SPECIAL REPAIR TO BLDG NO P-50 OF AC DEPOT AND PROVISION OF CERTAIN SANCTIONED WORKS IN THE AREA OF AGE B/R- II UNDER GE (N) AHMEDNAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil.

M&L for moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering complete all as specified and directed

M&L for hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. Complete all as specified and directed.

M&L for coloured glazed ceramic tiles digitally printed 300x450mm, 7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

Material and labour for joint free /rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free anti skid ceramic coloured tiles 300x300mm 7-8mm thick matching to dado tiles area of each tile, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge

M&L for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified

M&L for old size brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in 1: 6 complete all as specified

Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed

M&L for rendering, 20 mm thick (15mm+5mm) on brick/Stone Masonry/concrete surfaces in cement mortar 1:6 surfaces finished even and smooth without using extra cement including sagol finished complete all as specified.

M/L for 15 mm thick rendering on wall surface in CM 1:4 in with water proofing compound incl. finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid seperately)

M&L for rendering 10 mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and fair without using extra cement including sagol finished complete all as specified.

M & L for Rendering 10 mm thick in cement mortar 1:4 surface finished even and smooth without using extra cement on fair faces of brickwork or concrete surfaces.

M&L for rendering 10 mm thick in CM 1:3 by using 100% coarse sand on roof mixed with & including WPC @ 3% by weight of cement and finished the surfaces even and smooth without using extra cement.

M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M & L for preparation of newly plastered surface of wall and apply three coats of white wash any height including scaffholding etc complete all as directed.

M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffholding etc complete all as directed.

M & L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffholding etc complete all as directed.

M&L for preparation of old plastered or unplastered surfaces of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying one coat of white lime wash at any height including scaffholding etc complete all as specified and directed by Engineer-in-charge.

ditto all as per Sr item No 27 (here-in-before) but on ceiling.

M&L for complete removal of existing treatment of wall by steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots including washing down,with water etc.apply two coats of oil bound distemper over a coat of alkali resistant primer on old plastered surface of wall using roller including necessary scaffoldings etc complete all as specified .

M&L for 2 mm thick wall care putty etc complete all as specified and directed

S&F fix in repairs wash hand basin with pedestal vitreous China white , flat back or angle type of size 550 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge

S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous China urinal, Half stall type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe)

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmetc complete all as specified and directed by Engineer-in-Charge.

M&L full moulding/half moulding of stone slabs one edge, two edge, as in steps cooking platforms jambs and cills and other similar situations complete all as specified & directed.

Supply only 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections

Ditto all as per item No 39 above but 20 mm bore tubing

Ditto all as per item No 39 above but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Ditto all as per item No 42 above but 20 mm bore tubing

Ditto all as per item No 42 above but 25 mm bore tubing

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs stop cock/ anglecock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

Supply only 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply only PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per Sr Item No 52 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per Sr Item No 54 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F bands, straps, supports or stays for rain waterpipes, hooks (stay) heavy for large gates, hook and pintle hinges clamps, hold fasts wall ties, hooks for hanging fans and similar small articles Fe-290 Gde- E-165 or Fe-310-0 complete all as specifed and directed.

M&L for special treatment to sunken slab floor (Area of Sunken Portion n exc 1.50 Sqm) incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

M&L for special treatment to sunken slab floor (bottam and vertical portion) etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected including dismantling water tanks and removing to store etc complete all as directed.complete all as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected including dismantling water tanks and removing to store etc complete all as directed.

Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each etc complete all as specified and directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S & F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

S&F for factory made 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc all as specified

M&L for factory made 35 mm thick IInd C/L H/W plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing.

S&f Steel ventilator with top hung shutter including hinges, steel peg stay, complete

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S&F butt hinges medium weight cold rolled mils steel 100mm long.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long.

S&F aluminium anodised handle of extruded section 150mm long.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long.

S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S & F Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

Hacking out old broken glass ( any thickness size ,quality or description ) from wooden/Steel frames glazed with putty or fixed with beads.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide.

