Construction of Runway and allied links parallel to existing runway at HAL, Nashik

Essential/ Prequalification Criteria

Annual Turnover: Average annual financial turnover during the last 3 years, ending 31.03.2025 should be at least 30% of the approximate estimated amount put to tender. (i.e ₹ In Lakhs)

Turn over (Rs. In Lakhs)

Profit & loss statement duly certified by chartered accountant with UDIN shall be considered for evaluation of turnover for the respective financial Year.

Solvency : The solvency required will be 40% of the approximate estimated amount put to tender. The solvency certificate shall be from a nationalized or scheduled bank and issued within a period of 12 Months from the final date of submission of the tender i.e ₹ In Lakhs

Related Document to be Uploaded to eProcurement Portal.

Not meeting eligible criteria

Experience Experience of having successfully completed similar works(Refer NIT "Work Details") during last 7 years ending on the previous day of last day of submission of tender should be either of the following: [Latest work experience certificate may be uploaded] a) Three similar completed works each costing not less than the amount equal to 40% of the approx. estimated amount put to tender against each work in the tender notice. (Or) b) Two similar completed works each costing not less than the amount equal to 50% of the approx. estimated amount put to tender against each work in the tender notice. (Or) c) One similar completed work costing not less than the amount equal to 80% of the approx. estimated amount put to tender against each work in the tender notice.

40% (Three Works)

Type of Work: [Incase of private works the same shall be supported with TDS certificate]

Type of Work: [Incase of private works the same shall be supported with TDS certificate]

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

GST No Registration Number.

ESIC Registration Number

EPF Registration Number

Bid Capacity ( 2AN-B)

Number of years prescribed for completion of subject project / contract

Value of the work executed in last five Financial years (Financial year wise)

Related documents to be uploaded in eprocurement portal.

B = value at current price level of existing commitment and ongoing works to be completed in the next ‘N’ years. Works on hand to be uploaded and this statement should be submitted duly verified by Chartered Accountant.

Integrity Pact (IP)

Earnest Money Deposit (EMD) details

License: License for execution of Electrical works and other specialized works from the concerned authorities /organizations/bodies.

Documents to be uploaded along with tender

Constitution, legal status along with attested copies of Deeds / Articles and Memorandum of Association, etc., as applicable.

Power of Attorney in case of Pvt. Limited/limited companies

Details of person holding the power of Attorney.

Related Document to be Uploaded in eProcurement Portal. (Original /Attested / Notarized)

Registration with HAL/ Other organization if any.

Copy of PAN card issued by Income tax authority

I.T Returns for past 03 years (Assesment Year)

Related documents to be uploaded in eprocurement portal.

Details of ECS viz.,where payments are to be credited along with the scan copy of Blank Cheque leaf

Blank Cheque leaf to be Uploaded in eProcurement Portal.

ECS Bank details as per Annexure in tender documents , signed and sealed by concerned bank to be Uploaded to eProcurement Portal.

Annual turnover for last Five years

Plant and machinery details for the work.

Proposed work completion schedule in the form of bar- chart.

Bank Balance statement for last three months.

Related documents to be uploaded in eprocurement portal.

Overdraft facilities available with the agencies.

Balance sheet for the last Five years

Related documents to be uploaded in eprocurement portal.

Work on hand

Udertaking Annexure-K

Address for correspondence:

Contact details

Acceptance by party for Scope of work as per BOQ and Tender terms & conditions

DECLARATION

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions (Page 1 to 405) including price bid do hereby accept all the terms and conditions laid down.

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer.

Description

Clearing of Jungle- Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared as per the directions of EIC/OIC.

Cutting of Trees- Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth up to and including 60 cm girth

Cutting of Trees- Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60 cm girth up to and including 120 cm girth

Cutting of Trees- Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 120 cm girth up to and including 240 cm girth

Cutting of Trees- Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Above 240 cm girth

Earth work Excavation (In all Kinds of Soil)- Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge and as per the relevant specifications for earthwork provided in the tender document In all kinds of soil

Earth work Excavation (In Ordinary Rock)-Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge and as per the relevant specifications for earthwork provided in the tender document Ordinary rock

Earth work Excavation (Hard Rock)- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge and as per the relevant specifications for earthwork provided in the tender document Hard rock (blasting prohibited)

Construction of Embankment Using Excavated Earth- Construction of embankment/sub grades/shoulders/median filling with approved materials obtained from roadway excavation/drain excavation/structure excavation with all lifts and leads, transporting to site, spreading, grading, watering to required OMC and preparing the side slopes and compacting to meet requirements of table 300-2,Ref. to Technical specification 301, 305 and 408 of MoRTH SPECIFICATIONS FOR ROADS AND BRIDGE WORKS (5th Revision) and as per the relevant specifications for earthwork provided in the tender document including all roaylties complete as per the directions of EIC/OIC. Filling using Excavated Earth and ordinary rock

Construction of Subgrade and Shoulders with material from Borrow Area- Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits and / or quarries with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2,Ref. to Technical specification 305 and 408 of MoRTH SPECIFICATIONS FOR ROADS AND BRIDGE WORKS (5th Revision) and as per the relevant specifications for earthwork provided in the tender document, including all roaylties complete as per the directions of EIC/OIC.

Cosolidation of Existing Subgrade- Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres and as per the relevant specifications for earthwork provided in the tender document

Granular Sub Base (Grading V)- Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 Unit = cum - By Mix in Place Method -GSB Material (Grading V material) and as per the relevant specifications for GSB provided in the tender document complete as per the directions of EIC/OIC.

Wet Mix Macadam- Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge and as per the relevant specifications for WMM provided in the tender document

Primer Coat- Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means complete as per the relevant specifications for Prime Coat provided in the tender document and as per the directions of EIC/OIC.

Tack Coat (on Granular surfaces)- Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom.- With rapid setting bitumen emulsion - On W.B.M / W.M.M. @ 0.4kg/sqm - complete as per the relevant specifications for Tack Coat provided in the tender document and as per the directions of EIC/OIC.

Tack Coat (on Bituminous surfaces)- Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom.- With rapid setting bitumen emulsion - On bituminous surface @ 0.25kg/sqm - complete as per the relevant specifications for Tack Coat provided in the tender document and as per the directions of EIC/OIC.

Dense Graded Bituminous Macadam (GRADING-II)- Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 percent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT&H specification clause No. 505 complete in all respects.- With VG 40 Bitumen (Minimum Bitumen Content of 4.5%. Any additional bitumen content as per JMF shall not be payable to the contractor. Any reduction in the bitumen content shall be recovered from the contractor) - complete as per the relevant specifications for DBM provided in the tender document and as per the directions of EIC/OIC.

Bituminous Concrete With Polymer Modified Bitumen- Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge - With PMB 76 E 10 Bitumen - (Minimum Bitumen Content of 5,4%. Any additional bitumen content as per JMF shall not be payable to the contractor. Any reduction in the bitumen content shall be recovered from the contractor) - complete as per the relevant specifications for BC with PMB 76 E 10 provided in the tender document and as per the directions of EIC/OIC.

Bituminous Concrete With VG-40- Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge - With VG 40 Bitumen - (Minimum Bitumen Content of 5,4%. Any additional bitumen content as per JMF shall not be payable to the contractor. Any reduction in the bitumen content shall be recovered from the contractor) - complete as per the relevant specifications for BC with VG 40 provided in the tender document and as per the directions of EIC/OIC.

Dry Lean Concrete - Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge and as per the relevant specifications for DLC provided in the tender document.

Cement Concrete Pavement- Construction of unreinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approved grade cement @400 kg per cum, coarse and fine aggregate confirming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, seperation membrane, selant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing - Cement concrete prepared with batch mixing machine.The panel size shall be provided as per the GFC drawings issued by HAL or the Design agency appointed by HAL. (Note : Target Average Flexural Strength at 28 days for Cement Concrete Pavement shall not be less than 4.8 MPa and Characteristic Flexural Strength at 28 days for Cement Concrete Pavement shall not be less than 4.1 MPa) -complete as per direction of Engineer-in- charge and as per the relevant specifications for Cement Concrete Pavement provided in the tender document.

Road Markings- Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint (self priming paint) conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete and as per the directions of EIC/OIC.

Airfield Pavements Markings- Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, including cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete and as per the directions of EIC/OIC.

Disposal of Surplus Earth- Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.

PCR Evlauation- Undertaking PCR evaluation of newly constructed airfield pavements complete as per specifications outlined in FAA AC -150/5370-11B complete as per directions of engineer in charge of work.

Friction Testing- Undertaking Friction Testing of newly constructed airfield pavements complete as per specifications outlined in ICAO Document 9137-Part 1 complete as per directions of engineer in charge of work.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Earth work Excavation (In Ordinary Rock)- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. Ordinary rock

Earth work Excavation (Hard Rock)- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. Hard rock (blasting prohibited)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications - Height upto 5m - RCC Grade M20 using batching plant transit mixer & Concrete pump (including formwork) as per MORTH Specifications for Reinforced concrete works in substructure including neccessary formwork complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level- with TMT bars Fe 500D complete as per the directions of EIC/OIC.

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete - 450 mm dia complete as per the directions of EIC/OIC.

