CA NO. GE (I) (AF)/SHL/ OF 2020-2021 REPAIR/ MAINTENANCE OF RCC ROOF, LEAKAGE SEEPAGE OF WALL, FLOOR/WALL TILES, JOINERY, SANITARY AND PLUMBING FITTING, PLINTH INCLUDING INTERNAL ELETRIFICATION AND MISC WORK TO OFFICERS ACCOMODATION AT HQ EAC (U) UN

Amount

Note : All unserviceable materials obtained out of demolition/dismantling/taking down (other than those for which credit catered under Schedule of credit) shall be disposed of outside MoD Land. Quoted rates against respective item shall deemed to include for same.

B/R ITEMS Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material complete all as specified directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed.

Demolition of unreinforced cement concrete in any position not otherwise specifically provided for and removal all rubbish material complete all as specified and directed.

Dismantling of timber fillet, rails, post, rafters, purlins, etc. under 40 Sqcm in section unframed or framed work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area not exc. 1 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area exc. 1 sqm & n.exc 2.00 sqm each complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses etc complete all as specified and directed.

Taking down existing roof treatment including PCC padding over roof, removing complete layer of bitumen under PCC padding, cement mortar & felt cleaning the surface by hacking to receive plaster and removing demolished material outside MD land complete all as specified and directed.

Dismantling plain or corrugated steel sheeting/galvalume sheet any guage, thickness including Nainital or similar pattern roof covering,complete all as specified and directed

Dismantling fibre glass reinforced translucent corrugated sheeting any thickness in roof covering,complete all as specified and directed

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beeds complete all as specified and directed.

Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site complete all as specified and directed .

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. (Note :- The length shall be measured along the centre line including fittings and accessoires).

M&L for pre-cast cement concrete block masonry 1:3:6 Type C-1 using 20mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

M&L for cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands copping/cills, bed block for embedding hold fast etc including necessary form work weathering, slightly rounded or chamfered angles and throating complete all as directed .

Supply only integral water proofing liquid complete all as directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads section area exc 13 Sqcm but n.exc 25 Sqcm complete all as specified and directed.

M & L for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and directed.

S & F of 40mm thick second class hardwood (CHIR) boarding as in floors and skirting planed one side and edges tongued and grooved or rebated and fixed with nails complete all as specified and directed.

M & L for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35mm thick IInd Class Hard wood, plain framed, panelled door shutters, two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces (as ordered). The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 35mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 30mm thick glazed and skeleton window/door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8.24(b) and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, In opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed for following sizes:-

75 mm long.

100mm long.

S & F 100mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 200mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 100mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolts, plate type with bolt not less than 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as directed

S & F 100mm size brass handles cast type polished bright fixed with screws.complete all as specified and directed.

S & F in repairs continuous (Piano) hinges width of flaps (when open) 40mm, MS, bright finish or electro galvanised complete all as specified and directed.

BLANK

S & F in repairs ball catches with 8mm dia steel ball and brass body and skirting plate including letting in and fixed complete all as specified and directed.

S & F in repairs 100mm size brass mortice lock vertical type with 4 lever complete all as specified and directed.

S & F in repairs aluminium (Die cast) body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as directed.

S & F in repair for powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends fixed with PVC rawl plug and steel screws on walls/beam, complete all as directed.

S & F in repairs of Chromium plated Knob (mini round handle) for drawer (of kitchen CB/books shelfs) complete all as specified and directed.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S&F mild steel work in tubular trusses, purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161 grade St-240 including notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts including rivets or nuts and bolts, providing and fixing cleats, fish plates, gusset plates etc and also for wedging, plumbing, turning up & fixing complete all as specified and directed.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) anodized aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium door shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated aluminium fittings, such as handle (01 No for each leaf) etc complete all as specified and directed. (Note :- Glazing/wire mesh shall be measured and paid separately under respective items of Schedule.)

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium windows and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated anodised aluminium fittings such as peg stays 150mm long (01 No. for each leaf), Butt hinges type B-21 100mm size (02 Nos for each leaf) & handle (01 No for each leaf) etc complete all as specified and directed. (Note :- Glazing/wire mesh shall be measured and paid separately under respective items of Schedule.)

S & F in repairs powder coated aluminium grills for window/ ventilator solid mesh type not less than 3 Kg per Sqm area of approved pattern including edging with solid 'C' channel and fixing in position complete all as directed and specified.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm , black finish reinforced with non-woven polyester reinforcement matt, with a thermo fusable finish laid over compatible cold emulsion bituminous primer applied at the rate of 0.40 Kg/Sqm by torching with a propane or a butane gas torch, with a overlap of 75mm on longitudinal direction and 100mm on transverse direction including sealing all as per manufacturer’s instructions complete all as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 100 Gms/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

S & F for pre-painted galvalume aluminum zinc coating GI based trapizoidal profile steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions completed all as specified and directed.

S & F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in lieu of screw using profiled GI washer and bitumen washer in roof covering complete all as specifed and directed.

S & F 4mm thick non-asbestos fibre cement building board, fixed to timber framework with screws as in ceiling complete all as specified and directed.

M & L for providing and fixing suspended false ceiling make Armstrong ORCAL extra micro perforation or equivalent of size 600 x 600 x 15 mm ceilling tiles over suspension metal system (MICRO LOOK) designer grid (15 mm grid 8 mm return) SILHOUETTE XL 15 mm (NOMINAL) of Armstrong make complete index no. DUNE RH 99 (or equivalent of makes listed in List of makes) including necessary hanging arrangement as per manufactures instruction complete all as directed.

S & F 12mm thick toughened glass sliding door alogwith necessary guide channels, rollers, including necessary one/two way spider with spider fin glazing system and with provision of stainless steel handles and necessary fittings complete all specified and directed.

S & F in repairs 6mm thick plywood, (5 ply), grade BWR, type BB, fixed with screws to timber frame work/walls complete all as specified and directed.

S & F in repairs 18/19 mm thick Prelaminated particle, board, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination and alround covered with 6mm thick teak wood beading/lipping fixed with screwed to timber frame complete all as directed.

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement complete all as specified and directed.

Material and labour for 5mm thick PVC sheet fillet of width 35mm for wall panelling and the like including fixing to walls to make PVC frame or as required complete all as specified and directed.

S & F anti fungal and anti bacterial PVC digitally multi colour wall planks of size 255mm width and 3050mm length of thickness 6mm. Both parallel long sides should have interlocking edges of 15mm with 8mm groove. The planks should be fixed in 25x40x1.5mm aluminium square pipe with 19 x 6mm steel screw. The edges should be moulded with 19mm thick PVC U-profile of 3050mm length and adjacent joint should be connected with PVC-H profile the same colour of the steel of size 20x3050mm. The L corners of the design should be moulded with PVC L-Profile of 19x19x3050mm length fixed with instant fixing glue, the PVC Planks must be fire retardant and match the BS 476 point 6 & 7 (BIS. 12777 : 1989) The aluminium flame work must be made minimum 450mm and maximum of 600mm Perpendicular of the sheet fixed on the wall with 75x10mm screw complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in levelling coarse of floors, surfaces finished even and fair complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M & L vitrified ceramic tiles dark shade 10mm thick (square/rectangular) area of each tile exceeding 0.42 sqm but not exc 1.00 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M & L for Pavement floor vitrified tiles of size exc 0.09 Sqm but not exc 0.36 Sqm 10mm thick (Endura tiles of Johnson or equivalent makes listed in List of Makes) set & jointed in neat cement slurry and pointed with grey cement and pigment to match the colour of tiles in floor complete all as specified and directed.

M & L for prepolished cement concrete chequered tiles of size 400 x 400 x 25 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L 20 mm thick granite slab/tiles (of any type table rubbed and polished) in steps jambs pillars, window cills, cooking platforms and like set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with complete all as specified and directed.

M & L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM 1:4 on fair faces of brick masonry/concrete surfaces, mixed with water proofing liquid @ 150ml per 50 Kg bag of cement and finished even and smooth without using extra cement complete all as specified and directed. (Note :- Supply only Water Proofing Liquid shall be measured and paid separately)

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exceeding 0.36 sqm, as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for joint less, coloured dark shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles exceeding 0.42 sqm but not exc 1.00 sqm, as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all specified and as directed.

S & F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in squares exc 0.5 sqm in each pane complete all specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1mm thick wall care putty complete all as directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

M & L for preparing old plastered surfaces of wall and applying one coat of oil bound distemper complete all as per specified and directed.

Material and labour for preparation of newly plastered surfaces of wall, applying a coat of 1mm thick wall care putty and applying two coats of weather proof acrylic paint over one coat of exterior grade acrylic primer complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Beger, Acroguard 3X of Acro paint.

M&L for preparing surface of timber piles and dipping in a hot mixture of tar and creosote in the proportion of 20 kg coal tar pitch to 25 litres of creosote oil for 4 mins complete all as specified and directed.

M & L for French Polishing on wooden or wood based surfaces surfaces of any description width or girth including cleaning and preparing the new surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

M & L for French Polishing on old wooden or wood based surfaces of any description width or girth including cleaning and preparing the old surface with two or more coats complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed for following sizes:-

75mm bore

110mm bore

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed for following sizes:-

75mm bore

110mm bore

S & F PVC (SWR) bend of any radius with oval access door complete all as specified for following sizes:-

75mm bore

110mm bore

S & F PVC (SWR) 110mm junction, single (single T) equal or unequal complete all as specified and directed .

S & F PVC (SWR) vent cowl for 75 mm bore of pipe complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Fixing only old serviceable steel water tubing, galvanized, medium grade, with all new fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

S & F 15mm bore bib tap cast copper alloy fancy type chromium plated long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore stop valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

M & L in repair for 15 mm dia cast copper alloy Chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8712 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs 15 mm dia cast copper alloy Chromium plated one way Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8710 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs 15 mm dia cast copper alloy Chromium plated two way Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8711 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair 15 mm dia Brass CP, wall mixer 3 in 1 system with provision for both hand and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange (without Hand and overhead shower) (Concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-281KN of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs 15mm bore sink mixture for mixing hot and cold water chromium plated fancy type with swinging casted spout (wall mounted model) with connecting legs & wall flanges two joints to steel pipe or union and plugging/screwing to wall complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-309KN of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs 15mm bore central hole Basin mixture for mixing hot and cold water chromium plated fancy type without popup waste system with 450mm long barided hoses complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-167KNB of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs Hand Shower (Health Faucet) with 8mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed. (Product Code & Make :- Cat Part No ALD-573 of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs Hand Shower of 95mm dia round shape multi flow (ABS body chrome plated with grey face plate) with rubit cleaning system with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. (Product Code & Make :- Cat Part No HSH-1739 of JAQUAR or equivalent model of KOHLAR/Roca) (Product Code & Make :- Cat Part No HSH-1739 of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repair vitreous China urinals with sensor of size 720mm x 485mm x 310mm, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including long brass screws, pointing around urinal back in cement; and union for dishcharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed. (Product Code & Make :- Cat Part No URS-WHT-0704 for Urinal and Cat Part No SNR-51097 for Sensor Kit of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs white Vitreous china wash down water closet pan (pedestal pattern) with integral S trap including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) etc complete all as specified and directed. (Product Code & Make :- Cat Part No CNS-WHT-WH-10 of JAQUAR or equivalent model of other makes listed in list of makes).

S&F in repair single piece Suite white Vitreous china wash down water closet pan (pedestal pattern) with integral Vitreous china flushing vistern including plastic water closet seat and cover,complete all as specified and directed. (Product Code & Make :- Cat Part No C844A Qube of Parryware or equivalent model of other makes listed in list of makes).

S & F in repair chromium plated 32mm size bottle trap (with internal partition) with 300mm & 190mm long wall connection pipes & wall flange complete all as specified and directed. (Product Code & Make :- Cat Part No ALD-769L300x190 of JAQUAR or equivalent model of other makes listed in list of makes).

S&F in repairs chromium plated towel rail complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-40 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repair Stainless steel Towel rack 600mm long without lower hangers, fixed to walls with brass screws complete all as specified and directed. (Product Code & Make :- Cat Part No ACN-1181S of JAQUAR or equivalent model of other makes listed in list of makes).

S&F in repairs chromium plated toilet paper holder with flap complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-38 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs CP Soap Dispenser with glass bottle complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-33 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs glass shelf 500 x 125mm with decorative and ornamental side supports and front lining of chromium plated fixed with screws and glass with as shelf supported over frames all as specified and all as directed. (Product Code & Make :- Cat Part No. BEA-45 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair corner glass self of size 300mm radius (with brass chromium plated brackets) fixed in the walls with necessary screws etc. complete all as specified and directed. ((Product Code & Make :- Cat Part No. BEA-44 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs PTMT alloy toilet cabinet with mirror of overall size 622 x 422mm and fixed to wall complete all as specified and directed. (Product Code & Make :- Cat Part No. 556 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs MDF wall hung vanity cabinets of size 900x800mm complete all as specified and directed. (Product Code & Make :- Cat Part No. C846K46 for Mirror & C846J46 for Base cabinet of Make Parry ware or equivalent model of other makes listed in list of makes).

S & F in repairs shower panel of size 1550x150mm complete all as specified and directed. (Product Code & Make :- Cat Part No. C841U99 Fraser of Make Parry ware or equivalent model of other makes listed in list of makes).

S & F in repairs corner entry shower enclosure of size 1200x1200mm complete all as specified and directed. (Product Code & Make :- Cat Part No. Kretana of Make Jaquar or equivalent model of other makes listed in list of makes). (Note : The contractor shall deposit with Engineer-in-Charge these original purchase voucher and product guarantee/warrantee certificate in original for the period as per policy in vogue of manufacturer to obtain service from manufacturer during the period of guarantee/warrantee.)

S & F in repairs for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm dia complete all as specified and directed.

S & F in repairs PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen sink with plugs, washers and wastes, including bedding cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, over all size 915mm x 460mm bowl size 410 x 330mm x 160mm, complete all as specified and as directed.

