Repair and maintenance of Sub Divisional Veterinary Hospital at Hamirpur

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm (thirty centimetre) in depth, 1.5 m ( one point five metre) in width as well as 10 sqm (ten square metre) on plan) including getting out and disposal of excavated earth upto all leads and lifts for all kinds of soil including chiseling of hard rocks where blasting is prohibited including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m (One point five metre) in width or 10 sqm (Ten square metre) on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m (One point five metre), including getting out the excavated soil and disposal of surplus excavated soil as directed in ordinary rock and all kinds of soil including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position mechanical mixed and vibrated cement concrete of 1:4:8 (one cement : four coarse sand : eight graded stone aggregate) 40mm (forty millimetre) nominal size graded stone aggregate for all works of foundation and plinth,catch pit,toe walls and below pipe including the cost of centering and shuttering including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Dry stone pitching 22.5 cm (Twenty two centimetre) thick including supply of stones and preparing surface complete as per direction of Engineer-in-Charge includidng entire carriage carriage of materials within all leads and lifts and other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position cement concrete of 1:2:4 (One cement : Two coarse sand) : four graded stone aggregate 20 mm (Twenty millimetre) nominal size) size) for all work up to plinth level including the cost of centering and shuttering including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position specified grade of Reinforced cement concrete work 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etcetera above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Steel reinforcement (TATA /SAIL / JINDAL PANTHER/ Shyam steel make) for reinforced cement concrete work including straightening, cutting, bending, placing in position and binding all complete work including cost of binding wire upto all floor level mild steel and medium tensile steel bars of grade Fe-500D or more including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 (Twelve point five) conforming to IS: 2222 in superstructure above plinth level all floor level in cement mortar 1:6 (One cement : six coarse sand) : With F.P.S.(non modular) bricks including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm ( twenty into ten into two millimetre) and braced with flat iron diagonals 20x5 mm ( twenty into five millimetre) size, with top and bottom rail of T-iron 40x40x6 mm, ( forty into forty into six millimetre) with 40 mm ( forty millimetre) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing Kiln seasoned and chemically treated hollock wood wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). as per direction of Engineer-In-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royalty, malakana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing cup board shutters with 25 mm (Twenty five millimetre) thick veneered particle board (HD HMR) IS : 3097 marked of Action TESA / Green Ply/ Kit Ply/ Century Ply make exterior grade (Grade I), of approved make, including 2nd (Second) class teak wood lipping of 25 mm (Twenty five millimetre) wide x 12 mm (Twelve millimetre) thick with necessary screws and bright finished stainless steel piano hinges, complete With decorative veneering on one side and commercial veneering on other side complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing 250x16 mm (Two hundred fifty into sixteen millimetre) nominal size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetra. complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing 125 mm (One hundred twenty five millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetra complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying Vitrified glazed Floor Tiles of size 300x300x 9.8 mm (thirty into thirty millimetre into nine point eight) or more millimeter) of 1st quality conforming to IS : 15622, of Orient bell/ Kazaria/ AGL/ Rak/ Johnson & Johnson approved make, in all colours and shades of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick Cement Mortar 1:4 (one Cement : four Coarse sand), jointing with grey cement slurry @ 3.3 (three point three)kg/ sqm including grouting the joints with white cement and matching pigments etc., complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing 1st quality HD series Digital Glazed rectified ceramic tiles (300mmx600 mm size) ( Three hundred into six hundred millimetre) conforming to IS : 15622 (thickness to be specified by the manufacturer ) of Orient bell/ Kazaria/ Rak/Johnson & Johnson make , in all colours, shades except burgundy, bottle green, black as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm ( twelve millimetre ) thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm ( three point three kilogram per square metre) including pointings in white cement mixed with pigment of matching shade complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Steel work in built up tubular (TATA/SAIL/APPOLLO MAKE) (round, square or rectangular hollow tubes etc.) trusses, railings/ hand rail and other similar frame work etcetera including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etcetera Hot finished welded type tubes complete including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing Precoated Galvanised Iron Profile Sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) of TATA/SAIL/JSW Make 0.50 mm ( zero point five zero millimetre) + 0.05 % ( Plus zero point zero five percentage) total coated thickness with zinc coating 120 ( one hundred twenty) grams per square metre as per IS: 277, in 240 ( two hundred forty) mpa steel grade, 5-7 ( five to seven) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns. Sheet should have protective guard film of 25 ( twenty five) microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 ( twelve) metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size 5.5x 55 mm ( five point five into fifty five millimetre) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required upto all floor level/height including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Kota stone 25mm ( twenty five millimetre) thick slab flooring over 20 mm ( twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab , including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) upto all floor level including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Ridges Plain 500 - 600mm ( five hundred to six hundred millimetre) Precoated Galvanised steel sheet roofing accessories of TATA/SAIL/JSW Make 0.50 mm ( zero point five zero millimetre) + 0.05 % ( Plus zero point zero five percentage) total coated thickness, Zinc coating 120 ( one hundred twenty) grams per square metre as per IS: 277, in 240 ( two hundred forty) mpa steel grade, 5-7 ( five to seven) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen ) microns using self drilling/ self tapping screws complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

