CONSTRUCTION OF NEW HOSPITAL BUILDING (G+4) IN THE CAMPUS OF PATNA HIGH COURT

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Extra for every additional lift of 1.5 m or part thereof in :

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Centring and shuttering including strutting,propping etc. and removal of form for

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of deshutering and de centring at all levels over a height of 3.5 m ,for every additional height of 1 metre or part thereof (Plan area to be measured)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Thermo-Mechanically Treated bars TMTC-500-16mm dia.

Thermo-Mechanically Treated bars TMTC-500-20mm dia.

Thermo-Mechanically Treated bars TMTC-500-25mm dia.

Thermo-Mechanically Treated bars TMTC-500-32mm dia.

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

All work above Plinth level upto floor V Level.

Add for using extra cement in the items of design mix over and above the specified cement content there in.

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

750 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loadingplatform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.

Initial test

Routine test

Brick work with bricks of class designation 100A in foundations andplinth in :

Extra for Brick work in superstructure above plinth level upto floor V

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send)

Extra for providing and placing in position 2 Nos, 6 mm dia , MS bars at every third course of half brick masonry (with F. P. S. bricks)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying Autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand).The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Area of slab upto 0.50 sqm

Area of Slab over 0.50sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble/granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform. Vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing,moulding and polishing of cut edges etc. complete.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glas excluded)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge

Providing and fixing to existing door frames.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing fire resistant door frame of section 50 x 60mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in-charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120minutes of fire resistance both integrity & radiation control (EW120)

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS: 2095: part I

Providing and fixing approved brand and manufacture SS 304 grade D type 1200mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing Glass door Corner Lock prepared for Euro Profile cylinder (EPC) single throw bolt projection 20mm with both side key operation and lock key per plate SS finish DORMA US10 or equivalent complete as per direction of Engineer-in-Charge.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type, 22mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade SS 304 grade Mortise Dead Lock with 60mm Backset fixed fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 150mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete asper the direction of Engineer-in-charge.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Toilet Cubical Providing and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12 mm thick solid compact laminate panels Finish of the compact laminate should be raw silk which include doors, pilasters and intermediate panels finished with approved texture/shade as per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless Steel (Grade 316) as per manufacturer's specifications and EIC instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs.

Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coar of approved steel primer, welded and bolted including special shaped washers etc. complete:

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand )

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3 (1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18mm thick gang saw cut Granite stone work for wall lining, backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortor with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Size of Tile 60x60 cm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600 x 600 mm.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm(avearage) thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

metre

Extra for Granite stone flooring in treads of steps and risers using single length up to 2.00 metre .

Providing and fixing Vinyl flooring of 2mm thick PVC flexible, homogeneous antistatic calendared compacted floor covering, minimum weight 3120 g/m2 in minimum sheet of size 2mtrs. x 20 mtrs. approved pattern & colour combination with PUR Protect or equivalent surface treatment having wear minimum resistance of ≤ 4.0mm3 as per EN 660.2 and wear group Group P as per EN-649 and should have a minimum residual indentation of <0.03mm confirming to EN-433. The laid flooring should have non- directional design, colour dyed as a raw mixture to ensure even colour throughout the thickness and its surface should be densely compacted for improving wear and ease of maintenance with Anti-bacterial and Fungicidal properties. The laid flooring shall confirms the fire rating B1 class as per EN 13501-1. The floor finish should terminate at the room perimeter passing over a concealed cove former and continuing up the wall for 100mm. The joints in the flooring should be sealed by using a PVC welding bar of matching colour to be supplied by the manufacturer, using a hot air gun for fusion of welding bar with flooring and self levelling required underneath with all accessories cove etc.

Providing and applying 1.25mm thk Vinyl based Anti-microbial wall covering over smooth surface including fixing with adhesive complete in all respects.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately).

12mm cement plaster of mix :

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

6 mm cement plaster to ceiling of mix :

18 mm cement plaster in two coat under layer 12 mm thick cement plaster 1:5 (1 cement: 5 course sand) and a top layer 6mm thick cement plaster 1:3(1 cement: 3 coarse sand finiished rough with sponge

Extra for plastering exterior walls of height more than 10m form ground level for every additional height of 3 m or part there of

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Colour washing such as green, blue or buff to give an even shade

Finishing walls with textured exterior paint of required shade :

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

Providing & fixing Geo-synthetic fibre mesh of minimum 300 mm to be used at junctions of brick walls with RCC members before plastering on the inner and outer sides of the junctions. etc. complete as specified in drawing and as per the Direction of Engineer-in-charge.

DRY CLADDING Providing and fixing dry cladding upto 10 metre heights with 30 mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and / or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-Charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately.)

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square / rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of MS brackets / lugs of angle iron / flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps / pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineer-in-Charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-Charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid.)

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size,adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture,diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is nclusive of all materials & labours involved except scaffolding).

GRC JALI Providing and fixing 'Unistone', 'Sanderson' or 'Birla white' Glass Reinforced Concrete (G.R.C) ornamental Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness (Border 40-50mm thick & Internal Member 25-30mm thick) and shade. The Screens should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’ or 'Birla white', White Quartz fine graded seived Silica Sand, Alkali Resistant Glass Fiber manufactured by 'NEG Japan, Owen Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Karochem’ or equivalent, Polymers manufactured by ‘Nova Polychem’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘Phenochem industries or equivalent. The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 12 N/mm2 for tests done on 28 days cured samples. The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e., R.C.C, Masonry work or Red oxide Primer -paint or Epoxy primer -paint treated mild steel. The fixtures, fasteners and self tapping screws to be used for dry fixing should be of HP/KLIMAS. The quantity of fasteners or self tapping screws shall be calculated in accordance to the weight of Screens and actual site fixing conditions. If there will be requirement of Joint filling, then Elastomeric exterior grade paintable PU Sealant will be used. For final finishing of Screen one weather shield exterior grade water based diluted paint coat will be done if required. Vendor shall submit shop drawings of same, the drawings to be duly approved from Engineer in charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing Single Glazing 6mm thick high-performance glass panes ET 125 clear cosmos, nontempered, glass of approved make complete in all respects as per direction of the Engineer-in-charge. all complete as specified in drawing and as per the Direction of Engineer-in-charge.

Filming shall be done on Glass doors wherever required as per directions of Engineer-in-Charge. Filming shall be 30-35 micron (minimum) thick 3M, Garware or equivalent make non reflective matte, frosted/horizontal strips, scratch resistant, high performance resin coated polyster film on the glass surface.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions. (ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying broken AAC Block in sunken portion of W.C. & kitchen. These broken Block mixed with cement mortar 1:8 ( 1 cement : 8 coarse sand) laid and compacted properly including supply of labour, material, and tools and plant etc. as per instruction of Engineer-in-charge.

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls and slabs.

With average thickness of 120 mm and minimum thickness at khurras point to be 6..

Grading roof for water proofing treatment with

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement:2 coarse sand:4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3(1 cement::3 coarse sand)as per standard design

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000mm length and L-hape level adjuster of size 85x25x2 mm, spaced

Providing & fixing access panel is made out of Moist Bloc (Moisture Resistant) board for opening 600 x 600mm of thickness 12.5mm. All edges of the panel are reinforced with aluminium profiles and corners are guarded with stainless steel 304 grade clips to increase strength and prevent damages. complete in all respect as directed by Engineer-in-charge.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the rchitectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS74,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface #2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and fixing 300mm wide 1mm thk grade-304, SS Kick plate over flush door with suitable adhesives, screws etc. all complete as per direction of Engineer-In-Charge.

STRETCHER GUARD Providing and fixing Handrails having vinyl snap-on cover(lead free) of 2mm thickness and aluminium retainer of 2mm thickness that shall be fabricated from 6063-T5 aluminium. Dimensions to be of 110mm height x 41mm gripping diameter which has a oval gripping surface II.. The system shall resist an impact of 45.5 ft-lbs as per ASTM F-476-84. The rigid vinyl shall not support fungal or bacterial growth inaccordance with ASTM G-21 and G-22. The system shall also conform to class A fire rating and ASTM D-543 for chemical and stain resistance. It includes Molded end returns and mounting brackets..all complete as per direction of Engineer-In-Charge.

CORNER GUARD Providing and fixing Corner Guards having vinyl snap-on cover(lead free) of 2mm thickness and aluminium retainer of 2mm thickness that shall be fabricated from 6063-T5 aluminium. Dimensions to be of 51mm x 51mm wings and 90 degrees angle. II. The rigid vinyl profile shall resist an impact of 30.2 ft-lbs/inch as per ASTM D-256-90b and shall not support fungal or bacterial growth inaccordance with ASTM G-21 and G-22. The system shall also conform to class A fire rating and ASTM D-543 for chemical and stain resistance. It includes Top Caps. all complete as per direction of Engineer-In-Charge.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade 'A' sealing compound.

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of/and manure before and after flooding trench with water (encluding cost of imported earth,sludge or manure).

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks will be reduced by 20% for payment).

Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of l.S. designation 20 mm

Screened through sieve of l.S. Designation 16 mm

Screened through sieve of l.S. designation 4.75 mm

Fine dressing of the ground

Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately).

Mixing earth and sjudge or manure in porportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2;1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water,dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately):

Holes 60 cm dia, and 60 cm deep.

Holes 45 cm dia, and 45 cm deep.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Mimusops elengi (Maulsri) of height 180-195 cm., well developed with thick stem in big in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Saraca indica (Sita Ashok) of height 105-120cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Syngonium golden of height 30-45 cm. with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 60-75 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum splendens of height 30 cm to 45cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Stone chips (354 KM from Pakur by Rail + 35 km By Road )

Coarse sand (Lead 1+34km ) From Koilwar

Bricks local 8 KM (7 km Pucca +1 km )

Local sand (1 km kutcha+2 km pucca)

Cement

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting,of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover,and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including ntegrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing Differecially abled toilets including Wash basin, Water closet,Cistern, grab bars & hand rails etc. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. For physically handicap person consisting of;

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade as per Architect.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and Fixing central hole C.P. brass Sink Mixer including cutting and making good the walls wherever required complete in all respects as per direction of the Engineer-in-charge

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT Bottle Trap for Wash basin, Sink and Urinal.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. brass toilet paper holder.

Providing and fixing Health faucet with 1 metre long Flexible Tube and CP wall hook with PVC & SS Screws including cutting and making good the wall wherever required complete as directed by the Engineer-in-charge.

Providing and Fixing straight / offset type flexible single body push fit type WC pan connector with inlet ring and integral single mould sealing fins made of flexible EVA body to be fixed with manufacture supplied grease, including rubber bush / adaptor for use with C.I pipe as supplied with the pan connector complete as directed by Engineer-in-charge.

