Special repair to Sarvodya Leper Colony Downdale Phagli Shimla(SH Repair of roof walls, plinth protection, sanitary fittings and painting, distempering etc. in block-1, 2 and 3)

Amount

Demolishing cement concrete nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) manually / by mechanical means including disposal of material within all leads and lifts as per direction of Engineer-in-charge including carriage of materials in all leads and lifts .

Dismantling tile work 10 mm to 25 mm in skirting / dado / floors and roofs laid in cement mortar including disposal of surplus material and stacking of useful material within all leads including carriage of materials within all leads and lifts as per direction of Engineer in charge. .

Dismantling G.S. Sheet / prepainted sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within all leads and lifts including carriage of materials within all leads and lifts as per direction of Engineer in charge.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within all lead including carriage of materials within all leads and lifts as per direction of Engineer in charge. .

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. of area 3 sq. metres and below complete and stacking within all lead including carriage of materials within all leads and lifts as per direction of Engineer in charge. ..

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within all leads. All kinds of soil including carriage of materials within all leads and lifts as per direction of Engineer in charge. .

Providing and laying in position cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including curing excluding the cost of centering and shuttering - All work up to plinth level :- including carriage of materials within all leads and lifts as per direction of Engineer in charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of materials within all leads and lifts as per direction of Engineer in charge.

Providing and fixing 2nd class deodar wood 35mm thick panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 19mm thick Commercial Board shutters for cup boards i/c fixing with nickel plated piano hinges with screws etc complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 19mm thick commercial board in shelves / box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails etc. complete. including carriage of materials in all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing hard wood square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete Triple strip vertical type including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and fixing 125mm size bright finished brass handles with screws etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge (Base members of steel work shall be measured and paid separtely) including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Dubbing out an old irregular walls average 10mm thick with Cement mortar 1:6 (1 Cement : 6 Sand) complete in all respect including carriage of materials and as per the direction of the Engineer-in-Charge as per direction of Engineer-in-charge. .

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 300x16 mm including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 250x10 mm including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 125 mm including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm including carriage of materials with in all leads & lifts as per direction of Engineer-in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Providing and laying vitrified floor tiles 600x600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. .

Painting wood work with Deluxe Multi Surface Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm of approved brand and manufacture including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Stone soling properly hand-packed filling interstices with Kharanja stone including spreading watering and of binding materials moorum or earth etc. complete as per HP.PWD specification including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying in position cement concrete 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) i/c curing, excluding the cost of centering and shuttering - All work up to plinth level including carriage of materials in all leads and lifts as per direction of Engineer-in-charge.

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. welded mesh 25mmX25mmX2mm thick as per approved design complete by welding with electrical plant complete including applying priming coat of red lead paint as per HP.PWD. Specification 1990 Volume-I and including carriage of materials upto all leads as directed by the Engineer in Charge.

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete150 mm including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 300x16mm ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade two or more coat applied @ 0.90 ltr/ 10 sqm of approved brand and manufacture including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :-New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Finishing walls with Acrylic Smooth exterior paint of required shade New work two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials and as per the direction of the Engineer-in-Charge as per direction of Engineer-in-charge.

Providing & fixing glass panes with putty and glazing clips in wood / steel doors, windows, clerestory windows, all complete with including 5.5 mm thick glass panes including carriage of materials within all leads and lifts as per the direction of the Engineer-in-Charge.

Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for all leads and lifts, including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc External work 15 mm dia nominal bore including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests including carriage of materials within all leads and liftsas per direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock & 32 mm dia PTMT waste .including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including carriage of materials within all leads and liftsas per direction of Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PTMT soap Dish with Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing C.P. brass Angle cock with CP flange of approved quality conforming to IS:8931 :-15 mm nominal bore including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing C.P. brass long body bib cock with CP flange of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing C.P. brass short body bib cock with CP flange of approved quality conforming to IS :8931: 15 mm nominal bore including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore including carriage of materials in all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 15mm nominal bore brass full way valve with wheel including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 15mm nominal bore brass ball valve (horizontal plunger type) High pressure with polythene plastic floatswith fixing etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 15 mm nominal bore G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and placing on terrace (at all floor levels) polyethylene three layer sintex make water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PVC Finolex type "A" floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. (i)-110mm X 90mm.

110mm X 75mm.

Providing and fixing high pressure PVC Finolex type "A" spigot and socket, waste and ventilating pipes including collar and clamps ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. :- (i) 110 mm dia.

75 mm dia.

Providing and fixing PVC Finolex type "A" single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. :- (i) 110mm nominal size.

75mm nominal size.

Providing and fixing PVC Finolex type "A" collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. (i) 110mm nominal size.

75mm nominal size.

Providing and fixing PVC Finolex type "A" plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. (i) 110mm nominal size.

75mm nominal size.

Providing and fixing 10.00 liter capacity PVC low level flushing cistern Hind ware sleek ultra of size 42 X 39 X 14cm or equivalent with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and ovrflow pipe, 40mm dia C. P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PTMT grating of approved quality and colour Circular type 100 mm nominal dia including carriage of materials within all leads and lifts as per direction of Engineer-in-charge.

Suresh Kumar