COMPREHANSIVE MAINT OF EM AND BR WORK OF VARIOUS MT GARRAGES AND HANGER AT INS ABHIMANYU AREA UNDER AGE BRII AT NAVAL STATION KARANJA

Amount

Notes : (i) The work is at Ser No.52 of TPP 2025-26. (ii) Please refer schedule 'A' notes before quoting the tender. (iii) Amount of Schedule of Credit shall be deducted off line by the department. (iv)The Unit Rate quoted are deemed to include for the following and nothing extra will be paid for these works: (a). Supplying, erecting and use of scaffolding upto required height (max 25 to 30m) or upto 8th floor height with necessary H-frames, pipes, couplers, buckles, bracing, top platform with support railing at top etc. at all levels of building including carriage of the materials to the location, erecting, fixing the scaffolding and dismembering the same after working and taking away the scaffolding materials etc. complete as per direction of Engineer-in-charge. (b). Supplying, erecting & use of temporary bamboo scaffolding around the building as required. The scaffolding is to be secured properly in position by bracings, ties clamps, etc. complete including providing and erecting working platform at all heights as required, including removal after completion of work all as per direction of Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specifed and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specifed and as directed.

S&F steel work as in tubular trusses including special shaped washer, etc using ERW or induction butt welded tubes confirming to IS 1161 1979 grade St 240 complete all as specifed and as directed.

S&F rolled sections of Fe 410W (Gde-E-250) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specifed and as directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing, wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specifed and as directed.

S&F framed work such as grills, gratings, cooler stands, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls complete all as specifed and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour (as approved) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismanlting of old Sheet complete all as specifed and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour (as approved) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and as directed.

Excavating in post hole (or similar holes) each not exc 0.5 cum in any type of soil, getting out, returning filling in and ramming earth or broken rubble mixed with earth around with earth around in layers not exc 25 cm thick complete all as specifed and as directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, in fencing pole, etc complete all as specifed and as directed.

Preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10 centimetre width or girth and M&L for applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specifed and as directed.

S&F PVC False ceiling consisting of 600mm x 600mm, 8-10mm thick prelaminated hollow self design including frame work made using aluminium T section of size (25mm x 25 mm, 19 gauge or 1mm thick) in square pattern of grid size of 600mm x 600mm. The aluminium frame work is supported from the ceiling with the help of 2mm dia GI wire/ (upto 1200 mm length) adjusting and maintain for proper level to roof slabs by means of ceiling cleats made out of MS flat 40mm x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long. The aluminium frame work is supported on side wall with the use of aluminium 25mm x 25mm angles including taking down of old ceiling frame and board complete all as specifed and as directed. Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.

S&F in repairs 8 to 10mm thick PVC false ceiling consisting of 600mm x 600mm Hollow prelaminated self design insert existing frame work without disturbing the other false ceiling and making good existing frame complete all as specifed and as directed. Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.

S&F false ceiling with Armstrong XL 24mm grid system of grid size 600mm x 600mm with 14mm thick ceiling board of RH-90. Grid shall be suspended from ceiling using 2mm dia pre-straighten GI wire with 6mm nylon rawl plug & screws at 1200mm intervals including taking down old frame and ceiling board complete all as specifed and as directed. Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.

S&F in repairs 8 to 10mm thick Armstrong ceiling board of RH -90 false ceiling consisting of 600mm x 600mm insert existing frame work without disturbing the other false ceiling and making good existing frame complete all as specifed and as directed. Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.

S&F in repairs 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specifed and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet (colour as approved) inclusive of solvent cement and fixing at site on PVC frame including taking down of old wall panelling complete all as specifed and as directed.

S&F of decorative Hollow PVC sheet (colour/shade as approved)10 mm thick (fluted panel) having density not less than 4 Kg/Sqm fixed to wall panelling with self drilling screws including necessary frame of aluminium section 51x35x.55mm and 600 mm c/c 51x32x.55mm grid work and corner mouldings as required as per manufacturing instruction including taking down old Wall panelling with frame complete all as specifed and as directed.

S&F for PVC sheet of 2mm thick laminated plain coloured homogenous, laid with approved rubber based adhesive in floors including taking out old PVC tiles complete all as specifed and as directed.

