CERTAIN B/R REPAIR OTM ACCN AND OTHER CONNECTED WORKS TO DEPOT AREA AND REPAIR/REPLACEMENT OF INTERNAL WIRING AT OFFICE AREA, OTM ACCN, GUARD POST AND OTHER TECHNICAL AREA INSIDE DEPOT AT BHARATPUR MILITARY STATION

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified and as directed.

Dismantling of cast iron, wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed.

Taking down shutters (including fittings & fixtures) of any description area exc 1 Sqm and not exc. 2 Sqm each, complete all as specified and as directed.

Taking down shutters (including fittings & fixtures) of any description area exc 2 Sqm each, complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified & as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 and including demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm prelam PVC sheet front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified & as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelam single side prelam PVC sheet & edge will be painted to match with prelam sheet reinforced with MS square tube etc, fixing in opening as per specifications complete all as specified and as directed.

S&F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) fixed complete all as specified and as directed.

S&F 100mm aluminium handle, cast type, anodised, complete all as specified & as directed.

Supply and fixing door closer hydraulically regulated, designation No. 3, universal type (ISI marked) aluminium (extruded section body) suitable for door shutters of 851 to 1000mm in width and weigth between 61 to 80 Kg and fixed, complete all as specified & as directed.

S&F mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc. conforming to Grade E-250 quality `A’ all as specified and as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ complete all as specified and as directed.

S&F mild steel work as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Grade E-165 (Fe 290), complete, all as specified & as directed.

S&F aluminium work powder coated of any colour as approved (thickness of powder coating not less than 50 micron) as in frame & shutters for doors, windows, ventilators, wall partitions, including joining cleats, glazing clips, snap beading, screws for fixing, etc., all aluminium sections as per relevant IS, complete all as specified & as directed. Note : Glass shall be measured and paid for separately as “Supply only” under respective item of this Schedule.

S&F aluminium window and ventilator shutters, powder coated of any colour as approved (Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.), including providing opening for AC in Window where directed, complete all as specified & as directed. Note : Glass shall be measured and paid for separately as “Supply only” under respective item of this Schedule.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed. Note : Glass shall be measured and paid for separately as “Supply only” under respective item of this Schedule.

S&F aluminium deco grill in door and windows with weight not exceeding 1.0 Kg/sqm including necessary arragement for fixing etc complete all as specified & as directed.

S&F for 0.56mm thick aluminium alloy sheeting fixed with screw on door shutter complete all as specified & as directed.

Supply and fixing PVC wall panelling in replacement of with panel 300mmx6mm Hollow section of sintex pattern SPUF-146 or equivalent, fixed with PVC plug and screws and inserted to next panel groove, edges and corners of all door/window/ openings etc to be covered with PVC angle fixed with solvent cement complete all as specified as manufacturer's instruction complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling roof (corrugated, semi corrugated, plain etc.) sheets as in roof coverings etc including ridges complete all as specified and as directed. Note : Colour of sheet shall be as approved by the GE.

S&F Pre-painted galvalume aluminum zinc coating Plain steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/ridge/fascia/cladding to wall, fixed with self tapping screws including dismantling roof (corrugated, semi corrugated, plain etc.) sheets as in roof coverings etc including ridges complete all as specified and as directed. Note : Colour of sheet shall be as approved by the GE.

M&L for false ceiling with 4mm thick high pressure steam cured non asbestos designer fibre cement board fixed aluminium frame work with screwss in ceiling flat or sloping complete all as per manufacturer’s instructions, all as specified and as directed. Note : Design & shade of cement board shall be as approved by the GE.

Supply and fixing anodized aluminium snap grid frame work for false ceiling, size of grid 605mm x 605mm including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified & as directed.

M&L for joint free non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed.

M&L for Vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade & pattern as approved by GE), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed.

M&L for factory made chequered cement concrete tiles, 20cm x 20cm x 22mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, over & including 15mm thick screed bed in cement & sand mortar 1:6 over & including 75mm thick PCC (1:4:8) type D2 using 40mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified & as directed.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape of paver blocks shall be as approved by the GE.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & as directed.

M&L for rendering 15mm thick in cement and sand mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth with using extra cement, including taking down cement plaster or cement lime plaster of any description complete all as specified and as directed.

M&L for rendering 15mm thick in cement and sand mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, including taking down cement plaster or cement lime plaster of any description complete all as specified and as directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for rendering 15mm thick in cement and sand mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) white or tinted (copolymer based resin glue to be added for longer durability and better finish) using hand roller over one coat of water based white pigmented alkali resistant priming paint conforming to IS-109-1968, over & wall suface including all necessary arrangement for execution of work complete all as specified & as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint using hand roller over one coat of water based white pigmented alkali resistant priming paint conforming to IS-109-1968, of approved colour/camouflaging pattern complete all as specified & as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including provision of glazing pins/spring clips icnlduing hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

Supply only 4.8mm thick sheet glass with solar control film 25 micron reflactive type sticked to glass pane, ordinary quality and glazing with neosprene beading exc 0.50 sqm in each pane complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, taking up or down old unserviceable steel water tubing and connections of 15mm bore complete all as specified and as directed.

Supply only 100mm aluminium alloy hinges complete all as specified and directed.

Supply only 125mm aluminium alloy handle complete all as specified and directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. Note : (i) The water storage tanks shall be 2 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. Note : (i) The water storage tanks shall be 2 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item.

S&F in replacement of Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

M&L for point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etc all as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete all as specified and as directed including taking down carefully existing unserviceable/perished surface conduit/concealed conduit/batten/casing caping aluminium/copper point wiring any type for light, fan, bell/buzzer, socket, power point including switch, socket, ceiling rose, fan regulator, bell push, bell, lamp holder etc complete. Note : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

All as per serial item No. 52.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed.

All as per serial item No. 52.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed.

All as per serial item No. 52.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F bell push, flush type, 5 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F switch piano, flush type, single pole, one way, 15/16 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F socket outlet, 3 pin (2 in 1, with 2 pin outlet also), 5/6 Amp, flush type, 230 Volts, ISI marked, complete all as specified and as directed.

S&F socket outlet, 2 in 1, 3 pin, 5 and 15/16 Amp, flush type, 230 Volts, ISI marked, complete all as specified and as directed.

S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed.

S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit fittings, ISI marked, complete all as specified and as directed.

S&F electronic fan regulator, flush type, stepped type with 5 step control, 230 Volts, 150 Watt, including making hole in sheet top cover and connecting up, ISI marked, complete all as specified and as directed.

Supply and fixing Bell ‘Multi Music’ Type, AC, 230 Volts, ISI marked, complete all as specified and as directed.

S&F in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 Watt 220 Volt, 50 Hz AC, ISI Marked, decorative type with driver holder and LED lamp, correlated colour temperature shall be minimum 6500 degree Kelvin, including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in replacement of LED tube light fitting 20 Watt, 6000 K, 230 Volt, 50 Hz, retro fit type 4 feet long, with replacable rod complete with all accessories including connection with three core twiste flexible copper conductor cable complete all as specified and as directed.

S&F in replacement of sensor based 20 watt LED tube light fitting, batten type, 4 feet long with rod complete with all accessories and including connection with three core twiste flexible copper conductor cable 230 Volt, 50 Hz, complete all as specified and as directed.

S&F in replacement of LED light fitting 14 watt, 230 Volt decorative wall mounting type with multicolour ABS housing with poly carbonate rings and glass shade with lamp holders & bulb with connector block etc complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement of luminaire 600mm x 600mm, 35/36 watt, 220 Volt, AC recessed type with high efficiency PMMA diffuser soft glare free high complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in replacement round/square shape 12 watt, 220 volt AC recessed type with high efficiency PMMA diffuser soft glare free light complete drivers, holders, LED lamp suitable for roof including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and Fixing in replacement of Light Emitting Diode (LED) based street/ security light fitting, 35 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 3000 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA /polycarbonate /toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multi stranded copper conductor cable of 1100 Volt grade (ISI marked), fixed complete all as specified and as directed.

NOTES FOR LED LIGHT FITTINGS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

Supply and fixing mounting bracket (suitable for fixing/holding street/security light fittings) made of 40mm bore GI pipe ‘light grade’ not less than 0.60m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, matching with section of Pole/suitable for wall, complete all as specified and as directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 230 Volt, 10 kA, ‘C’ Curve, fixed including taking down old unserviceable DB with fixtures of any type complete all as specified and as directed.

S&F sheet metal enclosure for distribution boards flushed and surface mounting factory made VTPN DB 4 way, 415 Volt, Double door type, IP-43 protection, IK-09 with metal door with 200 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) MCCBs/MCBs shall be measured & paid for separately under respective items of BOQ.

S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 8 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : (i) Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) MCBs shall be measured & paid for separately under respective items of BOQ.

S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 4 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : (i) Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) MCBs shall be measured & paid for separately under respective items of BOQ.

S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door (IP-43 IK 09 with metal door), suitable for fixing MCBs, 415 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar DB fully insulated bus bar neutral links blank plates, TPN, 4 way, suitable for frame MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) MCCBs/MCBs shall be measured & paid for separately under respective items of BOQ.

S&F in replacement of MCB, 6 to 32 Amps, Single Pole (SP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 40 to 63 Amps, Single Pole Neutral (SPN), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 32 Amps, Triple Pole Neutral (TPN), 415 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 63 Amps, Triple Pole Neutral (TPN), 415 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F MCCB 4 Pole 100 Amps, thermal magnetic having, breaking capacity 16 KA, 415 Volt in the existing location including taking out old unserviceable MCCB complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc including dismantling & taking out old existing unserviceable earthing complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

M&L for sub main wiring with two runs of 4 sqmm (nominal area) size main cable & one run of 4 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked cables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed. Notes :- (i) 02 runs of 4 sqmm size main cable, 01 run of 4 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked cables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed. Notes :- (i) 02 runs of 6 sqmm size main cable, 01 run of 6 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

M&L for sub main wiring with two runs of 10 sqmm (nominal area) size main cable & one run of 10 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked cables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed. Notes :- (i) 02 runs of 10 sqmm size main cable, 01 run of 10 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

Supply and fixing in replacement of 1100 Volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of aluminium stranded conductors of size 4 Sqmm complete all as specified & directed.

Supply, laying, jointing and testing LT XLPE insulated screened, bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Supply, laying, jointing and testing LT XLPE insulated screened, bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L for sand cushioning using clean local unwashed dry river sand for underground cable 8cm before laying cable and 15cm after laying and punned to 18cm after laying of under ground electric cable complete all as specified and as directed. Note : (i) Approved local unwashed dry river sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only punned thickness shall be measured.

M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed.

M&L for Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, floor, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete including taking down old unserviceable pipe with clamps complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately.

PD GUPTA AND COMPANY (BID ID -3474882)

krishna Associate (BID ID -3469634)

K P BUILDERS (BID ID -3470686)