A/R and M/O in building maintenance under BM-I Division during 2026-27. SH Repair work at Room no 67 and 72 of ECGRF at SBS Place, Gole Market.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 gram per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and fixing of classic system Translucent fabric Roller Blinds of approved make :Hunter Douglas /D'Décor/Mac-Décor/Vista or equivalent which should be made up of 100% Polyester with Acrylic coating resistant to cracking and fraying.The fabric should be min.0.30mm (± 5%) thick and having min weight 210 g/sqmtr (± 5%). Can be installed On Face (or) Ceiling Mount (or) On Frame (or) in Recess. The Fixing Brackets are made by steel with powder coating to give greater finish. Brackets shall be accommodating overhead or side mounting with clutch assembly on either end of the blind. The ROLLER TUBE shall be of extruded anodized by non rusting Aluminum alloy with 1.25 mm thickness and 40mm in diameter. Aluminium bottom bar with powder coating or anodyzing Wall thickness: 1mm. , Height 30mm, with required width Width 10-15mm for a perfect fall of fabric to avoid warpage / floating, Installation to be insert type with end caps to give a neat look. Operating Chain: Plastic/steel ball chain (or as per manufacturer's standard) adoptable to the clutch pitch for smooth, quiet lifting & lowering of blind. The blind can be stop in desire position with help of stop lock used for raising or lowering action of the shades. The fixing angements as per approved make manufacturer specification all complete as per entire satisfaction and direction of Engineer-in-charge. (Area shall measured from bracket to bracket and from top to bottom).

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1.  The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2.  Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3.  On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4.  On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Providing and fixing S.S post including frame of grade 304 pipes with braces of S.S. grade 304 and rectangular section including cutting, organ welding, grading, making circumstances polishing, buffing etc. complete with necessary holes, nuts & bolts, caps & anchor plates of S.S. grade 304 ASTM as per drawing & instructions of the Engineer-in-charge excluding the cost of RCC/CC and earth work.

Providing and fixing retro reflective sheeting grade-XI as per ASTM-D4956-07 in single layers of approved colour over ACM/Aluminium sheet complete with necessary, adhesive and pressure method etc. The sheet layer of Type- XI sheet shall be on full face of ACM/ Aluminium sheet with words/ directions, pictogram (picture), arrows, signs shall be printed over sheet through traffic jet digital print system of approved make complete including cleaning etc. complete, all as per drawing and direction of Engineer-in-charge. (Payment shall be made for flat area of sheet only).