Augmentation of water supply system for left out portions of Sudhana Nagar and surrounding areas in Zone X, Mudaliarpet, Puducherry

Amount

Earth work in excavation by mechanical means (Hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m - all kinds of soil - pipes,cables etc , exceeding 80mm dia but not exceeding 300 mm dia

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Centering and shuttering including strutting , propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete

Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in lintels, beams, and bressumers including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering and shuttering but excluding the cost of reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

12 mm cement plaster of mix 1:4 (1 cement :4 course sand)

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:4:8 or leaner mix (including equivalent design mix)

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - water bound macadam road

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - bituminous road

Labour for cuting C.I.pipe with steel saw - 100 mm diameter C.I.pipe

Labour for cuting C.I.pipe with steel saw - 150 mm diameter C.I.pipe

Labour for cuting C.I.pipe with steel saw - 200 mm diameter C.I.pipe

Labour for cuting C.I.pipe with steel saw - 250 mm diameter C.I.pipe

Labour for cuting C.I.pipe with steel saw - 300 mm diameter C.I.pipe

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 100mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 150mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 200mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 250mm diameter pipe.

Providing and fixing C.I. sluice valve (PN 1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 150 mm dia.

Providing and fixing C.I. sluice valve (PN 1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 200 mm dia.

Providing and fixing C.I. sluice valve (PN 1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 250 mm dia.

Providing and fixing C.I. Double air valve with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 150 mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -100mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -150mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -200mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K7 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -300mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -150mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -200mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -250mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -100mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -150mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -200mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -250mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -300mm dia.

Providing and fixing in position S&S standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing and fixing in position flanged standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing and fixing D.I. MJ collar coupling , with bolts, nuts, rubber insertion etc.,complete - 100 mm dia.

Providing and fixing D.I. MJ collar coupling, with bolts, nuts, rubber insertion etc.,complete - 150 mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -100mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -150mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -200mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -250mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -300mm dia.

Supply and installation of DI D/F Gate Valves (Soft seated ) Resilient seated soft sealing gate valves (Sluice valves ) (Make VAG,AVK,Fouress) with body bonnet of ductile iron of grade GGG 40, wedge fully rubber lined EPDM of good quality W720 , replaceable spindle nut, without gland packing and with 3 O-ring protection on the shaft and seals of NBR and the valves should be vacuum tight and 100% leak proof with face to face dimensions as per BSS 163-89/ISI 4846 - 2000/DIN3202 F4. All the valves should be Electrostatic powder coated both inside outside with pocket less straight thro body passage. All the valves shall be compatible for burried application without chambers, with pressure rating PN 10/16 - dia 150mm

Supply and installation of DI D/F Gate Valves (Soft seated ) Resilient seated soft sealing gate valves (Sluice valves ) (Make VAG,AVK,Fouress) with body bonnet of ductile iron of grade GGG 40, wedge fully rubber lined EPDM of good quality W720 , replaceable spindle nut, without gland packing and with 3 O-ring protection on the shaft and seals of NBR and the valves should be vacuum tight and 100% leak proof with face to face dimensions as per BSS 163-89/ISI 4846 - 2000/DIN3202 F4. All the valves should be Electrostatic powder coated both inside outside with pocket less straight thro body passage. All the valves shall be compatible for burried application without chambers, with pressure rating PN 10/16 - dia 200mm

Supply and installation of DI D/F Gate Valves (Soft seated ) Resilient seated soft sealing gate valves (Sluice valves ) (Make VAG,AVK,Fouress) with body bonnet of ductile iron of grade GGG 40, wedge fully rubber lined EPDM of good quality W720 , replaceable spindle nut, without gland packing and with 3 O-ring protection on the shaft and seals of NBR and the valves should be vacuum tight and 100% leak proof with face to face dimensions as per BSS 163-89/ISI 4846 - 2000/DIN3202 F4. All the valves should be Electrostatic powder coated both inside outside with pocket less straight thro body passage. All the valves shall be compatible for burried application without chambers, with pressure rating PN 10/16 - dia 300 mm

Supply and installation of DI D/F Gate Valve (Soft seated ) Resilient gate valve (Sluice valve) (Make VAG, AVK, Fouress) with body bonnet of ductile iron of grade GGG 40, wedge fully rubber lined EPDM of good quality W720, replaceable spindle nut, without gland packing and with 3 O-ring protection on the shaft and seals of NBR and the valves should be vacuum tight and 100% leak proof with face to face dimensions as per BSS 163-89/ISI 14846 - 2000/DIN3202 F4. All the valves should be Electrostatic powder coated both inside and outside with pocket less straight thro body passage. All the valves shall be compatible for burried application without chambers, with pressure rating PN 10/16 - dia 100mm

Providing and fixing non-corrosive Engineering plastic moulded clamp saddle with stainless 304 threaded metal inserted for tapping outlet suiting for ½" clear bore with SS 304 wide strap with elastomeric insulation for proper grip around the DI pipe with SS 304 suitable bolts & nuts saddle to have sealing rubber SBR grade 30 o-ring around shall as detailed in the drawing furnished. The rate includes all labour charges for fixing bracket etc., complete as per instructions of Engineer-in-charge size 100 x 25 mm dia (3/4)

Providing house service connection for each house from the newly laid distribution grid with 25mm dia (OD) PN16, MDPE blue pipe PE 80 as per ISO 4427 Rev.1 & tested as per BS 6920 upto 1.00 RM length initially with 90 degree compression elbow as per ISO 14236 and polypropylene male & female thread metal insert (SS 304) of ISO 14236. The cost include connection charges for making drilling holes and providing specials as per the direction of Engineer-in-charge

Providing, laying and jointing MDPE (PN 16) pipe PE 80 as per ISO 4427 as per specification BS6920 over and above initial 1m length including transportation to the site,lowering to the trenches, laying to the proper grade and alignment etc. complete all as per specification - 25mm outer dia

Excavation for roadwork in soil with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections and transporting to the embankment location with all lifts and lead upto 1000m.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth three wheeled steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite Crushable type such as moorum / gravel for screening and gravel for binding to fill up the interstices of coarse aggregate, watering and compacting to the required density - by manual means - Water bound macadam Gr-I with Gravel screening. (As per MoRTH specification, 4th Revision)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth 3 wheeld steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisitecrushable type such as moorum or gravel for screening and gravel for binding to fill up the interstices of coarase aggregate, watering and compacting to the required density by manual means - water bound macadam Gr-II with moorum or gravel screening (as per MoRTH specification, 4th Revision)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth 3 wheeled steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type B screening and binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density - by manual means - Water bound macadam Gr-III with moorum or gravel screening. (As per MoRTH specification, 4th Revision)

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means. (As per MoRTH specification, 4th Revision

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg. Per sqm. on the prepared bituminous / granular surface cleaned with mechanical broom. (As per MoRTH specification, 4th Revision)

Providing and laying open graded premix carpet of 25mm thick on prepared surface in a single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6-10 tonne laying manually and rolling with power roller 8-10 tonne but excluding cost of primer/tack coat. As per clause no 509 of MOST specification.

Providing and applying premixed seal coat type `B' comprising of thin application of fine aggregate premix with bitumen binder in mini hot mix plant, carriage manually of mixed material and laying and rolling with power roller 8 to 10 tonne. As per clause no 513 of MOST specification.

GST @ 18% for Items No.1 to 69 above

G SANKAR

Kavipriya Contractors

B KATHIRAVAN

L Djegaradj Moncher