S & F 500 litres capacity rotational moulded HDPE water storage tank tripple layer (Cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. Note : PVC tanks shall be ISI marked and having two layers.

M&L for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnectings and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres complete all as specified and directed.

S & F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

S & F in repairs vitreous china wash basin OVAL type of size 195x600x425mm with 16 to 18mm thick granite counter including cutting for and pinning in ends for bracket, and waste fittings 32mm including waste pipe, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed. Note : Granite stone for counter shall be measured and paid separately under respective item of BOQ.

S & F in repairs PVC (SWR) floor trap 75mm dia outlet plain with Stainless steel grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as directed.

Demolition existing unserviceable salt-glazed stoneware gully traps of any size including surrounding packing and M & L for PVC(SWR) gully trap 125/110 mm, setting and jointing with solvent cement including provision of 150 mm thick PCC 1:4:8 type D-2 (40 mm graded aggregate ) all round & at bottom of trap complete all as specified and directed.

S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repairs plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

E/M ITEMS Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete from existing conduits, from PVC Casing/capping with all fittings, such as switches, ceiling rose, pendants, sockets, lamp holder, fan regulators, sketch/brackets light fittings (except tube light fitting) etc and removal of old material from site (except switches, sockets and fittings to be reused) and making good disturbed surfaces of walls, floors ceiling etc complete all as specified and directed to match with existing surfaces.

Taking down old tube light fittings/light fittings/security lights any type and removal of old light fittings from site (except light fittings to be reused) and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed to match with existing surfaces.

M & L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable drawn through and including PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS, including 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H green colour cable as earth continuity conductor to common earth & connecting to earth dolly for the following :- (Note : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces. )

One light point/fan point controlled by one, one way switch.

M & L for point wiring complete for 5 Amps socket outlet on independent board with 2.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable drawn through and including PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS, including 2.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H green colour cable as earth continuity conductor to common earth & connecting to earth dolly. Notes : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces.

M & L for point wiring complete for 15 Amps socket outlet on independent board with 4 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable drawn through and including PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS, including 4 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H green colour cable as earth continuity conductor to common earth & connecting to earth dolly. Notes : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces.

M & L for modular metal flush box for the following modules :-

1 Module

3 Module

4 Module

6 Module

8 Module

M & L for modular white cover plate with frame for the following modules :-

1 Module

3 Module

4 Module

6 Module

8 Module

S & F modular switch, 1 way 6A, 240 Volts, 1 module complete all as specified and directed.

S & F modular bell push, 1 way 6A, 240 Volts, 1 module complete all as specified and directed.

S & F modular switch, 1 way 16A 240 Volts, 1 module complete all as specified and directed.

S & F, modular socket outlet for two and three pin combined, 6 Amp, 240 Volts, 2 Module type complete all as specified & directed.

S & F, modular socket outlet for two in one, three pin combined, 6 & 16 Amp, 240 Volts, 2 Module type complete all as specified & directed.

S & F bell Ding-dong type, AC, 230 Volts, single pole complete all as specified & directed.

S & F ceiling rose, three terminal, PVC / poly carbonate isolated body, complete all as specified and directed.

Supply and fix 12 watt Round shaped recess LED HPF flat panel with a high output comprises of aluminium die cast housing finished in powder coated, High translucent frosted PMMA diffuser is used to get glare free smooth light distribution and connecting the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. {Model/Make : Cat Part No. LSCRM-12W-CDL/NW/WW of make Crompton or equivalent model of makes listed in List makes}.

S & F high efficiency LED recess bottom opening light fittings, 40 Watt, 5700K, 300 x 600mm size, with super bright LEDs with highly efficient light smoothing optics, suitable for ceiling/POP utilisations with all accessories and fixing arrangements complete all as specified and directed. {Model/Make : Cat Part No LCBOR-40-CDL(1x2) of make Crompton or equivalent model of makes listed in List makes}.

S & F high efficiency LED recessfull open light fittings, 36 Watt, 5700K, 605 x 605mm size, with super bright LEDs with highly efficient light smoothing optics, longer life and less maintenance with all accessories and fixing arrangements complete all as specified and directed. {Model/Make : Cat Part No LCTLRN-36-FO-CDL of make Crompton or equivalent model of makes listed in List makes}.

Supply and fix 6 watt LED spot light ideal for wardrobes with aluminium housing with bracket and clamp for wall mounting arrangments and connecting the fitting using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. {Model/Make : Cat Part No. LCSRR-6-CDL/TL/WW of make Crompton or equivalent model of makes listed in List makes}.

Supply and fix pendant, champagne opal glass & chrome finish LED wall lamp complete all as specified and directed. {Model/Make : Cat Part No. KCH-CHR-MB150330031A of make Jaquar or equivalent model of makes listed in List makes}.

R K CONSTRUCTION

M/S BISWA CONSTRUCTION

M/s Gupta Construction