CA NO. CWE SGNR - 06 OF 2020-21 SPECIAL REPAIRS TO BUILDING NO. P-801 (A to F), P-766 (A to F) AND P-806 (A to F) AT MILITARY STATION FARIDKOT

Amount

Taking down of chowkats or frames n.exc 1.5 Sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down of chowkats or frames exc 1.5 Sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

M&L for Taking down & Refixing of Shutter in same opening of any description exc 1 sqm nexc 2Sqm each complete all as specified and directed by Engineer-in-Charge.

M&L for Taking down Shutter of any description exc 1 sqm nexc 2Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engineer-in-Charge.

S&F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engineer-in-Charge.

M&L mild steel framed work of Fe-290 (Gde E-165) as in grills/guard bars shouldered with steel windows/ventilators frames. Cooler stand, ladder etc including redoxide primer coat complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood plain framed pannel shutters (any number of pannels) with pannels of timber flat on both sides (feather edges) or of vaneered partical board medium desnsity, wood partical board with commercial face veneers fitted to chowkats complete all as specified and directed by Engr-in -Charge

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and directed by Engineer-in-Charge.

S&F pressed steel rectangular frames for built in cupboard doors, made out of mild steel sheet 1.25mm thick with girth of frame 185mm including MS rawls plugs and fixing 100mm long butt hinges medium weight cold rolled mild steel etc including two coats of synthetic enamel paint over a shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charge

S&F pressed steel door shutters including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitered angle, one No of locking arrangement two nos Handle etc and applying two coats of synthetic enamel paint over a shop coat of zinc chromate primer all as per Godrej pattern complete all as specified and directed by Engr-in-charge Note : (i) Measurement of door shutter shall be taken as exact size of cupboard opening (excluding frame and folded/ turned up portion) (ii) Stiffeners of 150mm girth and height equal to height of shutter made to shape as directed by Engr-in-charge. cost of these stiffeners shall be deemed to be included in the unit rate quoted for door shutters and no extra measurement/payment shall be made for the same.

M&L block boards 18/19mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on one face fixed with screws to frame-work complete all as specified and directed by Engineer-in-Charge.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed by Engineer-in-Charge.

S&F sheet glass of 3mm,ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge.

S&F in repair Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge.

S&F 3mm th Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Solid wood moulded grain printed PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, egdes will be painted to match printed sheets, in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F Factory Made Solid wood grain printed PVC Moduled Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long Aluminium handles cast type anodised complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 125 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation old painted steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new or previously untreated surface of wood or wooden based surfce any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old painted surface of wood or wooden based surfce any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F in repair MS powder coated decorative drapery rod (colour as approved) of 20mm dia approved pattern & design including decorative knobs (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screws & PVC rawl plugs/grips complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:3:6 type C0 using (12.5mm graded aggregate) as in back filling of pressed steel frames, bed blocks, coping, fixing of hold fasts etc including necessary formwork complete all as specified and directed by Engr-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed by Engineer-in-Charge.

S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge

All as per item No 38 above but as in vertical surfaces such as skirting, dados & risers to steps etc complete all as specified and directed by Engineer-in-Charge.

S&F Glazed ceramic coloured tiles with highlighter in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick rendering in CM 1:4 on other than fair face of brick work. (Highlighter shall be provided as directed by Engr-in-Charge) complete all as specified and directed by Engineer-in-Charge.

Machine cut kota stone slab in flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 15mm thick screed bed or bedding layer CM 1:4 for laying finishes complete all as specified and directed by Engineer-in-Charge.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L Granite 20mm thick work (of any type) (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including nosing edges complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete 50mm thick type C2, 1:3:6 using 20mm graded aggregate as in plinth protection/path finishing surfaces even and fair (without using extra cement) complete all as specified and directed by Engineer-in-Charge.

M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15 mm thick in cement plaster 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and directed by Engr -in - charge.

M&L for Rendering 15 mm thick in cement plaster 1:4 on surface other than fair face of brickwork or stone masonry surfaces or on one side of lathing, finished even and smooth without using extra cement complete all as specified and directed by Engr -in - charge.

M&L Rendering 10 mm thick in cement plaster 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparation of newly plastered or unplastered surfaces of wall and applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface over one coat of primer by hand roller complete all as specified and directed by Engr -in - charge.

M&L for complete removal of existing treatment of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of distemper oil emultion white/tinted with a wall care putty finished surface over one coat of primer using hand roller complete all as specified

M&L preparation of newly plastered or unplastered ceiling and applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface over one coat of primer by hand roller complete all as specified and directed by Engr -in - charge.

M&L preparation of newly plastered or unplastered ceiling surfaces and applying two coat of white wash complete all as specified and directed by Engr -in - charge.

M&L complete removal of existing treatment of old decorated surfaces of ceiling by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of distemper oil emultion white/tinted with a wall care putty finished surface over one coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old surfaces of ceiling and applying two coat of white wash complete all as specified and directed by Engr -in - charge.

M&L preparation of newly plastered or unplastered surfaces of wall and applying two coat of cement base paint over one coat of primer complete all as specified and directed by Engr -in - charge.

M&L complete removal of existing treatment such as white wash, colour wash, synthetic enamel paint etc of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of cement base paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. Note :- Curing of surface will be carried out as per Para 15.15.3 of SSR Part-I

Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M&L for RCC 1:2:4 B1 (20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in shelves complete all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge.

S&F MS TMT Bars of 6mm to 8mm dia,cut to length,bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire (annealed) not less than 0.9 mm dia or securining with clip complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry,built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L old size brickwork with fly ash bricks straight or curved on plan exc 6m mean radius wall built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per item No 63 above but except bricks complete all as specified and directed by Engineer-in-Charge.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engineer-in-Charge. (Paymentfor providing grooves shall be made separately).

M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per pecifications and direction of the Engineer-in-charge

Taking up or down 15mm dia GI Tubing and connection including, cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

All as per item No 67 above but 20mm dia complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore GI tubing medium grade with all fittings fixed to walls or laid in floors complete all as specified and directed by Engineer-in-Charge.

All as per item No 69 above but except tubes complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore GI tubing med grade with all fittings fixed to walls or laid in floors complete all as specified and directed by Engineer-in-Charge.

All as per item No 71 above but except tubes complete all as specified and directed by Engineer-in-Charge.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm fancy type chromium plated Angle valve/stop valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm fancy type chromium plated pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, CI 'P' or 'S' traps 100mm & PVC flush pipes 32mm dia including connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified and directed by Engineer-in-Charge.

S&F in repair 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, waste pipe, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

S&F PVC Connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel plate rack 1.25mm thick of size 900x775x250mm made out of 1mm thick stainless steel of first quality complete all as specified and directed by Engr-in-charge

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F swivel shower of PTMT any colour for fixing 15mm pipe (Minimum weight 40gms) with shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour complete all as specified and directed by Engineer-in-Charge.

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed by Engineer-in-Charge.

S&F cast iron or mild steel peg set 175mm to 250mm with hooks fixed to wall complete all as specified and directed by Engr-in-Charge

Dismantling CI/PVC pipe alongwith fittings of 75/100mm dia,below or above GL, laid in floors or fixed to walls jointed in cement mortar and taking out complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bend any radius 110 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F 100mm dia cast iron soil, waste and vent pipe, in any length with or without ears with cement joints laid in trenches, in floors or fixed to walls complete all as specified and directed by Engineer-in-Charge.

All as per Item No 92 here in before but 75mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F in 100 dia CI bends, diminishing pieces or tapers complete all as specified and directed by Engineer-in-Charge.

All as per Item No 94 here in before but 75mm dia all as specified complete all as specified and directed by Engineer-in-Charge.

M&L in repairs CI Floor trap long neck 75 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) etc fixed in repairs complete all as specified and directed by Engineer-in-Charge.

S&F branch pieces, 100mm dia, single (equal or unequal), ordinary of inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge.

S&F branch pieces, 75mm dia, single (equal or unequal), ordinary of inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge.

S&F 75mm cast iron vent cowls complete all as specified and directed by Engineer-in-Charge.

S&F in repair Rotational moulded polythylene 500 capacity water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position including PVC float valve 20 mm bore, high pressure with polythene ball & float & dismantling of old water tank complete all as specified and directed by Engineer-in-Charge.

Demollition of cement concrete in any descriptiion and in any position not otherwise specifically provided for and removing the same complete all as specified and directed by Engineer-in-Charge.

M & L for water proofing treatment to RCC sunken slab as specified below and as directed by Engineer in Charge:- (a) Rendering 15 mm thick in cement mortar 1:3 using water proofing compound on raised vertical surfaces. (b) Cleaning the surface with wire brush / coir brush, removing loose material like dust particles, dirt etc. (c) Creating fillet covering of 50 x 50 mm with polymer modified mortar on the junction of slab and wall (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surface. (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating. (f) Apply second coating of two component modified polymer coating after 72 hrs. (g) Laying concrete 1:4:8 over the coating as per requirement. (h) Joining the sanitary pipes with the waterproofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and sanitary pipe with non shrink cementatious grout. (k) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Make : Dr. Fixit / Fosroc / BASF / STP. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment (iii) WPC shall be measured and paid seperately.

M&L for Rendering 10 mm thick in cement plaster 1:4 with WPC on roof, fair faces of brick work or concrete surfaces all as specified and directed by Engr -in - charge. Note : WPC will be measured and paid separately

Demolition of concrete (unreinforced) in roofs any thicknessincluding plastering leaping (whether full thickness removed or only part thereof ) complete all as specified and directed by Engineer-in-charge.

M&L PCC 1:3:6 type C 2 (40 mm graded aggregate) in roof complete all as specified and directed by Engineer-in-Charge.

M&L for Roof Treatment as specified below and as directed : (a) Cleaning, washing of surface and removing all existing bitumen coatings completely with intense wire brushing or high speed water jet. Surface should be free from any loose paint, dust or grease. (b) All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars. (c) Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water) (d) Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls. (e) Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UV Stable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured (Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm, with paint brush/ roller upto 300 mm on walls. (f) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Make : DrFixit/ Asian/STP Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment .

M&L 40mm thick PCC 1:2:4 type B0 (12.5mm graded aggregate) with WPC in roof complete all as specified and directed Note : WPC will be measured and paid separately. (WPC will conforms to IS: 2645-2003)

Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up drain pipes 150mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed by Engineer-in-Charge.

M&L 150mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed by Engineer-in-Charge.

M&L 150mm bore Concrete bed (PCC 1:3:6 type C2) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in-Charge.

S&F Factory made SFRC (steel fiber reinforcement concrete) manhole cover medium duty 900x450x70 mm thickness incl 2 mm thick flat iron frame all round complete all as specified and directed by Engineer in charge.

M&L for Hard core of broken bricks gauge n. exc 63mm depositing, spred and levelled in layers n.exc 15cm thick watering and ramming to true surface with broken stone boulders complete all as specified and directed by Engineer-in-Charge.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Machine pressed precast conctete interlocking paver block, with grey cement and pigment and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified as directed by Engr-in- Charge

M&L PCC 1:3:6 type C1 (20mm graded crushed stone aggregate) in kerbs, rounded or chamfered on edges, slightly rounded or chamfered angles and throating, (in sides of path/paving) complete all as specified and directed by Engineer-in-Charge.

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as Switches, sockets, ceiling roses, holders, call bells, fan regulators & making good to the disturbed surfaces of walls, matching the colour with existing Surface complete all as specified and directed by Engineer-in-Charge. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable main switches, TPN/SPN and making good to the disturbed walls complete all as specified and directed by Engineer-in-Charge.

Taking down unserviceable submain wiring any size any run with earthing cable and making good to disturbed area complete all as specified and directed by Engineer-in-Charge.

Point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unshathded cable 1100 volts grade FRLS with multistranded copper conductor drawn through concealed / surface in wall / roof/ ceiling surface and its accessories on the surface etc inlcuding PVC rigid concealed conduit suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes 2mm thick galvanized steel pressed sunken terminal boxes of suitable sizes including painted with one coat of red oxide primer all around for mounting of switches, sockets, fan regulators etc covered with 2.8mm thick plastic laminate Hylem / Anchor top cover of required colour fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat of red oxide primer including fixing continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated stranded (Green colour) connected to common earth point dolly for one light point / fan point / exhaust point and call bell point to be controlled by one number one way point switch complete all as specified and directed by Engineer-in-Charge

All as per Srl item No. 123 here-in-before but for one light point controlled by two 2-ways switches, with cables 1.5 Sqmm size complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed by Engineer-in-Charge

All as per Srl item No. 123 here-in-before but for one Switch socket combination 3 Pin 5 Amps 230 Volts point controlled by one switch and wiring with 1.5 Sqmm PVC unsheathed copper conductor cable 1.5 Sqmm PVC insulated earth wire on independent board complete all as specified and directed by Engineer-in-Charge

All as per Srl item No. 123 here-in-before but for bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Ser item No. 123 here-in-before but with 2.5 sqmm cable for 1 No. 16 Amps switch socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor complete all as specified and directed by Engineer-in-Charge.

S&F electronic bell ding dong type, AC 230 Volt single pole complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC Lamp holder suitable for 5 to 20 watt bulb complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED bulb 1 x 10 watt lamp having luminous efficiency warranty 2 years complete all as specified and directed by Engineer-in-Charge.

Supply and fixing complete set of LED tube light fitting 1 x 20 watt (4 feet long) 230 V, surface and wall mounted decorative ultra slim linear LED lighting fixture with enviornment friendly, energy efficient ready to use pack etc with all accessories including connections up with copper conductor wire with suitable size as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing complete set of LED mirror light fitting 1 x 12 watt to 20 watt, 230 volts, including LED lamp with driver complete suitable for fixation on wall with body retrofit corrosion resistant superior finish and without any cracks through holes with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing complete set of LED tube light fitting 1 x 9 /10 watt, 230 V, surface and wall mounted decorative luminaries with high level of durability with high impact resistant and protection with comfortable soft lighting with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

S&F Ceiling rose 3 phase PVC/polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

S&F Sub main wiring with 2 single core PVC FRLS insulated stranded copper conductor cable of size 6 Sqmm and same 6 sqmm for continous earth wire drawn into concealed PVC conduit complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Cost of PVC conduit, conduit accessories and earth wire included in sub main wiring., (b) Three lengths of single core 6 Sqmm cable and suitable size of PVC conduit will be measured as one length)

S&F switch piano flush type single pole one way 5/6 Amps, 230 volts AC supply complete all as specified & directed by Engineer-in- charge.

S&F socket outlet two-in-one, 5 pin, 5 Amp 230 volts AC supply complete all as specified & directed by Engineer-in- charge.

S&F switch piano flush type single pole one way 15/16 Amps, 230 volts AC supply complete all as specified and directed by Engineer-in-Charge.

S&F switch piano flush type single pole two way 5/6 Amps, 230 volts AC supply complete all as specified and directed by Engineer-in-Charge.

S & F bell push flush type 5 Amps 230 volts AC supply complete all as specified and directed by Engineer-in-Charge.

S&F electronic bell ding dong type, AC 230 Volt single pole complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 2 in 1, 5 pin, 15/16 Amps, 230 volts AC supply complete all as specified & directed by Engineer-in-Charge.

S&F fan regulator electronic socket / stepped flush type 5 speed for ceiling fan 1200mm/ 1400mm sweep on the existing phenolic laminated sheet etc complete all as specified and directed by Engineer-in-Charge.

S&F factory made sheet metal enclosure for DB's TPN 440 volts, 4 way with 200 Amps rated bus bar double door for provn on 63/100 Amp MCCB complete all as specified & directed by Engineer-in-Charge.

S&F factory made sheet metal enclosure for double door distribution board with epoxy powder coated surface mounted SP & N 8 way, protection class IP-43 suitable for mounting MCB, conforming to IS-8623, BS-5484 with 200 Amps rated copper bus bar stove enameled dust and vermin proof suitable for working on 240 volts AC supply complete all as specified & directed by Engineer-in-Charge.

Supply and fixing MCCB TPN, 415 volts, 100 Amps with breaking capacity 16 KA including taking down old unserviceable MCCB complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 32 Amp, 230 volts, C Series with breaking capacity 10 KA incuding taking down old unserviceable MCB complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 32 Amp, 230 volts, C Series with breaking capacity 10 KA incuding taking down old unserviceable MCB complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 40 Amp, 230 volts, C Series with breaking capacity 10 KA incuding taking down old unserviceable MCB complete all as specified and directed by Engineer-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel & wiremesh, PCC chamber in cement concrete (1:2:4) type B-1 and CI cover with frame, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. complete all as specified and directed by Engr-in-charge. (Notes :- (i) GI wire upto earth test point/ equipment is included in this item. (ii) Outer edge of earth pit chamber shall be 1 metre away from the outer edge of PCC chamber.)

Taking down carefully ceiling fan any size and refixing only hanging ceiling fan any sweep connecting up including three core copper flexible wire not less than 0.5 mtr for connecting from ceiling rose / connector to ceiling fan complete all as specified and directed by Engineer-in-Charge.

Supply and spread dry fine aggregate sand in trenches for cable cushioning all as specified on both top and bottom of cable incuding ramming complete all as specified and directed by Engineer-in-Charge. Note : For the purpose of payment the punned thickness only measured.

Supplying and laying well burnt clay bricks old size class 'B' laid dry and flat for protection over the cable with equal to the length of cable, complete all as specified and directed by Engineer-in-Charge.

Supply & laying XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm 4 Core in trenches / floors / wall and under road including connecting with suitable aluminium lugs and incuding taking up defective unserviceable cable of the any sizes all as specified and directed by Engineer-in-Charge. Note : Earth work, Sand cushioning, GI pipe and brick for protection to be measured and paid separately.

Supply and fixing LED street light fittings 25 watt LED drawn aluminium housing in grey finish with clear acrylic and cast aluminium pipe mounting attachment including fixing to wall/ on pole including fixing arrangement with suitable galvanized iron pipe 32mm to 40mm bore light grade brackets 1 mtr length bent to shape required including clamps, nuts/ bolts/ washers etc connecting with suitable flexible copper wire of size 23/0.0076 testing as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of MS clamp of size 40mm x 3mm for holding of GI pipe with pole and wall complete with nuts, bolts and washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint all as specified and directed by Engineer-in-Charge.

Supply and fix GI pipe 40 mm bore light grade for protection of cable including provision of clamps, nuts, bolts etc required for fixing pipe along pole / wall / laid under the road / laid under the floor or in trenches complete all as specified and directred by Engineer-in-Charge.

S&F switch bell push button type 6 Amp single pole complete all as specified and directed by Engineer-in-Charge. Cat Part No F 902 for switch and F-919 for Switch frame of Make : SSK or equivalent in Legrand / Hager.

M&L for switch piano flush type single pole two way, 5/6 Amp fixed on laminated sheet top cover (laminated sheet top cover is included in point wiring) complete all as specified and directed by Engineer-in-Charge.

S&F ceiling fan regulator 0-4 steps step 450 W hum free including 6A socket frame and including connections complete all as specified and directed by Engineer-in-Charge. Cat Part No. F 911 for regulator and F-920 for socket frame of make SSK or equivalent in Legrand / Hager.

S&F switch 6 amps 250 V AC one way with ISI mark including 6 amps switch frame complete all as specified and directed by Engineer-in-Charge. Cat Part No F 900 for switch and F-919 for Switch frame of Make : SSK or equivalent in Legrand / Hager.

S&F socket 5 pin shuttered 6A 250 V AC including 6 A Socket frame complete all as specified and directed by Engineer-in-Charge. Cat Part No F 904 for socket and F- 920 for Socket Frame of Make SSK or equivalent in Legrand / Hager.

S&F Switch single pole mini with porcelain Base 16 A 250 V AC with ISI mark including switch frame complete all as specified and directed by Engineer-in-Charge. Cat Part No F 954 for Switch and F-919 for Switch Frame of Make SSK or equivalent in Legrand / Hager.

S&F socket 5 pin shuttered 6A/16Amp 250 V AC i2 in 1 ncluding 16 A Socket frame complete all as specified and directed by Engineer-in-Charge. Cat Part No F 951 for socket and F- 920 for Socket Frame of Make SSK or equivalent in Legrand / Hager.

Supply and fixing LED mirror light fitting 1 x 5 watt including LED tube complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks of through holes. The system wattage of fitting should not be more than 5 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 351 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting 1 x 20 watt including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 1700 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

S&F Decorative wall light fixture made up half cut frosted glass suitable for and including 1 x 9 W LED Lamp with B-22 base as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing lamp holder with1 x 10 watt LED lamp B-22 base complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks of through holes. The system wattage of fitting should not be more than 10 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 351 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

S&F 1 x 10 Watt LED Bulk head luminaries with lamp, holders, 850 lm with an efficacy of 85 lm/w etc complete with accessories pre wired and including connecting with flexible cord 3 core 0.5 sqmm as per specification including taking down old unserviceable light fittings of any type complte all as specified and directed by Engineer-in-Charge.

Supply and fixing Exhaust fan light duty AC single Phase 230 V / 240V 50 Hz of size 300 mm sweep, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including taking down old unserviceable exhaust fan and deposit to MES store yeard complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of Storage water heater 25 ltrs cap vertical mounting AC 230 Volts including connecting cord and plug, safety valve, nuts and bolts, complete including grouting of nuts and bolts complete all as specified and directed by Engineer-in-Charge.

S & F PVC sleeves for connection of conductor to MCB DB any type any size complete all as specified and directed by Engineer-in-Charge.

S&F earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engineer-in-Charge. -------------------------------------------------------------------------------------------------------------- Note : A sum of Rs. 1,08,237.88 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 41 & 42(R) (Schedule of Credit) of Tender document

Marwaha Builders

M/S Yashpaul Gulati