renovation

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within CSIO. All kinds of soil.

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. Make TATA/SAIL or Equivalent

Centering and shuttering including strutting, propping etc. And removal of form for :Foundations, footings, bases of columns, etc. for mass concrete .

Centering and shuttering including strutting, propping etc. And removal of form for :Shelves (Cast in situ),Lintels, beams, plinth beams

Centering and shuttering including strutting, propping etc. And removal of form for : Columns, Pillars, Piers,cantilevers, Abutments, Posts and Struts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation12.5 in foundation and plinth in:Cement mortar 1:4(1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4(1 cement : 4 coarse sand)

Half brick masonry with F.P.S. brick of class designation 12.5 in foundations and plinth/ superstructure in. Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Make :- Dorma/Dorset/Indobrass

Providing and fixing aluminium sliding door bolts, ISI marked poweder coated to required colour or shade, with nuts and screws(also powder coated) etc. complete : 250x16 mm Make:- Classic or Equivalent

Providing and fixing aluminium tower bolts, ISI marked, powder coated to required colour or shade, with necessary screws(powder coated) etc. complete : 250x10 mm Make:- Classic or Equivalent

Providing and fixing aluminium tower bolts, ISI marked, powder coated to required colour or shade, with necessary screws etc. complete : 150x10 mm Make:- Classic or Equivalent

Providing and fixing aluminium handles, ISI marked, powder coated to required colour or shade, with necessary screws etc. complete : 125 mm Make:- Classic or Equivalent

Providing and fixing aluminium handles, ISI marked, powder coated to required colour or shade, with necessary screws etc. complete : 100 mm Make:- Classic or Equivalent

Providing and fixing aluminium hanging floor door stopper,powder coated to required colour and shade, with necessary screws etc. complete. Twin rubber stopper Make:- Classic or Equivalent

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Make TATA/JINDAL

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes Make TATA/JINDAL

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Providing and laying Double Charge vitrified floor tiles in different sizes (thickness to bebspecified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.Make :- Kajaria. (Tile to be Cleaned after fixing of any stains, patches etc before payment)

Providing and laying Double Charge Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm.Make :- Kajaria (Tile to be Cleaned after fixing of any stains, patches etc)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Make :- Kajaria

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Make TATA/JSW

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) Make TATA/JSW

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.Two or More coats on new work including of one coat Primer . Make :- Asian/Narolac/Dulux.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work Make :- Asian/Narolac/Dulux.

Removing dry or Oil distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make :- JK wall putty/Birla white/Asian

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. Make :- Asian/Narolac/Dulux.

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on base of Enamel paint/ steel galvanised iron/ steel works Make :- Asian/Narolac/Dulux.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Taking out existing wooden and aluminium door/Cupborad/Window shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two coats on old work Make :- Asian/Narolac/Dulux.

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface Make :- Asian/Narolac/Dulux.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CSIO as per direction of Engineer-in-charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within CSIO as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in- charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area beyond 3 sq. metres

Dismantling aluminium/ Gypsum/steel/wooden partitions, doors, windows, fixed glazing and false ceiling, plaster ,kota stone,sun film ,wall paper, pvc flooring,G.I sheets roofing including,M.S. structure, ceramic tiles,chips/ mossaic/brick/stone flooring etc including disposal of unserviceable surplus material and stacking of serviceable material with CSIO as directed by Engineer-in-charge

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond CSIO for all leads including all lifts involved

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap Make :- Cera/Hindware/Parryware

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia Make :- Viking or Equivalent

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Make :- Saint Gobind or equivalent

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps i/c making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 15 mm dia nominal bore. Make :- Jindal/TATA

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.50 mm dia nominal bore Make :- Jindal/TATA

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore Make :- Viking or Equivalent

Providing and fixing G.I. Union in G.I. pipe including cutting andthreading the pipe and making long screws etc. complete (New work) :15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore Make :- Cera/ESS ESS

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore Make :- Cera/ESS ESS

Providing and fixing CP grating of approved quality and colour. Circular type 100 mm nominal dia make :- Chilly/Vikings or Equivalent

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/Including filling of sapce between frame and wall with sealent appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / matching colour powder coated stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion . Powder coated aluminium (minimum thickness of powder coating 50 micron) ( The aluminium to be cleared properly of paint etc before payment ) (Clean of aluminium to be done)

Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS : 1285, fixed with rawl plugs and screwsor with fixing clips, or with expansion hold fasteners ncludingnecessary filling up of gaps at junctions, at top, bottom and sides withrequired PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / matching colour powder coated stainless steel screws, all complete as per architecturaldrawings and fiklling the gap between aluminium and wall with PU sealent the directions of Engineer-in-charge. (Glazing andpaneling to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision forfixing of fittings wherever required including the cost ofPVC / neoprene gasket required (Fittings shall be paid forseparately).Powder coated aluminium (minimum thickness of powder coating 50 micron). ( The aluminium to be cleared properly of paint etc before payment ) (Clean of aluminium to be done)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides Make :- GVK/Novapan/Merico

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) Make :- Saint Gobind/Modi Guard/Atul

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Make :- Godrej or Equivalent

Providing and fixing aluminium Double bend handle round with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium as per direction of Engineer-in-charge

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and as per direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing & fixing vertical blinds of louvers fabric woven of approved shades.The head rail should be powder coated aluminium alloy section with tilt gear hub delrinacetal louer carriers including any other fixtures to make the blind oprational and fixing in position all complete of Make - Vista or equivalent as approved by Engineer in charge before fixing.

Providing and fixing of sun control film reflective type of 3M / Garware Polyster Ltd. Or Equivalent on glasses of window/ doors of rooms all complete as directed by Engineer in charge.

Providing & Supply of mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern 16 mm Dune RH99 of Armstrong all complete as directed by Engineer in charge.

Providing & Fixing of true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.of Armstrong all complete as directed by Engineer in charge.

Removing existing false ceiling tile & grid and fixing the same for all heights including of angle & hanger wherever required with true horizontal level suspended ceiling using galvanized mild steel /6 mm diameter fully threaded hanger rod up to 1000 mm lengt on interlocking T-Grid complete as directed by Engineer in charge.

Removing,modification of vertical/Horizontal blinds accordingly to the size including of weight, rollers, pelmet, clips, pull string & any other accessories etc wherever required & refixing the same complete to fixed in postion as per direction of Engineer in charge.

Removing,Laying & Fixing the same PVC flooring with adhesive of approved brand all complete as directed by Engineer in charge. (The old/New PVC will be supplied free of cost by CSIO)

P/F of aluminium work for doors, windows and partitions in fixed portion including Screw & neoprene rubber wherever required. (The old aluminium will be supplied free of cost by CSIO) all complete as directed by Engineer in charge.

P/F of aluminium work for doors, windows for openable portion with all door fittings including Screw & neoprene rubber wherever required (The old aluminium will be supplied free of cost by CSIO)all complete as directed by Engineer in charge.

Taking out & fixing the same Steel sink/ china ware wash basin of any size with Old fittings accessorie, including painting the fittings and brackets, cutting and making good the walls wherever required:

P/F C.P. Laboratary Water Tap of approved quality conforming to IS:8931 15 mm nominal bore.

Carry out petty Job for welding works with neccesry Tools, welding set & rod etc. For petty works which otherwise can not be measured all complete as direction by Engineer in Charge

Making architecterual plan and drawings from a registered Architect and structure designing from a Structural Designer of the proposed building /sitting space and vetting the same frome reputed Govt Agency .(the Architect and Structural Desiner to be got approved by Engineer-in Charge )

Brick work with common burnt clay F.P.S. (non modular) old bricks(including Cleaning of Brick before laying in super structure or foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) ( old bricks will be suplied free of cost by CSIO )

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required : 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required : 450 mm width X 50 mm depth X 2.0 mm thickness

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply of power cable of 1.1 KV grade 3 ½ Core 120 sq. mm, Aluminium conductor, armoured, XLPE insulated and PVC sheathed, confirming to latest standard.

Supply of power cable of 1.1 KV grade 3 ½ Core 70 sq. mm, Aluminium conductor, armoured, XLPE insulated and PVC sheathed, confirming to latest IS standard.

Supply of power cable of 1.1 KV grade 4 Core 10 sq. mm, Aluminium conductor, armoured, XLPE insulated and PVC sheathed, confirming to latest IS standard.

Supply of power cable of 1.1 KV grade 4Core 35 sq. mm, Aluminium conductor, armoured, XLPE insulated and PVC sheathed, confirming to latest IS standard.

Supply of power cable of 1.1 KV grade 4 Core 16sq. mm, Aluminium conductor, armoured, XLPE insulated and PVC sheathed, confirming to latest ISstandard.

Supplying and fixing of 50mm sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of 200 mm X 300 mm X 100 mm deep sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Providing and fixing of 200 Amp, 16 KA, TPMCCB rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

Supply, installation, testing & commissioning of Switch Fuse Unit Box with aluminium bus bar chamber of TPN 250Amp. made of 1.6mm thick sheet steel enclosure duly painted with powder coating (Apx. size : 450mm x 950mm x 275mm) fully PVC insulated 4 Nos aluminium bus bars in convenient sections and suitable for 415 volts, 3 phase, 4 wire, 50 Hz, A.C. supply and earthing with 2 runs of galvanised iron strips etc. as required

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm (clamped with 1mm thick saddle) on wall surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) on wall surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) on wall surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm (clamped with 1mm thick saddle) on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) on cable tray as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 3½ X 35 sq. mm (32mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 3½ X 70 sq. mm (38mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 3½ X 120 sq. mm (45mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 10 sq. mm (25mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 16 sq. mm (28mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Disconnection,dismantling, shifting, reinstallation, testing & commissioning of electrical control panel with elecrical acessories including earthing the body etc. complete as required at site with minor civil work . : Control Panel size : 1700mm x 920mm x 360mm

Disconnection,dismantling, shifting, reinstallation, testing & commissioning of electrical control panel with elecrical acessories including earthing the body etc. complete as required at site with minor civil work . : Control Panel size :1450mm x 1270mm x 330mm

J P Constructions