specified and as directed by engineer in charge.
S&F 100mm bore sand cast iron waste pipe any length with or without ears fixed to walls complete all as specified and as directed by engineer in charge.
S&F100mm bore sand cast iron waste pipe any length with or without ears laid in floor complete all as specified and as directed by engineer in charge.
S&F 100mm bore CI sand cast iron branch piece single (Equal or un equal) oridinary or inverted with parallel branches complete all as specified and as directed by engineer in charge.
S&F 75mm bore CI sand cast iron branch piece single (Equal or un equal) oridinary or inverted with parallel branches complete all as specified and as directed by engineer in charge.
S&F sand cast iron bend (any radius) 100mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors complete all as specified and as directed by engineer in charge.
S&F sand cast iron bend (any radius) 75mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors complete all as specified and as directed by engineer in charge.
S&F cast iron cowl 75 mm bore complete all as specified and as directed by engineer in charge.
S&F in repair PVC Pipe Pipe (SWR) bends (any radius), disminishing pieces or tappers(larger bore measures), 110mm dia with access door complete all as specified and as directed by engineer in charge.
S&F in repair PVC Pipe Pipe (SWR) branch pieces ,Double (equal or unequal ) ordinary or inverted (spigot or socket type) or with parallel branches 110 mm dia complete all as specified and as directed by engineer in charge.
PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring jointed fixed to walls complete all as specified and as directed by engineer in charge.
S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm bore pipe complete all as specified and as directed by engineer in charge.
S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 75mm bore pipe complete all as specified and as directed by engineer in charge.
S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position two layer ,ISI marked all as specified in SSR Part I of 500 Ltr complet all as specified and as directed.
S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm complete all as specified and as directed by engineer in charge. Make : Prayag or equivalent.
S&F Vitreous china wash down water closet pan (pedestal pattern), white excluding flushing cistern and flush pipe) incl. P or S trap complete all as specified (Make Cera or equivalent).
S & F PVC valveless syphonic action type flushing cistern, 10 ltr capacity low level , white with inlet, ball valve, float and handle including brackets fixed in repairs complete all as specified and as directed by engineer in charge.
S&F Plastic water closet seat,white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by engineer in charge.
S&F in repair Vitreous china wash basin, white flat back, size 580x450 excluding traps waste pipe fixed with brackets complete all as specified and as directed by engineer in charge. (Make Cera or equivalent)
S&F in repair 32mm/38mm bore waste fittings brass chromium plated for wash hand basin / sink etc with long screwed shand and flynuts complete all as specified and as directed by engineer in charge. (Make Jaquar or equivalent)
S&F Waste pipe 32mm for WHB for coupling fixed in repair complete all as specified and as directed by engineer in charge.
S&F in repair 32 mm size cp waste coupling (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) incl waste pipe complete all as specified and as directed by engineer in charge.
S&F brass CP wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore complete all as specified and as directed by engineer in charge. (Make : Parryware or Hindware or equivalent).
S&F brass CP WHB mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore complete all as specifie and as directed by Engr-in-charge . (Make : Parryware or Hindware or equivalent).
S&F CP Health Faucet fixed type suitable for EWCs with 1,5 mtr stainless steel tube complete all as specified and directed by Engineer-in-charge of MAKE : JAQUAR, PRAYAG
S&F CP toilet paper holder fancy type complete all as specified and directed by Engineer-in-charge.MAKE: JAQUAR OR EQUIVALENT
S & F glass corner of size 300mmx300mm with 5.5 mm thick glass and steelness steel clip and steelness steel railing allround the shelf complete all as specified and directed by engineer in charge .
S&F sheet glass shelf assembly in repair , oconsisting of 5.5 mm thick sheet glass shelf 12 cm wide chromium plated bracket guard and railing 60 cm long complete all as specified.
Chromium plated soap dish complete all as specified and directed by Engineer-in-charge.
S&F Aluminium snake bead with bush duly fitted with screws with length equal to door width as specified and directed by Engr-in-Charge
S&F Brass chromium plated shower rose 125 mm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engineer in charge.MAKE: JAQUAR OR EQUIVALENT
S&F Brass chromium plated shower arm 15 mm 195 mm long with bend 45 degree mm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engineer in charge. MAKE: JAQUAR OR EQUIVALENT
S&F in repair 15mm Stop valve brass fancy type concealed type stop valve chromium plated with long shank and complete screwed for iron pipe.(Make Jaquar or equivalent)
S&F in repair bib taps chromium plated fancy type 15mm bore long neck with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed (Make Jaquar or equivalent)
S&F tubular Towel rail brass chromium plated , 20mm dia D type 600mm long between flanges of cast copper alloy, chromium plated brass screws, fixed in repair complete all as specified and directed by Engineer-in-charge.
S&F for peg set of Six of best quality complete all as specified and as directed by engineer in charge.
S&F in repair Chromium plated stop cock/Angle Valve, with crutch or butterfly handle screwed down for iron pipe or brass ferrule fancy type , CP 15mm dia complete all as specified and as directed by engineer in charge.(Make Jaquar or equivalent)
S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by engineer in charge. (Make Jaquar or equivalent)
S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by engineer in charge. (Make Jaquar or equivalent)
S&F in repair Chromium plated Two way Angle Valve, with crutch or butterfly handle screwed down for iron pipe or brass ferrule fancy type , CP 15mm dia complete all as specified and as directed by engineer in charge. (Make Jaquar or equivalent)
S&F in repair for 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by engineer in charge.
S&F in repair for 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by engineer in charge.
S&F in repair for 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by engineer in charge.
Materal and labour for construction of brick masonary valve pit chamber of size 900x900x600 mm (Internal dimension) using sub class ,B, bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, brick masonary sub class bricks 23 cm build n cement mortar and below ground level PCC with 1:2:4 type B2 using 20mm grade stone aggregate, copng 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys, painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation, returning & filling & removing of surplus soil etc complete all as specified and as dircted by Engineer in Charge.
S&F in repair Stop valve cast copper alloy screwed down , high ressure wit crutch or butterfly handle , screwed both ends for iron pipe or for unions or 15mm dia complete all as specified and as directed by engineer in charge. (Make Jaquar or equivalent)
Supply and fix floor door stopper of aluminium alloy body, overall length of cover plate 140 mm and tongue anodised with hard drawn steel sring fixed in floor complete all as specified and as directed by engineer in charge.
S&F in replacement curtain rod 20 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and as directed by Engineer-in-Charge. Note:- The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.
Cutting opening through brick walls for door , window and other opening or enlarging existing opening,converting window into door opening etc. cutting out deffective brick work for under pinning including providing fixing and removing shoring cleaned and stacking bricks removing surplus servicable brick,hard core complete all as specified and as directed by engineer in charge.
M&L for providing 75 mm thick cement concrete 1:3:6 type C-2 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed by engineer in charge.
M&LProviding cement concrete 1:2:4 mix type B-1(20mm graded crushed stone aggregate in Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by engineer in charge.
M&L for providing at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and as directed by engineer in charge.(Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)
M&L for 25 to 30mm thick Plaster of Paris (POP) (Gypsum anhydrous) raised moulding to flat surface of ceilung including preparation of surfaces complete all as specified and as directed by engineer in charge.
M&L for treatment of soil under existing floors using emulsion @ one litre per hole , 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floors complete all as specified and as directed by engineer in charge.
M&L for providing at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and as directed by engineer in charge.(Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)
M&L for two coats of synthetic enamel paint on new steel surfaces including preparation of surfaces over a coat of red oxide Zinc chrome primer complete all as specified and as directed by engineer in charge.
M&L for preparation of new wooden surfaces and applying two coats of synthetical enamel paint over a coat of pink primer complete all as specified and as directed by engineer in charge.
M&L two coats of cement cement base paint on walls including preparation on new surfaces complete all as specified and as directed by engineer in charge.
M&L complete removal of old painted plastered or unplastered surface of wall of any description including cornices, pilasters etc and applying two coat of weater proof paint (Apex) approved quality incl a coat of primer complete alll as specified and as directed by Engineer in Charge.
M&L for Preparing new plastered or unplastered surfaces of walls and applying two coat of weater proof paint (Apex) approved quality & including a coat of primer complete all as specified and as directed by engineer in charge.
M&L Preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash complete all as specified and as directed by engineer in charge.
M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified and as directed by engineer in charge.
M&L for applying two coats of white washing on ceiling including preparation of new plastered surfaces complete all as specified and as directed by engineer in charge.
M&L for Preparing new plastered or unplastered surfaces of cieling and applying two coats of distemper oil emulsionr tinted over & incl Chalk whiting, on plastered surfaces, prepara-tory to distempering complete all as specified and as directed by engineer in charge.
M&L for Preparing old plastered or unplastered surface of cieling and applying two coats of distemper oil emulsionr tinted over & incl Chalk whiting, on plastered surfaces, prepara-tory to distempering complete all as specified and as directed by engineer in charge.
Preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiting incl 3mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge.
Preparation of old plastered or unplastered surface of wall and applying one coats of distemper oil emulsion, white or tinted over a coat of chalk whiting incl 3mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge.
Sand filling under floors or in foundation or in floor for storing FOL including watering and consolidation or for raising height of floor if reqd complete all as specified and as directed by engineer in charge.
M&L for providing and injecting chemical emulsion for Post constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 ltr per sqm of the vertical surface of the sub structure to a depth of 300 mm including excavated channel along the wall and rodding etc complete. (Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)
M&L for providing and injecting Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors .(Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)
Raking out to stone slab as in roof stone patti or precast concrete slab floor, any description, laid flat complete all as specified and as directed by engineer in charge.
M&L for Jodhpur stone of roof slabs, self faced 7.5 cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by engineer in charge.
M&L for Jodhpur stone for lintels, beams and roofs, self faced, 7.5 to 10cm thick complete all as specified and as directed by engineer in charge.
Rough dressed sand stone slab 20 to 25 mm as in chajja but jointed and pointed in cement mortar 1:3 complete all as specified and as directed by engineer in charge.
M&L hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spread and levelled in layer n exc. 15 cm thick watered and rammed to a true surface complete all as specified and as directed by engineer in charge.
M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade to IS 15658-2006 manufactured using grey cement and no pigment complete all as spcified and directed.
Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.
Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed.
Taking down old U/S existing VTPN 4way, DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.
M & L for point wiring for one light/fan/bell/buzzer point controlled by one way switch with 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) including 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) as continues earth wire in green colour to coomon earth dolly laid/drawn into and including non metalic rigid PVC concealed conduit (medium duty, ISI marked not less than 20 mm dia) with all fittings such as tee, bends etc all as per IS terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular Switches, sockets, regulators etc with and including modular cover plates with frame of requisite modules all as specified and as directed: Notes:- (i) Cost of cutting/leaving forming chases for conduit, sinking for metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed for include for modular metal flush boxes of requisite module and modular cover plate with frame of requisite module of colour as approved by GE
(b) One 3 pin 5 amps socket on independent board.
(c) One 3 pin 5 amps socket on same board.
Ditto all as per item No 183 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .
Ditto all as per item No 183 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .
S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.
S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.
M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.
M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.
S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.
S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.
Removing and re-fixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.
S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.
Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by engineer in charge.
M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engineer in charge.
S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge.
Supply and fixing Bell push, modular type, 5 amp 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.
Supply and fixing Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed by Engr-In-Charge.
Supply and fix Modular Telephone socket with shutter 1 M white complete all as specified and directed by Engr-In-Charge.
Supply and fix Modular TV Coaxial Socket 1 M White complete all as specified and as directed by engineer in charge.
Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by engineer in charge.
S&F dimmable touch LED table lamp 6 Watt with 3 level adjustable brightness desk lamp with touch sensor switch, with & including all standard accessories, prewired and connecting up, complete all as specified and as directed by engineer in charge.
