SPECIAL REPAIR TO BLDG NO P-151 OF BHARATPUR LINE AT MIL STN DHARAMSHALA

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as spcified and directed by Engr-in-Charge.

Galvanized, corrugated mid steel sheeting with two corrugation side lap fixed with L type or J type or cranked hooks bolts with grade of zinc coating 275 complete all as specified and directed by Engr-in- Charge.

All as per item No 02 above but refixing only.

Taking down Cement plaster on brick or stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-Charge.

Rendering 20 mm thick on stone surfaces surfaces or other than fair faces of brick or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Rendering 20 mm thick on stone masonry other than fair faces of brick or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Two coats of cement based paint on new plastered surface of walls including preparation complete all as specified and directed by Engr-in-Charge.

Two coats of cement based paint on old plastered surface of walls including preparation complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surface of walls and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surface of walls and applying one coat of white wash complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 sqm but not exceeding 4 sqm each and removing complete, all as specified and as directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) area not exceeding 1.50 sqm and removing complete, all as specified and as directed by the Engineer-in-Charge.

2nd Class hard wood (Sal/Hollock) plain, solid, straight chowkats or frame wrought, framed, rebated on the solid, rounded or chamfered put together with glue, pinned at joints with one or more rebates, complete all as specified and as directed by the Engineer-in-Charge.

2nd Class hard wood (Sal/Hallock), Plain framed, panelled 35mm thick shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, Complete all as specified and as directed by the Engineer-in-Charge.

30mm thick 2nd class soft wood glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) supplied and fitted to chowkhats complete, all as specified and as directed by the Engineer-in-Charge.

Mild steel galvanised wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or wire staples or wooden beads complete (fixed in repair) all as specified and directed by Engr-in-Charge.

Mild pressed steel handles, 150mm size oval type stove enamelled black, complete, all as specified and as directed by the Engineer-in-Charge.

Mild Steel tower bolts 150mm size stove enamelled black complete, all as specified and as directed by the Engineer-in-Charge..

250mm long, mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floors & paving not exceeding 15 cms thick (below or above ground level), complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-7.5, (nominal mix), type D-2 (using 40mm graded crushed stone aggregate) as in foundation,filling & mass concrete including necessary form work complete all as specified & directed by Engr-in-Charge.

Mirror polished machine cut kota stone slab flooring, 20-25mm thick, over 15mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

All as per item no 22 here-in-above but as in riser of steps, skirting, dado and pillar over 10mm thick bedding layer in CM 1:3.

75mm Plain cement concrete M-15, type B-2 (using 40mm graded crushed stone aggregate), as in floor/pavings finished even and smooth without using extra cement and directed by Engr-in-Charge.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc.0.50 sqm in each pane complete, all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings dressed stone work and precast concrete articles, complete all as specified and directed by the Engr-in-Charge.

Walling of random rubble stone masonry, uncoursed, brought up to courses, well bonded, bedded and solidly hearted and built in cement mortar 1:6, complete all as specified and directed by the Engr-in-Charge.

All as per ser item No 28 here-in-before but except stone.

Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 including flush pointing in same mortar, complete all as specified and directed by the Engr-in-Charge.

RCC , M-15, type B-1 (using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, coping and the like, complete all as specified and directed by the Engr-in-Charge.

Chequered cement concrete tiles, machine pressed glossy finish (heavy duty) of size 30cmx30cmx25mm thick with grey cement and pigment set jointed & pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6 complete, all as specified and directed by Engr-in-Charge.

Plain Cement concrete, M-7.5, type D-2 (using 40mm graded crushed stone aggregates) as in sub base, complete all as spcified and directed by Engr-in-Charge.

Framed work for fixing of steel sheeting or other cover such as eaves board to be prepared for hanging or sliding with and including either hook and hinger or steel hanging specified and as directed by Engineer-in-Charge.

Plain mild steel sheeting, 0.63 mm thick in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275complete all as specified and directed by Engr-in-Charge.

50mm thick plain cement concrete, M-10, type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection complete, all as specified and as directed by the Engineer-in-Charge.

Dismantling of wrought iron mild steel work of any description, complete all as specified and directed by the Engr-in-Charge.

Rolled section as in main and cross beams, hip and jaqck rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde E-250) quality A, complete all as specified and directed by the Engr-in-Charge.

Rolled MS wk as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-410W (Gde E-250) quality 'A', complete all as specified and directed by the Engr-in-Charge.

Mild steel work as in in rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including emberding in concrete and screwing etc, wind ties for roof including securing bolts, etc or similar small articles conforming to grade Fe-290 grade E-165, complete all as specified and directed by the Engr-in-Charge. Note:- Flat iron for wind ties shall be of size 40x4mm.

Two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces including prepration of new steel surface, complete all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of red oxide primer including preparation of old steel surface of any description excluding 10cm width or girth, complete all as specified & directed by Engr-in-Charge.

Machine presseed precast concrete interlocking paver block of any shape and size conforming to IS 15658-2006 of 60mm thick of M-35 grade with grey cement and pigment to match the shade of paver blocks, complete all as specified and directed by Engr-in-charge.

Supply and laying of fine aggregate (sand) for cushining under interlocking tile complete all as specified and directed by Engr-in-charge.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc including removing material for taking credit ( credit shall be recovered as per credit Schedule attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly in existing CI/ wooden/ MS box covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point/ fan/exhaust fan point/ bell point etc controlled by one, one way switch, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Eye/ bottle thimbles shall be used for connection in switches/ sockets & MCB's in DB's without any extra cost. (ii) Electric rewiring should be donein proper color coding i.e. red for phase, black for neutral and green for earth.

All as per item No 46 here-in-above, but for one 3 pin socket outlet 5 Amp on the independent board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 46 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and as directed by Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp & 15 Amp, flush type complete all as specified and as directed by Engineer-in-Charge.

Switch piano, flush type, single pole, one way 15 Amp complete all as specified and as directed by Engineer-in-Charge.

Switch piano, flush type, single pole, one way, 5/6 Amp complete all as specified and as directed by Engineer-in-Charge.

Ceiling rose, surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all as specified and as directed by Engineer-in-Charge.

Supply and fix (in replacement) for sub main wiring two single core PVC insulated and unsheathed cable with 4 Sqmm multi -strand copper conductor drawing in PVC casing caping with 25 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as specified and as directed by Engineer-in-Charge.

Supply & fix (in replacement ) of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar complete all as specified and as directed by Engineer-in-Charge. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job. Make: Havells/ Legrand/ ABB

MCB, SPN, 40 Amp, breaking capacity 10 KA, complete all as specified and as directed by Engineer-in-Charge.

MCB, SP, 6-32 Amp complete all as specified and as directed by Engineer-in-Charge.

Universal batten for LED Tube suitable for indoor applications tube light fitting 4 Ft, 1x18W complete all as specified and as directed by Engineer-in-Charge. Make: Haverlls Cat Part No. reGalBattent5uPtox1x18WdsBsWH or equivalent in Philips/OSRAM/Bajaj

LED tube light with very high efficiancy suited for installtion in existing batten all as specified and as directed by Engineer-in-Charge. Make: Havells CAT Part No. CrYstal1213t8dstl18Wled865sGlass or equivalent in Philips/OSRAM/Bajaj.

1x25 watt LED Bldg security light fittings with lamp pressure die cast, housing with epoxy powder coated dark graphite gery colour finish, prismatic polycaqrbonate cover with individuaal LED lenses with GI pipe 1.5 Mtr length, clamps, nuts, bolts complete all as specified and as directed by Engineer-in-Charge. Make: Cromption Cat Part No. LSTS25CDILED or equivalent in Philips/Bajaj.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frame 25x25x6mm and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and shown in EP-3 of SSR Part-I & as directed by Engr-in-Charge.

Service wire 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured and overall PVC sheather in service connections suspended by insulting hangers not more that 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 10 aqmm 2 core, complete all as specified and directed by Engineer-in-Charge. .

Excavation in trenches, not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth and getting out complete, all as specified & directed by Engr-in-Charge.

Returning, filling in (soil), inclding spreading, levelling, watering and well ramming in layers not exc 25 cm thick in any type of soil complete all as specified and directed by Engr-in-Charge.

Removing of excavated soils to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.50mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I laid before and after laying of cables, complete all as specified & directed by Engr-in-Charge.

Sub class 'B' bricks, old size, laid in trenches as cable covers complete, all as specified & directed by Engr-in-Charge.

GI tubing, light grade,40mm bore with all fittings laid in trenches or under road crossing or fixed along walls /poles/pipes as protection pipe with clamps, nuts, washer bolts (where necessary) as per reqmt of site complete all as specified & directed by Engr-in-Charge.

surinder kumar jindal bros

KISHAN CONTRACTOR