M&L for 40mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded stone aggregate as in sub-floor, sub-base, floors & pavings, etc complete all as specifed and as directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 20 mm thick screed bed in CM (1:6) for laying floor fineshes including dismentling of old tiles any type complete all as specifed and as directed.

M&L for non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors over & including screed bed or bedding layer of mortar 15 mm in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including dismentling of old tiles any type complete all as specifed and as directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in skirting/dado over & including 10 mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including dismentling of old tiles complete all as specified and as directed.

M&L for vitrified light shade tiles 8 to 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cment slurry and pointed in white or coloured cement to match over & including 20mm thick screed bed in CM 1:6 including dismentling of old tiles complete all as specifed and as directed.

M&L for vitrified light shade tiles 8 to 10mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:4 including dismentling of old tiles complete all as specifed and as directed.

M&L for Glazed ceramic coloured tiles as in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering or bedding layer in CM 1:4 including dismentling of old tiles complete all as specifed and as directed.

M&L for chequered cement concrete tile 30cm x 30cm x 20 to 25mm thick set jointed and pointed in neat cement slurry as in floors, etc with grey cement and pigments over & including 20mm thick screed bed or bedding layer in CM 1:6 including dismentling of old tiles any type complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block, any shape and size (as approved) confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade including dismentling of old tiles any type complete all as specified and as directed. Note:- Sand Cushion shall be measured & paid seperately.

M&L for Machine pressed precast concrete interlocking paver block, any shape and size (as approved) confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including dismentling of old tiles any type complete all as specified and as directed. Note:- Sand Cushion shall be measured & paid sepereately.

Taking down old paver blocks any shape, size and thickness from the existing surface and refixing at the same place after levelling the ground by using sand caushion for maintaing camber and slope complete all as specifed and as directed. Note:- Sand Cushion shall be measured & paid sepereately.

M&L for sand cushioning for laying interlocking paver blocks complete all as specifed and as directed.

M&L for 20 mm thick Granite (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with & incldung 20 mm thick bedding layer in CM 1:4 including dismentling of old stone slab / tiles any type complete all as specified and as directed.

S&F Green marble 16 to18 mm thick, machine cut, jointing and pointing with white cement slurry with & including 20mm thick screed bed or bedding layer of mortar in CM 1:6 including dismentling of oldstone slab/ tiles complete all as specifed and as directed.

M&L for cement concrete type D-2, 1:4:8 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete etc complete all as specifed and as directed.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 using 20mm graded crushed stone aggregate as in plinth protection, finished fair even, laid in bays n.exc 2m in length and joints filled with bitumen mastic 1:3 complete all as specified and directed

M&L for 100mm thick cement concrete type B-2, 1:2:4 using 40mm graded crushed stone aggregate as in path/floor finished fair even and smooth without using extra cement, laid in alternate panels of size not exc 4 sqm each including bitumen filling in joints complete all as specifed and as directed.

M&L for machine cut broken stone or boulders of hard core of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specifed and as directed.

M&L for 20mm thick Wearproof topping as specified (incorporating an approved metallic floor hardner) as per manfacutre's instruction, as specified laid on concrete floors and pavings and path, and finished even and smooth (except metallic hardner) complete all as specifed and as directed. Note: Metallic hardender & glass strips shall be measured and paid separately as supply only.

Supply only 22 mm wide and 3 mm thick glass dividing strips as laid in floor complete all as specifed and as directed.

Supply on metallic hardner mix with cement concrete as per manufacture instruction complete all as specifed and as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specifed and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks, exc.10 cm in width in type B1 (1:2:4) using 20mm graged stone aggregate and setting in CM (1:6) including demolition of old massonry any type complete all as specified and as directed.

M&L brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean raidus built in cement mortar 1:6 including demolition of old massonry any type complete all as specified and as directed.

M&L brickwork with sub class 'B' bricks, (except bricks) straight or curved on plan exc 6m mean raidus built in cement mortar 1:6 including demolition of old massonry any type complete all as specified and as directed. Note:- Serviceable bricks obatined from demolition of brick work shall be re-used after cleaning etc

M&L for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 including demolition of old Stone masonary complete all as specifed and as directed.