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint.

S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge.

S&F Chromium plated soap dish of Prayag polymers Pvt Ltd or equivalent

M/L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed.

M&L for PCC Type C-1 1:3:6 using 20 mm graded aggregates as in edges of floor tiles/blocks roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed by Engineer-in-Charge.

Dismantling of unframed work fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

M&L for machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge

M&L for 75mm thick plain cement concrete type C-1 (1:3:6) using 20 mm graded stone aggregate as in plinth protections & path, complete all as specified

M&L for 30mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only for 30mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed

S&F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring.

M&L for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness complete all as directed

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof fixed with self tapping screws complete all as specified, colour and design as approved by GE including dismantling of plain steel sheeting, any gauge, thickness.

S&F of Steel work in tubular trusses, Perlin, rafhter, including special shaped washer etc. complete conforming to I. S.1161-1979 grade St.-240

Material and labour for providing water proofing treatment on roofs, as per manufacturer's instructions and as specified after taking down/out as existing tar felt at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqm and allow to dry.(b) Applying and laying torch APP polymer modified bituminous membrane 3 mm thick with non woven polyester mat as reinforced weighing not less than 3 kg/sqm by thermo fusion process as per manufacturers specification (c) Applying one coat of aluminium paint on APP polymer modified bituminous membrane.

M&L for Reinforced concrete pipes 200 mm bore, class NP2, laid and jointed complete with collars

M&L for concrete bed to drain pipes in PCC 1:4:8 type-D2 using 40 mm graded aggregate including packing under, and haunching against the sides of pipes for 200 mm bore pipes after they are laid and tested; in

M&L for cement concrete type D2 1:4:8 using 40 mm graded aggregate in foundations, filling and mass concrete

M&L for PCC 1:3:6 Type - C1 using 20 mm graded aggegate as in coping including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for PCC 1:3:6 Type - C2 using 40 mm graded aggegate as in surface chanel, benching in manhole as directed

M&L for RCC pre cast manhole cover slab in 1:2:4 type -B1 using 20 mm aggrgate incl necessary form work and set in CM 1:6, cover slabs (for man holes etc.)

M&L for Mild steel bars up to 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Chage.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories with provn of PVC boxes and fixed with brass screws cup washer for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, bulkhead lights, bldg security light etc

One light point /fan point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

All as per Item No 119 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F switch piano flush type single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F switch piano flush type single pole, one way 16 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F Socket 3 pin 6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F Socket 2 in 1, 6/16 Amp etc complete all as specified and directed by Engineer-in-Charge

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L for ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs,, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way SPN, 240 volts ,protection class IP-42, suitable for fixing of MCBs, etc, Concealed in wall confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. Make: Legrand ,Cat No:5076 10 or equivalent in Simens/ Hager/ L&T

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply and fix square profile LED lighting fixture , environmental friendly, energy efficient ready to use pack Aluminium housing LED Tube light fitiing 22 Watt with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge

Supply and fix exhaust fan,steel body AC Single phase,230 V of size450m sweep with ,blades and frame and heavy duty all as specified

S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit 10 W LED ,IP65 ,IK 08 rated product luminaire comprising of high brightness LEDs complete with all accessories prewired and including connecting up with & including twin core twisted flexible copper conductor cable of suitable size etc complete all as specified and directed by Engineer-in-Charge

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :- (a) LT cable10 Sqmm, 2 core.

(b) LT cable10 Sqmm, 4 core.

(c) LT cable 50 Sqmm, 3.5 Core. Note for Sr Item No 135 to 137 : Excavation and earthwork, pipe protection shall be measured and paid seprately under relevant items of this Schedule.

Supply & laying of DWC(Double wall corrugated) HDPE pipe ISI marked with IS 16205 part 24 ( Pipe colour orange) of outer dia 63 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Supreme / Infra / Astral/Prince/jain irrigation

Supply & laying of DWC(Double wall corrugated) HDPE pipe ISI marked with IS 16205 part 24 ( Pipe colour orange) of outer dia 50 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Supreme / Infra / Astral/Prince/jain irrigation

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Supply and Laying in trenches or drawn through pipe or fixed on wall / poles , LT UG cable 1100 Volts, heavy duty XLPE insulated, screened, PVC bedded, galvanised steel strip or wired armoured with aluminium conductor after removing old one of following size:- (b) 10 Sqmm 4 Core

M&L for 12 Mtr high mast light pole (non motorised) octagonal type (90mm x 240 mm) PCD 320 mm , basic wind speed IS 875 Part III 2015, tarrain category 2 with made up hot deep octagonal GI sheet 3 mm thick including foundation 1700 mm deep and 200 mm above ground level, grade of M20 grade of steel reinforcement FE 415 FE 500m clear cover to reinforcement 50 mm , concrete vibrated with shuttering, foudation bolts size (M24 x 750 mm) 4/6 non suitable for mounting of high mast pole including bracket for 6 flood light, control panel ,ade out of 1.60 mm thick MS Sheet with three phase contractor 63 Amps, Contractor coil, Astronomical timer Switch and connected accessories complete and all as specified & directed. Make : Bajaj

Supply and fix in replacement of LED high mast light 200 watt with inbuilt surge protection 10KV, Lumuns output 20000 with energy saving, environmental friendly, long life, exclusive innovative die cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting protection and impact resistance IK07 fixed with clamp, Nut Bolt and Washer, connection complete alll as specified and directed. Make : Phillips/ Wipro/ Havells

M/L for GI Tubes,of size 50mm dia Medium grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

M&L for road cutting upto 300mm deep and 200mm wide for crossing GI pipe line through road including making good the disturbed surface by filling mass concrete( 1:2:4) etc complete all as specified and directed by Engineer-in-Charge. Note : Rate of mass concrete is included in quated rate.

Supply & Fixing and testing of LT cable 1100 volts grade, XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (heavy duty) ISI Marked with aluminium conductor suitable for earthed system of size 50 sq mm 3.5 core in trenches, on poles and in ducts complete all as specified and directed by Engr in charge.

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body with Aluminium bus bar 300 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc. Panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs, glands , Nuts & Bolts complete all as required and directed. (i) Incoming MCCB 4P 125 Amp, 25 KA -01 No( Ics = 100% Icu) (ii) Phase indicating LED lamps (R-Y-B) -01 set

M&L for earthing with galvanised steel earth plate electrode of size 600 x 600 x 6mm thick buried vertically in ground not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level and connected to GI strip 32x6 mm by means of nuts, bolts and washers and encased in and including 15 dia GI medium grade pipe upt 2.4 mtr height form ground level fixed by MS flat iron clamp 40mm x 5mm with nut, bolt and washers, GI strip fixed to base along pole and connected to over head line for providing earthing to HT pole/feeder AB switch LA complete with charcoal dust, salt packed around plate 150 mm thick including watering GI pipe, medium grade 40 mm dia with blanking cap 1.5 mtr long fixed to funnel with wiremesh complete with PCC chamber and RCC chamber over all as per Electrical Plate No 5 of SSR Part I - 2009 incl excavation and earth work in any type of starta and testing on compeltion. (Note: Any length of GI strip and 15 mm dia GI medium grade pipe shall be provided as per actual requirement at site)

Supply and Laying Flexible copper armed cable 10 Sqmm 4 core ,ISI marked laid on wall and in ducts complete all as specified and directed by Engr in charge.

M/S. Z.K.ENTERPRISES, AHMEDNAGAR (BID ID -3127799)

PRADIPKUMAR POPATRAO THUBE (BID ID -3127804)

Arihant Construction (BID ID -3127142)

MATOSHREE CONSTRUCTION (BID ID -3120729)

M/S MAHESHWARI ENTERPRISES (BID ID -3126956)

OM SAI ASSOCIATES (BID ID -3128776)

AZAD SERVICES (BID ID -3125497)