Supply & fix LED Wall light 12W, sun / prismatic made up of unbreakable poly carbonate suitable for mounting on wall/ surface omplete all as specified and directed by Engineer-in-charge.
S&F LED Bulb 9W, operating voltage- 220-240 volts, starting time < 0.5s, color temperature-6500K, lumens: min 825 complete all as specified and directed by Engineer-in-charge.
Taking down fan,sealing cable end,dismantling blades of any make, any sweep, complete all as specified and as directed by engineer in charge.
Supply and hanging/fixing ceiling fan 1200mm sweep AC supply (input voltage range 120 to 280v), BLDC type, 5 star rated BEE and ISI marked, super enameled copper winding of 'B' class insulation, single phase 20 watt (+ 10%), PF 0.90 (MIN), air delivery of 220 CUM per min (CMM), 350 RPM (+ 10%), TEMP RISE 40 DEGREE MAX, without remote, with electronic regulator, 3 blades, down rod including accessories, total harmonic less than 10%, 5 speed, hanging in position, including making connection wih and including flexible cord twin core twisted copper conductor of size 23/0.0076 from cealing rose to fan complete all as specified and as directed. Note :- (i) Sl No of cealing fan and GE office name shall also be writing on fan with red colour permanant marker. Cost for the same shall deemed to be included in quoted unit rate. Nothing shall be paid extra on this account.
supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed by engineer in charge.
Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by engineer in charge.
S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.
Taking down Geyser of any capacity from wall and deposited to store complete all as specified and directed by Engineer-in-Charge.
S & F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve,thermostate,NRV ,TOP PLUG 20AMP with valve flange suitable for 15mm bore pipe for water supply connection complete all as specified and as directed by engineer in charge.
S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar complete all as specified and as directed by engineer in charge.
S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.
S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.
S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.
S&F MCCB 63 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.
S&F MCCB 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.
M & L for invertor point wiring for light/fan/mobile charging point with 2.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) complete all as specified and as directed by Engr-in-charge.
Taking dowen and refixing tamper proof energy meter electronic type single phase 10-60 Amps current rating single phase 230V AC with electric connection and necessary fixing arrangement complete all as specified and directed.
M&L for submain wiring with 4 runs of 10.0 Sqmm (nominal area) size main cable & 1 runs of 10.0 Sqmm size earth continuity conductor single core PVC insulated unsheathed FRLSH multistranded copper conductor 1100 volt grade ISI marked cable drawn through & including suitable size of heavy duty non metalic rigid PVC concealed conduit ISI marked & conduit fittings/accessories, fixede concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified & directed. Note :-(i) 04 runs of 10.0 Sqmm size main cable, 01 run of 10.0 Sqmm size earth continuity conductor cable & Conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall be included in quoted rate of this item.
M&L for submain wiring with 2 runs of 6.0 Sqmm (nominal area) size main cable & 1 runs of 6.0 Sqmm size earth continuity conductor single core PVC insulated unsheathed FRLSH multistranded copper conductor 1100 volt grade ISI marked cable drawn through & including suitable size of heavy duty non metalic rigid PVC concealed conduit ISI marked & conduit fittings/accessories, fixede concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified & directed. all as specified & directed. Note :-(i) 02 runs of 6.0 Sqmm size main cable, 01 run of 6.0 Sqmm size earth continuity conductor cable & Conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall be included in quoted rate of this item.
M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.
Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 3.5 core x 35 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.
Supplying and laying un-reinforced precast concrete cable cover, class LVP,type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and as directed by engineer in charge.
M&L for Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 cm spread thickness (8 cm in depth before laying the cable and 15 cm in depth after laying the cable) and consolidated (punned) upto 180 mm thickness, complete all as specified and as directed. Note : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for.
Supply and fixing GI Pipe light grade og Size 80 mm bore with all fittings for passing of cables fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable all as specified and directed.
Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m wide for laying of GI tubes etc and getting out in soft/ dense soil complete all as specified and as directed by engineer in charge.
Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and as directed by engineer in charge.
Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.
Removing excavated soil/Demolished material to a distance n.exc 2.5 Km and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.
M/s Sharafat Farook
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .