Special repair of Sub Health Centre at Village Deeghot in Palwal Distt. Re-Tender

Amount

Civil & P.H. Works

Dismantling of Cement concrete (HSR 8.6 e) reinforced cement concrete with cleaning and straightening and cutting of bars if required.

Removing door & window (wood and steel) with chowkats by making recesses in walls. (HSR 8.18). Door

Window

Ventilator

Scraping cement plaster (HSR 8.32 c)

Cement concrete 1:4:8 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.38)

Cement concrete 1:8:16 with stone aggregate 40 mm Nominal site in foundation and plinth. (HSR 10.28)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size in First Storey upto 4 metres abvoe plinth level (HSR 10.59)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)].

Providing and laying 80 mm thick ISI marked internlocing paver paver blocks conforming to IS 15658:2006/IRC:SP:63-2004 of all Shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159). (Note:- Reputed make Paver Block Only ISI marked will be used as approved by Engineer-in-charge).

First class brick work laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 Meter above plinth level ( HSR 11.9)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in spuer-structure. [HSR 11.48 (a)].

Terracing consisting of tiles 22.86 x 11.43 x 3.81cm. laid over 87.50 mm. mud filling on a layer of 25 mm. mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg. per Sqm. on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89).Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Not : Tile shall be of premium quality (first quality) of reputed manufacturer like:- NITCO, KAJARIA, RAK, SOMANI, JHONSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)].Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12mm thick cement plaster on walls (1:6). (HSR 15.7).

15mm Thick Cement Plaster 1:6 on the rough side of single or half brick wall. (HSR 15.12).

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52).

Cement rendering on plaster 1 mm thick.(HSR 15.75)

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3). Through Rate

Painting one coat with synthetic enamel Paint in all shades on old wood-work, or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.7). Through Rate

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge).(HSR 16.58).

Providing and Applying Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)]

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81). Through Rate

Chowkats of commercial hard wood suchas hollock, champ, chikrassy, and chaplash etc. (Non -coniferous timerb other than teak conforming to IS specification No. 1003 kin seasoned ) of doors and windows including iron hold fasts, etc, complete fixed in position (HSR 17.12)

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screw, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 30 mm thick. [HSR 17.90 (a) - Note 1 under 17.18].

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (c) decorative veneering with vertical grain cross bands and face veneer on both sides teak facing and edges lipped with commercial hard wood with laminated core:- Duro, Green Only. [HSR 17.93 - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (ii) (HSR 17.93a (i) – 30mm thick

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of of RCC including straightening, bending , binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/ storeys/basements etc. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shaal not be measured and cost of these items shall be deemed to be included in the rates for reinforcement (HSR 18.22).

Supplying and fixing glass panes including special metal sash putty of approved make (HSR 18.30 b) glass panes 4 mm thick, exceeding 40 sq dm areas. Modi, sant cabin etc.

Provding and fixing of barbed wire fancing on top of Boundary wall complete in all respect as per the direction of engineer in charge

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (b) Size 630 mm (ii) Single Colour. (Make Hindware) (HSR 30.2 b ii)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (HSR 30.12) (i) white

Providing and fixing in position best Indian make flat back or angular lipped front urinal 465 mm high consisting of :-(HSR 30.19i) Flat back lipped or angular urinal basin of vitreous china ware (to the approval of Engineer-in-charge)5 liters capacity mosquito proof Indian make C.I automatic flushing cistern, painted with non-yellow white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15mm pipe.Pair of R.S or C.I painted brackets and brass couplings Standred size G.I flush pipe with C.P brass wall clips and unions complete including cutting and making good the walls and floor and painting o fittings etc (as required by the Engineer-in-charge)i)White

Providing and fixing 25mm thnick marble partitions for different type of urinals (HSR 30.40) (B) (II) (i) vetreous Chinaware Partition plate

Providing and fixing in position best India make towel rails fixed in with rawlslugs embedded in walls with CP Brass screws, Complete in all respect including cutting and making goods the walls etc. (HSR 30.68) (d) CP Brass Two swivel towel rail 400mm longh

Providing and fixing in position best Indian make Soap dis fixed into wall with C.P. brass screws and complete in all respects including cutting and and making goods the walls etc (HSR 30.70) (d) Vitreous Chinaware recessed soap dis with hand rails (iii) Mixed Colour

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc (HSR 30.71)

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (a) Bib cock long body (HSR 30.75)

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) a) 15mm stop cock(HSR 30.76) i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully decribed in item no 30.41 above (HSR 30.42) R.S or C.I brackets for building into wall including painting 32 mm C.P brass waste with C.P brass chain and rubber plug 15 mm C.P brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-charge) All fittings best Indian make and; to the approval of the Engineer-in-chargeAll brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc.Size 530mmx430mm with one no. tap

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. 1000 Ltr. Cap. (HSR 30.119)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal Work - Exposed on Wall. [DSR 18.10). (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

(iii) 25 mm internal diameter of pipeline

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) (b) 20 mm nominal bore

(c) 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

Recovery items: Bidders have to quote rates for recovery items at least or more than reserve price. The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Note:- The reserve rate/amount is minimum amount to be used as base for quoted purchase rate by the agency. No rates/amount below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price:- Door @ 150/- Each

Window @ 200/- Each

(b) Ventilator @ Rs.100/- Each Note:- In case of any difference in the unit & nomenclature of any of the HSR items of Civil, P.H. and E.I. depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be allocable.