REPAIR MAINTENANCE AND REPLACEMENT EXTERNAL WATER SUPPLY PIPE LINE GATE VALVE SLUICE VALVE INCLUDING CLEANING OF UG OH SUMPS OTHER ASSOCIATED WORKS OF OTM ACCN OF OUTLAYING AREA UNDER GE (NW) NOFRA COLABA MUMBAI

Amount

Note : (a) Functional tools & plants shall be carried by tradesman all time for attending any site. (b) Necessary ladder / cloth or any other material reqd. (c) Debris / site clearance immediately before leaving site. (d) Safety eqpt to be carried all time. (e) In case of non-adherence of any of above fine/ penalty to be carried as under:- (i) 1st Time - Rs 200/- (ii) 2nd Time - Rs 500/- (iii) 3rd Time - Warning to contractor. (f) In case of 3 warning to contractor, it will be reflected in WLR for slow progress. (g) Complaint registered upto 11:00AM & emergency complaint to be attended same day. (h) Complaint Team consist of 02 Plumber alongwith reqd helpers.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and taking out soft/loose soil for laying of cable /erection of pole/stay pit excavation/pipe line complete all as specified and directed by Engr in Charge.

Returning and filling including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engr in Charge.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr in Charge.

Cleaning of overhead PVC tanks of capacity 500 to 2000 ltrs in existing position by mechanised pressure cleaned by Mechanical high pressure spray and steel wire brush to remove algae/dirt/foregin completely and soaking out water/dirt with a high pressure wet vaccume pump and removing spoils outside of MD land and providing sticker showing the date of cleaning complete all as specified and directed by Engineer-in-Charge

Cleaning of overhead PVC tanks of capacity 2000 to 5000 ltrs in existing position by mechanised pressure cleaned by Mechanical high pressure spray and steel wire brush to remove algae/dirt/foregin materials completely and soaking out water/dirt with a high pressure wet vaccume pump and removing spoils outside of MD land and providing sticker showing the date of cleaning complete all as specified and directed by Engineer-in-Charge

M & L for replacement of rusted /broken rubber packing both side of non return valve of CI body 80/ 100/150 mm bore Opening both side flanged with rubber packing including nuts bolts and wahsers etc complete as directed by Engr-in-Charge

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 60 to 75 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 40 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 30 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 10/15 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 05/7.5 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

M&L for disconnecting the unserviceable centrifugal/ monoblock pump set of capacity 02/03 HP any make from the pump foundation after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gasket, and replacing the unserviceable parts , gland packing, greasing, transporting back to pump house and refixing on the existing foundation, connecting the electrilc connection to the motor and testing complete to entire satisfaction of Engineer-in-Charge.

Taking down old rusted pipe including Supply and laying GI tubing 15mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 20mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 40mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 50mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 80mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 100mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

Taking down old rusted pipe including Supply and laying GI tubing 150mm dia medium grade with all fitting such as tee, socket, bend, union etc in wall/trenches complete all as specified and directed.

M&L for construction of brick masonary valve pit of minimum size 75 x 75 x 75 cm (finished internal dimensions ) and 15 mm thick on internal wall surface finished even and smooth external using extra cement and plaster in cement mortar 1:4 and painted flush externally as posible and 50 mm thick PCC 1:2:4 type B-1 for copping and fixing suitable size angle iron and MS sheet cover two side open with 2 Nos hinges each side and 2 Nos lifting handle and in built locking arrangement including lock and key and surface with two coats of synthetic black paint and a coats of red oxide paint on steel surface including necessary excavation in any type of soil, earth work in any type of soil including demolition of damaged existing valve pit complete all as specified and directed by Engr-in-Charge

Cleaning and painting external surface with cement based paint complete, colour as existing Semi under ground RCC sump of Capacity 0.10 to 0.25 lakh ltr water at pump house after draining out the water scraping out bottom and side of wall with wire brush and bleaching powder, removing scaling fungus, flushing thoroughly with clean water, applying one coat of white washing after drying inside, writing of tank capacity and date of cleaning and due date of cleaning in capital letters of 20mm size on external surface of wall with white enamel paint over black paint surface all as directed by Engr-in-Charge.

Cleaning and painting external surface with cement based paint complete, colour as existing Semi under ground RCC sump of Capacity 01 lakh ltr water at pump house after draining out the water scraping out bottom and side of wall with wire brush and bleaching powder, removing scaling fungus, flushing thoroughly with clean water, applying one coat of white washing after drying inside, writing of tank capacity and date of cleaning and due date of cleaning in capital letters of 20mm size on external surface of wall with white enamel paint over black paint surface all as directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C2 (using 20 mm graded crushed stone aggregate) for filling in hard standing/ plinth protection of semi underground tank and support to main water supply line all as directed by Engineer-in-Charge.

M&L for construction of brick masonary valve pit of minimum size 100 x 100 x 100cm (finished internal dimensions ) using sub class "B" brick masonry in cement mortar cm 1:4 including plastering internally and painted flush externally as the work proceeds and PCC 1:2:4 type B-1 as in copping with suitable size angle and MS sheet cover two side open with 2 Nos hinges each side and 2 Nos lifting handle and in built locking arrangement including lock and key and surface with two coats of synthetic black paint and a coats of red oxide paint on steel surface including necessary excavation in any type of soil, earth work in any type of soil to distance n.exc 50 m including demolition of old damaged valve pit complete all as specified and directed by Engr-in-Charge

M&L for repair to broken brick masonary valve pit of approx size 0.75 x 0.75 x 0.75 mtr to 1.1 x 1.1 x 1.1 mtr and remove the old plaster and usingmortor for plaster in cement mortar internally and painter flush externally as posible and PCC 1:2:4 type B-1 for copping and providing new MS sheet 4 mm thick cover of suitable size made of angle iron frame 40 mm x 40 mm x 6 mm with 4 mm thick MS sheet cover two side open with 2 Nos hinges each side and 2 Nos lifting handle and in built locking arrangement including lock and key and surface with two coats of synthetic black paint and a coats of red oxide paint on steel surface including necessary excavation in any type of soil, earth work in any type of soil all as specified and directed by Engr-in-Charge.

Dismantling and taking down old u/s power contractor of any make and supply and fix 3 pole power contaractor ML-4 or equivalant suitable for motor upto 40 HP complete all as specified and directed.

Dismantling and taking down old u/s power contractor of any make and supply and fix 3 pole power contaractor ML 6 or equivalant suitable for motor upto 40 to 70 HP complete all as specified and directed.

Dismantling and taking down old u/s power contractor of any make and supply and fix 3 pole power contaractor MNX 80 or equivalant suitable for motor upto 60 HP complete all as specified and directed.

Dismantling and taking down old u/s power contractor of any make and supply and fix 3 pole power contaractor MNX type or equivalant suitable for motor upto 40 HP.

Cleaning and painting external surface with cement based paint complete, colour as existing Semi under ground RCC sump of Capacity 1.5 to 3.15 lakh ltr water at pump house after draining out the water scraping out bottom and side of wall with wire brush and bleaching powder, removing scaling fungus, flushing thoroughly with clean water, applying one coat of white washing after drying inside, writing of tank capacity and date of cleaning and due date of cleaning in capital letters of 20mm size on external surface of wall with white enamel paint over black paint surface all as directed by Engr-in-Charge.

Cleaning and painting external surface with cement based paint complete, colour as existing overhead RCC tank at the top of the building up to G+15 of Capacity 10000 to 30000 ltr water after draining out the water scraping out bottom and side of wall with wire brush and bleaching powder, removing scaling fungus, flushing thoroughly with clean water, applying one coat of white washing after drying inside, writing of tank capacity and date of cleaning and due date of cleaning in capital letters of 20mm size on external surface of wall with white enamel paint over black paint surface all as directed by Engr-in-Charge

Material and labour for rewinding the electric motor of capacity 60HP to 75HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 40 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 30 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 10/15 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 05/7.5 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 02/03 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Material and labour for rewinding the electric motor of capacity 0.5/1.5 HP capacity, disconnecting the electric connection of motor, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motor from its existing position to workshop (Note:- following works deemed to be included in the quoted rates.) (a) Removing the split case/body cover of motor, seperate stator/raptor and cutting the complete burnt/defective copper winding. (b) Cleaning the stator body complete by rubbing and paper removal all carbons. (c) Insert insulating materials such as insulating paper sleeves. (d) Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temperature for achieve the particular Ohm resistance. (e) Clean the rotor and assembling in motor. (f) Connecting/coupling the motor with pump, connect all electric/earth connection foundation nuts.bolts at its original position and testing on load and complete all as specified and directed.

Taking down old unserviceable tanks any capacity Supply and fixing rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including plumber work and GI fitting included in the quoted rate at a height of bldg up to G+15 bldg complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable tanks any capacity Supply and fixing rotational moulded polyethylene water storage tanks of 1000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including plumber work and GI fitting included in the quoted rate at a height of bldg up to G+15 bldg complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable tanks any capacity Supply and fixing rotational moulded polyethylene water storage tanks of 2000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including plumber work and GI fitting included in the quoted rate at a height of bldg up to G+15 bldg complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable tanks any capacity Supply and fixing rotational moulded polyethylene water storage tanks of 3000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including plumber work and GI fitting included in the quoted rate at a height of bldg up to G+15 bldg complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable tanks any capacity Supply and fixing rotational moulded polyethylene water storage tanks of 5000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including plumber work and GI fitting included in the quoted rate at a height of bldg up to G+15 bldg complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of plastic water tank top cover double lock of capacity of tank 500 Ltr to 2000Ltr design in round shape to provide complete coverage and protection to the water tank and equipped with a closing lid mechanism ensuring secure sealing and preventing contaminants from entering the water complete all as specifed and directed by Engr in Charge.

Supply and fix in replacement of plastic water tank top cover double lock of capacity of tank 2000 Ltr to 5000Ltr design in round shape to provide complete coverage and protection to the water tank and equipped with a closing lid mechanism ensuring secure sealing and preventing contaminants from entering the water complete all as specifed and directed by Engr in Charge.

Taking out existing foot valve of any size from underground tank and disconnecting from the suction pipe including cleaning the same if in serviceable condition then refixing in the same postion complete all as specified and directed by Engr in Charge.

S&F in replacement of unserviceable sluice valve with new sluice valve flanged type with brass spindle including rubber, packing materials, nut, bolts and washers with locking arrangement in such a way that the valve can be locked in its open position ISI marked on body conforming to IS-14846 PN-1.6 of size 80 mm dia all as directed by EIC.

S&F in replacement of unserviceable sluice valve with new sluice valve flanged type with brass spindle including rubber, packing materials, nut, bolts and washers with locking arrangement in such a way that the valve can be locked in its open position ISI marked on body conforming to IS-14846 PN-1.6 of size 100 mm dia all as directed by EIC.

S&F in replacement of unserviceable sluice valve with new sluice valve flanged type with brass spindle including rubber, packing materials, nut, bolts and washers with locking arrangement in such a way that the valve can be locked in its open position ISI marked on body conforming to IS-14846 PN-1.6 of size 150 mm dia all as directed by EIC.

S&F in replacement of unserviceable sluice valve with new sluice valve flanged type with brass spindle including rubber, packing materials, nut, bolts and washers with locking arrangement in such a way that the valve can be locked in its open position ISI marked on body conforming to IS-14846 PN-1.6 of size 200 mm dia all as directed by EIC.

Supply and fix foot valve, 50 mm size PN-1.6 pressure rating including all joints with rubber or fibre board, bolts, nuts washers, etc including taking down old unserviceable foot valve complete all as specified and directed by Engr-in-Charge.

Supply and fix foot valve, 80 mm size PN-1.6 pressure rating including all joints with rubber or fibre board, bolts, nuts washers, etc including taking down old unserviceable foot valve complete all as specified and directed by Engr-in-Charge.

Supply and fix foot valve, 100 mm size PN-1.6 pressure rating including all joints with rubber or fibre board, bolts, nuts washers, etc including taking down old unserviceable foot valve complete all as specified and directed by Engr-in-Charge.

Supply and fix foot valve, 150 mm size PN-1.6 pressure rating including all joints with rubber or fibre board, bolts, nuts washers, etc including taking down old unserviceable foot valve complete all as specified and directed by Engr-in-Charge.

Supply and fixing of water level indicator one Nos of each semi under ground sump with all accessories i.e Angle iron of suitable size including welding work wire as required gauge, PVC cane/drum , moving roller , welding work etc and one coat of synthetic enamel black paint front / back side and written / marking level gauge with white /red paint with all necessary safety equipment, helmet, ladder, rope, safety belt etc provided by contractor , complete all as specified and directed by Engineer-in-charge.

M&L for Painting of CI/GI pipe line 40 mm to 150mm inside the pump house and out side each pump house and all sluice valve, NRV gate valve with one coat of synthetic enamel black/gray paint of existing colour shade with spray gun machine and after cleaning and preparation of surfaces complete all as specified & directed by Engr-in-Charge

Taking down the broken iron coupling from 60 HP to 75 HP motor / pump and fixing the new coupling with cotter pin, rubber piece and nut bolts as per sample complete all as specified and directed by Engr in Charge.

Taking down the broken iron coupling from 40 HP to 60 HP motor / pump and fixing the new coupling with cotter pin, rubber piece and nut bolts as per sample complete all as specified and directed by Engr in Charge.

Taking down old iron coupling from 5 HP to 30 HP motor / pump and fixing the new coupling with cotter pin, rubber piece and nut bolts as per sample complete all as specified and directed by Engr in Charge.

Taking down old rubber coupling from the 60 HP to 75 HP motor / pump and supply and fixing the new coupling with rubber piece and nut bolts complete all as specified and directed by Engr in Charge.

Taking down old rubber coupling from the 40 HP to 60 HP motor / pump and supply and fixing the new coupling with rubber piece and nut bolts complete all as specified and directed by Engr in Charge.

Taking down the old rubber coupling from the 5 HP to 30 HP motor / pump and supply and fixing the new coupling with rubber piece and nut bolts complete all as specified and directed by Engr in Charge.

S&F in replacement non return valve of CI body 80 mm to 100 mm bore flanged with rubber packing including nuts bolts and wahsers etc complete as directed by EIC.

S&F in replacement non return valve of CI body 150 mm to 200 mm bore flanged with rubber packing including nuts bolts and wahsers etc complete as directed by EIC.

Taking out Old rusted and broken Fresh water tank lid and supply and fix new cast iron lid including locking arrangements black paint in /out side fixed on RCC water tank on top of building cap of tank 20000 gallons capacity as directed by EIC.

M & L for dismantling the rusted foundation bed of the motor and pump set, and fabrication of the foundation beds with MS channels angle of the required size as per pump set capacity (40 HP to 75 HP) and duly applying one coat of red oxide primer and two coat of bitumen paint of approved quality and erection of pump and motor testing to the entire satisfaction of Engineer-in-Charge. [Note:- (a) Quoted rate is deemed to be included for welding work, nuts, bolts, washer and MS fasteners including Concrete required for foundation].

M & L for dismantling the rusted foundation bed of the motor and pump set, and fabrication of the foundation beds with MS channels angle of the required size as per pump set capacity (20 HP to 40 HP) and duly applying one coat of red oxide primer and two coat of bitumen paint of approved quality and erection of pump and motor testing to the entire satisfaction of Engineer-in-Charge. [Note:- (a) Quoted rate is deemed to be included for welding work, nuts, bolts, washer and MS fasteners including Concrete required for foundation].

Supply, fixing and testing water meter suitable to fit in 80/100/150mm bore in existing GI/CI pipe complete with flange, gasket, nuts, bolts and all necessary required items all as specified and directed by Engineer-in-Charge.

Repair/Maintenance to Chlorine dozing system assembly with chlorine injector dozing pump, cleaning, servicing, carrying out minor repairs and testing. [Note : (a) Quoted rate deemed to be inclusive of consumables item like cotton waste cloth etc. (b) spare parts required to be replaced.]

Supply & fix in replacement of dosing Pump high pressure single head gear motored adjustable dosing pump with accessories include lead tubing, connecting nuts, injection check valve, clay weight, ferules etc complete all as specifed and directed by Engr in Charge.

Supply and Fix in replacement of dosing system consisting 40 ltr-100 ltr PE/FRP Tank with PE/FRP Lid & level gauge along with agitator with shaft & blade in plastic tank complete all as specified and directed by Engr in Charge.

Disconnecting all electric connections from the chlorine dosizing motor 1.5 HP & taking out and rewinding the same motor with copper winding and refixing the same postion and testing complete all as specified and directed by Engr in Charge.

Supply and fix in replacement of new butterfly valve of PN 1.0 of dia 80mm complete all as specified and directed by Engr in Charge.

Supply and fix in replacement of new butterfly valve of PN 1.0 of dia 100mm complete all as specified and directed by Engr in Charge.

Supply and fix in replacement of new butterfly valve of PN 1.0 of dia 150mm complete all as specified and directed by Engr in Charge.

Supply and fix in replacement 40 mm gun metal globe or gate valves, with iron whel head, screwed both endes for iron pipe complete all as specified and directed by Engr in Charge.

Supply and fix in replacement 50mm gun metal globe or gate valves, with iron whel head, screwed both endes for iron pipe complete all as specified and directed by Engr in Charge.

Supply and fix in replacement 80 mm gun metal globe or gate valves, with iron whel head, screwed both endes for iron pipe complete all as specified and directed by Engr in Charge.

M&L for disconnecting all electric connections from the submersible pump & motor 03 HP and taking out column assembly from bore well and transporting the same to civil workshop for repair including winding etc complete all as specified and directed by Engr in Charge.

Disconnect the electric connections form starter and taking out burnt submersible starter from the existing position and supply and fixing new water sensor, starter 3 phase of 10HP , 440 Volt , front side openable and locking arrangement all as per directed by Engr- in-Charge .

M&L for attending leakage complaints in pump house/ high rise building by checking centrifugal pump / NRV / sluice valve/Non return valve/gate valve of pipe line leakage including replacement of unserviceable component including preventive maintinance spares by replacing minor parts i.e gland packing nut and bolts complete all as specified and as directed. [Note:- If the contractor will not attend the complaints by his trades man in any working day /holiday including sunday the necessary reovery of Rs. 500/- per day shall be imposed complete all as specified and directed by Engr in Charge]

Taking down rusted/leakage not greater than 3 mtrs of size 100mm GI suction pipe from the existing position pump house and replace with new GI pipe line of size 100 mm by threading / welding work /bend /flanged /nut, bolts/ labour charge all as directed by EIC.

M&L for welding work any type Gas welding/ electric welding for GI/MS pipe/angle iron etc complete all as specified and directed by Engr in Charge

Supply and fix in replacement of bronze impeller suitable for 60/75 HP pump all as per manufacturer's design as per staging and eye of the impeller complete all as per specified and directed.

Supply and fix in replacement of bronze impeller suitable for 40 HP pump all as per manufacturer's design as per staging and eye of the impeller complete all as per specified and directed.

Dismantling of Damaged/Burnt MCCB and Supply & fixing of MCCB,3 Pole, 630 Amps, 36kA, 415Volts,50Hz AC s complete all as specified and directed by Engr-in-charge.

Dismantling of Damaged/Burnt MCCB and Supply & fixing of MCCB,3 Pole, 200 Amps, 25kA, 415Volts,50Hz AC s complete all as specified and directed by Engr-in-charge.

Dismantling of Damaged/Burnt MCCB and Supply & fixing of MCCB,3 Pole, 160 Amps, 25kA, 415Volts,50Hz AC s complete all as specified and directed by Engr-in-charge.

Taking down old pipe and Supply and laying MS pipe 100 mm dia in wall/ trenches alongwith all fittings such as tee,bend, socket, etc complete all as specified and directed by Engr in Charge.

Material and labour for scrubbing old paints from outer surface of plants and equipment including painting with two coat of synthetic enameled paint over one coat of red oxide paint and also writig AM/MES Nos on surface of the pump motor set from 2 HP to 10 HP with white paint including delivery pipe of any size upto 15 RM complete all as specifed and directed by Engineer- in -Charge.

Material and labour for scrubbing old paints from outer surface of plants and equipment including painting with two coat of synthetic enameled paint over one coat of red oxide paint and also writig AM/MES Nos on surface of the pump motor set from 15 HP to 60 HP with white paint including delivery pipe of any size upto 15 RM complete all as specifed and directed by Engineer- in -Charge.

Material and labour for scrubbing old paints from outer surface of plants and equipment including painting with two coat of synthetic enamel paint over one coat of red oxide paint of LT panel of pump house complete all as specifed and directed by Engineer- in -Charge.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below normal ground level connected with galvanized iron earth lead strip of 32x6mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 15mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC 1:2:4 in pit with pre- cast RCC 1:2:4 cover reinforced with XPM not less than 4 Kg Sqm, test point etc. all as shown in electric plate No. 3 of SSR Part-I complete with necessary earth work in any type of soil, removal to a distance not exc. 50m, testing on completion complete all as specified and directed by Engineer-in-Charge

M&L for Replacement Earth continuity conductor or main earthing strip of size 32 x 6 mm fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to pole complete all as specified and directed by Engr in Charge.

Cleaning and painting external surface with cement based paint complete, colour as existing Semi under ground RCC sump of Capacity 0.30 to 0.50 lakh ltr water at pump house after draining out the water scraping out bottom and side of wall with wire brush and bleaching powder, removing scaling fungus, flushing thoroughly with clean water, applying on coat of white washing after drying inside, writing of tank capacity and date of cleaning and due date of cleaning in capital letters of 20mm size on external surface of wall with white enamel paint over black paint surface all as directed by Engr-in-Charge

Unity Enterprises (BID ID -3107379)

ASHOK ENTERPRISES (BID ID -3103283)

SHRI SAI ENTERPRISES (BID ID -3106188)

B P ENTERPRISES (BID ID -3106826)

P LAXMI AND CO. (BID ID -3107023)

M K ENTERPRISES (BID ID -3106720)

Rama Construction Co (BID ID -3105743)

GANGAJAL (BID ID -3121021)