Renovation / Beautification / Upgradation of Crematorium in Owala-Majiwada Constituency Thane Municipal Corporation limits.

Amount

Removing King Post truss from roof and stacking the materials as directed with all leads andlifts etc. complets (SSR Item No 46.04)

Dismantling flat wooden or A.C. Sheet ceiling with frame work including stacking the materials as directed with all leads, lifts etc. complete. (SSR Item No 46.06)

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. (SSR Item No 46.09)

Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete. (SSR Item No 46.14)

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. (SSR Item No 46.15)

Removing ventilators and small windows with frame and stacking the materials with all leads, lifts etc. complete. (SSR Item No 46.16)

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete (SSR Item No 46.19)

Removing earthen, stonewate pipe and stacking them as directed with all leads, lifts etc. complete. (SSR Item No 46.27)

Removing cast iron or wrought iron or A.C. pipe and stacking them as directed with all leads, lifts etc. complete. (SSR Item No 46.28)

Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. (SSR Item No 46.29)

Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complete (SSR Item No 46.40)

Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bedcon-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls outside etc. carefully and throwing out the refusal outside etc. complete. (SSR Item No 46.41)

Trimming of grass, shurbs and weeds from the shoulders/berms and disposing off the same to suitable locations etc. complete

Cutting down trees including trunks and branches with girths above 60cm to 90cm and stacking the materials neatly with all lifts and lead of 1000m. as directed and earth filling in the depression/pit if any.

Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Manual Means

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Providing and erecting chainlink fencing 1.6M. height with G.I. chainlink of size 50x50 mm ,8 gauge thick and fixed75mm above ground level on vertical M.S.Angles of 40x40x6mm size, including excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450x450x670mm. at 1.75M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30cm c/c with nut sand bolts and horizontal M.S.Angles at top and bottom of 25x25x5mm size and vertical M.S.flat35x5mm and 25x5mm horizontal including cross support of 40x40x6mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450x450x670mm including 3 coats of oil painting etc.complete.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 10.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing soling using 80 mm size granite / quartzite / gneiss / trap metal in 15 cm. layer including hand packing filling voids with sand / grit, ramming, watering complete. (Spec. No. : As directed by Engineer-in-charge /Page No. 154)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying/pumping cover blocks,compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layersincluding watering and compacting etc. complete.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand (in plinth)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/ Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and roughening the mif special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing bituminous pad 25mm thick for expansion joints in retaining wall, compound wall etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing fly ash brick masonry with conventional /I.S. type bricks in cement mortar1:6 in super structure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring

Providing and laying in position flooring of telephone black /Amba White /Catbary brown/Ruby red/Ocean Brown granite stone of approved shade and size 18mm to 20mmt hick on bed 1:6 cement mortar including cement floats striking joints,pointingin C.M. 1:3 curing and cleaning etc. complete.

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design,including cleaning,washingand finishing etc. complete.

Providing and fixing machine cut mirror polished 18mm to 20mm thick telephone black/AmbaWhite/Catbarybrown/RBIred/OceanBrown granite stone partition with full moulding the edges etc.complete. One side polish

Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and fixing machine cut mirror polished 18mm to 20mm thick telephone black/AmbaWhite/Catbarybrown/RBIred/OceanBrown granite stone partition with full moulding the edges etc.complete. One side polish

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete

Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry,curing,polishing,moulding edges,cleaning complete.a) Marble other than white makrana

Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .

Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete.

Providing and fixing 90cmx60cm Granite plate engraving 10cm. Height letter,figures including painting the lefters/figures with approved colour and shade complete

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35x35x5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65mm and 3.15mm respectively with hold fast arrangements, M.S. Bracket plate 300x300x3.15mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheel sand worm so fhigh grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S.62481979) (Without mechanical gear)

Providing and Fixing 30 MM thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19 mm for styles and 15 x15 mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 mm (+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles ; and 5 mm thick ,95 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm (+/0.25) x 30 mm PVC sheet beading on either side and joined together with solvent cement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100 mm x 25MM x 2mm using 32 mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/Running metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/Running metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box.Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/Running metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/Running metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box.

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80x38mmx1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete.