M&L for walling of random rubble, (except stone) brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 including demolition of old Stone masonary complete all as specifed and as directed. Note:-Serviceable stone masonary obatined from demolition of Stone mansonary shall be re-used after cleaning etc

M&L for raised pointing to random or polygonal rubble masonry uncoursed or brought upto course in CM (1:4) complete all as specified and directed.

M&L for raised pointing to precast concrete block masonary wall in CM (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick/concrete surfaces with two coats i.e (10 mm thick backing coat and 5mm thick finishing coat) finished even and smooth complete all as specified and directed. Note:- Quoted rate shall be include any height of Bldgs for scafolding as all arrangement.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth complete all as specifed and as directed. Note:- Quoted rate shall be include any height of Bldgs for scafolding as all arrangement.

S&F in repairs 12 mm thick Toughned glass as in hinged doors, partitions automatic doors and similar works including cutting to shape, drilling holes required complete all as specifed and as directed.

S&F in repairs 30 mm dia stainless steel handle of 60 cm long and fixed to toughned glass as per manufacturer's instructions complete all as specifed and as directed.

S&F in repairs stainless steel glass lock fixed to toughened glass as per manufacturer's instructions complete all as specifed and as directed.

Taking down aluminium doors shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket, new aluminium beads & cleats of existing make and also refixng the handles & mortice lock in existing postiion with and including new screws including refixing the door shutters in same opening complete all as specified and directed. Note : If broken or unserviceable glass/aluminium wire mesh/floor spring/concealed lock is replaced same will be paid separately under relevant items.

Taking down aluminium windows shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket, new aluminium cleats of existing make and also refixng the locks & roller in existing postiion with and including new screws including refixing the window shutters in same opening complete all as specified and directed. Note : If broken or unserviceable glass/aluminium wire mesh/floor spring/concealed lock is replaced same will be paid separately under relevant items.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) not exceeding 1.5 Sqm each, removing from the site including cutting holes required for taking out existing hold fast etc complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 sqm not exceeding 4.0 Sqm each, removing from the site including cutting holes required for taking out existing hold fast etc.complete all as specified and as directed.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each including iron mongrey & removing from site complete all as specifed and as directed.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each and refixing in same opening after resecuring or easing , and adjusting complete all as specifed and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. (variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made) complete all as specifed and as directed.

S&F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specifed and as directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F in repairs stainless steel tubing of 25 mm dia for curtain rod fancy type including fancy type rings and brackets (wall to wall or flush to wall) for securing to curtain rod, complete all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube and edges will be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube top & bottom rail mild steel frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F for aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading,screws etc, complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, hooks & eyes, peg stays and handles including connected items, with and including making good to the disturbed portion with its original specifications complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality ,fixed in aluminium Door /window shutter area n. exceeding 0.50 Sqm each pane complete all as specified and as directed.

S&F 4 mm thick sheet glass, ordinary quality ,fixed in aluminium Door /window shutter area exceeding 0.50 Sqm each pane complete all as specified and as directed.

S&F for concealed star lock powder coated for aluminium window fixed as per manufacturers instructions complete all as specified & as directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specifed and as directed.

S&F in repairs to aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specifed and as directed.

S&F 4 mm thick sheet glass, ordinary quality, glazing with oil putty or with wooden beads, area n. exceeding 0.50 Square Metre each pane including hacking out old glass complete all as specified and as directed.

S&F 4 mm thick sheet glass, ordinary quality, glazing with oil putty or with wooden beads, area exceeding 0.50 Square Metre each pane incluidng hacking out old glass complete all as specified and as directed.

S&F for rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window/doors etc complete all as specified and as directed.

S&F in repairs to aluminium anodised grill of design DG 104 pattern made out of 10mm dia rod fixed with and including standard aluminium frame of F section of size 23.40mmx15.30mm & 1.4mm thick all as per manufactures instructions complete all as specifed and as directed.

