SUPPLY and ERECTION OF COMPLETE ELECTRICAL for Bhandara District Rice Mill Cluster.for M/s. Bhandara District Rice Millers Cluster Pvt. Ltd

H. T. WORKS

RSJ POLES 116 X 100 MM, 12 MTR. LONG

11 KV 'V' CROSS ARM

11 KV TOP CLIP WITH CLAMP

H.T. STAY SET

G.I. STAY WIRE

HT STAY CLAMP/ CROSS ARM with 50x10 MS FLAT

H.T. EARTHING SET

BENTONITE POWDER

11 KV PIN INSULATOR WITH G.I. PIN

11 KV DISC INSULATOR 70 KN

STRAIN HARDWARE

SINGLE POLE CUT POINT SET

ACSR/AAAC up to 100 Sq mm Dog Conductor

ACSR/AAAC up to 55 Sq mm Dog Conductor

11 KV, 400 A, A.B. SWITCH

A.B. SWITCH FABRICATION SET

11 KV HORN GAP SET

11 KV LIGHTNING ARRESTOR

LA/HARN GAP/DP TOP CHANNEL with 75x40x6mm MS Channel

GUARDING CHANNEL WITH CLAMP 100 x50x6 mm

M.S. NUT BOLTS & WASHERS

G.I. WIRE 8 SWG

G.I. FLAT 50 X 6 MM FOR TRANSFORMER BODY & NEUTRAL EARTHING

11 KV 3C X 185 SQMM. XLPE CABLE

OUTDOOR JOINTING KIT FOR 11 KV 3C X 185 SQMM CABLE

INDOOR JOINTING KIT FOR 11 KV 3C X 185 SQMM CABLE

STRAIGTH THROUGTH JOINTING KIT FOR 11 KV 3CX185 SQMM CABLE

FULL ROUND RCC PIPE 200 MM DIA

HALF ROUND RCC PIPE

G.I. PIPE 4" DIA

DANGER BOARDS

BARBED WIRE

PAINTING OF POLES WITH RED OXIDE & ALUMINUM PAINT

CONCRETING 1:4:8

SUNDRIES

MAINTENANANCE FREE 17.2 MM DIA, 3 MTR LONG COPPER BONDED EARTHING SET COMPLETE WITH 2 BAGS OF COMPOUND AND FRP CHAMBER COVER ETC. OF APPROVED MAKE

COPPER FLAT 50 x4MM for EARTHING

TRANSFORMER Supply, Installation, testing and commissioning of following capacity 11/0.433 KV, 3 phase, 50 Hz, copper wound step down Oil immersed transformers WITH LEVEL-2 (4 STAR RATING), with Off circuit Tap Changer .Lifting arrangement IP-23, Class of Insulation - 'A' Temperature Rise Winding Over Ambient of at principal tap 55 Degree C, Winding Material Electrolytic Copper Tapping Range on HV Winding For HV Variation + 5% to -10% in steps of 2.5%, Two Earthing Terminals, Diagram and rating plate, Duty Cycle: Continuous, In-built HV and LV cable boxes, dial type ( analog type ) WTI with A/T contacts shall be provided + Trip Contact. STRICTLY AS PER ATTACHED SPECIFICATIONS.

LBS 11KV

HT Metering Cubicle of 'HUPEN' Make

VCB 11 KV I/Door CT/PT (CTR=400-200-100/5-5A)

LIAISON WORK Liasoining work with Electricity Board, PWD Electrical Inspector and other statuary authorities for getting approval for all electrical sanctions, including but not limited to the following

Plan Approval

Permission for charging the system

SAFETY ITEMS IN SUBSTATION Supplying following safety items required for substation as a Set

Fire Extinguisher 5 kg ( ABC Type.) – 2 Nos.

Sand Buckets (9 lit) with Stand (2 Nos in a Set) – 1 Sets.

First Aid Box – 1 No.

Shock Treatment Chart written in English & Local Language – 2 Nos.

Danger Boards written in English & Local Language – 2 Nos.

Tool Kit with 11 kV Rubber Gloves – 1 Set

Rubber Mat 12 mm thick

Rubber Mat 6 mm thick

Approved Single Line Diagram framed in A2 size glass frame in the substation: 1 Set

LT WORK LT PANELS Design, Supply & Installation of LT Panels fabricated out of 14 gauge CRCA Sheet Steel in cubicle compartmentised free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T’ section and / or flats wherever necessary, all gland plates should be detachable & shall be fabricated out of 3 mm thk. sheet steel, panel should be powder coated as per shade provided. All panel drawings shall be spproved prior to taking up manufacturing.

Main Panel as per Single Line Drawing enclosed

MCC - 1 Panel as per single Line Drawing enclosed

MCC - 2 Panel as per Single Line Drawing enclosed

Please Note : All MCCB's must be provided with panel operating mechanism & spacer sets for all terminals. All MCCB's of 200 A & above rating should be of 35 kA rating, 100 A MCCB should be 16 kA rating & All MCB's should be of 10 kA rating with C curve. The drawings for panel shall be approved before taking up manufacturing & minor changes if any are included in contractors scope.

LT CABLES & TERMINATION Supply, handling, laying proper connections testing and commissioning of following sizes of 1.1 KV grade PVC insulated Armored Copper/ Aluminum conductor or cables laid over MS supports cable racks / trays or fixing on walls including clamping supports.

3.5C x 400 Sq. mm AL. XLPE Cable

3.5C x 300 Sq. mm AL. XLPE Cable

3.5C x 240 Sq. mm AL. XLPE Cable

3.5C x 185 Sq. mm AL.AYFY Cable

3.5C x 150 Sq. mm AL. AYFY Cable

3.5C x 120 Sq. mm AL. AYFY Cable

3.5C x 95 Sq. mm AL. AYFY Cable

3.5C x 70 Sq. mm AL. AYFY Cable

3.5C x 50 Sq. mm AL. AYFY Cable

3.5C x 35 Sq. mm AL. XLPE Cable

3.5C x 25 Sq. mm AL. XLPE Cable

4C x 16 Sq. mm AL XLPE Cable

4C x 10 Sq. mm Cu XLPE Cable

4C x 6 sq.mm. AL XLPE Cable

4C x 6 Sq. mm Cu XLPE Cable

3C x 2.5 Sq. mm Cu XLPE Cable

TERMINATION KIT Supplying and fixing compression type brass Cable Glands for PVC and armored cable with brass washers, rubber rings complete erected with cable ends leads including supply and fixing of Cu/Al lugs confirming to IS suitable for cables evenly crimped with NOTE: SINGLE COMPRESSION GLANDS ARE CONSIDERED IN OUR OFFER.

3.5C x 400 Sq. mm AL. XLPE Cable

3.5C x 300 Sq. mm AL. XLPE Cable

3.5C x 240 Sq. mm AL. XLPE Cable

3.5C x 185 Sq. mm AL.AYFY Cable

3.5C x 150 Sq. mm AL. AYFY Cable

3.5C x 120 Sq. mm AL. AYFY Cable

3.5C x 95 Sq. mm AL. AYFY Cable

3.5C x 70 Sq. mm AL. AYFY Cable

3.5C x 50 Sq. mm AL. AYFY Cable

3.5C x 35 Sq. mm AL. XLPE Cable

3.5C x 25 Sq. mm AL. XLPE Cable

4C x 16 Sq. mm AL, XLPE Cable

4C x 10 Sq. mm Cu YWY Cable

4C x 6 sq.mm. AL XLPE Cable

4C x 6 Sq. mm Cu YWY Cable

3C x 2.5 Sq. mm Cu XLPE Cable

DISTRIBUTION BOARD Design as per SLD Providing and fixing angle iron frame Lighting/ Power Distribution Boards Flush mounting/ Concealed Type, Double Door type as per of approved make MCBDB and comprising with IP 42 of the following: Powder Coated Double Door Type Distribution Board.

4 Way TPN MCB DB with Incomer 63 A RCCB, Outgoing - 6/10/16 A SP MCB - 12 Nos.

6 Way TPN MCB DB with Incomer 63 A RCCB, Outgoing - 6/10/16 A SP MCB - 18 Nos.

12 Way phase sagregated TPN with 63 A TP MCB as incomer, 63 A DP RCCB 100 mA rating as sub incomer & out going 6/10/16 A SP MCB - 36 Nos.

12 Way VTPN MCBDB with 125 A TP MCCB as incomer, 6 nos. 32/63 A TP MCB as outgoing & 6/10/16 A SP MCB - 18 Nos.

EARTHING The rates for earthing items shall also include the following All fixing accessories such as brass, saddles, brass screws, rawl plugs etc. Cutting chases, holes and making good the same wherever required. Effecting adequate and proper interconnections. Use of copper thimbles. Excavation of earth, refilling, watering and ramming and making good as approved in all kinds of soil. All earthing pits shall be interconnected. Earthing shall be as per IS-3043-1987

Supply & Installation of Maintenance Free Copper Bonded Earthing Rod of 3 Mts Length and 17.2 mm dia (Copper Bonding shall be of minimum 250 microns ) along with Ground Enhancing Compound required to fill up the excavated earth, to absorb the surrounding moisture and ensure dissipation of any lightning / fault current (40 Kg required per earthing), supplied with rod to conductor connector.

Providing, laying in ground or on walls Copper/ GI Strips as earthing strips From Equipment/ Panels/ DB’s, switchboards up to the earth pit as per instructions of Engineer in charge.

GI Strip 50 x 6 mm ( Transformer & DG body , Main LT panels & Meter Panels & along Cable trays)

GI Strip 25 x 3 mm

8 SWG G.I. Wire ( For DBs)

LIGHTNING PROTECTION AIR TERMINATION Supply, Installation, Testing & Commissioning of Controlled Early Streamer Emission (CESE) lightning conductor, equipped with a tinned copper central pick up rod, full electrical continuity between the tip and the earth point, fully autonomous (no battery, no external power supply required), collect ambient energy through a lower series of electrodes, timing of the streamer emission controlled with an electronic device that detects the lightning and triggers a streamer (3.5 KV and 20 A), manufactured as per NFC 17-102 with dedicated tester available for maintenance purpose, tested in high voltage laboratory (CPRI) as well as in real lightning conditions including all necessary accessories etc. complete. Radius of Protection at 5 Mts height with Level II Protection - 100 m

GI ELEVATION POLE Supply & Installation of GI Elevation pole with a reducer to fix the LA unit, Base Plate, Clamps and all required fixing accessories.

DOWN CONDUCTOR Supply of 32 X 6 mm G.I Strip

Supply of Test Clamp to connect the down conductor to the earth termination and disconnect the down conductor from the earth termination for regular checks of the earth termination resistance value.

PERFORMANCE RECORDING EQUIPMENT Supply & Installation of Lightning Flash Counter, electronically controlled, register every strike between 1000 A to 100 KA for a 8/20 microsecond peak current, tested in High Voltage Laboratory (CPRI) etc. complete

CABLE TRAYS Supply and providing MS Ladder or perforated type cable trays factory fabricated out of 14 G sheet steel, channel size 75 x 15 mm, spaced at 250 mm interval, supporting angle frame at every 2 m, bottom , angle fasteners, anchor grip bolts, synthetic enamelled painting including primer, etc. The tray shall be suspended from ceiling using anchor bolt and angle iron supports or mounted from wall. The rate shall include all accessories like bends, elbows, tees, coupler plates, etc., which will be measured as linear measurement and fixing accessories.

450 x 50mm Perforated Type Tray

300 x 50mm Perforated Type Tray

150 x 50mm Perforated Type Tray

75 x 25 mm Perforated Cable Tray

Point Wiring

Supplying and erecting steel tubular swaged type welded pole with upper portion hydraulically bent swan neck, 165.1 x 139.7 x 114.3 mm dia with 4.5 x 4.50 x 3.65 mm thickness (5 + 2 + 3 m) respectively (net vertical height 9 m.) total length 10 m long with base plate in provided foundation.(weight 156.75 kg) as per specification No. OH-PL/STP (AS PER iTEM 8.1.16 OF CSR)

Supplying and erecting LED street light fitting suitable for above 75-90W lamp, including lamp, with PF>0.95 class IP 65 and above Housing of pressure die cast alluminium alloy and heatsink extruded alluminium complete per specification No FG-ODF (As per Item 2.9.7 of CSR)

Supplying & erecting PVC armoured cable 2 core 10 sq mm aluminium conductor with continuous 5.48 sq mm (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (As per Item 7.1.4 of CSR)

Supplying PVC insulated PVC round sheathed 2.5 sq.mm (50no.x0.25mmdia.) 3core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV (As per ITEM 1.3.30 of CSR)

Supplying & erecting FRP box of size 250mm x 200mm x 100 mm., 2.7 mm thick complete on pole as per specification No. CB-SB (As per Item 7.8.9 of CSR)

Supplying and erecting pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification No. EA-EP (As per Item 9.1.4 of CSR)

Supplying & erecting Siemens type brass cable glands for 3 to 4 core 6 sq mm /2 to 4 core 10 sq mm for PVC armoured cable as per specification No. CB-GL (As per Item 7.7.2 of CSR)

Supplying & erecting crimping type copper lugs for cable upto 16 sq mm complete as per specification No. CB-CL/CU (As per Item 7.9.1 of CSR)

Supplying & erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification No. CB-CIP (As per Item 7.8.1 of CSR)

Supplying & laying (including excavation) 15 cm dia half round RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet). (As per Item 7.6.6 of CSR)

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet). (As per Item 7.6.6 of CSR)

Providing cement concrete foundation including excavation for the poles 60 cms. x 60 cms. x 1.5 mtr. deep in 1:3:6 cement concrete (20 x 25 mm. stone metal) and 45 cm x 45 cm x 45 cm /45 cm. dia. x 45 cm. height plinth duly plastered and with necessary curing and finishing in an approved manner. (for 8.5 to 9 m poles) (As per Item 16.3.2 of CSR)

Price should be quoted on the basis of free on road (FOR) destination and including all taxes (GST) / Duties / freight / insurance / packing and forwarding, Loading and Unloading, Civil work. Price should be firm and free from escalation