Extra for forming cavity 5 cm to 11.5 cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. ties 300 mm long of 25x3 mm section at not less than 3 ties per sqm as per approved design complete as per the directions of EIC/OIC.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete as per the directions of EIC/OIC.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete complete as per the directions of EIC/OIC.

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos/ Lindane emulsifiable concentrate of 20% complete as per the directions of EIC/OIC.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration complete as per the directions of EIC/OIC.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete as per the directions of EIC/OIC.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement -All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement- All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level with TMT bars Fe 500 complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level with TMT bars Fe 500 D complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for; Weather shade, Chajjas, corbels etc., including edges complete as per the directions of EIC/OIC.

Providing and constructing brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 35 kgf/cm2 , straight or curved on plan to any radius built in Cement Mortar 1:6 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and complete as per the directions of EIC/OIC.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. - Granite stone slab colour black, Cherry/Ruby red - Area of slab over 0.50 sqm complete as per the directions of EIC/OIC.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. complete as per the directions of EIC/OIC. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable -Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).complete as per the directions of EIC/OIC.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete as per the directions of EIC/OIC.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality complete as per the directions of EIC/OIC.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) complete as per the directions of EIC/OIC.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper complete as per the directions of EIC/OIC.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.

Providing and fixing 304 - grade stainless steel hand rails of 14-gauge pipes for Ramps staircase made out of stainless steel hallow pipes, using 50mm dia for verticals @1.60 mtr c/c fixed tot he ramps or steps by drilling with bolts and 100mm dia MS base plates 10mm gauge for fixing of Vertical pipes 4 - Nos anchor bolts & 40mm dia pipes fixed horizontally for 2-rows top, one pipes fixed with vertical pipes another one fixed with elbows and 25mm dia pipes are fixed horizontally for 2-rows below top measure @ equal intervals including cutting, welding, bending wherever necessary with suitable caps @ tops, bottoms & corners finishing with mat / shining etc., complete including cost and conveyance of all materials, labour for all items of work, HOM with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work. Ramps or Staircase for physically challenged.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 120 mm complete as per the directions of EIC/OIC.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete: Hot finished welded type tubes complete as per the directions of EIC/OIC.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.: 80x1.25 mm M.S. laths with 1.25 mm thick top cover complete as per the directions of EIC/OIC.

Providing and fixing ball bearing for rolling shutters complete as per the directions of EIC/OIC.

Extra for providing mechanical device chain and crank operation for operating rolling shutters: Exceeding 10.00 sqm and upto 16.80 sqm in the area complete as per the directions of EIC/OIC.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete as per the directions of EIC/OIC.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Antiskid finish of size. Size of Tile 600 x 600 mm complete as per the directions of EIC/OIC.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. complete as per the directions of EIC/OIC.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion: Coupler 110 mm complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster complete as per the directions of EIC/OIC.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) complete as per the directions of EIC/OIC.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete as per the directions of EIC/OIC.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work complete as per the directions of EIC/OIC.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete as per the directions of EIC/OIC.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete as per the directions of EIC/OIC.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured - complete as per the directions of EIC/OIC.

Providing and fixing G.I. Chain Link fabric fencing of required width in mesh size 50x50 mm inlcuding strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the sirection of Engineer-in-charge Made of GI wire of dia 4 mm complete as per the directions of EIC/OIC.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above up to plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. TMT bars Fe 500 complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. TMT bars Fe 500 D complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers complete as per the directions of EIC/OIC.

Providing and constructing brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 35 kgf/cm2 , straight or curved on plan to any radius built in Cement Mortar 1:6 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and as directed by the EIC.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per the directions of EIC/OIC.

Providing corrugated G.S. sheet roofing (1.00 mm thick with zinc coating not less than 275 gm/m² as per 12.1.1 of CPWD Specification.) including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster complete as per the directions of EIC/OIC.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete as per the directions of EIC/OIC.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.- 1.2 Meter high and 250 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.- 40 m

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required Upto 150 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc complete as per the directions of EIC/OIC.- Concealed Pipework 15 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc complete as per the directions of EIC/OIC.- Concealed Pipework 20 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc complete as per the directions of EIC/OIC.- Concealed Pipework 25 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc complete as per the directions of EIC/OIC.- Concealed Pipework 32 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall- complete as per the directions of EIC/OIC. 20 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall- complete as per the directions of EIC/OIC. 25 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall- complete as per the directions of EIC/OIC. 32 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall- complete as per the directions of EIC/OIC. 40 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall- complete as per the directions of EIC/OIC. 50 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 80 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 100 mm nominal inner dia Pipes

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 100 mm Dia - complete as per the directions of EIC/OIC.

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 100 mm dia- complete as per the directions of EIC/OIC.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required complete as per the directions of EIC/OIC. 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required complete as per the directions of EIC/OIC. 80 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange complete as per the directions of EIC/OIC. 100 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange complete as per the directions of EIC/OIC. 80 mm dia

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as per the directions of EIC/OIC. W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.Pincluding painting of fittings and cutting and making good the walls and floors wherever required complete as per the directions of EIC/OIC. Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete as per the directions of EIC/OIC. White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete as per the directions of EIC/OIC. Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required complete as per the directions of EIC/OIC.- Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan complete as per the directions of EIC/OIC.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete as per the directions of EIC/OIC. - Flexible pipe 32 mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap complete as per the directions of EIC/OIC.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design complete as per the directions of EIC/OIC.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing complete as per the directions of EIC/OIC. Rectangular shape 1500x450 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete as per the directions of EIC/OIC.

Providing and fixing toilet paper holder complete as per the directions of EIC/OIC. C.P. brass

Providing and fixing soil, waste and vent pipe complete as per the directions of EIC/OIC. 100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing soil, waste and vent pipe complete as per the directions of EIC/OIC. 75 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:159059

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes complete as per the directions of EIC/OIC. 75 mm dia pipe

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes complete as per the directions of EIC/OIC. 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc complete as per the directions of EIC/OIC. For 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc complete as per the directions of EIC/OIC. For 75 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete as per the directions of EIC/OIC. 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete as per the directions of EIC/OIC. 75 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing double equal plain junction of required degree complete as per the directions of EIC/OIC.- 100x100x100x100 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing double equal plain junction of required degree complete as per the directions of EIC/OIC.- 75x75x75x75 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree complete as per the directions of EIC/OIC.- 100x100x100 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree complete as per the directions of EIC/OIC.- 75x75x75 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing double unequal plain junction of required degree complete as per the directions of EIC/OIC.- 100x100x75x75 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing single unequal plain junction of required degree complete as per the directions of EIC/OIC.- 100x100x75 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing double equal plain invert branch of required degree complete as per the directions of EIC/OIC.- 100x100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing single equal plain invert branch of required degree complete as per the directions of EIC/OIC.- 100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing single equal plain invert branch of required degree complete as per the directions of EIC/OIC.- 75x75x75 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single unequal plain invert branch of required degree complete as per the directions of EIC/OIC. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 complete as per the directions of EIC/OIC.- 65 mm offsets With 100 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 complete as per the directions of EIC/OIC.- 65 mm offsets With 75 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 complete as per the directions of EIC/OIC.- 130 mm off sets With 100 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 complete as per the directions of EIC/OIC.- 130 mm off sets With 75 mm dia pipe

Providing and fixing terminal guard complete as per the directions of EIC/OIC.- 100 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe complete as per the directions of EIC/OIC.- 100 mm dia SS 304 grade coupling with EPDM rubber gasket

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe complete as per the directions of EIC/OIC.- 75 mm dia SS 304 grade coupling with EPDM rubber gasket

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter complete as per the directions of EIC/OIC.- 100 mm

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter complete as per the directions of EIC/OIC.- 75 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors complete as per the directions of EIC/OIC.- 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors complete as per the directions of EIC/OIC.- 75 mm inlet and 75 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms complete as per the directions of EIC/OIC.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms complete as per the directions of EIC/OIC.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour complete as per the directions of EIC/OIC. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe complete as per the directions of EIC/OIC. Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe)

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe complete as per the directions of EIC/OIC. Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe complete as per the directions of EIC/OIC. Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, includingcutting and making good the walls and floors wherever required complete as per the directions of EIC/OIC. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete as per the directions of EIC/OIC.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete complete as per the directions of EIC/OIC.

Constructing soak pit 1.20x1.20x1.20 m filled with brick bats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Providing and constructing brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 35 kgf/cm2 , straight or curved on plan to any radius built in Cement Mortar 1:6 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and as directed by the EIC.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level: Cement mortar 1:4 (1 cement : 4 coarse sand) complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level - Fe 500 D complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster complete as per the directions of EIC/OIC.

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars as per the directions of EIC/OIC.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead as per the directions of EIC/OIC.

Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of Engineer-in-charge

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. - Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of Soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. TMT bars Fe 500 D complete as per directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level - s Fe 500 D complete as per directions of EIC/OIC.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete as per the directions of EIC/OIC.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete complete as per the directions of EIC/OIC.

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos/ Lindane emulsifiable concentrate of 20% complete as per the directions of EIC/OIC.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration complete as per the directions of EIC/OIC.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete as per the directions of EIC/OIC.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) complete as per the directions of EIC/OIC.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement- All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement- All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level with TMT bars Fe 500 complete as per the directions of EIC/OIC.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level with TMT bars Fe 500 D complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers complete as per the directions of EIC/OIC.

Centering and shuttering including strutting, propping etc. and removal of form for; Stairs, (excluding landings) except spiral-staircases, including edges complete as per the directions of EIC/OIC.

Providing and constructing brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 35 kgf/cm2 , straight or curved on plan to any radius built in Cement Mortar 1:6 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and complete as per the directions of EIC/OIC.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings complete as per the directions of EIC/OIC.. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. - Granite stone slab colour black, Cherry/Ruby red - Area of slab over 0.50 sqm complete as per the directions of EIC/OIC.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. complete as per the directions of EIC/OIC. Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement- All works above plinth level upto floor V level Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).complete as per the directions of EIC/OIC.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete as per the directions of EIC/OIC.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality complete as per the directions of EIC/OIC.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) complete as per the directions of EIC/OIC.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm complete as per the directions of EIC/OIC.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper complete as per the directions of EIC/OIC.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.

Providing and fixing Toilet cubicals with the following specifications Thickness of Compact Laminate : 18 mm Color of HPL Boards: As approved by Engineer-in-charge Size of Cubicle : As per drawing Door Size : 1995mm (H) x 610mm (W) Divider Size : 1995mm (H) Overall Height Of Cubicle : 2100mm (Including boom Gap of 100mm) Accessories: Standard - Merino Make Stainless Steel - 304 Grade accessories) a) SS "U" Channel b) SS "F" channel c) SS Coat Hook d) SS Privacy Thumb turn c/w Occupancy Indicator e) SS Door Knob f) SS Hinges with Cover g) SS Shoe Box Leg 18mm - 316 Grade h) Rubber Lining for Groove i) S.S.Screws 304 G & P .V.C Wall Plugs

Providing and fixing 304 - grade stainless steel hand rails of 14-gauge pipes for Ramps staircase made out of stainless steel hallow pipes, using 50mm dia for verticals @1.60 mtr c/c fixed tot he ramps or steps by drilling with bolts and 100mm dia MS base plates 10mm gauge for fixing of Vertical pipes 4 - Nos anchor bolts & 40mm dia pipes fixed horizontally for 2-rows top, one pipes fixed with vertical pipes another one fixed with elbows and 25mm dia pipes are fixed horizontally for 2-rows below top measure @ equal intervals including cutting, welding, bending wherever necessary with suitable caps @ tops, bottoms & corners finishing with mat / shining etc., complete including cost and conveyance of all materials, labour for all items of work, HOM with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work. Ramps or Staircase for physically challenged.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete: Hot finished welded type tubes complete as per the directions of EIC/OIC.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 120 mm complete as per the directions of EIC/OIC.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete as per the directions of EIC/OIC.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Antiskid finish of size. Size of Tile 600 x 600 mm complete as per the directions of EIC/OIC.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying otiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size. Size of Tile 600 x 600 mm complete as per the directions of EIC/OIC.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing. Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent complete as per the directions of EIC/OIC.

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mmx 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product -300 mm Finished Floor Height (FFH) complete as per the directions of EIC/OIC.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). complete as per the directions of EIC/OIC. (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.- 100 mm dia complete as per the directions of EIC/OIC.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion: Coupler 110 mm complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete as per the directions of EIC/OIC.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams complete as per the directions of EIC/OIC.

DOUBLE SKIN ALUMINUM ROOF SYSTEM: Supply and fixing of secret fix standing seam roofing system in 0.9mm thick AA 3004/3005 aluminum alloy. The general roof-construction shall comprise from bottom to top: Top layer – Secret Fix standing seam 65/400 Straight profile sheeting manufactured from aluminium alloy AA 3004/3005 H46 (AlMn1Mg1) as specified in BS EN 1396: 2015 minimum material thickness of 0.9 mm and in finish of PVDF consisting of anti corrosive primer of 5 microns, topcoat of PVDF in 20 +/-2 microns with the Total coating thickness as 25 Microns. The coil for the top panel shall have 75 microns transparent protective guard film with the roofing manufacture name printed, This Guard film prevents scratches during roll forming & handling. The material properties shall be as follows: Ultimate tensile strength minimum 200 N/mm2, 0.2% Proof Stress: min 185 N/mm2, Sheets are to be laid to meet the requirements of the building geometry and fixed on aluminum clips. Clip to be fixed with SS 304 screws only. Second Layer – ST Clip - The standing seam sheet panel of approved make shall be fixed on to the purlin using aluminium ST clips. The head of clips shall be fixed accurately to ensure the roof sheeting expands and contracts freely during thermal movement. The roofing system manufacturer shall submit the below valid 1- British Board of Agreement Certificate 2- 2- the Institute of Bautechnic Zulassungbeschield N R -14.1 .181. 3- Factory Mutual certificate in India. The rate shall include all accessories for the welding, expansion joint, nut bolts & panels. (The erection / fixing /installation shall be done by specialized / authorized agency as per approved list. The installation team shall be fully trained and approved by the manufacturer. The roofing shall be installed only by approved installers recommended by Kalzip only. The work is required to be executed complete as per the directions of EIC/OIC.

Aluminium Flashing Flashings manufactured from aluminium alloy AA 3004/3005 (AlMn1Mg1) as specified in BS EN 1396: 2015 material thickness of 0.9 mm & same finish as panel. Flashing maximum girth to be up to 578m. The work is required to be executed complete as per the directions of EIC/OIC.

Single Skin 2mm thk Alu Gutter: Supply and fixing of Single skin 2mm Aluminium gutter, grade AA1100/1200 or equivalent alloy in mill finish with epdm expansion joints for every 8/12m length, down take spout dia 150mm at every 10m gutter length, & other accessories and welding at joints. The girth of gutter would be maximum 1200mm. The work is required to be executed complete as per the directions of EIC/OIC.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. The work is required to be executed complete as per the directions of EIC/OIC.

Walkways System: Supply and fixing of KALZIP WALKWAYS SYSTEM. The system specification of Walkways is as mentioned below: i) FRP Gratings - FRP Pultruded Grating is made up of a mixture of Resin, Roving, woven matt, Pigment, surface veil etc. It consists of 'I' Section 38 mm Height with Bearing Bar C/c 40mm & Cross Bar of 12mm Dia Round Bar C/c 150mm. It is manufactured From Isopthalic resin. The FRP gratings fulfil the load and deflection conditions as per EN-516. Width of Walkways – 500mm Walkways System Accessories: Kalzip Seam clip made of Aluminium Alloy 6063/T5 Temper mill finished and will be as per BS EN 755- 2 specifications ii) Aluminium L-Angle of thickness 4mm thick made of Aluminium Alloy 6063/T6 Temper mill finished and will be as per BS EN 755-2 specifications. iii) Fasteners used are of Stainless Steel Grade 304. Steel support structure of 500 mm width above the skylight as per requirement shall be provided by the Steel fabricator to support the walkway system Make - Kalzip / Latchways. The work is required to be executed complete as per the directions of EIC/OIC.

Roof Hatch: Providing & fixing Roof Hatch – Single leaf on the standing seam roofing sheet for roof access as approved by Standing Seam Roof manufacturer 914x914 mm. Hatch shall be double walled, external thickness of 2.5mm aluminium sheet and internal 1.2mm aluminium sheet. Internal space of hatch shall be insulated with 50mm thick & 60Kg/m3 rockwool. Latches & lift off handle shall be stainless steel and shall be hydraulic assisted lift operated. Latch hood should have permanently fixed EPDM washer to keep it weather tight. The work is required to be executed complete as per the directions of EIC/OIC.

Fall Arrest Systems: Supply & Installation of Latchways Constant Force Post System as per EN 795 Class C:2012. -1762 Constant Force Post system will be capable of taking load of 3 users. Systems Type & Length- Latchways Constant Force Post System- on 400 mm roof sheets. Systems Certification- EN 795 Class C and ATEX Approved. Testing has been done with 300Kgs weights to prove CFP’s compliance for 3 simultaneous users should include 1000 hours of corrosion testing in Acetic acid Salt spray test to worthiness for minimum 5 years. Material- SS 316 Marine grade, 17/4 pH stainless steel for Cast components and 5084 treated aluminium alloys. Latchways CFP absorbs 4,500 Joules of ensuring that it can take a maximum load of 3 users simultaneously. All CFP systems have omni-directional performance ensuring that load can be taken in 360 degrees rather than just in the direction of wire. Product marking complies to EN 795 and EN 365. CE certificate mark and EC declaration of conformation. Make Latchways. The work is required to be executed complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster complete as per the directions of EIC/OIC.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster complete as per the directions of EIC/OIC.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) complete as per the directions of EIC/OIC.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete as per the directions of EIC/OIC.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work complete as per the directions of EIC/OIC.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete as per the directions of EIC/OIC.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete as per the directions of EIC/OIC.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion , Powder coated aluminium (minimum thickness of powder coating 50 micron) complete as per the directions of EIC/OIC.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width complete as per the directions of EIC/OIC.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) complete as per the directions of EIC/OIC.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured - complete as per the directions of EIC/OIC.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. complete as per the directions of EIC/OIC.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. complete as per the directions of EIC/OIC.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour forfabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structuraland functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all th performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any otheraccreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml Complete as per the directions of EIC/OIC.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. Complete as per the directions of EIC/OIC.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and Complete as per the directions of EIC/OIC.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6SWG dia G.I wire on surface or in recess for loop earthing as required.

Providing and fixing M.V. danger notice plate of 200 mm x 150 mm made of mild steel, at least 2 mm thick , and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick G I Plate with inscription there on , bolted / welded to 35 mm x 35 mm x 6 mm angle iron , 60 cm long & fixing the same in ground as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 x 6 sq mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 x 35 sq mm (32 mm)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation inclucing excavation, sand cushioning, protective covering and refilling the trench etc. as required. Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm

Feeder Pillar (Peripheral Lights) - Supply, installation, testing and commissioning of cubicle type feeder pillar (out -door type) suitable for 440 Volts 3 phase 4 wire 50 Hz AC Supply system fabricated in design from CRCA sheet steel 2 mm thick for frame work and covers 3 mm thick for gland plates including cleaning & finishing complete with 7 tank process for powder coating in approved shade having 100 Amps insulated bus bar with shrounds aluminium alloy bus bars, bottom base channel of MS section not less than 100 mm x 50mmx5 mm thick complete with earth stud the control wiring shall be with 2.5 sq. mm PVCinsulated copper conductor single core cable complete with cable alloys, cable gland plates in two half including providing following switch gears. (a) Incomer (i) 40 Amp 4P MCB -10KA 1 no. (b) Outgoing (i) 6 Amps DP MCB 10KA- 7 nos.

Supply, installation, testing and commissioning of 35 watt LED street light fitting IP 66/65 suitable for installation on 3 mtr high existing pole complete with control gear with extruded aluminium painted housing, integrated IP lens etc as required. (Makes - Philips, Havells, Wipro)

Supply, Installation, testing & commissioning of 3 m high (clear height) galvanised octagonal pole with single arm including foundation bolts having bottom of 130 mm dia, top 70 mm dia on provided foundation. The column shall be provided integral service connection box consisting 1 Nos. 6 Amp SPMCB, Neutral link and 32 Amp heavy dulty brass connector and suitable size 6mm thick backelite plate. The poles should have internal pole box with cover complete as per secifications as required.

Supply of ISI marked aluminium conductor XLPE insulated cable as per IS 7098 (Part - 1) with latest amendment armored secured Sheathed 1100 volts grade as required. 3.5X35sq.mm

Supply of ISI marked aluminium conductor XLPE insulated cable as per IS 7098 (Part - 1) with latest amendment armored secured Sheathed 1100 volts grade as required. 2X6sq.mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Wiring for light/power plug with 2 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit alongwith 1 No 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/power plug with 4 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit alongwith 2 No 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. (AC)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 x 6 sq.mm + 1 x 6 sq.mm earth wire

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 x 6 sq.mm + 2 x 6 sq.mm. earth wire

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 x 10 sq.mm. + 2 x 6 sq.mm. earth wire

Suplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20mm

Suplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying & fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess as required. 1 or 2 Module (75 mm X 75 mm)

Supplying and Fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. For TV antenna socket outlet

Supplying and drawing co-axial TV cable RG-6 garde, 0.7 mm solid copper conductor PE insulated, shieled with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing 25mm dai MS flexible pipe with PVC coating along with accessories like coupler etc. as required

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as require

Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copperbusbar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way ( 4 + 12), Double door

Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copperbusbar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way ( 4 + 18), Double door

Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copperbusbar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way ( 4 + 24), Double door

Supplying and fixing of following ways surface/recess mounting, vertical type, 415V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200A, tinted coppe busbar, common neutral link, earth bar, din bar for mounting MCBs (But without MCB and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way ( 4 + 12), Double door

Supplying and Fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including aerthing etc. as required. (But without MCB/RCCB/Isolator) 8 way, Double door

Supplying and Fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including aerthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Tripple pole neutral

Supplying and fixing following rating, double pole, (single phasenand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

Supplying and fixing following rating, double pole, (single phasenand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, double pole, (single phasenand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying & fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut,bolt,spring,washer excavation and re-filling etc. as required.

Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut , bolt , spring , washer excavation and re-filling etc. as required.

Providing and fixing 25 mm x 5 mm copper. strip on surface or in recess for connections etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and Fixing of lightning conductor finial, made of 25mm dia 300mm long, G.I Tube, having single prongat top, with 85mm dia 6mm thick G.I Base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/sweating and soldering etc as required.

Providing and fixing GI tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing GI tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring/cable as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated & PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering & refilling the trench etc. as required. Upto 35 sq. mm

Laying of one number additional PVC insulated & PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering & refilling the trench etc. as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of following sizes in the existing masonry duct Upto 35 sq. mm

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of following sizes in the existing masonry duct Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of following sizes in the existing masonry duct Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sq. mm (19mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (32mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm (70mm)

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Providing & Fixing of Circular / hexagonal MS sheet box for ceiling fan clamp of internal dia. 140 mm, 73 mm height , top lid of 1.5 mm thick of MS sheet with its top surface hacked for proper bonding, top lid shall be screwed to the MS sheet box by mens of 3.3 mm dia. round headed screws one lock at the corners. Clamps shall be made of 12 mm dia. MS bar bent to shape as per standard drawing

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100A

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply, Installation, testing & Commissioning of MAIN L.T. Panel as per IS/IEC 61439-2 and descibe below with Type-1 & Type-2 Surge protection device (SPD) as per NBC-2016 guidelines, as per the standard technical specification and as per the directions of engineer incharge of work.

Supply, installation, testing & commissioning of Capacitor Panel (165kVAr) as described below, as per the standard technical specification, Single Line Diagram and as per the directions of engineer incharge of work.

Supply, installation, testing & commissioning of MDB Panel - as described below, as per the standard technical specification and as per the directions of engineer incharge of work.

Supply and fixing in position the approved “Shock Treatment Charts” written in English and Local Language. These charts shall be framed in teak wood frame and covered with glass, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply and fixing in position the fire extinguishers carbon-di-oxide type 2.5 Kgs capacity, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply and fixing in position the best quality Danger Boards of approved shape and size as specified by Local Electricity Authorities written in English & Local Languages, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply and fixing in position 1000 mm wide insulation mats made of elastomer of 11 KV grade as IS-15652-2006. Thickness of rubber mat shall be not less than 3 mm, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of fire buckets 6 nos. in each set duly filled with fine sand and fixed on an angle iron frame as per requirement of local authorities. Fire buckets shall be painted red from outside and white from inside with additional handle at the bottom, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size glass frame in the sub station, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of first aid box of approved make, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of tool kit with 1 pair 11KV rubber hand gloves of approved make, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of tool kit with 1 pair 415 volts rubber hand gloves of approved make, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of 2kg capacity FK-5-1-12 with UL approved non ferrous Seamless Cylinder, DLP Assembly with automatic valve, push in connector for tube, UL approved 2 Kilogram FK-5-1-12 Gas ref NFPA 2001 FK-5-1-12 , mounting bracket, End of Line adopter & Pressure guage ,UL approved low pressure switch for monitoring system activation. b) 4 KG

Supply of 2kg capacity FK-5-1-12 with UL approved non ferrous Seamless Cylinder, DLP Assembly with automatic valve, push in connector for tube, UL approved 2 Kilogram FK-5-1-12 Gas ref NFPA 2001 FK-5-1-12 , mounting bracket, End of Line adopter & Pressure guage ,UL approved low pressure switch for monitoring system activation. b) 2 KG

Supply & Fixing of Linear pneumatic heat Detection Tube :- UL Listed Heat detection Tube, 4mm ID, 6mm OD, detection temprature less than 175 Deg celcius, mutlilayer, Water Absorbtion ≤ 1.5% @ 20oC and 50% RH as tested per ISO62 with fittings and supports

Supply of Control Unit for controlling each system, complete with pressure switches, buzzers and electronic hooters, including all necessary accessories eletrical wiring to make each entire system functional.

Installation Testing & Commissioning of Tube based fire suppression system for electrical panels

Supply and fixing in position 1000 mm wide rubber matting of 1100 volts grade as per electricity rules (exact length of rubber mat to be worked out as per site requirement). Thickness of rubber mat shall be not less than 6 mm, as per the standrad technical specification and as per the directions of engineer incharge of work.

Supplying, of following 1100 volt grade XLPE/ PVC insulated copper conductor armoured/unarmoured cables (Control cable for LT panel, DG and Transformer etc.) . Laying in existing trenches/ cable trays/ ducts/ clamped to wall with suitable clamps, including thimble, end termination, gland, bimettalic crimping lugs, fixing bolts, to complte the system as per the directions of engineer incharge of work. 4 C x 2.5 sq.mm

Supplying, of following 1100 volt grade XLPE/ PVC insulated copper conductor armoured/unarmoured cables (Control cable for LT panel, DG and Transformer etc.) . Laying in existing trenches/ cable trays/ ducts/ clamped to wall with suitable clamps, including thimble, end termination, gland, bimettalic crimping lugs, fixing bolts, to complte the system as per the directions of engineer incharge of work. 7 C x 2.5 sq.mm

Supplying, of following 1100 volt grade XLPE/ PVC insulated copper conductor armoured/unarmoured cables (Control cable for LT panel, DG and Transformer etc.) . Laying in existing trenches/ cable trays/ ducts/ clamped to wall with suitable clamps, including thimble, end termination, gland, bimettalic crimping lugs, fixing bolts, to complte the system as per the directions of engineer incharge of work. 12 C x 2.5 sq.mm

Supply, Installation, Testing & commissioning of 40 W surface / suspended linear 4ft LED luminaire, Housing Extruded Aluminium, Efficacy >=100lm/w, having a system level lumen package of 4000 lumens and IP 40 protection,driver etc. complete in all respect as required.

Supply, installation, testing and commissioning of 20W LED batten 2' long with high end diffuser for uniform distribution of light complete with electronic driver & accessories as required (Mirror light) as per the standard technical specification and as per the directions of engineer incharge of work.

Supply, Installation, Testing & commissioning of Pressure Diecast LED Bulkhead 10W (>=700lumens) with Efficiency 70lm/w Bulk head luminaire for interior & exterior use, complete in all respect as required.

Supply, Installation, Testing & commissioning of Pressure diecast Aluminium housing Surface Mounted Light suitable for 18W(>=1567 Lumen Output) LED Downlight complete in all respect as required.

Supply, installation, testing and commissioning of 15W LED Down light with electronic driver & accessories as required as per the standard technical specification and as per the directions of engineer incharge of work.

Supply, Installation, Testing & commissioning of Surface/Recessed 2' X2' LED luminaire, Housing CRCA, Efficacy >=100lm/w having a minimum system level lumen package of 3600 lumens ,IP 20 protection,isolated driver etc. complete in all respect as required.

Supply, Installation, Testing & commissioning of Surface / suspended Mounted Light suitable for 80W with 10400Lm LED highbay complete in all respect as required.

Supply, installation, testing & commissioning of Self contained drinking water cooler with energy efficient hermetically sealed reciprocating compressor, R-134a Refrigerant with full body stainless steel 304 grade model, cooling capacity 40 Ltrs./Hr., Storage capacity 40 Ltrs., brass chrome plated single faucets, single sheet moulded drain to prevent water spillage and suitable for operation on 230 volt ± 10%, 50Hz, single phase AC supply, connectrions with existing water source, including one year warranty & maintenance, etc. complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply, installation, testing & commissioning of water purifier unit of purification capacity up to 50 Ltrs./Hr. having feature of RO+UV+UF treatment, TDS controller, maintaining essential minral contents in the purified water, suitable for operation on 230 volt ± 10%, 50Hz, single phase AC supply along with suitable arrangement for fixing with existing water coolers. Including one year warranty & maintenance, etc. complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply, installation, testing & commissioning of wall mounted fully automatic stainless steel 304 grade model Hand dryer suitable for hevy traffic load, energy efficient motor operating volatge 230 volt ± 10%, 50Hz, single phase AC supply, Auto Cutoff in 30 Seconds, water splash proof IPX1, noise level <80Db, Including one year warranty etc., complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Supplying of following 1.1 KV grade aluminium conductor extruded XLPE insulated PVC innersheath,GI wire/tape armoured specified and outer PVC sheathed cable of following specifications and sizes as per IS 7098 (Part I) as required. 2 core 10 sqmm

Supplying of following 1.1 KV grade aluminium conductor extruded XLPE insulated PVC innersheath,GI wire/tape armoured specified and outer PVC sheathed cable of following specifications and sizes as per IS 7098 (Part I) as required. 4 core 16 sqmm

Supplying of following 1.1 KV grade aluminium conductor extruded XLPE insulated PVC innersheath,GI wire/tape armoured specified and outer PVC sheathed cable of following specifications and sizes as per IS 7098 (Part I) as required. 3.5 core 35 sqmm

Supplying of following 1.1 KV grade aluminium conductor extruded XLPE insulated PVC innersheath,GI wire/tape armoured specified and outer PVC sheathed cable of following specifications and sizes as per IS 7098 (Part I) as required. 3.5 core 185 sqmm

Supplying of following 1.1 KV grade aluminium conductor extruded XLPE insulated PVC innersheath,GI wire/tape armoured specified and outer PVC sheathed cable of following specifications and sizes as per IS 7098 (Part I) as required. 3.5 core 300 sqmm

Supplying, installing, testing and commissioning of 400KVA Diesel Generator set with following specifications. Power rating as per standard reference condition as per-BS 5514 / ISO 3046 / ISO 8528 & IS 1002 / ISO 3046 Generator set specifications.

HT Cable: Supplying of 3Cx240sqmm high tension 11KV cable, Dry Curing & Dry Cooling with true triple extrusion, simultaneously through a single common head, 3 core under ground XLPE (E) cable having stranded compact circular aluminium conductor, screened insulated, insulation screened with extruded semiconducting compound in combination with copper tape, core laid up extruded inner sheathed of GI flat strip armoured and overall PVC sheathed with specified IS 7098/11/85 with latest amendments.

Supply, erection, testing and commissioning of 400 KVA KVA 5Star rated Copper wound Distribution Transformer 11KV/433V with Off Load Tap Switch, Buchholtz relay winding temperature indicator, oil temperature indicator, marshalling box with wiring, oil level indicator with + 5% to -10% Steps of 2.5%, HT & LT Cable Entry Box a Type, stacked core with oil as per IS:1180 (Part-1):2014 with all standard accessories as per latest IS standard No: 2026/1977 and IS:335 and as per technical specification.

Supplying of following size of single phase 240 V A.C 380mm metalic Exhaust fan heavy duty complete with motor, blade frames with louvers as required.

Supply, Installation, Testing & Commissioning of armoured 6 core Singlemode OS2 (9/125 Micro), Corrugated ECCS Armor, HDPE (UV) Sheathing, Theoxtropic gel filled OFC cable with 2 Nos steel music wire embedded in side sheathing as stregth member for switch connectivity. Cable should be ROHS compliant and as per IEC60749-1 with product warranty of 30 years.

Supply, Installation, Testing & Commissioning of 6F SM loaded LIU with LC adaptor plates, pigtel cables, Spilce tray, cable holder and 4 nos of cable entry exist point with rubber gurment along with the LIU, Powder Coaded 1.2mm steel sheet metal, 1U etc complete as required. LIU should be in accordance with YD/T 778-2006 Optical Distribution Frame & YD/T 1272.1-2003 Optical Fiber Connector Part 1: Type LC and should have 30 years of product warranty.

Supply, Installation, Testing & Commissioning of 24F SM loaded LIU with LC adaptor plates, pigtel cables, Spilce tray, cable holder and 4 nos of cable entry exist point with rubber gurment along with the LIU, Powder Coaded 1.2mm steel sheet metal, 1U etc complete as required. LIU should be in accordance with YD/T 778-2006 Optical Distribution Frame & YD/T 1272.1-2003 Optical Fiber Connector Part 1: Type LC and should have 30 years of product warranty.

Supply, Installation, Testing & Commissioning of LC-LC singlemode OS2 (9/125) duplex, LSZH fiber patch cord for LIU to switch connectivity. Patch Cord should have aramid yarn as strenght member with 1000 time mating cycle.

Supply, Installation, Testing & Commissioning of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color

Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.

Supply, installation, testing & commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, Installation, Testing & Commissioning of 18U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of Pure IP at core server Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility ,10 IP users License ,01 Nos. IP Operator Console, 100 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, TEC should be with GR Number, - Should Support Redundant server in active-Active mode.

Supply, Installation, Testing & Commissioning of Type 1 IP Phone 1 VoIP account , Full duplex speaker phone, IPV6, 2xLAN, PoE .

Supply, Installation, Testing & Commissioning of access switch 24 x 1G and 6 x 1/10GSFP+ ports. PoE+ switch with min 370 Watt PoE+ budget .Should have RPS option from day 1. Should support 10 Gbps Copper module on SFP+ port for flexibility to utilize. Switching capacity of 168 Gbps, forwarding performance 124 Mpps, should have non-blocking architecture, 16K MAC address. Should have Static Routing, RIP, VRRP, OSPF, OSPFv3, BGP,BGP4+,MPLS from day 1, Should support ISSU from day 1, Should support stacking with min 14 members in a stack, Neighbour discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), IPv6 features from day 1, MTBF Min 198000 Hr.

Supply, Installation, Testing & Commissioning of 8 Port POE+ Access Switches with switching capaticy of 96 Gbps, forwarding performance 71 Mpps, having 8 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 125W, with 4 x 10G SFP+ uplink ports. Should Non Blocking architecture , 16K MAC address. Should have Static Routing ,RIP,VRRP, OSPF from day 1,Should support ISSU from day 1 ,Should support stacking with min 12 members in a stack, Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), IPv6 features from day 1 , MTBF Min 198000 Hr

Supply, installation, testing & commissioning of fiber Modules 1000BASE

Supply, installation, testing & commissioning of fiber Modules 10G BASE

Supply, Installation, Testing & Commissioning of 4x4 Access Point Ceiling Mount having 1 x 2.5GE (PoE/PoE+) port , 1 x G Copper port .For 2.4G 2*2 MIMO, For 5G 4*4 MIMO .Built-in omnidirectional internal antennas, Dual frequency with min 6 Stream .For 2.4G: 3dBi and for 5G: 3dBi.200 square meter coverage (without any obstacle).Maximum number of users per band should be minimum 128. power consumption:18W. Encryption: AES, WPA3\802.11i: Supported, Authentication: MAC Address/PSK, Client isolation: Both Layer-2 wireless client isolation and SSID isolation, forwarding security: Packet filter, MAC address filter, and broadcast storm suppression, SSID-VLAN binding: Supported, Management frame protection (802.11w): Supported. Should be CE, FCC, CCC, ROHS certified. Access Points should have option to be managed by cloud infrastructure without replacing the hardware in future required

Supply, installation, testing & commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : Customer Flow staistics, Cross COunt, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , In built IR LED , IR Distance upto 45 meters , IP 66 ,IK10,POE.Audio -1 input/1 output

Supply, installation, testing & commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+/MJPEG .SD card support up to 256Gb, Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : Customer Flow staisticsCross Count, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , IR Distance upto 45 meters , IP 66 , POE. Audio -1 input/1 output

Supply, installation, testing & commissioning of L2+ managed industrial PoE switch with 24*10/100/1000M RJ45 ports and 4*1/10G SFP+ fiber slot ports, Port 1-24 can support IEEE 802.3af/at PoE standard, switching capaticy of 598 Gbps, forwarding performance 95.23 Mpps, maximum PoE output power is 400W(at-600W), with 32K MAC address. Should have Static Routing , system logging, Telnet, SSH2.0, SNMP V1/V2C/V3, Network Time Protocol (NTP), FTP, TFTP, Xmodem.

Supply, installation, testing and commissioning of 16 channel NVR , ONVIF compliant , CE,FCC,UL, &BIS Certification, recording bandwidth 320 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ-45 port (1000M) , Bit Rate 16kbps-20mbps per channel, Sync Playback 4/8/10/16 ch playback, iOS smartphone support , 2 HDD support , each HDD slot support upto 8 TB HDD , , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse, Display resolution up to 4K, 1 E-Sata Port, RS-485 Port, Cloud Storage, Net HDD, Edge analytics : Customer Flow staistics, Face Attendence, Face Detection and Recognition, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection, Queue length detection, Regional population statistics, SOD-Stationary Object Detection, Deterrence, PIR, AI Registerd Qty- 10000 & AI Captured Qty- 200000. Protocol support:- HTTP, HTTPS TCP/IP, IPv4, UPNP, RTSP,UDP,SMTP,NTP,DHCP,DNS,IP filter,PPPOE,DDNS,FTP,IP search, P2P, NFS/SMB/CIFS, IPC Management.

Supply, Installation, Testing & Commissioning of 16TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG LSZH as per ANSI/TIA 568 C.2 and ISO/ IEC 11801–2nd Edition, ROHS Compliant, solid copper conductors, tested @250 Mhz, with HDPE insulation of individual conductor and over all Dia of 5.8mm for Connectivity of Hub room to End Point.

Supply, Installation, Testing & Commissioning of CAT 6 UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Camera at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6 cable termination at rack end.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, installation, testing & commissioning of Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. UL268, 7th Edition & FM Approved.

Supply, installation, testing & commissioning of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches UL268, 7th Edition & FM Approved.

Supply, installation, testing & commissioning of Response Indicator ( RI) High visibility LED, Wide viewing angle for increased visibility, Discreet design for incorporation in to any décor. RI should be of same make as detectors & devices.

Supply, installation, testing & commissioning of Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device UL & FM Approved.

Supply, installation, testing & commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance UL & FM Approved.

Supply, installation, testing & commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installation, testing & commissioning of Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL & FM Approved.

Supply, installation, testing & commissioning of Network Repeater Panel with minimum 10" Color Touch Screen display with QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation UL & FM Approved.

Supply, installation, testing & commissioning of Addressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center. UL Listed.

Supply, installation, testing & commissioning of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supply, Installation, Testing and Commissioning of Fire Exit Sign and Internal Hydrant illuminated sign made from etched sheep with 5W LED illumination and all electrical accessories including battery and battery charger etc. complete as required as per Standard technical Specification and as per the directions of Engineer incharge of work.

Supply, Installation, Testing & Commssioning of 8 Channel & 8 Zones IP based digital Voice Alarm controller capable of handling 4000 Watts. The voice alarm controller should be able to connect directly over Ethernet. It should have functions like the audio playing, zone control, fault monitoring, log recording, volume control and amplifier switchover. The System shall be expandable type upto 2000 Zones. Individual Voice alarm controller should also have the following functions: . 255 Priorities . Time schedule broadcasts . 2 additional Channels for back up Amplifiers. . 8 trigger inputs/outputs . 8 AVC dgital input. . 5 Addressable Noise detectors per speaker zone. (Note: master slave/Master router controller concept not accepted to avoid single point failure).

Supply, Installation, Testing & Commssioning of 1X500W Class-D Amplifier, which can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection and High Efficiency Class D Power Amplifier, 500W, 100V/70 Output, with 100 - 240 VAC input and 24 VDC backup power Supply.

Supply, Installation, Testing & Commssioning of 6W Ceiling Speaker with max SPL1M/1W 95dB . Frequency response of 125Hz-16KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W.

Supply, Installation, Testing & Commssioning of 6W Wall mount Speaker with max SPL1M/1W 95dB . Frequency response of 125Hz-16KHz. The speaker shoud have tappings at 6W/3W.

Supplying, erecting, testing and commissioning of 220/250 Volts, single phase, 0.5 HP, 6000 RPM, 50 Hz Siren of 3.25 km range (Diametrical), horizontal double mounting type with metal elastic anti vibration rubber mounting pad on complete C.C. foundation (1:2:4) with plastering of size 60 x 60 x 20 cm for Siren motor with nut bolts of required size with 1.2 cm thick hard rubber sheet packing provided in between the foundation and motor base to minimise the jerks and vibration to the slab complete.

Supply, Installation, Testing and Commissioning of microprocessor based UPS system of 15 kVA rating at 0.9 pf true online UPS using PWM IGBT technology. 3-phase input 415V and input frequency 50 Hz, 3-phase out put fixed setting at 380, 415 and 430V with 30 min. battery backup as specified in technical specification as required and as specified as per technical specification.

Supply, installation, testing and commissioning of 35 watt LED street light fitting IP 66/65 suitable for installation on 3 mtr high existing pole complete with control gear with extruded aluminium painted housing, integrated IP lens etc as required.

Supply, Installation, testing & commissioning of 3 m high (clear height) galvanised octagonal pole with single arm including foundation bolts having bottom of 130 mm dia, top 70 mm dia on provided foundation. The column shall be provided integral service connection box consisting 1 Nos. 6 Amp SPMCB, Neutral link and 32 Amp heavy dulty brass connector and suitable size 6mm thick backelite plate. The poles should have internal pole box with cover complete as per secifications as required.

and including supplying, fixing and commissioning MCB type change over switch 4 pole, 40A with 3 positions (I-O-II) with centre off position complete in all respects as required

EarthingwithG.l. earthpipe 4.5metre long, 40mmdia including accessories, and providingmasonry enclosure with cover plate having locking arrangement andwateringpipeetc.withcharcoal/cokeandsaltasrequired.

Earthing with G.l. earth plate 600mmX600mmX6mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipeof 2.7metre longetc.withcharcoal/coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing 25mmX5mm G.l. strip on surface or In recess for connection set asrequired.

Layingof onenumberPVC insulatedandPVCsheathed / XLPE powercableof 1.1KVgradeof followingsize intheexistingRCC/HUME/METALpipeasrequired. Upto 35 sq.mm

Layingof onenumberPVC insulatedandPVCsheathed / XLPE powercableof 1.1KVgradeof followingsize intheexistingRCC/HUME/METALpipeasrequired. Above 35sq.mm and upto 95 sq.mm

Layingof onenumberPVC insulatedandPVCsheathed / XLPE powercableof 1.1KVgradeof followingsize intheexistingRCC/HUME/METALpipeasrequired. Above185sq.mm and upto 400 sq.mm

Laying and fixing of one number PVC insulated and PVCsheathed / XLPE power cable of 1.1KV grade of following size on cable tray as required. Above 35sq.mm and upto 95 sq.mm (clampedwith25x3mmMS Metre flatclamp)

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as requiredin layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements anddisposal of unserviceable material as directed, within a lead of 50 m: Pipes, cables etc. not exceeding 80 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 X 16 sq. mm (25mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2X16sq.mm(22mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2X35sq.mm(25mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3X50sq.mm(32mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 x300 sqmm(70 mm)

Laying of one number PVC insulated & PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation, sand cushioning, protective covering & refilling the trench etc. as required. Above 185 sqmm and upto 400 sqmm

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of following sizes on cable tray as required. Above 185 sqmm and upto 400 sqmm

Supply of elevated type high intensity bi directional Runway edge light fixture suitable for 150 W halogen lamp on 6.6A AC constant current series system complete with lense / filter, halogen lamp, reflector assembly, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required to meet ICAO/CAR requirements and as specified as per technical specification. clear/clear

Supply of elevated type high intensity bi directional Runway edge light fixture suitable for 150 W halogen lamp on 6.6A AC constant current series system complete with lense / filter, halogen lamp, reflector assembly, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required to meet ICAO/CAR requirements and as specified as per technical specification. Clear/Yellow

Supply of elevated type high intensity bi directional Runway edge light fixture suitable for 150 W halogen lamp on 6.6A AC constant current series system complete with lense / filter, halogen lamp, reflector assembly, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required to meet ICAO/CAR requirements and as specified as per technical specification. Unidirectional red stop way fixtures

Supply of inset type bidirectional high intensity Runway Threshold cum End, green/red light fittings complete with optical assembly suitable for 3 nos.of 105W 6.6 Amp.Halogen lamps including lens holder, lens, clamping mechanism, prefocus lamp holder, halogen lamps, gaskets with suitable shallow base other accessories complete in all respect and in compliance with ICAO, Annex-14 and as specified as per technical specification.

Supply of inset type unidirectional high intensity Runway Threshold green light fittings complete with optical assembly suitable for 2 nos.of 105W 6.6 Amp.Halogen lamps includinglens holder, lens, clamping mechanism, prefocus lamp holder, halogen lamps, gaskets with suitable shallow base other accessories complete in all respect and in compliance with ICAO, Annex-14 and as specified as per technical specification.

Supply of inset type unidirectional high intensity Runway End red light fittings complete with optical assembly suitable for 1 no.of 105W 6.6 Amp.Halogen lamps including lens holder, lens, clamping mechanism, prefocus lamp holder, halogen lamp, gaskets with suitable shallow base other accessories complete in all respect and in compliance with ICAO, Annex-14 and as specified as per technical specification.

Supply of elevated type medium intensity Omni directional taxiway/apron edge light fixture complete with breakable coupling, mounting assembly, base plate, gasket,including LED module (Power consumption not exceeding 8.5W), connecting lead, SS bolts & washers, etc. as required and as per enclosed specifications and complying with ICAO requirements and as specified as per technical specification.

Supply of elevated type medium intensity omni directional turning pad light fixtures suitable for 45 W halogen lamp on 6.6 A AC constant current series system complete with blue lense, halogen lamp, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required and as specified as per technical specification.

Supply of elevated type uni-directional high intensity Approach light fixture suitable for 200W halogen lamp on 6.6A AC constant current series system complete with lens / filter, halogen lamp, reflector assembly, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required as per technical specification.

Supply of inset type uni-directional high intensity Approach light fixture suitable for 200W halogen lamp on 6.6A AC constant current series system complete with lens / filter, halogen lamp, reflector assembly, lamp holder, connecting lead, breakable coupling, base plate and all other accessories etc. as required and as specified as per technical specification.

Supply of inset type bidirectional Runway Edge light fitting (Clear/Yellow)/(Clear/Clear)suitable for 200W halogen lamp on 6.6A AC constant current series system complete with bottom box and all accessories including halogen lamp, Prism , reflector etc. as required and as specified & as per drawing and as specified as per technical specification.

Supply of Guidance Sign Board of various sizes as per ICAO Annex.14 Vol.I (legends as approved by Engineer-in-Charge) made out of anodized 2mm thick Aluminium frame with suitable angle support with 1.5MM thick Al. backcover of 4MM thick polycarbonate sheet with glare free face, the letter and symbol should be made of self adhesive film of 3M applied on the inside face with required colouring suitable arrangement shall be made for water tightness & locking arrangement, signboard shall be uniformly internally illuminated with required numbers of LED lights & drivers to achieve required illumination operated on input source 2.5A to 6.6A constant current including supporting frangible legs & frame etc. complete as required.

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 300W, 20A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 200W, 20A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 150W, 20A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 150W, 6.6A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 100W, 20A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 200W, 6.6A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 15W, 6.6A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 45W, 20A / 6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 100W 6.6A/6.6A

Supply of 5000V, 50 Hz individual lamps series type isolating transformers encapsulated in polyester resin, finally moulded with neoprene rubber as specified in technical specifications of following ratings: 45W 6.6A/6.6A

Supply of copper conductor PVC insulated, PVC sheath single core unarmoured anti termite and anti rodent treated UG cable for unearthed system of 5 KV grade conforming to IS 1554 Pt II as amended upto date and as specified in particular specifications of following sizes : 1x 16 Sq.mm

Supply of copper conductor PVC insulated, PVC sheath single core unarmoured anti termite and anti rodent treated UG cable for unearthed system of 5 KV grade conforming to IS 1554 Pt II as amended upto date and as specified in particular specifications of following sizes : 1x 6 Sq.mm

Supply of ESNA connector kit suitable for following sizes cable set 6 sq.mm 5kV grade AFL copper conductor cable as required and as specified as per technical specification. 1x 16 Sq.mm

Supply of ESNA connector kit suitable for following sizes cable set 6 sq.mm 5kV grade AFL copper conductor cable as required and as specified as per technical specification. 1x 6 Sq.mm

Supply of 2 core x 4 sq.mm. Secondary cable made out of multi stranded annealed copper conductor PCP sheathed unshielded anti-termite and anti-roddent treated 600 / 660 V grade cable as specified and as required as per technical specification.

Supply of control cables 19 core x 2.5 sq.mm solid annealed plain copper conductor PVC insulated, extended PVC inner sheathed, single layer of galvanised flat steel strip armoured and over all PVC sheathed with anti termite and rodent treated 1.1KV grade confirming IS 1554 Part-I amended upto date as required.

Supply of C.I. Housing Box along with top lead, round type, metal container of size 330 mm dia and 450 mm height made of 10 mm thick cast iron moulding all around, except the top surface which is 15 mm thick suitable to receive a light fitting base plate on top, having clear holes (for AFL cable entry) center 3" above bottom surface suitable to receive 3 nos. 63 mm dia HDPE Pipe & check nut as required. The box should have two Erath Bolts of M-10 x 30 mm welded inside near the cable entry hole on one side and having a drain hole at the bottom suitable tapped to receive 15 mm dia GI Pipee and having clear opening of 220 mm at the top surface and 6 nos M 10 tapped hole at the ceter 260 mm dia to receiv fitting base plate and bolts as required as per the direction of Engineer in-charge.

Supply of double pocketed transformer housing box of overall size 730x330x400 mm, made out of 8mm thick MS plate on four sides and bottom, 10mm thick MS plate for top cover having clear opening of 220 mm at the top surface and 6 nos M 10 tapped hole at the center 260 mm dia to receive fitting base plate and bolts as required including providing stainless steel M-10 size 25 mm long bolts & SS washers, with two side pockets each of size 200x330x400 mm made out of 8mm thick MS Sheet from all sides and 10mm thick top cover having clear openings of 100mm X 230 mm at the top surfaces(of each side) and 6 nos M 10 tapped holes as required for individual pockets,01 No. 15 mm dia drain hole in bottom in each compartment and 8 nos. holes suitable for 63 mm dia HDPE pipe entry, two nos. earthing bolts with nuts etc.near cable entry holes, including painting with one coat of red oxide paint and two coats of black finish paint as required including supply of 2no.s 10mm thick 200 X330mm cover plates for two side pocket with 12no.s SS bolts. for side pockets including gaskets complete in all respects including machining of top surface as required as per the direction of Engineer in-charge.

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 2 core 16 sqmm

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 3.5 core 25 sqmm

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 3.5 core 50 sqmm

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 3.5 core 70 sqmm

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 3.5 core 300 sqmm

Supply of PAPI units complete with 3Nos. of 200W halogen lamp, leg assembly, secondary lead, base plates, etc. Complete in all respect for ready to installation as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of clinometer & precision spirit level and checking stick with base plates etc required for calibration of PAPI units. Complete in all respects as per the directions of engineer incharge of work.

Supply of frangible hinged Illuminated tiltable Wind Cone assembly complete as per ICAO standard and specification with LED red colour PVC dome obstruction marker light Aluminum casting, junction box with 4 nos. of lamps and shades duly fixed in windsock, duly fixed on bearings, including wind sock etc., installed on 75mm dia pipe as main pole, support and hinged base with bolts etc., complete in all respects for ready to installation as per the standrad technical specification and as per the directions of engineer incharge of work.

Supply of Aerodrome Rotating Beacon Type FAA L 802 A ACC. To ICAO Annex 14 Vol.1, PAR 5.3.3 complete in all respect with control panel accessories. i.e. 1000 W lamps etc as required for ready to installation as per the standrad technical specification and as per the directions of engineer incharge of work.

Installation, Testing and Commissioning of following elevated type Runway fittings including installation of Isolating transformer, making connection with secondary lead including setting of horizontal and vertical angles etc. as reqd. and as specified as per technical specification. Runway edge lights/ Apron lights / Taxiway lights / Turning pad lights/Approach lights/Stop way Lights (Simple Approach Lights / CAT -I)

Installation of inset light fixture (runway edge/ Threshold-cum-End/Threshold/End Approach) in existing core including, aligning, setting, providing sealing materials, installation of isolating transformer, supply and crimping & molding of male & female connector kit of OEM approved make with secondary lead at both ends, connection / inter-connections with isolating transformer, providing PVC flexible pipe sleeve & sealing GI pipe at inset fitting side, as per site including testing & commissioning complete as required and as per enclosed specifications complete in all respect.and as specified as per technical specification.

Extra for core cutting in existing PCC of required depth and size suitable for above inset light fittings with core cutting machine complete as required and as per enclosed specifications.

