Special Repair to Offr Mess and Single offrs accn of SCN Bldg No T-169 T-170 T-171 and 172 under GE East

Amount

Dismatnling of asbestos cement(corrugated, semi-corrugated or plain) sheet as in roof coverings complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridge, fixed with self tapping screws complete all as specifed and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F Rolled mild steel work in roof trusses (framed),trussed, purlins, rafters,crane gantries and heavy brackets framing (beams,tee,angle,channel or flat section) including MS plates, nutt bolts etc complete conforming to Fe 410-W(Gde, E-250) Quality A complete all as specified and directed.

Dismantling wall and ceiling boards(fibre,pulp, uninsulation etc) or unsulation boards/slabs/blankets any thickness including cover fillet complete all as specified and directed.

Supply and fixing false ceiling with Everest fibre cement designer tile ivory painted (high pressure steam cured) of 4mm thickness (as per IS : 14862) of size 595 x 595mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking meta grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main ‘T’ runner with suitably spaced joints to get required length and 15 x 32mm made from 0.3mm thick sheet and cross ‘T’ of size 15 x 32mm made of 0.30mm sheet, spaced between main ‘T’ at 600mm c/c to form a grid of 600 x 600mm and wall angle of size 15 x 20mm made of 0.30mm thick sheet and laying false ceiling tiles in the grid including, required cutting/ making, opening for services like diffusers, grills, light fitting, fixtures, smoke detectors etc. main ‘T’ runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main ‘T’ bottom exposed width of 15mm of all T-sections shall be center black pre-painted with polyester paint and having a load bearing capacity of 12 Kg/ Sqm complete all as specified and directed.

S&F for Solid PVC Wall Lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets or metal frame work and reinforced with GI wire mesh (fillets, metal frame work and GI wire mesh paid seperately)

Ditto- but to curved surface.

Extra over item no 10&11 for any sunk and raised moulding.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for Virified Ceramic tiles light shed 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 20 mm thick cement screed bedding layer in cement mortar 1:6 complete all as specified and directed.

All as per item 14 above but on vertical surfaces such as skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:3) complete all as specified.

M&L for non skid joint free ceramic coloured tiles of area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm and 7-8 mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x200x7/450x350x7mm thick fixed with neat cement slurry in vertical surface to wall and pointed in white/coloured cement to match over and including 10mm thick rendering in CM 1:4, all as specified and directed.

M&L for 20 to 25 mm thick Kota stone slab flooring laid over 15 mm thick screed bed of CM (1:3) mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

All as per item 18 above but on vertical surfaces such as skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:3) complete all as specified.

M&L for 16/18mm thick Udaipur green stone polished stone over and including minimum 10 mm thick screed bed in cm (1:3) and jointed with neat cement slurry mixed with pigment to match the colour of stone complete all as specified and directed.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms, shelves in cupboard,handwash places and like including necessary cutting and grooving to walls and making good by pointing in cement mortar (1:2) using admixture of pigment to match with shade of granite over and including 10 mm thick rendering in (1:3) all as specified and directed.

Taking down cement plaster or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc any description complete all as specified and directed.

M&L 15mm thick cement plaster in cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick cement plaster in cement mortar 1:4 on brick or concrete surface with water proofing compound finished even and fair without using extra cement all as specified

Supply only Integral waterproofing compound supplied only complete all as specified and directed.

M&L for prepration of new plaster surfaces of walls and applying two coats of oil bound distemper including a coat of primer on plastered surfaces over 2mm thick two coat of Birla White Putty complete allas specified.

M&L for preparation of new plastered surfaces of wall surfaces and applying two coats of Acrylic exterior plastic emultion paint over a coat of wall primer (X2) complete all as per manufacturer instruction and as specified and directed by Engr-in-Charge.

M&L for preparing new plastered or unplastered wall surfaces and applied two coat of cement base paint complete all as specified and directed.

M&L for prepration of old steel surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applied two coat of synthetic enamel paint over one coat of red oxidezinc chrome primer complete all as specified and directed.

Taking down chowkats or frame not exc. 1.5 sq m each with shutters (without taking off shutters from the fames) complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 sq m but n.exc 4 sq m each with shutters (without taking off shutters from the fames) complete all as specified and directed.

M&L powder coated aluminium door shutter having 150mm x 44mm x 2.85 mm thick bottom rail, 150 mm x 44mm x 2.85mm thick middle rail, 100mm x44mm x3 mm thick stile and top rail including necessary fitting joinery cleat, glazing packing snap beading 10 mm x 10 mm ,anodixed aluminium handle 200 mm long (02 Nos) , 3 Nos 100 mm size chromium plasted butt hinges, 2 Nos 200mm size Alu tower bolt and Aluminium body hydraulically door closer , designation No-3, universal type, weight between 61 to 80 kg etc inlcuding frame of section 100 mm x 44 mm x3 mm and door shutter, bottom portion covered with 9mm thick prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination (colour/design approved by Engr-in-Charge) fixed to Aluminium frame work and top portion covered with 5.00 mm thick float glass and pattern, one mortion lock (Make: Harrison ) with shutter and fixing complete all as specifies and directed by Engineer-in-Charge.

M&L powder coated aluminium window/ ventilator shutter side hung having 75 mm x 44 mm x 2.85 mm thick stiles bottom rail and top rail including necessary ftting joinery cleat glasing packing snap beading 10 mm x 10 mm , 2 nos of anodixed aluminium handle 150 mm size, 2 nos of chromium pated butt hinges 75 mm size and 2 nos of 100 mm long Alu tower bolt etc inlcuding frame of section 100 mm x 44 mm x 3 mm and including 5.00 mm thick float glass and fixing complete all as specified & directed by Engineer-in-Charge.

Supplying and fixing steel windows 1.25 mm thick Box type (primer coated) ERW hollow 'P' section of size 60 mm x 25 mm single rebated comprises of glazed sutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf conisting two Nos sash bar of 'T' section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWR bot 'T' section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1, four Nos for each window including following fittings welded to failed shutter:- (a) Holdfasts 150 mm long 12mm x 3 mm made to shape- 4 Nos per window (b) Handle of Z sec 20 mm x 25 mm, 100 mm long - 1 nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) 'Z' sec 20 mm x 25 mm , 100 long stopper-01 Nos per leaf, (e) Cleat 55mm long of hollow square 15 mm x 20 mm x 63 mm welded to hinges - 1 Nos per leaf (f) MS pintal hinges of size 75 mm x 12 mm - 2 Nos per leaf. (g) fabriction and fixing arrangement complete. Note:- (i) Grill / guard war , glass pane shall be measured and Paid saperately. (ii) CEJZ Drg No CEJZ/TD-1019/08 (Sheet 1/3 to 3/3) shall be followed.

All as per description of serial item No. 35 above but in gauged shutters without sash bars all as specified and directed. Note:-Drawing No CEJZ Drg No CEJZ/TD-1020/08 (Sheet 1/3 to 3/3) shall be followed.

All as per description of serial item No. 35 above but in ventilators fixed type. Note:-Drawing No CEJZ Drg No CEJZ/TD-1024/08 (Sheet 1/1R) shall be followed.

S&F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars barallel iron doors and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and directed.

M&L for 4.00 mm thick glass sheet, ordinary quality and glazing with oil putty in square n. exc 0.5 sq. m in each pane complete all as specified and directed.

S&F structural steel framed work as in doors frame or gates of angle or other section with gusset plates, rails, braces etc. Cutting, drilling and welding complete, drilled for fixing of steel sheeting or other covering. Doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed.

S&F 105x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed

S&F 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed

S&F 2nd class hard wood 35mm thickness of factory made plain framed, panelled shutter(two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated.

S&F for 2nd class hard wood 35 mm thick glazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I, sector 8, clause 8.20 (a) complete all as specified and directed.

S&F factory made 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on one sides and decorative face veneer with lipping/frame on front face to match complete all as specified and directed.

Supply and fixing 100mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

Material and labour for mild steel sliding door bolts 250mm long stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Supply and fixing MS pressed handles, oval type, stove enameled black 150mm size complete all as specified and directed.

Supply and fixing MS barrel tower bolt 200mm long, stove enameled black, with bright bolt and fixed complete all as specified and directed.

S&F PVC solid door frame of size 50mm x 47mm made out of 5 mm wood grain printed PVC sheet and edges will be painted to be matched with shutter, reinforced with MS square tube, as per specification and drawing in SSR Part-II complete all as specified and directed.

S& F Factory Made Solid PVC Moulded Door Shutters with particle board core, 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front Face & 2mm Prelam PVC sheet on back face all as per specification & drawing.

Supply and fixing 100mm butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

Supply and fixing 125mm size brass handles, cast type, polished bright complete all as specified and directed.

S&F 250mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed complete all as specified and directed.

Supply and fixing 200mm size brass barrel tower bolt, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excludding precast concrete articles all as specified.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6 M mean radius built in CM (1:6) all as specified.

Ditto as per description of item 58 above but except bricks (Note:- Servocable bricks retreived from Srl No 57 shall be used.

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) and removing surplus spoil out of Defence Land where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L for 100mm PCC 1:4:8 type D-2 using 40mm graded aggregate as in sub base flooring all as specified.

M&L for 50mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection/surface channels finishing the surfaces even and smooth without using extra cement all as specified.

M&L for 100mm thick PCC (1:2:4) type B1 using 20mm graded aggregate as in floor topping; concrete surface finished even & smooth without using extra cement complete all as specified.

S&F glass dividing strips, 38mm width 3mm thick and inserted in position to conforming to design.

M & L 30mm sand cushion, filling under floors or in foundations including watering and consolidation all as specified and directed.

M & L for laying 60 mm thick machine pressed precast concrete interlocking paver block and shape and size conforming to IS -15656-2006 of M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L PCC (1;2:4) type B-1 using 20mm graded stone agregete as in sides of rounded or chamfered on edges of interlocking tiles/benching complete all as specified and directed.

M&L for mild steel pipe 25 mm dia curtain road with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade as approved by GE all as specified.

S&F Framed work such as in gates, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

Demolition of reinforced cement concrete in ground floors and paving n. exc 15 cm thickness (reinforcement to cut as required to facilitate demolition) all as specified.

M&L for reinfored cement concrete type B-1 1:2:4 (20 mm graded aggregate) slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for MS TMT bars 10 mm and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for clos hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia.

M&L for form work to soffits of suspended slabs such roof slabs, floor slabs, shelves, landings and similar work, not exceeding 200mm thick (horizontal or slopping) rough finished surfaces of concrete flat or shelfs etc.

S&F brass chromium plated shower rose of 125mm size, with or without swivel joints including fixing to steel pipe or union in repair complete all as specified and directed.

S&F Corner Glass Shelf with bracket all as specified and directed.

S&F Vitreous china wash hand basin padestal pattern , white, flat back 550x400mm including one number brass CP waste coupling ,32mm dia , Pvc waste pipe with connector , brackets 2 nos including cutting for and pinning in ends of brackets complete all as specified

S&F Vitreous china wash hand basin , white or coloured, oval shape including one number brass CP waste coupling ,32mm dia, bottle trap, fixed on granite stone or counter type fixed ( including cut to granite stone properly) complete all as specified

S&F Hot and Cold mixer (swan neck) fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe for 15mm bore pipe fixed to wash hand basin complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20 mm dia , D type 60 cm long between CP flanges all as specified.

S&F vitreous china wash down water closet (Pedested patern ) white incl fixing bolt, plastic water closet seat cover white closed pattern, with & included arragement of jet sprey with flat bottom and cover and mild steel chromimum plated hinging device, fixed in repairs all as specified directed by Engr-in-Charge.

S&F vitreous china premium/1st quality wash down water closet wall hung EWC white/ivory/off white closed pattern inc all necessary accessories like rag bolts/gel gasket/ seat cover etc (excluding flushing cistern & flush pipe) complete all as specified directed.

S&F Soap Dish Holder all as specified and directed by Engr-in-Charge.

S&F Toilet Roll Holder all as specified and directed by Engr-in-Charge.

S&F Tooth Brush Holder/Tumbler Holder all as specified and directed.

S&F PVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle, 10 ltr capacity including brakets fixed in repairs

Supply and fixing 15mm stop valves fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

PVC connection fiber, reinforced 45cm long with brass check nut and PVC washers at both ends complete all as specified and directed.

S&F Fancy type CP Bib tap cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete fixed in repairs.

S&F Hot and cold mixer fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe suitable for 15mm bore pipe fixed to wall complete all as specified.

S&F medium grade steel water tubing, 15 mm bore galvanised with all fittings and fixed complete to walls or layed in floors including taking down of existing tubing and connections all as specified and directed.

S&F medium grade steel water tubing, 20 mm bore galvanised with all fittings and fixed complete to walls or layed in floors including taking down of existing tubing and connections all as specified and directed.

M&L refixing old tubing 15mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor complete all as specified and directed.

M&L refixing old tubing 20mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor complete all as specified and directed.

S&F vitreous china urinal full stall type flat back complete incl providing and fixing plugs bedding urinal against wall in CM(1:2) securing urinal to plugs with and incl 60cm long bras scruees, pointing aroung urinal back in cement incl and fixing and flush pipe, grating with coupling and union for discharge complete all as specified.

S&F for stainless steel sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers including cantilever cast iron brackets, connecting union ,waste coupling and waste pipe over all size 915mm x 460mm with bowl size 410 mm x 330 x 160 mm.

Demolition and braking up drain pipes AC/PVC pipe in event n.exc 150 mm dia including all fittings.

S&F for 110 mm PVC (SWR) single socketed in any length with rubber ring joints fixed to floor complete all as specified.

ditto as per item 98 above but 75 mm dia

PVC (SWR) bends 110 mm with access door

Ditto as per item 100 above but 75 mm with access door

S&F for 110mm PVC (SWR) vent cowl

M&L for providing precast cement concrete 1:2:4 type B0 (12.5 mm graded aggregate) louvres and jallies, 25mm thick (measured solid), including all moulding but excluding frame (Precast frame shall be measured separately) set in cement mortar 1:4 complete all as specified. (Note:- Unit rate quoted shall be deemed to include cost of reinforcement and form work)

Providing precast cement concrete 1:2:4 type B-1(20 mm graded aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry) string coarses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbles, brackets etc (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc and setting in mortar complete with joints to match set in cm 1:4 complete all as specified. (Note:- (i) Unit rates quoted shall be deemed to include cost of form work. (ii) Reinforcement , if any , shall be measured and paid under respective item of BOQ)

S&F 1000 ltr rotational moulded polythylene water storage tank (Cylindrical vertical with closed top) hosted and fixed in position incl dismantling of existing tank of any description complete all as specified.

S&F in repairs 20mm for ball valve brass high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed

Taking down carefully existing point wiring of any type/ any size (ie on wooden/ batten, surface conduit, casing capping or concealed conduit) complete for light, fan, socket or power point etc including removing switches, sockets, holders, ceiling rose, pendants, regulators, light fittings, switch board outlets with sheets and other materials from site for refixing of serviceable light and for taking credit of unserviceable light as per Sch of credit and making good disturbed surface of walls,roof, floors etc. with any type of civil wk involved complete all as specified and directed.

M&L for point wiring for light/fan point with 1.5 Sqmm (nominal area) FRLS PVC insulated unsheathed multistranded copper conductor of size 1.5 Sqmm cable drawn in and including concealed rigid PVC conduit medium grade not less than 20mm dia with accessories including cutting chases for laying of conduit, fixing of boxes in walls/floor etc including making good to disturbed surfaces as per adjoining specification and terminated in and incl steel sunken boxes suitable for modular fitting, incl suitable modular cover plate reqd & accessories including FRLS PVC insulated unsheathed multistranded copper conductor 1.5 Sqmm single core as earth continuity conductor (green colour) connected with earth dolly with thimble complete all as specified and as directed by Engr-in-Charge.

(a) All as per srl item No. 108 here in before but for one socket outlet 5 Amps on independent board complete all as specified.

(b) All as per srl item No. 108 here in before but for one socket outlet 5 Amps on the same board controlled complete all as specified.

(c) All as per srl item No. 108 here in before but for one bell point controlled by one bell push complete all as specified.

All as per srl item No. 108 here in before but with 2.5 Sqmm (nominal area) FRLS copper cable for one 3 Pin 15 Amp socket on independent board including one 2.5 Sqmm copper conductor multi stranded green colour PVC insulated unsheathed FRLS cable 1100 volts grade as earth wire connected to common earth and earth dolly with all accessories complete all as specified and directed by Engineer-in-Charge.

S&F Modular switch, 6 Amps, 240 Volt AC single pole, one way complete all as specified.

S&F Modular switch , 16 Amps, 240 Volt AC single pole, one way complete all as specified.

S&F Modular socket out let 6 Amp, 5 pin, 2-in-1 complete all as specified.

S&F Modular socket outlet multi purpose 2 in 1, 5/6 pin, 6 & 16 Amps, complete all as specified.

S&F in replacement Modular bell push switch 5 Amps, SP, 240 volts, 1 module complete all as specified and directed.

M&L for door bell electric AC (Ding Dong) 240 volt SP complete all as specified.

S&F ceiling rose surface type PVC/ polycarbonate 65mm x 50mm three terminal complete all as specified.

S&F 2 Module five step fan regulator, electronic type, single phase, including connection complete all as specified.

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with matching colour back plate all as specified and directed.

M&L for sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 4 Sqmm drawn through in and including PVC rigid non metallic concealed conduit (medium grade) with all fittings including earth continuity FRLS PVC insulated unsheathed multistranded copper conductor cable 4.0 Sqmm PVC insulated with green insulation complete all as specified. NOTE: Two run of 4 sqmm wire and one run of 4 sqmm wire as earth wire including PVC conduit shall be measured as one unit.

M&L for sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 6 Sqmm drawn through in and including PVC rigid non metallic concealed conduit (medium grade) with all fittings including earth continuity FRLS PVC insulated unsheathed multistranded copper conductor cable 6 Sqmm insulated with green insulation complete all as specified. NOTE:Two run of 6 sqmm wire and one run of 6 sqmm wire as earth wire including PVC conduit shall be measured as one unit.

Supply and fixing by passing through conduit FRLS PVC insulated unsheathed multi stranded copper conductor of size 1.5 Sqmm single for inverter wiring complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket (for Geysers) complete with one single pole MCB of 16 amp 240 V 10 KA complete all as specified and as directed.

S&F MCB protected socket complete wit metal sunken box (with sheet steel enclosure) incl 16 Amp MCB SP confirming to cat part No DHDMCSN0251016 of Havells or equivalent in specified makes complete all as specified and as directed.

Supply & fixing LED retrofit lamp 9W , 6500K, 220-240V with base cap B-22. complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20 Watt, 220V,AC, batten type with integrated LED and driver incl provn & connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F in repair Decorative wall mounting light fitting suitable for 09 watt LED lamp complete with opal glass diffuser including 1 x 09 watt retrofit CFL lamp complete confirming to cat part No LHFOAJE1TN1I060, model Floretline WL 1LS or equivaent in specified makes as approved complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed

S & F energy saving & environmental friendly long life versatile pressure die-cast aluminium housing luminaire with heat resistant glass and suitable optics for uniform distribution of light 25 watt (min) LED for bldg security lights with high efficiency electronic driver BIS approved, having IP-66 protection, surge protection operative on AC supply 140 volts to 270 volts pre-wired complete with GI pipe of 25mm bore and MS clamp duly painted with two coat paint all as specified and directed.

Fixing only serviceable tube light fittings any type and any description retrieved under item Srl No. 107, including necessary electric connection with round flexible wire with multi stranded copper conductor of size 0.50 sqmm, 3 core, 1100 volts grade complete all as directed.

M&L in replacement for sheet metal DB for MCBs, SPN, 12 ways 240 v, double door, single phase, with copper bus bar, neutral bar/ connectors suitable copper thimbles, lugs etc incl any type of civil work involved complete all as specified.

M&L in replacement for sheet metal DB for MCBs, SPN, 8 ways 240 v, double door, single phase, with 200 Amps rated bus bar, neutral bar/ connectors suitable copper thimbles, lugs etc incl any type of civil work involved complete all as specified.

M&L in replacement for sheet metal DB for MCBs, SPN, 6 ways 240 v, double door, single phase, with 200 Amps rated bus bar, neutral bar/ connectors suitable copper thimbles, lugs etc incl any type of civil work involved complete all as specified.

Supply and fixing in repair VTPN DB 8 way double door, suitable for MCCB 100 Amp, having copper bus bar for neutral and earth, blanking strips incl any type of civil work involved complete all as specified and directed.

Supply and fixing in repair TPN vertical DB 6 way double door, suitable for 63 Amp TPN, having copper bus bar for neutral and earth, blanking strips incl any type of civil work involved complete all as specified and directed.

Supply and fixing in repair TPN vertical DB 4 way double door, suitable for 63 Amp TPN, having copper bus bar for neutral and earth, blanking strips incl any type of civil work involved complete all as specified and directed.

Supply & Fix MCB SP 6 to 32 Amps 240 V, 10 KA, B curve complete all as specified and directed by Engr-in-charge.

Supply & Fix MCB SPN 40 Amps 240 V, 10 KA, B curve complete all as specified and directed by Engr-in-charge.

Supply & Fix MCB SPN 63 Amps 240 V, 10 KA, B curve complete all as specified and directed by Engr-in-charge.

Supply and fixing in repair MCCBs 100 Amp 4 pole 415 V, fixing type with breaking capacity 16 KA complete all as specified and directed.

Supply & Fix MCB SP 63 Amps 240 V, 10 KA, B curve complete all as specified and directed by Engr-in-charge.

Supply and fixing TPN 63 Amp, 415V 10KA 'B' curve miniature circuit breaker (MCB) in the DB complete with connection testing complete all as specified and directed.

Supply and fix electric water heater, storage type with inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all standard accessories incl such as safety valve, thermostate, NRV, connection piece etc.

Supply & fixing exhaust fan, 450 mm sweep, 900 rpm, single phase, 230 volt, heavy duty, with louver shutter (superior quality) including provision of three core flexible cable of required length of size 23/.0076 from ceiling rose/ connector to fan terminal, fixing the fan on wall with suitable size of nut, bolt & washer complete fixing with rag/ anchor bolts.

Supply & fixing exhaust fan, 300 mm sweep, 900 rpm, single phase, 230 volt, heavy duty, with louver shutter (superior quality) including provision of three core flexible cable of required length of size 23/.0076 from ceiling rose/ connector to fan terminal, fixing the fan on wall with suitable size of nut, bolt & washer complete fixing with rag/ anchor bolts.

Supply & fixing PVC exhaust fan, 250 mm sweep, single phase, 230 volt, heavy duty, with lovered shutter including provision of three core flexible cable of required length of size 23/.0076 from ceiling rose/ connector to fan terminal, fixing the fan on wall with suitable size of nut, bolt & washer complete fixing with rag/ anchor bolts.

Cutting holes for exhaust fan of size 450mm dia sweep in brick walls built in cement mortar or cement lime mortar and stone walls built inline mortar for inserting holdfasts and making good dismantled portion in cement mortar 1.3 or cement concrete 1:2:4 Type B-1 as required.

Cutting holes for exhaust fan of size 300mm dia sweep in brick walls built in cement mortar or cement lime mortar and stone walls built inline mortar for inserting holdfasts and making good dismantled portion in cement mortar 1.3 or cement concrete 1:2:4 Type B-1 as required.

Cutting holes for exhaust fan of size 250mm dia sweep in brick walls built in cement mortar or cement lime mortar and stone walls built inline mortar for inserting holdfasts and making good dismantled portion in cement mortar 1.3 or cement concrete 1:2:4 Type B-1 as required.

S&F BLDC ceiling fans complete with electronic type regulator and accessories 230 V, 1200 mm sweep, BEE 5 star rated.

Supply & fix wall mounting fan 230 volts single phase 400 mm sweep min or next higher cap available, 3 speed, suitable for wall mounting type complete all specified and directed.

S&F 1 Module blank (dummy) plate suitable for Modular switch cover plate complete all as specified.

M&L for sub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 2.5 Sqmm drawn through in and including PVC rigid non metallic concealed conduit (medium grade) with all fittings including earth continuity single wire FRLS PVC insulated unsheathed multistranded copper conductor cable 2.5 Sqmm (green insulation) with any type of civil work including making good to disturbed surfaces to match existing surface complete all as specified. NOTE: (i) Two run of 2.5 sqmm wire and one run of 2.5 sqmm wire as earth wire including PVC conduit shall be measured as one unit. (ii) Excavation and earth work shall be deemed to included in unit rates quoted.

Earthing complete in replacement with galvanised steel earth plate electrode 60cmx60cmx6.0mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level with the top edge of electrode not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and incl GI lead protection pipe of GI light grade 15mm dia upto 7.5 mtrs and watering pipe 20mm bore of GI medium grade with funnel and wiremesh, earth plate covered on all sides with min 150mm thick alternate layers of charcoal, salt all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing point with PCC chamber and RCC cover in 1:2:4 complete with any type of earth work involved.all as specified and directed and testing on completion. Note:- PCC Chamber shall be constructed at least 0.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner.

M&L for LED bollard light 18/20 watt min complete incl suitable PCC foundation all as specified and directed.

Supply, installation, testing and commissioning XLPE insulated, PVC sheathed galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 240 sqmm 3.5 core complete laid in trenches passing through pipes, road, floor, in trenches/culverts all as specified and directed by Engineer-in-charge. Note:- Excavation and earth work, sand cushioning and cable cover shall be measured and paid under respective items of BOQ.

Supply, installation, testing and commissioning XLPE insulated, PVC sheathed galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete laid in trenches passing through pipes, road, floor, in trenches/culverts all as specified and directed by Engineer-in-charge. Note:- Excavation and earth work, sand cushioning and cable cover shall be measured and paid under respective items of BOQ.

Supply, installation, testing and commissioning XLPE insulated, PVC sheathed galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 sqmm 4 core complete laid in trenches passing through pipes, road, floor, in trenches/culverts incl taking out old UNSV cables all as specified and directed by Engineer-in-charge. Note:- Excavation and earth work, sand cushioning and cable cover shall be measured and paid under respective items of BOQ.

Excavation in trenches in soft/Loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and getting out complete all as specified and directed by Engineer-in -Charge.

Returning and filling in, including spreading and levelling, water and well remming in layers not exc. 25cm all as specified and directed.

Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed.

Supply and laying old size sub class 'B' bricks laid flat in trenchs over the cable with the length of brick perpendicular to the direction of cable length, compressive strength of brick shall not be less than 160 kg/cm² adjacent/abutting each other complete all as specified and directed by Engineer-in-Charge.

Material and labour Sand cushioning with 8cm thick layer of sand before laying of cable and 15cm thick after laying of cable in trenches complete all as specified and as directed.NOTE : Punned thickness of 18 cm will be considered for payment.

M&L for GI tube light grade 100mm bore laid in trenches or fixed on wall/floor for protection of UG cable complete all as specified and directed.

M&L for GI tube light grade 50mm bore laid in trenches or fixed on wall/floor for protection of UG cable complete all as specified and directed.

M&L for GI tube light grade 40mm bore laid in trenches or fixed on wall/floor for protection of UG cable complete all as specified and directed.

Material and labour for boring hole under the road/pavement/hard standing with the help of trenchless technology using ultra sound technique and necessary machine for inserting GI pipe 100mm/ 50mm with suitable working pressure not less than one meter below ground level complete all as specified and directed by Engineer-in-charge.

Supply, install, testing and commissioning LT panel (1500mm x 1200mm x 550mm min ), Outdoor type cubicle type, Floor mounted weather and vermin proof totally enclosed made out of 3.15 mm thick CRCA sheet machine pressed of suitable size having IP-54 protection, suitable to operate on 3 phase 4 wire system , 415volts, 50 Hz with front and rear openable and locking arrangement, double door type, bottom gland plate with sufficient numbers of circular cable entry holes, danger notice plates, sliding bolts (on both sides), complete duly powder coated with 7 tank process mounted on angle iron stand height 80cm made out of angle size 50 x 50 x 6 mm comprising with following complete all as specified:-

(i) Bus bar strip,four pole and capacity 600 Amps copper,Based on 1.5 Amps per sqmm, coloured with plastic coated insulated and sleaves in four colours (Red,Yellow, blue and black ) fixed on porcelain insulators with necessary nuts and bolts and washers etc (ii) The panel door's each leaf shall have minimum three hinges.

INCOMING : -

(a) MCCB 400 Amp, 415 V, 36 KA, 4 pole adjustable thermal magnetic release type -01 No.

(b) Indicator with LED lamps for RYB , 3 Phase - 01 set

(c) Digital mulit function metre able to display parametres KWH, VOLTAGE( Phase to neutral and phase to phase), AMPERE, FREQUENCY,POWER FACTOR.

OUTGOING : -

(a) MCCB 40 Amp, 415 V, 16 KA, 4 pole fixed thermal & magnetic type - 01 Nos (Spare)

(b) MCCB 63 Amp, 415 V, 16 KA, 4 pole fixed thermal & magnetic type - 03 Nos.

(c) MCCB 100 Amp, 415 V, 16 KA, 4 pole fixed thermal & magnetic type - 03 Nos. Each 100 Amp MCCB should be provided with suitable CTs - Set of 3 and 01 No Digital Energy Panel Kwh meter of class 0.5 min

(d) MCB TPN 32 Amp - 01 Nos

Earthing complete in replacement with galvanised steel earth plate electrode 60cmx60cmx6.0mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level with the top edge of electrode not less than 1.5 metres below normal ground level connected to galvanised earth strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron and incl GI strip protection pipe of GI light grade 40mm dia upto 7.5 mtrs and watering pipe 20mm bore of GI light grade with funnel and wiremesh, earth plate covered on all sides with min 150mm thick alternate layers of charcoal, salt all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing point with PCC chamber and RCC cover in 1:2:4 complete with any type of earth work involved.all as specified and directed and testing on completion. Note:- (i) PCC Chamber shall be constructed at least 0.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner. (ii) Excavation and earth work shall be deemed to be included in unit rates quoted.

M/S Kuldip Construction Co. (BID ID -3088438)

SANDEEP JHANJI CONSTRUCTIONS (BID ID -3093784)

CHOUDHARY AND SONS (BID ID -3095345)