S&F in repairs for Double action floor spring hydraulically regulated made up of minimum 1.25mm thick alum,inium alloy sheet foundation box, main ody with stainless steel cover, governing pivot made of brass, other plart made of mild steel heavy duty and fixed complete all as specifed and as directed.

S&F in repairs floor door stopper of Aluminium alloy body and tongue, over all length of cover plate 150mm anodised with hard drawn steel spring, fixed to shutters complete all as specified and as directed.

S&F in repairs mild steel body 4 lever Mortice lock vertical type size 100mm complete all as specified and as directed.

S&F in repairs 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, and both faces is covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick, and all around side faces is covered with decorative lipping complete prepared as cup board shutter and fixed with wooden frame-work complete alll as specified and directed

S&F in repairs Cabinet Hinges Soft Close SS 8 Crank complete all as specified and directed

S&F in repairs 9mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed

S&F of stainless steel butt hinges size 100 complete all as specified and as directed.

S&F in repairs to stainless steel butt hinges size 100 complete all as specified and as directed.

S&F Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F in repairs Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F Aluminium anodized, barrel tower bolt of extruded section, length of bolt 150 mm complete all as specified and as directed.

S&F in repairs to Aluminium anodized, barrel tower bolt of extruded section, length of bolt 150 mm complete all as specified and as directed.

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mmAngle valve stopcock cast copper alloy, screwed down high pressure chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm fancy type, pillar taps, cast copper alloy, with capstain head chromium plated screw down high pressure, with or without lettered HOT or Cold with long shanks and fly-nuts screwed for iron pipes and fixed complete all as specifed and as directed.

S&F in repairs PVC flushing cistern of 10 ltrs capacity including flush pipe PVC connection etc complete all as specifed and as directed.

S&F in repairs white vitreous china wash down water closet pan (Pedestal pattern) with and including P or S trap, including plastic seat cover closed pattern, fixing bolt etc complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, of size 580mm x 440mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, CI trap 100 mm Bore of pipe etc complete all as specifed and as directed.

S&F in repairs Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed

S&F in repairs to casket type wash down water closet with seat cover , waste pipe, cistern with lid & fittings complete all as specifed and as directed. Make: M/s Hindware (Cat No: 92045) or equivalent as approved by GE.

S&F in repairs vitreous China wash hand basin white, flat back of size 550mm x 400mm fixed on and including cast iron cantilever bracket, Waste fittings, 32 mm dia waste couping of brass,chromium plated including fixing of tap, waste fitting etc complete all as specifed and as directed.

S&F in repairs 32mm dia PVC waste pipe for WHB and urinals complete all as specified and directed.

S&F in repairs 15 mm dia PVC connection 450mm longwith brass fly nut complete all as specifed and as directed.

S&F in repairs 15 mm dia PVC connection 600mm longwith brass fly nut complete all as specifed and as directed.

S&F in repairs 15 mm wash basin mixutre, single lever extended basin mixer (height 95mm) with popup waste system with 450mm long braided hoses, chromium plated, screwed down high pressure, screwed for iron pipe etc and fixed complete all as specifed and as directed.

S&F in repairs to Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specifed and as directed.

S&F in repairs Tubular towel rail made of brass chromium plated , 20mm dia, D type, 60cm long between flanges complete all as specifed and as directed.

S&F in repairs CP Towel rack 600mm long with lower hangers complete all as specifed and as directed.

S&F in repairs CP toilet paper holder with stainless steel flap complete all as specifed and as directed.

S&F in repairs 15 mm bib cock, two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe complete all as specifed and as directed.

S&F in repairs soap dish holder of bootom Cp and glass holer for soap complete all as specifed and as directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs corner glass shelf (with bracket) complete all as specifed and as directed.

S&F 160 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with stock clamps including taking down of old pipe line any type complete all as specified and as directed.

S&F for PVC (SWR) bends any radius 160mm bore complete all as specified and as directed

S&F in repairs 75mm bore PVC(SWR) bends any radius with access door complete all as specifed and as directed.

S&F in repairs 110mm bore PVC(SWR) bends any radius with access door complete all as specifed and as directed.

S&F 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down of old pipe line any type complete all as specified and as directed.