Installation of CI Housing Box with a base concrete of 1:3:6 of size 630x630x100mm thick and all around concrete of 1:2:4 , 150 mm thick, the top sloped with 1:2:4 cement concrete and as specified as per standard specification.

Installation of MS double pocket Housing Box with a base concrete of 1:3:6 and all around concrete of 1:2:4 150 mm thick, the top sloped with 1:2:4 cement concrete and as specified as per technical specification.

Crimping/ fixing of Male/ Female ESNA type connectors on the existing 1x16 sq.mm./1X6sqmm cables with rubber tape, PVC tape etc. complete in all respect as required.

Cutting kerf of suitable size including chipping, hammering, cleaning, drying etc., refilling the kerf with sealant material etc. as reqd. & laying following numbers of secondary leads and as specified as per technical specification.:- 01 No. Secondary cable of size 2x4 sq.mm.

Numbering of Fittings /C.I box with suitable synthetic enamle paint over base of approved colour and pattern as required.

Laying of 1 x 16 /1x6 Sq.mm copper conductor PVC insulated, PVC sheath single core unarmoured of 5 KV grade in the existing RCC / HUME / METAL / HDPE pipe complete in all respect as required and as specified as per technical specification.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 5 KV grade in the existing masonry open duct as required and as specified as per technical specification.

Installation, Testing & Commissioning of PAPI unit with base plate including grouting of checking stick base plate with foundation bolts, with 1:2:4 cement concrete, ground calibration and alignment with other PAPI units, preparation of site, submission of siting calculation for PAPI location, getting approval of siting calculation from Client/AAI including liasioning work etc. Complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Installation, testing and commissioning of wind direction indicator including its control panel for operation in local as well as remote control mode etc. Complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Installation, testing and commissioning of Aerodrome Beacon light on the top of ATC building including its control panel for operation in local as well as remote control mode etc. Complete in all respect to make system functional as per the standrad technical specification and as per the directions of engineer incharge of work.

Installation, testing and commissioning of guidance signboards of various sizes including installation of existing isolating transformer and providing secondary leads etc. including supply of all materials, including pedestal upto 1.5 meter all around the signage with 1:2:4 (cement, concrete, coarse) of thickness 100 mm with neat cement finish plaster, etc., complete in all respect as required as per the standrad technical specification and as per the directions of engineer incharge of work.

Laying of PVC insulated and PVC sheathed / XLPE control cable of 1.1 kV grade of size 19core, 2.5 Sq.mm. in existing perforated cable GI tray/ existing HDPE pipe/ direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required upto 50Sq.mm as per the standrad technical specification and as per the directions of engineer incharge of work.

Design, supply, installation, testing and commissioning of indoor type microprocessor based Constant Current Regulator suitable for remote as well as local control operations with 5 position brightness control for operation on input voltage 230 / 415 V, 50 Hz. AC supply as specified as per technical specification. 30 KW, 20A output current

Design, supply, installation, testing and commissioning of indoor type microprocessor based Constant Current Regulator suitable for remote as well as local control operations with 5 position brightness control for operation on input voltage 230 / 415 V, 50 Hz. AC supply as specified as per technical specification. 20 KW, 6.6A output current

Design, supply, installation, testing and commissioning of indoor type microprocessor based Constant Current Regulator suitable for remote as well as local control operations with 5 position brightness control for operation on input voltage 230 / 415 V, 50 Hz. AC supply as specified as per technical specification. 7.5 KW, 6.6A output current

Design, supply, installation, testing and commissioning of indoor type microprocessor based Constant Current Regulator suitable for remote as well as local control operations with 5 position brightness control for operation on input voltage 230 / 415 V, 50 Hz. AC supply as specified as per technical specification. 4 KW, 6.6A output current

Supplying and providing secondary cable connector as per FAAL-823 for connection of secondary lead with isolating transformer and as specified as per technical specification.

Design, Supply, Installation, Testing and Commissioning of MV Panel for operation on 415V, 50Hz, AC supply made out of 14 SWG CRCA sheet steel indoor type cubical fully compartmentalised, extensible on both sides, totally enclosed dust tight, vermin proof, standing on floor, complete with painting, internal wiring / connections bus bar of following capacity for all 3 phase with a separate bus bar for neutral connection & comprising of the following switchgear & accessories etc. All metering instrument like Digital MFM-02 Nos., Digital Voltmeter - 02 No., Digital Ammeter - 02 No. with 500/5A CT Class 1 ,15VA, LED Indication lamp for R,Y,B and ON with 2A SP MCB - 2 Set, CT for metering complete as required as per detailed technical specification and as per the directions of engineer incharge of work. .

Supply, Installation, Testing and Commissioning of microprocessor based UPS system of 300 kVA rating at 0.9 pf true online UPS using PWM IGBT technology. 3-phase input 415V and input frequency 50 Hz, 3-phase out put fixed setting at 380, 415 and 430V with 30 min. battery backup as specified in technical specification, complete in all respects as required and as specified as per technical specification.

Supply, Installation, Testing and Commissioning of all the equipment required to provide Airfield Lighting Control and Monitoring System (ALCMS), type "L" 890 BB to the requirements of FAA advisory Circular No. AC 150/5345-56B (Current edition) and additional circuits / mechanisms / interfaces for power supply equipment, Landing-H, Wind cone, Beacon & High Masts, etc. to make them compatible with ALCMS, data & power cabling, earthing etc., including all hardware and software, licenses & other items with suitable size UPS for control of all AGL Circuits (including five step brilliancy control of circuits), Landing-H, Wind cone, Beacon & High Masts, if any/etc. as required for successful operation of the system in line with the scope of work, details of equipments, equipments specification, performance criteria etc. complete in all respect as required as per technical specification. The system includes supply of 2 nos. vault processors & providing of connecting additional communication link and LAN cables of required sizes up to Junction box including Supply and Laying of OFC cable in suitable size HDPE pipe (including Supply and laying of HDPE pipe) from CCR HAll to ATC tower to form RING system (OFC) for redundant & fail safe operation to make system functional, complete in all respect as required. Required furniture like suitable desk for the system to suit decor of the ATC Tower shall aslo be supplied.

Design, Supply, Installation, testing and commissioning of junction box made out of 14SWG M.S sheet containing control cable terminals of 10A suitable for 250 cores of 2.5 sqmm copper wire terminations and making connections etc. as required.

Supplying & Fixing Chemical earthling for grounding. Conduits, IC cutouts & other equipments backfill compound which is non-corrosive, thermally conductive, potential to permissible limits, superior Fault conduction capacity, non toxic, weather resistance & capable of achieving ohmic value less than one ohm. Using 10ft. Copper bonded rod with backfill compound

Supply, Installation, Testing & Commissioning of Landing 'H' direction indicator complying ICAO standard consisting of three rectangular AL limbs having length of 4000 mm each supported with 50mm dia Aluminium frangible pipe of 1350mm length & flanges, suitable wattage linear LED lights with driver (minimum IP65) for each limb, each circuits to operate on 230 V, 50 Hz AC supply, providing control unit with suitable control transformer, Relay, Contactor, copper wiring upto JB etc. as required for remote operation of landing 'T' from CCR hall as well as from control tower, connections/ interconnections, civil foundations for each legs with MS anchor base plate, casting pedestal up to 1mtr all around the landing 'H' with 1:2:4 cement concrete of 100mm thick and neat finish top, painting/ powder coating, all required materials & SS hardware etc. Complete in all respect for ready to installation as per the standard technical specification and as per the directions of engineer incharge of work.

Supply and installation of 2mm thick GI raceway with proper ties /clamps at appropriate intervels as per the standrad technical specification and as per the directions of engineer incharge of work. (Cost of support for hanging and coupler for jointing of raceways included). 150mmX38mm

Supply and installation of 2mm thick GI raceway with proper ties /clamps at appropriate intervels as per the standrad technical specification and as per the directions of engineer incharge of work. (Cost of support for hanging and coupler for jointing of raceways included). 150mmX50mm

. SITC of ILS (1no) including civil, network, raw power provisions from nearest location (max 300 mtrs). ii. SITC ofDrishti Transmissometer (RVR) (3 nos) including, civil, network, raw power provisions from nearest location (max 300 mtrs) with load side distribution requirements. iii. SITC of Frangible pre-engineered buildings for housing ILS equipment iv. SITC of Frangible glide path mast and auxiliaries v. Power Cable and elect auxiliaries like load side distribution panel with indication and protection switchgear as per standard vi. UPS’s for equipment’s at each installation location with 30 min back up, vii. Fibre Data Network between equipment to ATC viii. Minimum recommended list of spares for warranty duration ix. Standard Maintenance Tools & Standard test Equipment’s. x. Documentation comprises of User manual, Maintenance manual, Preventive maintenance, Spare part manual with complete OEM part descriptions. xi. Training: 4 User reps for 3 days (ILS & RVR) xii. Warranty: 2 years against manufacturing defects Note: The final specifications for ILS shall be approved by DGCA. The contractor has to undertake the work with modifications as proposed by DGCA at no extra cost. The contractor must quote his rate considering this condition Note: The final specifications for ILS shall be approved by DGCA. The contractor has to undertake the work with modifications as proposed by DGCA at no extra cost. The contractor must quote his rate considering this condition.