Under District Lucknow, Construction of Sardar Vallabhbhai Patel Memorial Gate at Lucknow Sultanpur Road, Gosai Ganj, Lot No 9

Work

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. DSR 2.31

Earth work in surface excavation not exXceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: 102/225 as per DSR 2.1.1

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm (nominal size) .DAR 4.1.8

Reinforcement cement concrete work in walls (any thinckess),including attached palster , columns ect. above plinth level . 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggreate 20mm.Rate as per DSR 5.2.2

Steel reinforcement for RC.C. work including straightening. cutting, berding. placing in posiion and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars. As per DSR 5.22.1

P/F angle iron frame for doors, windows and ventilators of mild steel angle section of size 35x35x5 mm joints mitred and weled by angle iron 35x35x5 or 35x5 flat pieces to the existing T - iron frame or to the wall with dash fastener , including fixonf of ncessary butt hinges and screw and applying apriming coat of approved steel primer , all complete as per the direction of Enginneer-in-charge . Rate as per DSR 10.31

12 mm cement plaster finished with a floating coat of neat cement of mix : (1 cement: 3 fine sand) As per DSR 13.7.1

Painting or varnishing on iron work in small or new wood work with one coat of redy mixed priming paint and two coat of approved superior quality ready mixed paint of clear synthetic varnish including for proper completion of Wlrk. Paint to be used should confirm to th ISI . No 103, 1950 SI No. 641+642

Retro-Reflective Sheeting type XI with 4 mm thick ACM double side Manufacturing, supplying and fixing retro reflective sign boards made up of 4 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25 x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of chromate yellow primer (vertical MS-Tee support to be painted in black and white colours) . Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge. size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of requiredshade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge.