Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.7 LAccepted-AOC KAHIKUCHI MARKET P O AZARA ASSAM 781017 | AZARA | KAMRUP | ASSAM | 781017 | L1 | Accepted-AOC RATES ARE FOUND REASONABLE AND THE FIRM BEING L1 BIDDER | |
| 2 | L2₹25.9 L+₹83,729.65 (3.34%)Rejected-Finance STATION ROAD POST RANGIYA DIST KAMRUP ASSAM PIN 781354 | KAMRUP | ASSAM | 781354 | L2 | Rejected-Finance BEING L2 BIDDER | |
| 3 | L3₹26.8 L+₹1.8 L (7.11%)Rejected-Finance | L3 | Rejected-Finance BEING L3 BIDDER | |
| 4 | L4₹27.2 L+₹2.1 L (8.54%)Rejected-Finance C O DR UMASHANKAR SHARMA RANGIYA TINIALI NEAR RAIL GATE POST RANGIYA DIST KAMRUP ASSAM PIN 781354 | KAMRUP | ASSAM | 781354 | L4 | Rejected-Finance BEING L4 BIDDER | |
| 5 | L5₹30.5 L+₹5.5 L (21.8%)Rejected-Finance RANGIYA STATION ROAD WARD NO 2 PO RANGIYA DIST KAMRUP ASSAM PIN 781365 | BAKSA | ASSAM | 781365 | L5 | Rejected-Finance BEING L5 BIDDER |
Tender Value
₹33.8 L
EMD Value
₹67,600
Closing Date
4 Oct 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE RANGIA
GE Rangia C/O 99 APO Rangia
SPL REPAIRS TO BLDG NO ET-43 AND OTHER SANCTIONED WORKS AT TAMULPUR MILITARY STATION UNDER GE RANGIA
2022_MES_550809_1
8600/E8
Open Tender
Miscellaneous Works
Item Rate
180 days
TAMULPUR
AS PER NIT
9 documents required · 9 mandatory
₹500
GE RANGIA
₹67,600
Yes
14 Nov 2022
8 Sept 2022
6 Oct 2022
8 Sept 2022
4 Oct 2022
22 Sept 2022
Amount
Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.
M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.
M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.
M&L for brick work with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.
M&L for rendering 15mm thick on fair faces of brick work or concrete block surface in cement mortar 1:4 , surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.
M&L rendering 10mm thick on other than fair faces of brick work or one side of lathing in cement mortar 1:6, surface to be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.
M&L for form work for side of pillars, posts, columns & similar works vertical or batter complete all as specified and as directed by Engineer-in-charge.
M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as per specified and as directed by Engineer-in-charge.
M&L for providing precast cement concrete 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in louvres and jallies, 35mm thick (measured solid), including all mouldings but excluding frame set in cement mortar 1:4 complete all as per specified and as directed by Engineer-in-charge.
M&L for reinforced cement concrete (nominal mix) type B-l, 1:2:4 (20 mm graded aggregate) as in columns, pillars, piers, posts and struts etc, complete all as per specified and as directed by Engineer-in-charge.
M&L for reinforced cement concrete (nominal mix) type B-l, 1:2:4 (20 mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as per specified and as directed by Engineer-in-charge.
M&L for PCC (1:2:4) type B-1 ( using 20 mm grade crushed stone aggregate) as in benching/coping including necessary form work mould and finished exposed surfaces, complete all as specified and as directed by Engineer-in-charge.
M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.
M&L for mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as per specified and as directed by Engineer-in-charge.
M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.
Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge.
M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as specified and as directed by Engineer-in-charge.
M&L for Machine cut kota stone slab flooring 20 - 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 10 mm thick screed bed or bedding layers in CM 1:4, complete all as specified and as directed by Engineer-in-charge.
M&L for Coloured Glazed ceramic tiles 450 x 350 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick screed in CM (1:4), complete all as specified and as directed by Engineer-in-charge.
S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as per specified and as directed by Engineer-in-charge.
M&L second class hard wood plain fillets, square or rectangular or triangular in section, clean sawn, secured with nails or brads having sectional area exceeding 13 sqcm but not exceeding 25 sqcm complete all as specified and as directed by Engineer-in-charge.
M&L 35 mm thick second class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass and rebated sash bars any numbers etc sizes of member (Bottom 250mm, stiles 100mm, top 120mm & lock rail 160mm wide) as specified in SSR part I section & clause 8.24 (a) complete all as specified and as directed by Engineer-in-charge.
M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as per specified and as directed by Engineer-in-charge.
M&L for RCC (nominal mix) type B-1, 1:2:4 (20 mm graded Agg) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves complete all as per specified and as directed by Engineer-in-charge.
Rounding to edges of stone slabs one edges such as in steps & other similar situation complete all as specified and as directed by Engineer-in-charge.
M&L for 18 to 20 mm thick granite (of any type) tiles, machine cut, bedded & jointed with grey cement slurry & pointed with white cement with admixture of pigmint to match the shade of granite stone including griding & polishing and including 15 mm thick screed bed in CM 1:4 in floorings, complete all as per specified and as directed by Engineer-in-charge.
S&F exposed GI powder coated snap grid frame work for false ceiling of grid size 600x600mm comprising of 2mm dia GI wire as suspender and including 4mm thick non-asbestos cement fibre board of size 595X595 mm including fixing arrangement from roof truss of any type , complete all as specified and as directed by Engineer-in-charge.
M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.
M&L for preparation of new or previously untreated wood or wood based surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.
S&F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge.
S&F aluminium alloy 300 mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.
S&F 300 mm long mild steel Helical door Spring of approved quality, complete all as per specified and as directed by Engineer-in-charge.
S&F 100 mm long stainless steel butt hinges medium weight cold rolled, complete all as per specified and as directed by Engineer-in-charge.
S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.
S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.
M&L for preparing new plastered surface and applying two coats of distemper oil emulsion on wall surfaces over a coat of alkali resistant primer and wall putty complete all as specified and as directed by Engineer-in-charge.
M&L for hardcore of guage not exc. 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as per specified and as directed by Engineer-in-charge.
M&L for 100 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base in flooring/ hard standing, complete all as specified and as directed by Engineer-in-charge.
M&L 75 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in pavement/ hard standing, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.
M&L for Glass dividing strips, 38 x 3 mm thick and inserted in position to confirm to design, complete all as per specified and as directed by Engineer-in-charge.
M&L rendering 15 mm thick on other than fair faces of brick work or one side of lathing in cement mortar 1:6, surface to be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.
Removing excvated materials (soils) exceeding 250m but not exc. 500.00 m and deposited where directed at a level not exc. 1.50 M above the starting point in soil, complete all as specified and as directed by Engineer-in-charge.
Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.
S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.
S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.
Dismantling wall and ceiling boards (fibre, pulp, insulation,etc) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as specified and as directed by Engineer-in-charge.
Taking down cement plaster on brick wall of any description, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer-in-charge.
Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge.
Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.
Demolition of reinforced cement concrete of any description and in any position not otherwise specificied provided for, complete all as per specified and as directed by Engineer-in-charge.
M&L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in flooring/ hard standing/pavings/plinth protections, complete all as per specified and as directed by Engineer-in-charge.
M&L for RCC (nominal mix) type B-1, 1:2:4 (20 mm graded Agg) as in chajjas complete all as per specified and as directed by Engineer-in-charge.
M&L for Formwork to chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges, fair finished surface of concrete flat complete all as per specified and as directed by Engineer-in-charge.
Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed by Engineer-in-charge.
M&L for MS rolled section of grade Fe-410-0 or Fe-310-0 (beam, tee, angle channel ot flat section) as in roof trusses (framed), trussed purlins, crane gantries rails, and fastening and heavy bracket framing including destance pieces, wind tie, cleats etc., complete all as specified and as directed by Engineer-in-charge.
S&F mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed by Engineer-in-charge.
M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over 10cm width or girth complete all as specified and as directed by Engineer-in-charge.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.
S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge.
Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.
Taking down chowkat or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.
S&F Pressed steel frames of size 60 x 125 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including filling of PCC (1:3:6) in 20 mm graded stone aggregate complete all as per specified and as directed by Engineer-in-charge.
Supply and fixing factory made solid panel factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.
S&F Factory made solid wire gauzed pvc door shutter 30mm thick (style) consisting of frame made out of M.S.tubes for top & bottom rails.M.S.frame shall be covered with heat moulded prelam PVC "C" channel having a prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panells will be wire gaused in lieu of single side prelam PVC sheet panel. The wire gause shall be wrapped on an additional square 8 mm MS solid tube and this tube shall be welded to MS tubes. The wire gause shall be stretched to tighten firmly. And jointed to gether with solvent cement, suppling & fixing in the frame at site complete all as per specified and as directed by Engineer-in-charge.
M&L for steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay with glazing bars,dovetailed or welded, complete all as per specified and as directed by Engineer-in-charge.
M&L for steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay without glazing bars,dovetailed or welded, complete all as per specified and as directed by Engineer-in-charge.
M&L for steel ventilators with top hung shutter including hinges, steel peg stay, complete all as per specified and as directed by Engineer-in-charge.
S&F 3 mm thick sheet glass of ordinary quality in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed by Engineer-in-charge.
S&F in repair Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge.
M&L precast coloured glossy finish cement concrete chequered tiles 300x300x25mm thick set jointed and pointed in with grey cement and pigment laid over and including 15 mm thick screed bed in CM 1:6 in floorings, complete all as per specified and as directed by Engineer-in-charge.
M&L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub-base/sub-floors/pavings/floors, complete all as specified and as directed by Engineer-in-charge.
M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 of 80 mm thickness of M-40 grade with grey cement and pigment paver blocks, complete all as per specified and as directed by Engineer-in-charge.
M&L for sand filling under floors or in foundations spreading and levelling in layers not exc. 25 cm thick including watering and consolidation, complete all as per specified and as directed by Engineer-in-charge.
Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.
Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge.
Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as specified and directed complete all as per specified and as directed by Engineer-in-charge.
M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FRLSH copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends . elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLSH copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.
All as per serial item No. 77 above but for one fan point controlled by one switch.
All as per serial item No. 77 above but for one 3 pin 5 Amps socket outlet on independent board.
All as per serial item No. 77 above but for one 3 pin 5 Amps socket outlet on same board.
All as per serial item no. 77 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 15 A socket outlet on independent boards.
Supply and fix switch piano flush type, 6/5 Amps 240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.
Supply and fix ceiling rose surface backelite three terminal complete all as specified and as directed by Engineer-in-charge.
Supply and fix socket outlet multi purpose 2 in 1, 3 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-charge.
Supply and fix switch socket combination 2 in 1, 3 pin, 5/6 Amp flush type universal, complete all as specified and as directed by Engineer-in-charge.
Supply and fix switch socket combination 05/15 Amp 6 pin flush type, complete all as specified and as directed by Engineer-in-charge.
Supply and fix fan regulator electronic type, rotary step, Socket type 240 Volt, complete all as specified and as directed by Engineer-in-charge.
Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and as directed by Engineer-in-charge.
Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed by Engineer-in-charge.
S&F street light fittings 1x 20 Watt LED New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP openning seperate driver compartment with IP65 protection and impact resistance of IK07 and including connection up with twine core twisted flexible copper conductor cable, complete all as specified and as directed by Engineer-in-charge.
S&F steet light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer including taking down old unserviceable one, complete all as specified and as directed by Engineer-in-charge.
S&F in repair sheet metal enclosure powder painted for MCB SPN 8 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.
S&F MCB SPN 240 Volts 40 Amp breaking capacity 10 KA rating, complete all as specified and as directed by Engineer-in-charge.
S&F MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating, complete all as specified and as directed by Engineer-in-charge.
M&L for sand cushioning (dry) in trenches for protection of UG cables (below, above and around the cable laid in trenches) of 230mm spreding thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed by Engineer-in-charge.
Supply & Laying Sub-Class B Bricks, well burnt, laid breadth wise along the length of cable laid in trenches over sand cushion laid for UG cable protection including taking down old unserviceable, complete all as specified and as directed by Engineer-in-charge.
S&F XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of size 16 Sqmm 2 Core including testing of cable and taking down old unserviceable cable, complete all as specified and as directed by Engineer-in-charge.
Supply & laying GI pipe 32 mm bore light grade for protection of UG cable, complete all as specified and as directed by Engineer-in-charge.
S & F ceiling fan hook made out of MS flat 50 X 6 mm thick suitable for hanging of ceiling fan including nuts, bolts and washer with 12 mm dia round bar hook including taking down old unserviceable one, complete all as specified and as directed by Engineer-in-charge.
M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) including taking down old unserviceable one, complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.
M/S KIRAN ENTERPRISE
OM CONSTRUCTIONS
M/S S.S. Construction
M/s SHARMA BUILDERS & ENGINEERS
M/S MICROAPPS SOFTWARE PRIVATE LIMITED
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .