REPAIR TO COMPOUND WALL, FENCING, BARBED WIRE, GATE, GATE PILLARS, FOOTPATH, HARD STANDING AND MISC REPAIR WORK IN THE AREA OF AGE B/R-III UNDER GE (WEST) JABALPUR

Amount

Taking down cement plaster / terrazzo of any description thickness including raking out joints hacking for key scrubbing down with water complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all specified and as directed.

M&L for 15mm thick rendering in CM 1:4 on concrete/brick surfaces using with water proofing compound as per manufactures instruction finished even and smooth without using extra cement complete all as specified and as directed. ( Note:- WPC shall be measured and paid separately)

Supply only water proofing compound.

M&L for applying two Coats of oil emulsion distemper over a coat of primer over 1mm thick wall care putty including Preparation on Newly Plastered Surfaces of internal walls complete all as specified and as directed.

M&L for applying two Coats of cement base paint over a coat of alkali resistant primer including Preparation on Newly Plastered Surfaces of external walls complete all as specified and as directed.

M&L for preparing new plastered or un-plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for Prepration of old surfaces of walls includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of cement based paint complete all as specified and as directed. Note:- Curing shall be done before and after applying of paint.

M&L for Prepration of old surfaces of walls includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of white wash on walls complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilliate demolition complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed.

M&L for TMT bars 6 mm to 8 mm cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed.

M & L for RCC 1:2:4 (Nominal mix) Type B1 using 20mm graded stone aggregate as in coloumn,pillars,piers, posts and struts complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and as directed..

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for 80 mm thick machine pressed precast concrete interlocking paver block of shape and size confirming to IS 15658-2006 of M-40 Grade with grey cement and pigment complete all as specified and as directed.

M&L for 60 mm thickness machine pressed precast concrete interlocking paver block and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment complete all as specified and as directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for Chequered cement concrete tiles 20 cm x20 cm x25 mm thick, set, jointed and pointed with grey cement and pigment to match over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers ,apex stones, bed plates, water troughs and the like including use of formwork (straight or curved) ,including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. (Note :-reinforcement where provided shall be measured and paid separately)

Demolition of brickwork or precast concrete articles, built in cement mortar including all quoins, arches, pillars,etc,but excluding ashlar facings and dressed stone work complete all as specified and as directed.

M&L for providing 35mm thick precast cement concrete louvers and jallies, type B0 1:2:4 (using 12.5mm graded stone aggregate) measured solid,including all mouldings but excluding frame and set in CM 1:4 complete all as specified and as directed.

M&L for Brick work with sub class ‘B’ brick, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. .

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, of any thickness, including cover fillets including E- Grid frame work complete all as specified and as directed.

S&F for suspended prepainted false ceiling, self design, self texture, using E grid exposed suspended system, grid section size 600mm x 600mm comprising of GI powder coated main runner of dimensions 39mm x 24mmx 08mm thick (thickness comprising of GI /0.4+PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length) cross tee of dimensions 29mm x 24mm 0.8mm thick and thick wall angle 22.2 mm x 22.2mmx 0.65mm thick (thickness comprising of GI /0.35+PPPCGS/0.3mm & weight of angle 0.70 Kg for 3050mm lenght) with and including 4mm thick HPSC (high pressure steam cured) pre-primed, self embossed, texture designer board, water resistant termitant, fire resistant for insulation and acoustic purpose to be placed in the grid systemduly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips (wt - 0.007 Kg/clip) hold down clips (wt-0.0035 Kg/clip) with provn of light fixture complete all as specified and as directed.

S&F for framed work as in doors or gates of angle or other section with gusset plates ,rails,braces etc complete drilled for fixing of steel gate sheeting or other covering,doors ,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering ,runing rails and guides ) and hanging also fastning and fixing confirming to FE-290 ( Gde E-165) complete all as specified and as directed.

Welding in repairs n. exc 2.5cm in length for fixing of door hinge, door spring , welding as in iron doors complete all as specified and as directed. (Note: one welder with one helper shall be deployed within 24 hours as per requirement base. Other wise a penalty of Rs 500 per Day shall be deducted on this account).

M & L for RCC precast NP 2 pipes of 300 mm dia laid and tested in trenches including dismantling of old pipe of any description complete all as specified and as directed.

M & L for RCC precast NP 2 pipes 450 mm dia laid and tested in trenches including dismantling of old pipe of any description complete all as specified and as directed.

M & L for PCC (1:3:6) type C2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under and haunching against the side of pipe after they are laid and tested complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness as in floors, aprons etc laid dry and pointed complete all as specified and as directed.

M&L for Granite (of any type ) 20 mm thick work (table rubbed and polished ) in steps ,jambs,pilllars,window cill,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2)using marble dust with admixture of pigment to match with shade of Granite laid over 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling post or struts (wood,steel or RCC ) of any description ,including taking out embeded portion in concrete or masonry and making good disturbed ground complete all as specified and as directed.

Dismantling fencing wire mesh,of any size and type complete all as specified and as directed.

Excavation in post holes n.exc 0.5 Cum each as in soft/loose soil, getting out and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 ( using 40 mm graded stone aggregate). as in foundation filling and mass concrete complete all as specified and as directed .

Supply only mild steel Galvanised wire Chain link fencing square mesh of any size complete all as specified and as directed

Fixing only chain link fencing in-cluding line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

S&F for hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and as directed.

S&F for mild steel screw bolt (machine made) with square or hexagonal head at one end, screwed other, fitted with washer and one hexagonal or square n exc 5cm, long and 5 to 10mm dia complete all as specified and as directed.

S&F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-0 or fe 250-0 complete all as specified and as directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of any description n exc 10 cm width or girth on newly painted steel surfaces complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of any description exc 10 cm width or girth on newly painted steel surfaces complete all as specified and as directed.

S&F for Punched tape concertina coil made out of low carbon strip duly electro galvanised , dia of wire not less than 2.59mm, dia of coil 600mm (appx) when closed with all necessary clips and RBT wire to connect with angle iron or brackets etc with all accessories complete all as specified and as directed. (Note: 6.00 RM coil weighing not less than 15 kg and streched to not more than 10.00 RM having not more than 51 circles /turns )

S&F for Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed. (Note: Each line wire shall be measured)

chandan construction (BID ID -3418568)

HAFEEZ CONSTRUCTION (BID ID -3418917)

a k builders (BID ID -3419509)

M/S A K MUKHERJEE (BID ID -3419328)

Mahakal Construction Company (BID ID -3413730)

M/s Om Infracon (BID ID -3418431)

Chetna Enterprises (BID ID -3470212)

Shri kamal traders (BID ID -3418272)

G.S.CONSTRUCTIONS (BID ID -3445324)

RAVI ENTERPRISES (BID ID -3445532)

DEEPAK CONSTRUCTION (BID ID -3420533)

deepak kumar vishwakarma (BID ID -3444503)

M/S BHARTI ENTERPRISES (BID ID -3418785)

chandra builders (BID ID -3445404)

kamakshi construction (BID ID -3470147)

M/S Modern builders (BID ID -3445027)

Hemant Associate (BID ID -3445303)