Providing and fixing C.P cast brass Double coat hook as approved with C.P. brass screws complete as per instructions of the engineer-in-charge.

Providing and fixing Electrically Operated Hand Drier to be operated with 220 volts single phase, with fully hygienic condition, with all accessories including cutting and making good the walls wherever required.

Providing and fixing testing and commissioning of storage type water heater (Geyser) (A. O. Smith make or equivalent) with automatic thermostatic control electric element, pressure release valve, M.S. nuts and bolts etc. conforming to IS: 2082, including cutting holes & making good the wall wherever required complete in all respects.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing automatic sensor faucet for cold water, for wash basin complete in all respect including basin mounted auto tap, with infrared sensors with solenoid valves for cold water with electronic circuit and necessary accessories including cutting and making good the walls and floors as per requirement.

Supply of 150 litre/ hr. cooling and storage capacity,fully stainless steel electric storage type water cooler (Blue Star model No. SDLX 15150 or equvalant) with inlet hose connection inbuilt float valve. 2 Nos. outlet foucet, drain tray with waste and pipe up to floor trap heavy compressor and wire up to socket, 3 pin plug etc complete in all respect

Providing and fixing CP brass single lever telephonic wall mixer of quality & make as approved by engineer in charge..

Providing and fixing PTMT towel ring Trapeoidal shape 215 mm long 200 mm wide minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

75 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

100 mm dia. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree.

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing double equal plain junction of required degree.

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree :

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing double unequal plain junction of required degree :

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single unequal plain junction of required degree :

100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing terminal guard :

100 mm dia. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.

100 mm dia SS 304 grade coupling with EPDM rubber gasket

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work.

100 mm diameter pipe

75 mm diameter pipe

Providing and Fixing 32 mm dia G.I. pipe complete with G.I. Fittings and clamps, including cutting and making good the walls etc.

Providing and Fixing 40 mm dia G.I. pipe complete with G.I. Fittings and clamps, including cutting and making good the walls etc.

Providing and Fixing 50 mm dia G.I. pipe complete with G.I. Fittings and clamps, including cutting and making good the walls etc.

Painting of 32 mm dia G.I. Pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

Painting of 40 mm dia G.I. Pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

Painting of 50 mm dia G.I. Pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

Providing and fixing G.I. Inlet fittings with maximum 3 inlets 32,40 & 50 mm size fabricated from 100 mm dia G.I. pipes and welded G.I. sockets, fixed to C.I. Trap with lead caulked joints and set in cement concrete(1:2:4) complete as directed by Engineer-in-charge.

Providing, fixing, testing and commissioning of UPVC rain water pipes (IS : 4985-1983 class-III ) including injection moulded fittings (heavy duty) (plain or door) e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site [ Terrace Rain Water Downtake Pipe].

Providing, fixing to the inlet mouth of rain water pipe PVC grating / Jali of following size including all fitting and accessories including civil work.

Providing and fixing in position stainless steel cockroch trap consisting of 0.45 mm thick inner and outer cup and 1.00 mm thick top grating (Jali) with ring to be fixed inside C.I. or uPVC ‘P’ traps with cement concrete. (For Kitchen )

Providing & fixing 1 mm thick stainless steel grating with rim of approved design including setting in floor with cement mortar. (For Floor Drain)

Providing and fixing trap of self cleansing design with screwed down or hinged with or without vent arm complete, including cost of cutting and making good the walls and floors.

100 mm inlet and 100 mm outlet

Hubless Centrifugally cast (spun) Iron pipes epoxi coated inside & outside S&S pipe IS: 15905

Providing & fixing rain water `Khurras' size 45 x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 Cement: 2 coarse: 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x1m x400 micron, finished with 12 mm cement plaster 1:3 (1 Cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and Fixing G.I. Reducing elbow of 100 x 50 mm in cement concrete 1:2:4 at all levels for floor drains (exlcuding cost of grating) for connection to floor traps in sunken portions, complete as per drawings and as per approval of the engineer-in-charge.

Providing and fixing 100 mm dia cast brass cleanout plug / floor cleanout with suitable insert keys for opening, male threaded joint with G.I. socket caulked to spun soil pipe including cost of joint etc.complete as directed by Engineer-in-charge..

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc.(Riser pipe)

40 mm dia, nominal bore

50 mm dia, nominal bore

Providing and fixing forged brass nickel plated lever operated ball valve of full flow with forged brass hard chrome plated ball with min. working pressure of 25 Kg/cm2. Lever should be anti rust coating, complete in all respects.

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

Providing and fixing thermal insulation over water pipes exposed in Toilet, shaft & technical terrace with approved equivalent thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber having density of 60-90 Kg/m3 over pipes of following sizes including all required accessories complete as per manufacture's specifications and finishing mechanical protection with 2-3 coat of hardener paint complete.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50 mm dia

65 mm dia

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

25 mm nominal bore

Construction brick masonry chamber (for Housing Lawn hydrant) Garden Hydrant with 75 class designation brick work in cement mortar 1:5 (1 cement : 5 find sand) for valve, with CI surface box 100 x 100 x 75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

300 x 300 x 500 mm deep With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main.

25 mm nominal bore

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

80 mm dia nominal bore

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round HDPE & RCC pipes including bed concrete as per standard design :

150 mm Dia.

200 mm Dia.

250 mm Dia.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50 m. All Kinds of Soil

Pipes, cables etc., exceeding 80mm dia but not exceeding 300mm dia

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg). With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 120 x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing Brick Masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design. External surface shall be finished with 15mm thick cement plaster 1:6 (1 cement : 6 Coarse sand) as per side conditions. 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type Manhole 0.91 internal dia with F.P.S. Bricks class designation 75, depth beyond 0.91 m to 1.67 m

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :: 180 x 150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) with precast R.C.C. vertical grating complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete .

For pipes 250 to 300 mm diameter

Description

1239/Class -II of IS: 3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground )

200 mm. dia (wall thickness = 6.3 mm)

150 mm. Dia

100 mm. Dia

80 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (For Plant Room piping/Vertical Riser/Downcomer/Floor )

25 mm. Dia

32 mm. Dia

40 mm. Dia

50 mm. Dia

65 mm. Dia

80 mm. Dia

100 mm. Dia

150 mm. Dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal / Stainless Steel cap and chain as required :

Single Headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single Headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50 mm. Dia

80 mm. Dia

100 mm. Dia

150 mm. Dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required.

150 mm. Dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

150 mm. Dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.

Gun metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required.

2 way-100 mm dia M.S. Pipe (For UG Tank)

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories.

Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

150 mm. Dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Supply, installation and testing of cylindrical type flanged air cushion tank, 250 mm dia, 1200 mm long and of thickness 8 mm M.S., suitable supporting legs with MS plate of size 75x75x5 mm at the bottom and grouted in CC foundation. The air cushion tank shall be provided with air release valve, stop cock, safety valve, pressure gauge, 25 mm dia drain valve, tested to min 25 Kg/cm2 complete including painting with synthetic enamel paint of approved shade with all accessories as per direction of the Engineer-in-charge. (For Risers)

Providing & fixing air release valve with forged brass body full way ball valve type isolating valve, flanges / union, suitable for sprinkler / wet riser / down comer system with all necessary connections complete in all respects.

25 mm dia air release valve

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing & Fixing of MS door made up of 16 gauge MS Sheet capable of accommodating fire hose reel, landing valve, hose pipes, fittings, 1 No. CO2 & 1 No. Dry podwer type portable fire extinguishers & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with one coat of primer & two coat of finished stove enamelled post office red colour paint & "FIRE HOSE" written on front. (Approx. size of door: 2100 mm Height, Width of Door as per Shaft Size)

Providing and fixing hose cabinet of size 750mmx600x250mm made of 16 gause thick MS sheet with 4 mm thick float glass doors in front painted "FIRE" in red paint i/c recessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos. 15 mtr. long hose pipe. 1 no. brach pipe mounted on wall or raised brick platform & duly painted with post office red externally and white internally with synthetic enamel paint complete in all respects for external hydrant. as directed by Engineer-in-Charge.

Supply, fixing, testing and commissioning of screwed type brass / bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 & spindle AISI 410) with setting & gland of superior quality having minimum working pressure of 16 kg/sqcm.

25 mm Dia

Providing and fixing 25 mm dia inspection & testing assembly with gun metal ball valve, gun metal sight glass ,Reducer ,union, G.I PIPE. connection to drain pipe/riser.

Supply, fixing, testing & commissioning of cast iron body and brass/bronze working parts, UL listed installation control valve assembly, suitable for hydrostatic test pressure 21 kg/sqcm, complete with Hydraulic Alarm motor & hydraulically driven mechanical gong bell to sound continuous alarm when sprinkler system activates, butterfly valve, alarm valve, test valve, pressure gauge, emergency releases, pressure switch, 50 mm dia drain valve, flanges, gasket etc. to complete the system as required, as per manufacturers specifications.

150 mm diameter

Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect.(75 mm OD x 63 mm OD)

Providing and Fixing of CO2 (Carbon Dioxide) based Portable Fire Extinguisher I.S.I. Marked, Valve shall be to IS 3224 Marked, PESO Approved Cylinder and shall be IS 7285 Marked on Body, fitted with High Pressure Wire Braided Hose & Flat Horn with Diffuser, fixed to wall with brackets including all necessary accessorises, IS 15683:2018 Marked as per the directions of Engineer-in-charge.

Capacity 4.5 kg. (IS : 15683:2018)

Providing and Fixing of Dry Chemical Powder based Portable Fire Extinguisher, filled with DCP (ABC) MAP-90% (Mono-Ammonium Phosphate) Powder, Stored Pressure Type, UGTS Pressure Gauge, CE Marked Valve with NRV, fitted with EPDM Rubber Hose, fixed to wall with brackets including all necessary accessorises, Applicable on Class A,B & C and Electrically-Started-Fire, IS 15683:2018 Marked as per the directions of Engineer-in-charge.

Capacity 6 Kg (IS : 15683:2018)

Supply & fixing of 4 nos. G.I. round bottom fire buckets of 9 liters capacity filled with sand including proper supporting / mounting arrangements in MS angle iron frame, painted by fire red colour over two coats of red oxide paint and written with white paint "FIRE" complete in all respects as per the directions of Engineer-in-charge.

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc.

Supplying & fixing of retro reflective sign plates of required size. The plate made of High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film/High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T Reflective tape of same make duly plotter cut, of approved color, letters (single side) in white colour, to be pasted on 3mm thick ACP sheet of make Alstone / Alstrong / Eurobond / Alucobond or equivalent etc. as per drawings. The sign boards shall fixeed on wall/ roof duly fixed with rawls plugs stainless steel srew/ double side tape 3M make/ SS chain of required size of required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of 18 gauge Stainless Steel plates with water jet cutting of grade 304 etching (engraved)signage plate of required size and letters duly bordred . Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ nut bolt/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge. (make Jindal or Equivalent)

Supply and fixing of Powder coated Aluminum Panel for directory of size 900mm x 750mm with partition of required Nos supported on aluminum channel 2 nos backiside with ACP sheet .Matter will Be digital print, matter covered with transprent polycarbonate sheet 0.5 mm wherever required completeand duly fixed with required nos of rawls plugs stainless steel srew/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage of reqired size complete with message. Matter will be digital print written single sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage two plates ( vertical type) of reqired size complete with message. Matter will be digital print written both sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of emergency sign boards single side of required size made of Photo luminescent film having glow power of 4 hours with message and graphics to be screen printing / vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge

Supply & Fixing Display notice pinup board of required size, aluminum beeding of 12 mm and fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supply & Fixing Key ring holder stand of size 900mm x 600mm. Front door covered with transparent acyrlic shhet and locking arrangment. Fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supplying and fixing of 18 gauge Stainless Steel Key Rings 1.245 mm thick (18 gauge) Stainless Steel plates of grade 304 etching (engraved)signage plate of Size 50mm x 38mm of and letters duly bordred as per sample approved and all as per sample. Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand written bth sides and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour as per direction of Unit Incharge

Supplying of Q Manager made of hollow stainless steel pipe of 18 gauge and 900 mm high including 1.30 mtr and 50mm width long ribbon etc. all complete as per direction of Unit Incharge.

Provinding and fixing transparent logos/ Letters made out of etching tape 3M sparkle type on the lean glass surface with plain water, scraping glass before fixing film with blade, spray soap solution on glass squeeze excess water and air bubbles. All as directed of approved shape and sizes etc fixed with of required size as required as per direction of Unit Incharge. Make 3M/ Avery Denson

Supply & Fixing signages for exit of size 375mm x 200mm x 8mm in acrylic sheet LED light with battary backup

Supply & fixing of signboard made out of 3mm thick sun board with face fully covered with digital print of approved shade and make. The sign board should be fixing on wall,fixed with four rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge.

Description

INTERNAL EIECTRICAL WORK

FIRE ALARM SYSTEM (ADDRESSABLE TYPE) AND PA SYSTEM

SUPPLY & INSTALLATION OF LIGHT FIXTURES & FANS

UPS SYSTEM

DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS

IP CCTV SYSTEM

AUTOMATIC FIRE DETECTION GAS SUPPRESSION SYSTEM

LIFT SYSTEM

SUB- STATION WORK

HVAC/VRV/VRF

Description of Item

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.l. box etc as required.

Group C

Wiring for group controlled (looped) light point/ fan point/ exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit etc as required.

Group C

Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate sutable GI box etc. as required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in sufface / recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2X2.5 sq. mm + 1X 2.5 sq. mm earth wire

4 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

2 X 16 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq, mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 1 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

Metre

Supplying and drawing co-axial W cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modula'r switch/ socket on the existing modular plate & switch box including connections but excluding modular plate.etc. as required.

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & swltch box but excluding modular plate as required.

Supplying and fixing following size/ modules, Gl box along with modular base and cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supplying and fixing Ding-Dong call bell suitable for single phase, 230 volts complete as required.

lnstallation, testing and commissioning of pre-wired, flourescent fitting / compact flourescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated. Copper conductor , single core cable and earthing etc. as required.

lnstallation, testing and commissioning of ceiling fan, including wiring the down rods of standard lengjth ( upto 30 cm ) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

lnstallation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos.3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ reeessed PVC conduit as required.

2 x 1.5 sq. mm

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCBilsolator)

8 way , Double door

12 way , Double door

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required, (But without MCB/RCCB/lsolator)

6 way ( 4 + 18 ), Double door, horizontal type

8 way ( 4 + 24 ), Double door, horizontal type

Supplying and fixing following ways, surface / recess mounting, vertical type, 415 Volts, TPN MCB distribution board of sheet steel dust protected duly powder painted inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required' (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door Vertical type

12 way (4 + 36), Double door Vertical type

Supptying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

6 A to 32 A, Single pole

Supplying and fixing following rating, 240/415 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6 A to 32 A, double pole

6 A to 32 A, four pole

40 A to 63 A, double pole

40 A to 63 A, four pole

Supplying and fixing single pole blanking plate in the existing MCB DB'complete etc. as required.

Supplying and fixing following rating, double pole, (singte phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required..

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides. and with inscription in single red colour on front side as required.

Supplying and fixing Cable end box (Loose wire box, lP43) suitable for following pole and neutral, sheet steel, MCB distribution board, 240 /415 V, on surface / recess complete with testing and commissioning etc. as required.

For 8/10 way, Double door SPN MCBDB

For 14 way, Double door SPN MCBDB

For 6 way, Double door TPN MCBDB

For 8 way, Doubte door TPN MCBDB

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.l. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.l. wire on surface or in recess for loop earthing etc. as required.

Froviding and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.l. strip on surface or in recess for connections etc. as required.

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.l. tube, having single prong at top, with 85 mm dia 6 mm thick G.l' base plate including holes etc. complete as required.

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.l. strip, 125 mm long, with 4 nos. of tlnned G.l. bolts, nuts, chuk nuts and spring washers etc. complete as required.

Providing and laying G.l. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part ll complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. ln the existing trench, complete as required.

120 mm dia (OD-120 mm & ID-103 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.

1 run of cable

2 run of cable

3 run of cable

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

6 sq. mm, 2 core

6 sq. mm, 4 core

10 sq. mm, 2 core

10 sq. mm, 4 core

16 sq. mm, 2 core

16 sq. mm, 4 core

35 sq. mm, 3.5 core

70 sq. mm, 3.5 core

150 sq. mm. 3.5 core

185 sq. mm, 3.5 core

240 sq. mm, 3.5 core

300 sq. mm, 3.5 core

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

185 sq. mm, 3 core

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

4X16 sq. mm

4X25 sq. mm

Supply & Laying of following sizes of 1.1KV grade Copper conductor XLPE insulated and FRLS PVC sheathed armoured control cable including termination conforming to relevant IS.

Meter

Meter

Meter

Laying of one number PVC insulated and PVC sheathed / XLPE powe r cable of 11 KV grade of following size direct in ground incl uding excavation, sand cushioning, Protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq' mm

Laying of one number PVC insulated and pVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with cable tie)

Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)

Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie)

Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 x 6 sq. mm (19mm)

2 X 10 sq. mm (19mm)

2 X 16 sq. mm (22mm)

3½ X 35 sq. mm (32mm)

3½ X 70 sq. mm (38mm)

3½ X 150 sq. mm (50mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm) including (4x6mm)

4 X 16 sq. mm (28mm)

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:

240 sq. mm (including 185 sq.mm)

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required

240 sq. mm (including 185 sq.mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

Supply, erection, testing and commissioning of following sizes of TV splitter of aluminium die cast body in suitable size of G.I. Box.

Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification.

100 mm wide x 40 mm deep.

150 mm wide x 40 mm deep.

Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification.

150 mm wide x 50 mm deep.

200 mm wide x 50 mm deep.

Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front door with glass as complete as required.

Supply & Fixing of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as r required.

Supplying & Placing of First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 etc as required.

Supplying & Installation of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) etc. as required.

1C x 50 sq.mm PVC Insulated cu wire including end termination.

Two Loop Panel.

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector acclimate type sensetive level (0.524%) OVS/ft. complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (75 DBA @3 mtr. & 75CD flashing)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supply, installation, testing and commissioning of addressable monitor module complete as per specification.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. Same make as of Fire Alarm System

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. Same make as of Fire Alarm System

Supply Installation, Testing & Commissioning of fire fighter main console at control room including power supply and accessories.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 480 Watt, supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

Speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing recess mounted following type LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 2' X 9 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing 4' X 20 watt LED batten with minimum efficacy 100 lm/w in aluminium housing and complete with integrated electronic driver etc directly on walll ceiling including connections with 1.5 sq.mm FRLS pVC insulated copper conductor etc. as required. (For Non-residential building)

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 7/12 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing Recess LED 1x1 ft luminaire made of pressure die cast alu. housing, LED Used shall be SMD type and fixture should have minimum efficacy >=100lumens/watt with Minimum system Lumens 2400 with maximum system wattage of 24W Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 6500K, CRI >80, PF >0.95, Minimum Internal Surge Protection 2.5KV & , The fixture should comply with the parameters as per IS10322. The LED driver should comply to IS 15885 sec 13 for Harmonics, IS 10322 for Electrical Safety. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. ( Approved Make- Oriant -LDRES or Equivalenlt)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.

250 mm sweep (1300/1400 RPM)

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 64 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

Single arm, 1000 mm

Supplying and fixing fotrlowing types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on poleibuilding including connection earthing the body etc as required.

Online UPS- Input supply: Three Phase, Output supply: Three Phase. Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of modules required for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter distance, rotections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. . Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and connectors and all required accessories are inclusive of the cost). This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display / LED) to display :

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U height with clear label holders and white label with the panel. 24 Ports Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Copper Patch Cords of length 1m (3ft)

Copper Patch Cords of length 3m (10ft)

Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required.

Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.

15 U Rack

Supplying and fixing 24U Rack with 4 inch Castor wheels and front brake Floor Standing Rack with Main Frame Pillar of 1.25mm Powder Coated CRCA Sheet with removable side panels, L- Shape adjustable Vertical Mounting Rail of 2mm with 'U'Marking completely knocked-down condition (CKD) Shape, fitted with 4 number cooling fans, minimum 5nos two line cable entry/exit provision at top and bottom with rubber protection, Front door 5mm Toughened Glass with MS frame or MS perforated with lock, Rear MS vented or perforated door, Powder coated Color- RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor Network Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting 802.3at PoE+ min.

Supplying, installation, testing and Commissioning of IP based voice communication system with 04 Port Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk lines (30 Channels) Circuit with CLIP Facility, min 200 IP users License with provision for further additions, 100 analog users, 01 Number IP based Operator Console, 100 Party Conference, Speed Dial, Music on Hold, Internal/ External ring difference, Call Barring, Call Pickup, Redundant server in active -Active mode and as per technical specification including supporting accessories etc complete as required. The system should have valid TEC GR approval from DoT.

Supplying, Installation, Testing & Commissioning of Type 1 IP Phone having 2 VoIP account, 120 x40 DOT matrix screen with backlight, Full HD duplex speaker phone, IPV6, Gigabit Etherent, PoE etc. complete as required.

Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for Network Switches. Must be hot Pluggable, RoHS Complaint, etc. complete as required.

10 G SFP + Single Mode/Multi Mode

Supplying and drawing following core Multi mode Fiber Optic Cable having corrugated steel armoring, leser optimize 50/125 μm with HDPE jacket, LSZH (Low smoke Zero Halogen), Tight-buffered or loose tube, maximum attenuation: < 3.5 dB/km at 850 nm, < 1.5 dB/km at 1300 nm, bandwidth > 2000 MHz-km at 850 nm, > 500 MHz-km at 1300 nm compliance and certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568- C.3, ITU-T G.651.1 RoHS compliant. Multi Mode Fiber shall be Central-loose tube filled with Thixotropic jelly, duly following Standards: ISO 11801, IEC 60793- 1/60794-1-2, ITU-T-REC G.652D and Telecordia GR- 20-core, High quality Electro Chromium Coated Corrugated Steel tape (ECCS ) and HDPE- Sheath, Operating ambient Temperature should be – 5 0C to +50 0C and Storage Temperature should be – 5 0C to +50 0C, Maximum Attenuation ± 3.5 dB/km at Operational Wavelength 850 nm and ± 1.5 dB / km at Operational Wavelength 1300 nm . type of fiber should be 50/125 / G.652D & Refractive Index should be 1.483/1.478, The value for Mode-filed,Cladding Diameter 50 ± 2.5 μm and 125 ± 1μm correspondingly i/c splicing & marking etc complete as required.

6 Core Multi Mode Optical Fiber Cable

Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted cable saddles for jumper management, suitable to manage both splices and terminations, Pre-assembled shelves in multiple configurations, Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers, 2 fiber spools built-in for 900μm tight buffered fiber storing, Capable of storing up to 3 meters of 900μm tight buffered fiber per adapter, Removable front and rear covers for better access to interior of LIU, Should be Single / Multi mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear screws, and spiral wrap tube etc complete as required.

24 Port LIU

Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC Fiber Duplex having high precision ceramic ferrule with good concentricity, Fiber corning single mode G652D, Cable Type 2mm with Mechanical specification Apex Offset < 50 μm, Fiber Height + 100 nm, End-face radius of Curvature 7mm < R <25mm, Repeatability < 0.2 db, Working ambient Temperature – 5 0C to +50 0C, Storage Temperature – 10 0C to +50 0C, Length -- 2meter, Type -- LC-LC Duplex etc complete as required.

Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for High density use having features and specifications etc. as mentioned here under- WiFi6 802.11ax 574Mbps (2.4GHz) + 2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console port, MG 2.5G LAN POE Port, factory reset, WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point, WDS, WDS with AP, Wireless Client ., Web (HTTP), Secure Socket Layer (SSL), Traffic control, Support ATF/Fast Roaming/Band Steering, Supports enhanced security – WPA-PSK/WPA2- PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC. Works as Standalone, Compatible with S/W & H/W Controller with addtional features like - Real-Time Monitoring and Alerts, Rich Advanced Features, Centralized Device Management, Role-Based Administration, Real-Time Monitoring, VLAN and Access Control, Auto RF Management and Bandwidth Optimization, Multi-SSID and Captive Portal Authentication.OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required

Supplying Installation Testing and Commissioning of 4MP IP IR Dome Camera having following specifications and features etc 1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in live & recorded video 2) Image Sensor: 1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 3) Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4) Wide Dynamic Range:- WDR (120dB or more) 5) Digital Noise Reduction:- DNR (3D) On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP (2560×1440)25/30fps, Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection 8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade 9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card. 10) Recording Management: Format SD, overwrite, storage management, video to NAS device 11) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection 12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast 13) System Capability: ONVIF, Camera shall support open source VMS

4MP @ 25/30fps@1440P (2560 x 1440) Dome Camera with 2.8/ 3.6/ 6/8/12 mm fixed lens (as per site requirement).

Supplying Installation Testing and Commissioning of 4MP IP IR Outdoor Bullet Camera having following specifications and features etc 1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in live & recorded video 2)Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 3) Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4) Wide Dynamic Range:- WDR (120dB or more) 5) Digital Noise Reduction:- DNR (3D) On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP (2560×1440)25/30fps Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection 8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade 9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card. 10) Recording Management: Format SD, overwrite, storage management, video to NAS device, 11) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection 12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

4MP @ 25/30fps@1440P (2560 x 1440) Outdoor Bullet Camera with 2.8/ 3.6/6/8/12 mm fixed lens (as per site requirement)

Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with camera licenses to record for all channels having specifications and features etc as mentioned below 1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to record per NVR and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more and must be ONVIF with minimum support of 384 Mbps incoming Bandwidth. 2) NVR should support video compressions : H.265 or better, H.264, MJPEG. 3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u, PCM, G726 audio compressions. 4) Intelligent auto power on when power resumes after power outage. 5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID support of RAID 0/1/5/6/10. 6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA Port 7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0) 8) Video Output Ports: 2x HDMI and 2 VGA 9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external sensors and output devices like hooter/ Siren etc. 10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for power failure, HDD failure, vandalism, tempring, network disconnection and panic 11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for alerts and viewing 12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM Cloud for remote monitoring without any public IP need 13) Standards: CE, FCC, RoHS, BIS Certified 14) PPower Supply : Should support AC100-240V, 50/60Hz Power supply. 15) Operating Condition : -5°C to 50°C, humidity 90% (max) (non-condensing)

64 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/36/64, 2nd screen: 1/4/8/9/16 Hard Disk Drive

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

8TB (Terabytes)

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor Network Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting 802.3at PoE+ min.

LED Display Supplying, Installation, Testing and Commissioning of 55 inch or larger LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required.

Supply, fixing, testing and commissioning of Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based FK 5-1-12 Pre-Engineered System for Electrical Panels (consisting of the following components.)

4.0 KG UL Listed Cylinder Automatic Pre-Engineered System filled with Clean Agent FK 5-1-12, Fitted with DLP Valve mounted on Cylinder Push-In-Connector for Tube, Mounting Bracket, End of Line Adopter and UL Listed Low Pressure Switch for Monitoring System Activation.

6.0 KG UL Listed Cylinder Automatic Pre-Engineered System filled with Clean Agent FK 5-1-12, Fitted with DLP Valve mounted on Cylinder Push-In-Connector for Tube, Mounting Bracket, End of Line Adopter and UL Listed Low Pressure Switch for Monitoring System Activation.

UL Listed Linear Pneumatic Heat Detection Tube with all necessary fittings & supports, HR Grade,UV Protected, MultiLayered, Made of Special Modified Polyamide Material, Inner diameter 4mm, Outer Diameter 6MM, Operating Pressure 15 8Bar, Maximum Pressure 30 Bar at maximum Temperature of +65 Degree C, Pressurized.

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System (Supply to be provide by the end client at 220 Volt AC).

Main L.T. Panel with AMF

AUTOMATIC POWER FACTOR CORRECTION PANEL (CAPACITOR PANEL)

UPS OUTGOING PANEL (GROUND FLOOR)

AMOUNT (DSR)-Rs.

Document Name-

Rev No-

Description

16 HP (1x16HP)

1.6 TR (550 CFM)

2.0 TR (650 CFM)

2.5 TR (800 CFM)

1.1 TR (330 CFM)

1.3 TR (375 CFM)

1.6 TR (500 CFM)

2.0 TR (650 CFM)

2.3 TR (700 CFM)

2.5 TR (800 CFM)

1.1 TR (375 CFM)

1.3 TR (475 CFM)

1.6 TR (575 CFM)

2.0 TR (700 CFM)

2.6 TR (875 CFM)

3.3 TR (1200 CFM)

4.0 TR (1400 CFM)

4.6 TR (1650 CFM)

6.5 TR (2400 CFM)

8.0 TR (2850 CFM)

4.5 TR (650CFM)

6.5 TR (1100CFM)

Indoor Units

Outdoor Units

Maximum 64 Nos of Indoor Units

1.0 TR (5 Star BEE Ratings)

1.5 TR (5 Star BEE Ratings)

7,000 CFM (20.0TR) , 60 mm St. Pr., 6 Row CC

AHU Kits & Controllers-(12-16HP)

Cassette Type (4-Way)

Ductable Unit & TFA

DX FMAHU

Capacity 6000 CFM, SP 25 mm wg

Capacity 6000 CFM, SP 25 mm wg

Capacity 8000 CFM, SP 25 mm wg

Upto 300 CFM at 10 mm static pressure

400 CFM at 10 mm static pressure

600 CFM at 12 mm static pressure

700 CFM at 12 mm static pressure

300 mm sweep dia (900 RPM)

380 mm sweep dia (900 RPM)

250 mm sweep dia (900 RPM)

300 mm sweep dia (900 RPM)

2C x 1.5 Sq mm (Shielded-Unarmoured)

6.4 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

9.5 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

12.7 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

15.9 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

19.1 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

22.2 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

25.4 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

28.6 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

31.8 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

34.9 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

38.1 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

41.3 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

25 mm dia

32 mm dia

40 mm dia

50 mm dia

0.63 MM (24 Gauge )

0.80 MM (22 Gauge )

1.00 MM (20 Gauge )

1.25 MM (18 Gauge) Plenum

0.63 MM (24 Gauge )

0.80 MM (22 Gauge )

1.00 MM (20 Gauge )

1.25 MM (18 Gauge) Plenum

9 mm (Return Duct)

13 mm (Supply Duct)

19 mm (TFA Duct)

50 mm thick

20 mm For Duct

25 mm For Plenum

Supply,. Installation, testing and commissioning of 18 Gauge G.I construction Frame with 22/24 Gauge GI Aero foil blades Volume control Duct/Wall Dampers with linkages, levers & fittings for Controlling the Airflow in Ducts with neoprene rubber gaskets,nuts, Bolts, Screws Linkages, Flanges etc. as per specification.

Motorized (ON-OFF Type) duct mounted GI volume control damper

Motorized (ON-OFF Type) duct mounted GI volume control Actuator

Grilles with Dampers

Grilles without Dampers

Supply & Exhaust air with dampers

Return air without damper

400mm dia. Eye Ball Type Jet Nozzles (Double Skin) With aluminium Butterfly Damper with Adjustable discharge angle upto +_30 degree.

3-Slot Diffuser

2-Slot Diffuser

Supply and fixing of non vision air transfer door grille of powder coated extruded aluminium, single deflection grille with horizontal vanes arrangement etc. as per specifications and drawings.

Fire Damper

Actuator

40A 4P MCCB(25 KA) 10.1 to 14.0HP

63A 4P MCCB(25 KA) 14.1 HP To 22.0 HP

4C x 16 Sq. mm Copper Conductor (Armoured) 14.1 HP To 22.0 HP

4C x 10 Sq. mm Copper Conductor (Armoured) 10.1 to 14.0HP

4C x 6 Sq. mm Copper Conductor (Armoured) Upto 10.0HP & AHU

4C x 4 Sq. mm Copper Conductor (Armoured) For AHU, Axial Flow Fan & Ductable Unit

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

Compressive AMC (After Two Years)

Non Compressive AMC (After Two Years)