Providing and Fixing mat finish stainless steel (of 302 grade) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 mc/ coras required and horizontal pipes of 25 mm dia in three rows, all pipes of 2mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex. Engineer is necessary before use)

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete.

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing In Rs. plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black backlite seat with all necessary pipe connection etc. complete.

Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Providing and laying for 150 mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and laying for 225mm dia. salt glazed S.W. Pipe including fitting such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete

Providing and laying in walls/ceilings/floors 25 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and laying in walls/ceilings/floors 20 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 1.63 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing Autoclosing pillar cock of pressmatic tap of approved make or equivalent including all fixtures, fittings etc. complete.

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5liters flushing cistern with fittings,inletpipe with stop tap,brackets for fixing the cistern,32mm diameter P.V.C.flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall.

Providing and fixing machine cut machine polished 18 mm to 20mm thick Rock pavar Block for Pathway of approved colour and shade with on bed of 1:4 Cement mortar including float filling joints and cleaning etc. complete (Cobblestone)

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)

Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete. Spec. No. : As directed by Engineer-in-charge. (TATA Steel) (SSR Item No 23.11)

Providing and fixing Ductile iron Man Hole Covers /Strom Water Grating and Grating with frame of Various sizes,weight and types and load bearing capacity as perEN-124,equivalent NECO with prior approval of concerned Superitending Engineer.

Providing and fixing plain zinc sheeting of 0.80 mm thick (22 B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised iron screws and bolts, lead and bitumen washers etc. complete.(Weight of 6.8 Kilogram/sq.m.)

Providing and fixing 22 B.W.G. plain FRP sheets on top of weather shed, including scaffolding, fixing by means of nut and bolts or as directed etc. complete. (Brackets of 70 x 45mm to be paid separately)

Providing and casting in situ or precast tapering R.C.C. M-20 Mountable type Kerb with gutter (as per IRC 861983) embedded 125 mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff anywhere in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant (SSR Item No 7.06)

Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogram. to 20 Kilogram. Per Sq.m.) Spec.Number: As directed by Engineer- in-charge.

Providing & Fixing FRP Entrance Gate 5.6 mt Length and 2.5 mt height (Quation) As derected by Enginner -in- Charge.

Providing and Fixing Wood Pyre with Cast Iron Stand with Installation

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mm dia G.I. pipe (Rezan/concentiDeletedire0.75mmdia)with hot dip and G.I.coated hooks as per drawing supported on M.S. angle 50x50x6mm at 2.5mtr. c/c including fixing and fastening with wire,painting M.S. angles with one coat of red lead primer and two coat of oil paint etc. complete.

Providing and laying in situ/ Ready Mix cement concrete M-25 of trap / granite/quartzite/gneiss metal for R.C.C. work in foundations like raft, strip foundations,grill age and footings of R.C.C.columns and steel stanchionsetc.including bailing out water,Steel centering form work,laying/pumping coverblocks,compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Typemixer/concreteBatchmixplant(Panmixer)etc.complete.Withfineaggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C.slabs and landings as per detailed designs and drawings including steel centering,formwork,cover blocks,laying/pumping,compaction finishing the formed surfaces with cement mortar1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc.complete, (Excluding reinforcement and structural steel).with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Typemixer/concreteBatchmixplant(Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthem if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and applying waterproofing treatment using acrylic polymer modified cement based waterproofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre/ Kilogram with two coat using approved chemicals form asonryandconcrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. Complete

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complet

Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts grouted in wall complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

ISupplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) fitted with necessary accessories complete as per specification no. FF-FFA/HV

Supplying fire fighting reinforced rubber lined (R.R.L.) hose pipe, 63mm dia, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying & erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Supplying and erecting fire brigade header (Siamese connection) of 150 mm dia for supplying water to wet riser system complete as per specification no. FF-FFA/SMC

Supplying and installing air vessel of 300 mm dia 1.5m in height M.S. tank installed inside pump house / on terrace complete as per specification no. FF-FFA/ACT

Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FFVL/ BFV

Supplying & erecting cast iron double flange butterfly valve of size 100 mm dia. complete as per specification no. FFVL/ BFV

Supplying & erecting cast iron double flange butterfly valve of size 75/80 mm dia. complete as per specification no. FFVL/ BFV

Supplying and erecting cast iron double flange NRV of size 150 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 100 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 75/80 mm dia complete as per specification no. FFVL/ NRV

Excavation : Excavation for foundation in soft strata which does not required blasting up to 1.5 Mtr. depth including removing the Excavated material up to a distance of 50 Mts. beyond the building area and lift. (PWD-DSR 2015-2016) P-5 / I-A-1

GARDEN SOIL :- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size Free from stones rubbish like dried grass roots and other such materials. The soil should be fresh be measured by measuring box (Farma) Item includes royalty charges, octroi, corporation Tax Transporting, loading – unloading etc

Farm yard manure :- Supplying on site well decayed, well dried, well powedered, withought clods and free from stones, dried grass and other rubbish material,. The colour of the manure generally be black. the manure will be measuring by measure box. (farma) item includes Transporting, loading -unloading etc (lead charges per 40km. are considered.

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms. Mixing garden soil and manure thoroughly will levelling, watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering weeding clopping rolling etc. complete

Preparing Shrubbery :- Excavating the round to required depth of 30cms, removing and conveying unwanted stuff to a required excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil & manure toughly well, leveling , watering on previous As derected by Engineer-Incharge.

Supplyings & planting of plants required for landscaping:- Euphorbia, hemelia, Malphejia, Ticoma, song of India, Golden bamboo, Bhudhhaj bamboo, golden ficus, Phonicu palm, x mass trees ficus panda, etc. (height of plant 5-6 ft )

Planting large flowering / shady trees :- Digging pit with size 0.9m x 0.9m x 0.9m removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 0.30m and remaining height of 0.60m with fresh garden soil & manure in 3:1 proportion Mixing soil & manure thoroughly well. leveling as directed, watering previous night, planting on to two year old healthy trees sapling as per specifications. Maintaining till well established by watering weeding, stirring of soil replacing of casualties etc. complete.

Providing forest trees putranjiva, jaccaranda, bakula, kecia, Neem, shoka Gulmohar 8 feet to 10 feet.

Providing and supplying palm trees vaieties, red palm, fox tail palm, botttol palm, Rhaphis palm, Table palm, Cristle palm, cene palm, Ashoka etc.. Size 10-12 feet

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Excavation for foundation in hard murum and boulders including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Excavation for roadway in hard rock by wedging and chiselling or line drilling including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 10.0 to 19.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing dry / trap / granite / quartzite / gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying PCC in M15 grade levelling course of 100 mm thick below pile cap with fully automatic micro processor PLC with SCADA enabled reversible drum type mixer / concrete batch mix plant (pan mixer) . etc. Complete for PCC.

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing and laying in situ/ readymix M-30 controlled reinforced cement concrete of trap metal for raft slab including "V" haunches, formwork, scaffolding ,compaction by vibrating, finishing curing etc. complete. concrete batch mixplant/ pan mixer with fine agreegates of required specifications (Natural sand/ VSI sand finely washed etc)etc. complete. (excluding reinforcement). a)RCC Grade with reversible drum type mixer/ concrete batch mix plant, for Raft Concrete.

Providing and laying in situ / ready mix M20 RCC of trap/ granite/ quartzite/ gneiss metal for RCC work of ballast walls, kerbs and box returns including scaffolding, compaction, formwork finishing and curing etc. complete. (excluding reinforcement, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc ) RCC work of Ballast walls & Kerb

Providing and laying in situ / ready mix M-30 controlled cement concrete of trap / granite / quartzite / gneiss metal for RCC work in solid / deck slab etc. including ramming, vibrating, curing, formwork, centering and finishing in cement plaster excluding reinforcement etc. complete. (with fully automatic microprocessor based PLC with SCADA enabled concrete batch mix plant / pan mixer and Natural / VSI standard Artificial Sand)

Providing and laying weep holes of 100mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Providing and fixing in position steel fibre reinforced concrete (S.F.R.C.) frame and covers of approved make including loading, unloading, transportation, all taxes, etc. complete as directed by Engineerin-charge (20 tonnes capacity). (size - 0.90m x 0.60m)

Transportation of excavated material like silt,earth,murum,building rubble,concrete blocks etc. complete. (Lead upto 7 kms.)

Providing and applying priming coat on concrete / masonary / Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Excavation for roadway in soft rock, including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading or stacking as directed.

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed. By Manual Means. (with prior permission of S.E.)

Transportation of excavated material including loading and unloading etc. complete. d) lead upto 10 km.

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete.

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Materia

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller. to the required density. By Mechanical Means - Grading I (Using Screening Type A (13.2) mm Aggregate)

Providing and Laying M60 grade cement concrete of approved mix design with avg. Flextural strength of 4.4 MPa in 3 days from R.M.C. plant incld. use of micro silica/alcofine, approved make super plastiser and retarder, fibriliated 100 % virgin polypropylene fibres, fly ash and transported by transit mixer and placing at work site. Compacting, finishing, initial curing by approved curing compound/ contractors water and tarring the sides of slab with hot bitumen as specified and as directed (w/c ratio 0.28 max.). (vatta for curing will be paid separately) for Ultra thin White Topping (UTWT) pavement. etc completed.

Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.

Designing, providing and installation of wall Mural outside compound wall. The material for this work is Fibre/FRP. Length of Mural 15M X 3M .Size of Mural Shall be proporsionate to the height of mural. Thickness of FRP material 5 to 10 mm. Including all cost of design making modls making murals, ispection charges, transporatation, fixing at site( City Beatification Quotation)

Exhaust Hoods made of SS 304 Stainless Steel of 2mm thick size 2.450 M X 1.550 M X 0.920 M with transportation, erection at site complete with design and drawing

Central Outlet made of SS 304 Gauge 14 Size 610 mm X 610 mm with transportation, erection at site complete with design and drawing

Square Shape bend made of SS 304 Gauge 14 with transportation, erection at site complete with design and drawing

Square to round reducer made of SS 304 Gauge 14 L 600 mm with transportation, erection at site complete with design and drawing

Damper assembly made of SS 304 thick 3 mm with transportation, erection at site complete with design and drawing

Exhaust Duct made of SS 304 thick 2 mm dia 450 mm with transportation, erection at site complete with design and drawing

Damper assembly by pass made of SS 304 thick 3 mm with transportation, erection at site complete with design and drawing

Scrubber to blower duct made of SS 304 thick 2 mm dia 450 mm with transportation, erection at site complete with design and drawing

Flange for ducts @ 1.5 Mtrs made of M. S. 40 mm width, 5 mm thick with transportation, erection at site complete with design and drawing

Tie rods For Supporting hoods and ducts with transportation, erection at site complete with design and drawing

Brackets Made of M. S. for Supporting hoods and ducts with transportation, erection at site complete with design and drawing

Graphite packings 6mm thick (30 Pieces)

Castable refractory high alumina supar castable for 1000 °C temperature

Water Scrubber made of SS 304 thick 3mm scrubber dia 1400mm, height 2500mm and baffle plate 6 mm thic. Gases entering tangentially to create cyclonic movement with transportation, erection at site complete with design and drawing

Nozzles Bergan 20 make

Scrubber supports M.S ISMC 150 channels

Chromium plated nut bolts 16 Nos for each joint of duct

Water Tank 5000 ltrs capacity 1.5 M X 2.5 M X 1.35 M above the ground level

water Pump 2 HP

Plumbing GI pipe 1inch Inlet 2 Inch Outlet 'C' class galvanised pipes 1"inch 30 Meter,2"inch 30 Meter

Drain water control valve

Blower assembly made with SS 304 3 mm thick impeller and casting with stiffeners, 20 HP motor , V Pulley and belt fitted pn M.S I beam frame with transportation, erection at site complete with design and drawing

30M self supporting type M.S chimney with transportation, erection at site complete with design and drawing with base dia 1200 mm, top dia 600 mm. Frist 6 Meters 10 mm thick , Second 6 Meters 8 mm thick ,Third 6 Meters 6 mm thick , Fourth and Fifth sections of 6 Meters each 5 mm thick

M. S. Bottom plate 25 mm thick 1600 mm X 1600 mm with transportation, erection at site complete with design and drawing

Support plates M.S plate 6 mm thick 150mm X 65mm with transportation, erection at site complete

M.S Gusset 200mm X 65 mm 8mm thick

M.S Gusset 600 mm X 285 mm 12 mm thick

M.S Flanges 10mm thick 740 mm-600mm Dia

Foundation Bolts High teensile steel 25 mm dia 1.8 M long with nuts

Lightning arrester Copper plate of 25 mm X 6mm

Pilot Lamp On top of the chimeny 230 VOLTS, 5 Amp

Insulators For lightning arrester, Insulators 20 mm thickness

Earthing pit for chimney

M.S Helical Stack 65mm X 5MM thick flat on the Surface of the chimeny with transportation, erection at site complete with design and drawing

Painting 2 coats of heat resistant paint to Chimney 400°C Heat Resistan Paint 2 Coats, Red Oxide Primer Paint 1 Coat of Reputed Brands likes Asian Paints/ Nerolac

M.S Ducting From Scrubber to chimney with transportation, erection at site complete with design and drawing, M. S. 5 mm Thicknes

Electric Panel with Switches, Starters, contactors, relays, pilot lamps busbars, with brands likes Siemens/ L&T (410 Volts 3 Phase /20 Amps)

S.S Ducting By Pass with transportation, erection at site complete with design and drawing

SS Chains 4 Metrers Long For Dampers of 6 mm Thicknes of Length

Electrification for Smoke control system

RCC Foundation for 30 M tall M. S. chimney 2.5 M X 2.5 M X 2 M

Removing the existing SS Water scrubber system with both sides connecting MS pipes and fitting new SS water scrubber and MS pipe connection dully lined from inside from cremator to SS scrubber and up to the existing chimney

Main Cremator with complete refractory lining of fire bricks, insulating bricks and 25mm thick ceramic wool total 375mm thickness of lining

Door lifting box cover

Counter weight box for 500 kgs dead weight

30 Meter height self supported M.S. Chimney with ladder, lightning arrestor, inspection hole, manhole etc.

M.S. Chimney section 10 inch diameter x 5 feet long internally lined with heat resistant refractory castable

S.S.304 water scrubber with plumbing

Body charging trolley approx. 765mm wide x 3700mm long

M.S. Trolley base frame of 50mm x 25mm channels

Mesh belt for conveyer of 10 gauge carbon steel approx. 500mm wide x 8000mm long

M.S. roller 2” dia 560mm long

M.S. roller 14” dia 560mm long

Rubber lined roller 150mm dia

Air blowers 3 HP

Gas burner 30 kgs/hr capacity for LPG

Air pipe line

Ceramic fiber 25mm thick blanket

M.S. pipe 8” dia x 10’ Long

M.S. pipe 1” dia

M.S. channel 60mm x 30mm

Instrument control panel for 3 nos of pilot lamps, 9 fuses, 100 Amps Bus bars suitable for 415 V, 3 Phase supply, 2 nos of contactors with relays dully wired

Globe valve 2.5”

Barrel nipple12” Long

Short bend 2.5” dia

Tee Joint 2.5”

Reducer 2.5” x 1.5”

Reducer 2.5” x 2.0”

Barrel nipples 6” Long

Barrel nipple 1.5” Long

Side cover plate panel 16 gauge M.S. fabricated floor mounted

Chain cover

M.S. plate 6mm thick x 9’ x 5’

Short bend 8” dia

M.S. flange 8” dia

M.S. nut & bolts with washers

Transmission chain

Gear box unit

Electric Motor 1.5 HP

3 core wire

Starter 3 HP

Ignition transformer 230/15000 V step up transformer with cables

Push button

Flexible PVC pipe

Wire rope 6mm

M.S. fabricated Fluid collection duct

M.S. Motor frame

M.S. Gear box frame

M.S. channel 4” x 2”

Ball bearing 25 mm

Ball bearing 38 mm

Fire Fighting equipments

15 KVA Gen set

Providing Skilled Labour for operating Gasifire and smoke controll system

Monthly Maintenance for Gasifire & smoke controll sytem

Supplying and Laying PVC Trunkimg ( PVC Casing-n-caping) of size 25 MM with necessary accessories

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON

Supplying & erecting mains with 2x1.5 sq.mm F.R. solid copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/Bus bars or any other places as per specification No: WGMA/BW

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting modular type switch 16A ISI mark approved make duly erected on provided plate and box with wiring connections complete

Supplying and erecting modular type bell-push 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6/16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected in an approved manner.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected in an approved manner.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 8 module duly erected in an approved manner.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module duly erected in an approved manner.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 16/18 module duly erected in an approved manner.

Supplying and erecting modular type electronic step regulator two module ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG PW/CW

Point wiring for independent plug, concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG PW/CW

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board.

Supplying and erecting storage type horizontal / vertical water heater 25 litres capacity with BEE 5 star rating high impact resistance engineering plastic body on wall / loft complete duly tested and marking sr. no. and date of erection. specification no.AP-WH/STWH

Supplying and fixing wire mesh (Jali) cover suitable for fitting / fan or for any purpose, complete with necessary materials. The jali cover shall be made from good quality G.I. wire mesh size 25 x 25 (mm) and made up of 14 SWG G.I. wire with side / supporting MS strips of suitable size.

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22 / E-27 base.

Supply and erection of 17W to 20W LED Batten WH PVC (5700K to 6000K) CRI>70%, Lumen efficacy> 100 lumens per watt, Voltage 230V AC

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying Pedestal fan 400 mm. 230 Volts 50 cycles oscillating type complete with guard and regulator 3 mtrs. of flexible wire and hand shield type 3 pin plug top.

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation

S & E exhaust fan heavy duty 230 V A.C. 50 cycles 375 /380 mm., 900 RPM . Complete erected in position as per specification no. FG-FN/EXF

Supplying and erecting Fan hook 10 mm. M.S.

Supplying and erecting ‘B’ grade G.I .pipe /M.S. pipe down rod duly painted for fan complete erected with PVC two core flexible cable 24/0.2 mm copper PVC wire

Providing and erecting air circulator 600 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for 230/250 volts single phase, 50 cycles A.C. supply, core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation.

Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warranty.

Supplying & erecting four pole ON LOAD change over switch, 415V, 100A, open execution having staggered termination, phase barrier, shroud termination and terminal cover along with auxiliary contacts and ready to upgrade with fuse protection kit, rotary handle, operational current category AC23A complying to IS/IEC 60947-3 Part-1/3.

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6 A to 32 A B- series (for lighting) in provided distribution board as per s pecification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A in provided distribution board as per specification No. SWSWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification No. SWSWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP (12 Poles)/TP (4 Poles) MCB of 4 ways (12 Poles), on iron frame/laminated board.(Vertical Busbar type) as per specification

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW- WR/MCBDB

Providing, erecting & commissioning RCCB only of electro magnetic type with 30/100/300 MA sensitivity and having 16/25A. 4 pole complete as per specification No. SW-RCCB/RCCB

Providing, erecting & commissioning RCCB only of electro magnetic type with 30/100/300 MA sensitivity and having 63A. 4 pole complete as per specification No. SW-RCCB/RCCB

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with Encloser 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SWRCCB/RCBO

Supplying, erecting & terminating XPLE armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no.CB-LT/AL

Supplying, erecting & terminating PVC armoured cable 4core 25 sq mm aluminium conductor with continuous 5.48 sq mm (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 4 core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Making trench of suitable width and depth in soft soil for laying provided LT cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification

Supplying and erecting G.I strip of required size used for earthing on wall and / or any other purpose with necessary GI clamps fixxed plate size 60 x 60 x0.6 cms. complete with all materials, testing & recording the results as per specification No. EA-EP

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Providing & erecting 4 Pole MCCB of 250A, 415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI rame as per specification no. SW-SWR/MCCB

Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Supplying and erecting extended rotary handle for MCCB with adjustable telescopic rod suitable for upto 250A MCCB complete.

Supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500V 400A complete as per specification no. CP-BB

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Supplying & erecting LED type indicating pilot lamp with LED colour blue, 230 / 250 V on provided box / panel with necessary material, wiring & connections etc.

Providing and installing of Cu links of 16 sq.mm with copper lugs for connecting the switchgear to Busbars

Providing and installing of Connector for 200A, connector type CTS70L.

S & E of aluminium strip to provide the support for the connectors

Supplying and erecting dual source intelligent flush mounted panel meter three phase four wire (IPM) 415V CT/ PT site programmable class I flush mounted (96 x 96mm) meter with voltage, current, frequency, power factor , ON hrs, kWh, EB and DG set metering with LED display (excluding CT'S) complete with RS 485 communication protocol, class I accuracy and wiring connections and mounting hardware on provided panels complete with calibration certificate from manufacturer.

Providing and erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio with 15VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates

Supplying and erecting terminal spreaders for use on MCCB incoming and outgoing terminals for 4 pole above 250A upto 400A MCCB complete. (Set of 8)

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH PL/OP

Providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete,excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supply and erection of Hot dip galvanized Ring for installation of mini high mast suitable for 4 Nos of LED Flood lights. The outer dia of ring shall be 600 mm. The ring shall be of 50 mm dia B class pipe with three supports to Sleeve, the sleeve shall be of 500 mm length and 4 mm thick duly provision of 4 nos bols and shall be suitable to fit on Octagonal pole of 70 mm AF.

Supply and erection of BREEZA Type decorative hot dip Galvanized Single arm bracket of 1Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min 3 mm thick with cap pipe length of 0.45 Metersuitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or it's equivalent as per the drawings enclosed.

Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete

Supply and erection of BREEZA type decorative hot dip Galvanized Double arm bracket of 1.0 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 21.3 mm OD pipe, min 2.5 mm thick with cap pipe length of 1.0 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 5 to 12o as directed by Engineer - in - charge

Supplying and erecting pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. strip complete with all materials as per specification no. EA-EP

Supply Installation Testing & commissioning of Integral high pressure Die cast/extruded aluminum LED Streetlight luminary the system wattage (fixture's total power consumption)should be 90W +/- 5 Watt Details as per technical specification attached.

Supplying and erecting integrated LED flood light fitting Max. 150W

Supplying and erecting integrated LED flood light fitting Max. 200W

Supplying & erecting mains with 3x2.5 Sq.mm F.R stranded/solid copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Supplying & erecting PVC armoured cable 4 core 10 Sq. mm. stranded/solid aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing M20 concrete for resurfacing the road.

Supplying, erecting & marking SPMCB 0.5A to 5A in provided distribution board as per specification no.CB-SB

Providing, erecting & commissioning RCCB only of electro magnetic typewith 30/100/300mA sensitivity and having capacity of 16/25A 4pole complete as per specification No. SWRCCB/RCCB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification No. SWSWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B- series (for lighting) in provided distribution board as per specification No. SWSWR/MCB

Supplying and erecting bakelite sheet 6 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete.

Supplying and erecting enamel iron G.I. sheet 1.6mm (16 gauge) caution board of size 200 x150 mm. as per I.S. 2551 of 1982 in Marathi and Hindi erected at position for medium installation.

Supplying & erecting mains with 2x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG MA/BW

Supplying & erecting Single Pole Bakellite 35 Sqmm connector for connecting wire from MCB to cable

MCB/RCCB Channel Support patti

Supplying & erecting approved make 415V 63A porcelain base neutral link complete erected in provided M.S. box.

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

Providing powder coating of approved color shade on both sides of provided iron work / MS /CRCA sheet steel work complete including antirust treatment in an approved manner.

Supplying and erecting Iron, sheet metal work consisting of CRCA Sheets, Various sections of iron, Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority

Providing cement concrete for foundation or for concrete filling in 1:3:6 ratio with 20 to 25 mm. stone metal duly plastered with necessary curing for pole muffing or any other purposes.

Supplying and erecting 4 pole power contactor 440V 40A for time switch complete erected on wooden block/provided box, with necessary materials.

Supplying & erecting crimping type copper lugs for cable upto 16 sq mmcomplete as per specification No. CB-L/CU

SITC of nature switch infrared for making ON/OFF street light as sun set and sun rise. The nature switch shall be housed in FRP casing with protection of MCB opening voltage 150V to 300V 30-60 Hz

Supplying & erecting FRP box of size 250 x 200 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. CB-SB

Supplying & erecting FRP box of size 150 x 125 x 100 mm,2.7 mm thick complete on pole/wall as per specification no. CB-SB

Supplying, erecting, testing and commissioning self contained water cooler 230/250 V 50 cycles nominal cooling capacity of 80 litres/hr and storage capacity 120 litres with partially stainless steel body complete. specification no. AP-WCR/WC

Supplying and erecting ultra violet water purifier with softener for safe drinking water consisting of UV germicidal tube of 8W capacity, choke made of copper wire, two indicator lamps, dual function cartridge with output of purified water 2 litre/min. with activated carbon filter and softener operating on 230 V single phase AC supply.

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 50 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 9.98 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 150 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 50 kVA up to 62.5 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Supply, installation, testing & commissioning of 4MP IP Bullet Camera with 1/2.8", progressive scan, CMOS, 4/6mm lens@ F1.8/2.0, angle of view more than 82° WDR 120db or above, Illumination Colour: 0.02 Lux (F1.8), 0.0Lux with IR, Day/Night with auto switch ICR, supported H.264/H.265 MJPEG video compression, Smart function supported motion , IP66,CE, ROHS.

Supply Installation Testing & commissioning Of Network Video Recorder 32 channel input, Support 2-ch HDMI Up to 12 Megapixels resolution recording, Support RAID 0, 1, 5, 6, 1 & 8 SATA HDDs, Up to 8TB for each HDD, Support N+1 Hot spare, Support for 12V Power output, HDMI/VGA Output, Recording Resolution, Resolution 12MP/ 6MP/5MP/4MP/3MP/1080p /960p/720p /D1/2CIF/CIF, Compression H.265/H.264, 8 SATA interfaces, Capacity up to 8TB for each HDDs, Array Type RAID 0, 1, 5, 6, 10.

Supply Installation Testing & commissioning of 6000 GB Hard Disk for video Surveillance Equivalent to:- Western Digital /Seagate

Supply Installation Testing & commissioning of 43" LED TV Monitor Equivalent to:- LG/Samsung

Supplying and fixing 6UWall Mount Rack (Dimension-DxWxH 450x550x367 mm) as per specification No. WG-NAS/RAK

Supplying & erecting UPS of 1KVA capacity complete with standard features, along with necessary SMF batteries for 20 mins. battery backup

Supplying and installing cat-6 armoured cable with ECCS tape suitable for networking as per specification No. WG-COC/NC

Supply , Installation, Testing & Commissioning of UTP Connector (RJ-45) as per specification No. WG-AS/UTPC.

Supplying, fixing, and configuring 8-ports 10/100/1000 Mbps unmanaged gigabit PoE Switch complete.

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mAh Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 hrs. with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20% having useful life of minimum 25000 hrs. with overheating protection with 2 years warranty.

Supplying, erecting, testing and commissioning 120 W amplifier suitable to operate on 230 Volts A.C. / 12 Volts D.C. supply complete as per specification no. FF-PA/AFR

Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC

Supplying, erecting, testing and commissioning stand mounted/handheld type wired microphone having 2 mV/Pa sensitivity, impedance level limit 300 ohms and 50 - 16000 Hz suitable to operate in -10 deg C to +55 deg C with min. 7 metre shielded cable and 3 Pin Professional XLR Connector, stereo jack complete as per specification no. FF-PA/MIC

Supplying, erecting, testing and commissioning rust free microphone floor stand of chrome plating/powder coating or S.S. material , 500 mm to 1500 mm height and sturdy mechanism ensuring trouble free movement complete.

Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per specification no. FF-PA/MCC

Supplying and erecting triple pole mini feeder pillar with 500V, 300A FPMCCB as incomer and 3 outgoing circuits with HRC fuse base and cartridge of 100A with aluminium bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket having IP54,IK10 protection and slanting top to be erected on provided foundation as per specification no. SW-SWR/MFP

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Second Year Comprehensive maintenance of all electrical works (5% of Estimate Cost)

Third Year Comprehensive maintenance of all electrical works (10% rise on second year Miantenance Cost)

Fourth Year Comprehensive maintenance of all electrical works (10% rise on Third year Miantenance Cost)

Fifth Year Comprehensive maintenance of all electrical works (10% rise on Fourth year Miantenance Cost)

S.B.Khakal