S&F 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls iincluding taking down of old pipe line any type complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement 75mm bore complete all as specified and directed.

S&F 15 mm bore GI tubing medium grade, galvanised with all fitting and fixed complete to walls and ceilings or laid in floors including taking down of old pipe line any type complete all as specified and as directed.

S&F 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches including taking down of old pipe line any type complete all as specified and as directed.

S&F 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches including taking down of old pipe line any type complete all as specified and as directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specifed and as directed.

Preparation of new plastered surfaces of walls and M&L for applying two coat of oil distemper over and including 1 mm thick wall care putty and filling cavities with wall care putty after completely removal of existing treatment complete all as specified and as directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint over & including one coat of primer complete all as specified and as directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint in camouflage patterns as directed over & including one coat of primer complete all as specified and as directed.

M&L for PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in coping bed black etc including nessesary form work complete all as specified and directed.

M&L for greasing and easing in position of mild steel rolling shutters of area n.exc 10sqm each for full movement and for easy operation of shutters including taking down & refixing of old shutter if required complete all as secified and as directed.

M&L for greasing and easing in position of mild steel rolling shutters of area exc 10sqm and n.exc 20sqm each for full movement and for easy operation of shutters including taking down & refixing of old shutter if required complete all as secified and as directed.

M&L for greasing and easing in position of mild steel rolling shutters of area exc 20sqm and n.exc 50sqm each for full movement and for easy operation of shutters including taking down & refixing of old shutter if required complete all as secified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position, area of shutter n.exc 10sqm each complete all as secified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position, area of shutter exc 10sqm and n.exc 20sqm each complete all as secified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position, area of shutter exc 20sqm and n.exc 50sqm each complete all as secified and as directed.

S&F rolling shutter without ball bearing, thickness of laths 1.00mm including top cover, anchoring rod, hasp and staple, gear operated type with chain wheel and hand chain and primer erected in position including taking down of old Shutter any type complete all as specified and as directed.

S&F Steel rolling shutters, with out ball bearing, thickness of laths 1.00mm as specified including top cover, anchoring rod, hasp and staple and erected in position as indicated,complete: push pull or manual type including taking down of old Shutter any type complete all as specified and as directed.

Preparing new or previously untreated steel surface of any decription over 10cm in width or girth and M&L for applying 2 coats of aluminium paint over & including one coat of red oxide primer complete all as specified and directed.

Preparing old painted steel surface of any decription over 10cm in width or girth and M&L for applying one coat of aluminium paint complete all as specified and directed

S&F in repairs stainless steel 304 grade framed work fancy/ornamental type as in Gates/stairs, hosing work and other similar works including all type of welding, holdfast, locking arrangement, followed by buffering and polishing for smooth finish including taking down of old railing/pillars any type complete all as specified and as directed.

S&F in repairs 25mm PVC float valve high pressure of PTMT with epoxy coated aluminium rod & hight density plastic ball complete screwed for iron pipe or brass furred and fixed with fittings such as (socket, nipple, union) etc complete all as specifed and as directed.

S&F in repairs 20mm PVC float valve high pressure of PTMT with epoxy coated aluminium rod & hight density plastic ball complete screwed for iron pipe or brass furred and fixed with fittings such as (socket, nipple, union) etc complete all as specifed and as directed.

S&F in repairs Gunmental, globe or gate valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specifed and as directed.

S&F in repairs Gunmental, globe or gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specifed and as directed.

S&F in repair Gunmental, globe or gate valves 15 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specifed and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hosting if required, reconneting and refixing in position capacity exc 250 and n exc 500 ltr. including cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipes etc complete all as specifed and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hosting if required, reconneting and refixing in position capacity exc 500 and n exc 1000 ltr. including Cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipes etc complete all as specifed and as directed.

E/M WORKS

Taking down carefully copper /aluminium point wiring (light, fan socket or power) through stove enamelled steel conduit/PVC conduits including complete fittings such as switches, ceiling roses, pendants, regulators, sockets,, switch sockets, electrical fittings etc removing and making good disturbed surfaces of walls/ceiling etc, complete all as specified and as directed.

M&L for point wiring fo light/fan/bell point controlled by 1 one way switch using 1.5 Sqmm single core, multi stranded copper conductor 1100 V grade, ISI marked, PVC insulated unsheathed cable (with approved colour code) FRLSH cable drawn in & including PVC casing caping (ISI marked) of 25 mm wide double locking type including all accessories with & including PVC 1.5 Sqmm multi stranded insulated unsheathed FRLSH copper wire, ISI marked of green colour for continous earth, including sunken box made out of suitable thickness and not less than 60 mm in depth GI/MS/ prssed steel terminal box to be concealled in wall, duly painted including 3mm hylum /masonite sheet cover, for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : Wiring to be done as per approved colour code.

All as per BoQ Serial Item no.2.44 above but for One light point controlled by 2 way switch SP, 5 Amp, 240 Volts complete all as specified and as directed.

All as per BoQ Serial Item no.2.44 above but one 5 amp socket point on same board complete all as specified and as directed.

All as per BoQ Serial Item no.2.44 above but one 5 amp multi socket indepenedent complete all as specified and as directed.

All as per BoQ Serial Item no.2.44 above but using 2.5 sqmm (nominal area) multistranded FRLSH copper conductor cable/wiredsaz & 2.5 sqmm size PVC insulated unsheathed copper conductor cable for earth continuity (green colour) for one 5 pin socket outlet 5/15 Amp multi purpose independent point controlled by 15 Amp switch, SP one way, 240 Volts & Socket, complete all as specified and directed.

All as per BoQ Serial Item no.146.00 above but using 4.0 sqmm (nominal area) multistranded FRLSH copper conductor cable/wiredsaz & 4.0 sqmm size PVC insulated unsheathed copper conductor cable for earth continuity (green colour) for one 5 pin socket outlet 5/15 Amp multi purpose independent point controlled by 15 Amp switch, SP one way, 240 Volts & Socket, complete all as specified and directed.

S&F Switch piano type flush button type single pole one way 5/6 Amps 240V front operated complete all as specified and directed.

S&F Switch socket combination 2 in 1 3 pin, 5 A and 15Amp flush type universal complete all as specified and directed.

S&F socket 3 pin 5 A flush type complete all as specified and directed.

S&F Bell buzzer 240v 50hz complete all as specified and directed.

S&F Bell push 240v 50 hz complete all as specified and directed.

S&F ceiling rose PVC/polycarbonate, isolated body surface Bakelite 65mm dia three terminals complete all as specified and directed.

Fixing only in repairs any type of light flame proof, high bay, low bay, etc to any height including minor accessories, tranportation complete all as specifed and as directed. NOTE: Light fitting shall be provided by the department.

M&L for Sub main wiring with two runs of single core PVC insulated unsheathed cable 1100 volts grade, multistranded copper conductor FRLSH cable of 6.0 Sqmm (with colour code), drawn in but including non metallic rigid PVC conduit of 25mm dia/casing capping/suitable size, ISI marked including one run of PVC insulated unsheathed, multistranded copper conductor FRLSH cable of 6.0 Sqmm (Green colour) as contineous earth conductor cable connected to earth dolly in surface/ recess complete including taking down any type complete all as specified and as directed.

S&F in repairs MCCB, 4 pole, thermal magnetic release range 100 Amps of breaking capacity 16 kA, 415 Volts, 50 Hz complete all as specified and as directed.

S&F in repairs MCCB, 4 pole, thermal magnetic release range 125 Amps of breaking capacity 16 kA, 415 Volts, 50 Hz complete all as specifed and as directed.

S&F in repairs MCCB, 4 pole, thermal magnetic release range 63 Amps of breaking capacity 16 kA, 415 Volts, 50 Hz complete all as specifed and as directed.

S&F in repairs MCCB, 4 pole, thermal magnetic release range 40 Amps of breaking capacity 16 kA, 415 Volts, 50 Hz complete all as specifed and as directed.

S&F in repairs 6 to 32 amp, MCB, single pole, 240 V, 10 KA (C-Series) complete all as specifed and as directed.

S&F in repairs High bay LED light hanging/ceiling mounting type, 100w fitting with PC diffuser with surge protection on existing light point with suitable hanging arrangements one light control with one MCB SP, complete all as specified and directed. Note:The rates includes taking down old light fitting and providing suitable necessary ladders /equipments for any height for taking down/fixing new one.

S&F in repairs LED recess/surface mounted 2" x 2" luminarie 36/40w fitting, 220V,AC, 50 Hz, suge protection, high power factor complete all as specifed and as directed.

S&F in repairs double door MCB, VTPN, DB 4, way made out of 18 SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 100 Amps rated bus bar 4 way complete all as specifed and as directed.

S&F in repairs Low bay LED lights hanging/ceiling mounting type, 40w fitting with PC diffuser with surge protection on existing light point with suitable hanging arrangements one light control with one MCB SP, complete all as specifed and as directed.

S&F in repairs 32 AMP MCB SPN 240 V 10 KA (C-Series) complete all as specifed and as directed.

S&F in repairs LED batten with 20/22W LED tube light (4"), 220V AC, 50Hz in wall/surface connecting with all required accessories like PVC box base, flexible cable from ceiling rose etc, surge protection, high power factor, surface and wall mounted LED batten, complete all as specifed and as directed.

S&F in repairs round/square type, recessed /surface 12W/14W warm /white LED downlight dimmable with high lumen 230V complete all as specifed and as directed.

S&F in repairs switch piano flush button single pole one way, 6 Amp complete all as specifed and as directed.

S&F in repairs Switch socket outlet 2 in 1, 3 pin, 6 Amp flush type complete all as specifed and as directed.

S&F in repairs Socket outlet 2 in 1, 3 pin, 6 Amp flush type complete all as specifed and as directed.

S&F in repairs Switch socket outlet 15 Amp, 5-in-1, controlled by one switch complete all as specifed and as directed.

S&F in repairs Socket type EME fan 5 step regulator for ceiling fan of suitable size complete all as specifed and as directed.

S&F in repairs modular step type fan regulator, 120W, AC, 50Hz complete all as specifed and as directed.

S&F in repairs modular switch 1 module 6 amp one way complete all as specifed and as directed.

S&F in repairs modular switch 1 module 16 amp one waycomplete all as specifed and as directed.

S&F in repairs modular socket 2 module universal type 5/6 amp one waycomplete all as specifed and as directed.

S&F in repairs modular socket 2 module universal type 15/16 amp one way complete all as specifed and as directed.

Supply and fix repair/replacement modular bell push 6A 1 module complete all as specified and directed.

S&F in repairs ceiling rose three terminal complete all as specifed and as directed.

S&F in repairs LED tube rod 20 watt, 220V, 50Hz,AC change with existing any tube rod complete all as specifed and as directed.

S&F in repairs double door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 12 way double door, openable type complete all as specifed and as directed.

S&F in repairs double door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 8 way double door, openable type complete all as specifed and as directed.

S&F in repairs modular cover plates with frame up from 1 /2 to 3 module as per site requirement complete all as specifed and as directed.

S&F in repairs modular cover plates with frame up from 4 to 12 module as per site requirements complete all as specifed and as directed.

S&F repair/replacement modular metal flush box as per site requirements from 1/2 to 3 modules complete all as specified and directed.

S&F repair/replacement modular metal flush box as per site requirements from 4 to 12 modules complete all as specified and directed.

S&F repair/replacement LED building security light 45 watt with hanging arrangement in wall/surface/ceiling connecting with all required accessories like PVC box base,flexible cable from ceiling rose etc Surface and wall mounted LED batten, including taking down, Engineering plastic batten with accessories complete all as specified and directed.

M&L for daily complaint checking & repairing of DBs/meter panel board/circuits/submain wiring/switches/sockets etc and other connected work including rectification of faults complete all as specified and directed

M/s S.D Construction Co (BID ID -3415505)

M.K Enterprises (BID ID -3415218)

pk Enterprises (BID ID -3413458)

S.P.TRADERS (BID ID -3413191)

S K ENTERPRISES (BID ID -3413638)

OM ENTERPRISES (BID ID -3415044)

M/S Rana Enterprises (BID ID -3415078)