15 mm ( fifteen millimetre) cement plaster on rough side of single or half brick wall of mix 1:6 ( one cement : six coarse sand) upto all floor level including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and applying white Cement Based Putty of average thickness 1 mm ( one millimetre) of approved brand and manufacturer ( J K White/ Birla White ) over the plastered wall surface to prepare the surface even and smooth complete upto all floor level including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Distempering Two coats with 1st (First) quality acrylic distemper, (Asian/Nerolac/ICI Dulux) having VOC (Volatile Organic Compound ) content less than 50 grams/ litre (Fifty grams per litre), of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Sintex make Tripple Layers including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality of Jaquar (SQT-ESS-526) conforming to IS:8931 complete as per direction of Engineer-In-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royalty, malakana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) size Ball Valve (brass) of approved quality, High or low pressure, with plastic floats complete of Jindal /Tata /Zoloto/ UNIK make including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) nominal size G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etcetra concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall Jindal (Hisar) / TATA make including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) diametre single hole basin mixer of approved quality and make of Jal/Jaquar/Parryware/Hindware) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern ( Hindware or Jaquar), including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm ( five hundred fifty into four hundred millimetre) with a 15 mm ( fifteen millimetre) CP Brass single hole basin mixer of Hindware or Jacquar make (OPAL SERIES) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 32 mm (Thirty millimetre) dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings (Finolex/Supreme make) complete including entire carriage of material within all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and Fixing frosted glass panes 4 mm (Four millimetre) thick instead of ordinary float glass panes 4 mm (Four millimetre) thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) complete as per direction of Engineer-In-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royalty, malakana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing fly proof galvanized M.S. wire gauge With 2nd (Second) class teak wood beading 62X19mm (Sixty two into nineteen millimetre) to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm (One point four millimetre) in both directions with wire of dia 0.63 mm (Zero point six three millimetre) all complete as per direction of Engineer-In-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royalty, malakana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 600x450 mm ( six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm ( six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete of ( Modigaurd/ Atul/Cera/Exotica make) including entire carriage of materials within all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 75mm(Seventy five millimetre) dia high pressure PVC spigot and socket, waste and ventilating pipe I.S.I marked Finolex/ Supreme working pressure not less than 6 kg/sqcm (six kilogramme per square centemtre) complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 110mm(One hundred ten millimetre) dia high pressure PVC spigot and socket, waste and ventilating pipe I.S.I marked Finolex/ Supreme working pressure not less than 6 kg/sqcm (six kilogramme per square centemtre) complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

AASHISH KUMAR

MUKESH CHAND

MAHIPAL GOVT CONT

Yash Paul