SPECIAL REPAIRS TO OR MD ACCN BLDG NO P-47 AND PROVN OF 30 KVA UPS AT OPERATION THEATRE EXHAUST FAN IN KITCHEN AND BATHROOMs OF JCOs OR MD ACCN AND WARDs/DEPTs AT MH UNDER GE (EAST) MATHURA

Amount

Demolition of cement concrete (reinforced) as roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to faciliate demolition) complete all as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 15 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

M&L for Cutting chases pinning in brick walls making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled conduit wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 20 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 25 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

M&L for pre cast reinforced cement concrete type B-1 1:2:4 (using 20 mm graded stone aggregate) as in cover slab (for manholes etc) chajja, shelves and similar articles complete all as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L for Brick work with fly ash Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Demolition of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc (each layer) laid bedded and pointed in any mortar complete all as specified and as directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed.

M&L for 50 mm( average) thickness cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregates) as in floors/padding finishing cement concrete surface even and fair without using extra cement compete all as specified and as directed.

M&L for bitumen felt water proofing treatment using APP based polymeric membrane minimum weighting 3kg/sqm and minimum thickness 3mm reinforced with polyster non wove fabric (but not less than 150gms/sqm) laid over bitumen primer applied @ 0.30 Kg/sqm by torch application complete all as specified and as directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for cement concrete tiles 25cm x 25cm x 22mm thick, with grey cement and no pigments, machine pressed, set in neat cement slurry in floor over and including 15 mm thick screed bed in cement mortar 1:4 and filling the joints with Tile Max premium cementitious grout material of JK Cement or its equivalent complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface of size 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick rendering in cement motar 1:4 complete all as specified and as directed.

Demolition of stone slabs of any description or thickness in floors/apron etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for machine cut kota stone slab as in flooring 20-25 mm thick laid over and including 15mm thick screed bed in cement mortar 1:6 and jointed with gray cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps jambs, pillar, window cills, cooking platform and like laid over and including 10mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2) using marbal dust with admixture of pigment to match the shade of granite complete all as specified and as directed.

Taking down cement plaster on brick walls and concrete surface including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick wall or concrete surface in cement mortar 1:4 mixed with liquid water proofing compound @200ml/50 kg bag of cement surface finished complete all as specified and as directed. Note : Liquid WPC shall be measured and paid seperately under relevant item of this BOQ.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 finished even & smooth (without using extra cement) complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:3 finished even & smooth (without using extra cement) complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying one coat of alkali resistant primer paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of exterior emulsion apex paint complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls applying two coat of oil bound distemper over and including a coat of alklai resitant primer complete all as specified and as directed.

M&L for providing 1mm thick wall care putty on plastered surfaces of walls complete all as specified and as directed.

M&L for prepration of new plastered surface of ceilling and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment of old surface of walls and applying two coat of oil bound distemper over and including a coat of wall care putty complete all as specified and as directed.

M&L for prepration of old plastered surface of walls and applying one coat of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment of old surface of walls and applying two coats of exterior emulsion apex paint complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm bore bends any radius complete all as specified and as directed.

S&F in repair PVC (SWR) 75mm bore bends any radius complete all as specified and as directed.

S&F in repair PVC (SWR) 75mm bore bends with access door any radius complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) junction single, (Single T) equal or unequal provided with acess door complete as specified and as directed.

S&F in repair 110 mm bore PVC (SWR), vent cowl complete as specified and as directed.

S&F in repair PVC (SWR) floor trap plain dia of outlet 75mm with CP grating including jointing with solvent cement complete all as specified and as directed.

S&F in repair long body bib taps cast copper alloy chromium plated fency type with crutch or butterfly handle, screwed down screwed for 15mm bore dia iron pipe complete all as specified and as directed.

S&F in repair angular stop valves/Anguler cock type cast copper alloy chromium plated with crutch or butterfly handle, screwed both ends for 15mm bore dia iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete including jointing to socket of flushing pipe complete all as specified and as directed.

S&F in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets for bottom support fixing with gutties embeded in wall with driling machine etc complete all as specified and directed.

S&F in repairs Stainless steel sink with draining board made out of 1.0 mm thick sheet for kitchen with plug washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe. Overall size 915mmx460mm bowl and size 410x330x160mm complete as specified and as directed.

S&F in repair vitreous chinaware wash hand basin white flat back size 550x400mm including brackets, 32mm waste coupling and pillar tap brass cast copper alloy chromium plated, fancy type with capstan heads,screwed down high pressure,with or without letters Hot or Cold with long screwed shank and fly -nuts, screwed for iron pipe 15 mm bore dia complete all as specified and as directed.

S&F in repair swivel shower of PTMT any colour for fixing with 15mm pipe (minimum weight 40gms) complete all as specified and as directed.

S&F in repair shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and as directed.

Supply and fix in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm bore dia complete all as specified and as directed.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes 20 mm bore dia complete all as specified and as directed.

S&F in repair PVC connection 15mm size with PTMT nut of length 600mm complete as specified and as directed.

S&F in repair 32mm bore high density Polyethylene Pipe (HDPE) of pressure rating 6 kgf/cm2 and fittings fixed to WHB, sink complete all as specified and as directed.

S&F in repair stainless steel kitchen plate rack of size 31" x 30" x 10" deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and as directed. Make : Prayag cat No P-346 or equivalent of make specified in Appx 'B'

S&F in repair stainless steel towel rail 600 mm long, 20mm dia fixed with steel screw complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consiting of 5.5 mm sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repairs corner racks with glass of size 300x300mmx8mm thick, bevelled on edges with two brackets CP complete all as directed.

M&L for 50 mm thick sand stone slabs as in chajjas of ground and first floors over windows, doors etc set and jointed in cement mortar 1:4 complete all as specified and directed.

M&L for 25mm( average) thickness cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregates) as in floors/padding finishing cement concrete surface even and smooth (without using extra cement) compete all as specified and as directed.

S&F rolled mild steel joist, channel, angle or Tee section fixed independently without connecting plate etc cut to ordinary length i.e. within 20 mm of length indicated) of Fe 410 Gde E-250 quality including applying two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed.

S&F in repair 20 mm dia fency type mild steel drapery rod cut to size and fixed in position including end caps, roller and brackets fixed to wall complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (Below or above ground level) including removal of debris outside of MOD land complete all as specified and as directed.

M&L 100mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 grade of concrete as in floors/pavements complete all as specified and as directed.

M&L for 50 mm thick cement concret type C-1 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement compete all as specified and as directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, machine pressed, set in neat cement slurry in floor over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but n exc 4 Sqm each complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawingd complete all as specified and as directed.

S&F to the frame at site, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be coverd with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail of either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed in the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

S&F Pressed steel frames of size 105x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete as specified and as directed.

M&L for Pressed steel frames of size125x60mm (using 1.60mm thick MS sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. supplied and fixed complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in bed blocks for fixing hold fasts and filling of chowkhats etc complete all as specified and as directed.

M&L for prepration of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over primed surface complete all as specified and as directed.

S&F 35 mm thick factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as spicified and as directed.

S&F 35 mm thick factory made flush shutters, solid core construction with block board core and plywood face panel veneer type on both side complete all as specified and as directed.

S&F 150mm long aluminium anodised handles fabricated type complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts 200 mm length of bolt of extruded section and fixed complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250 mm long of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F stainless steel Butt hinges 100mm of extruded section and fixed complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of red oxide primer complete as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of pink primer complete as specified and as directed.

S&F MS Framed work such as grills gratings, door and cooler stand, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for door windows, ventilators (sliding, fixed or casement) with one or more rebates including joining cleat for fixing etc,complete all as specified and as directed.

M&L Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F 5mm thick, Sheet glass ordinary quality and glazing with rubber beading in square n.exc. 0.5 sqm in each pane and fixed to aluminium/steel/wooden frame complete all as specified and as directed..

S&F aluminium anodized barrel tower bolts 75mm length of bolt of extruded section and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium anodised body and tengue, anodised with hard drwan steel spring overall length of cover plate 150 mm complete all as specfied and as directed.

S&F 300 mm, mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, coping, benching rounded or chamfered on edges complete all as specified and as directed.

M&L for 10mm thick polymer modified plaster in cement mortar 1:3 mixing the polymer in the ratio of 1:10 (1 part of polymer & 10 parts of cement) for sides and base of sunken floor portion complete all as specified and as directed. Note : Make of polymer Asian paints/Pidilite/STP/ Thermax/Sico

M&L for cement concrete 1:7:12 type F2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

S&F in repair 18/19 mm thick block board grade Ist quality, exterior grade commercial type fixed with screw to timber frame work complete all as specified and as directed.

S&F 100mm size aluminium anodised Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F Continuous (piano) hinges width of flaps 40 mm (when opened) mild steel, bright finish or electrogalvanised complete all as specified and directed.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as specified and as directed.

Taking down old unserviceable existing SPN/TPN DB/enclousers any size and type/any descriptions as iron sheet scrap including MCB's/MCCB's any type/size and making good disturbed surface/wall as per existing complete all as specified and directed.

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated (FRLS) cable 1100 volts grade with multi-stranded, copper conductor drawn through and including 20mm dia rigid non-metallic PVC conduit with all acessories such as internal bend end caps etc complete concealed in wall including necessary cutting chases and making good disturbed sufrace to match the existing surface including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistrandered copper conductor cable as earth continuity conductor, fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls with 3mm thick bakelite top cover sheet ISI marked with chrominium plated screws and cup washers for housing the switches, socket outlets fan regulators etc complete all as specified and as directed the followngs:-

One light/fan/exhaust fan point controlled by one way switch 5 amp complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on same board complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on independent board complete all as specified and as directed.

One bell point controlled by one push button on independent board complete all as specified and as directed.

One light point controlled by 2 way switch 5 amp complete all as specified and as directed.

All as per item No. 107.00 here-in-above but for 3 pin /5 pin 15Amps socket point controlled independently, with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified and as directed.

Supply and Fixing Modular bell push 6 Amps with indicator single pole one way, 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch 16 Amps single pole one-way, 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps single pole two-way, 1 Module complete all as specified and as directed.

Supply & Fixing fan Regulator electronic step type 100 watt, 2 Module complete all as specified and as directed.

Supply and Fixing socket outlet 2-in-1, 3pins 6 Amps , combined 2 Module complete all as specified and as directed.

Supply and Fixing socket outlet 2-in-1, 3pins 6/16 Amps, combined 2 Module complete all as specified and as directed.

S&F ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and as directed.

S&F Bell Ding dong type, AC, single pole, 240 Volts complete with electric connection complete all as specified and as directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F indoor decorative ultra slim surface/Wall mounted LED batten tube light fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired with and including 1 x 20 watt LED tube and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED 9 Watt suitable for B22 type holder, natural white complete all as specified and as directed.

Taking down electric meter from location, safely keeping a side and refixing the same with nut, bolts, suitable thimbles including making connection complete all as specified and as directed.

S&F SP enclosure modular type with a two pin and earth plug and socket complete with SP MCB of rating 16 Amps, 240 Volts with all connection complete all as specifed and as directed.

S&F LED bulk head with PDC aluminium housing and milky diffuser capacity 10 watt complete with all accessories and connection complete all as specified and as directed.

S&F 35W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including 30 LED light and all connections complete all as specified and as directed.

S&F in repair building security light bracket made out of 40mm dia light grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/wall including two Nos of clamps made out of 50x40mm flat fixed with nuts and bolts including applying two coats of aluminium paint over a coating of red oxide primer complete all as directed.

Supply & fixing CRCA sheet powder coated MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, triple pole and neutral 4 way 415 V with 200 Amps rated copper bus bar, type complete all as specified and as directed.

S&F MCB TPN 100 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F sheet metal enclosure MCB distribution board, SPN 12 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified and as directed.

S&F MCB SPN 40-63 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SP 6-32 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

M&L for Sub Main Wiring with two runs single core 6sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) with and including 6sqmm copper green colour earth wire complete all as specified and as directed. Note : Two runs 6sqmm, one run of 6sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

Taking out the electric geyser of capacity 25 Ltrs carefully from its installed position by disconnecting inlet and outlet water pipes, dismantling the unit and replacing the defectiv parts and painting with one coat of synthetic enanel paint and writing MES No and safely keeping a side & refixing in its original position after completion of civil works and reconnecting the inlet/outlet water pipes and testing on completion complete all as specified and as directed. Note : The spare parts required shall be measured and paid separetely under relevant items of this BOQ.

Supply only following items to be incorporated against item No 132.00 here in before complete all as specified and as directed.

Heating element 1.5/2 KW ISI marked including rubber Gasket as per existing type complete all as specified and as directed.

Thermostat suitable for 25 Liter Geyser as per the existing type complete all as specified and as directed.

Hot water/cold water pipe 600mm long as per existing type complete all as specified and as directed.

Taking down the ceiling fan fan of any sweep carefully from its installed position, dismantling complete with down rod replacement of ball bearing capacitor, Rubber wheel bush and cleaning of all dust, applying grease for bearings, reassembling the fan and blades, painting of fans and down rod with synthetic enamel white paint by spraying including filling cavities with filler, writing MES No. with black paint, and keeping a side safely and hanging / refixing in position and connecting up including provision of 3 core twisted flexible copper conductor cable of 0.75 Sqmm from ceiling rose to connector of fan and testing on completion to entire satisfaction of Engineer-in-Charge complete all as directed.

Dismantling unserviceable ball bearing and supply and fix ball bearing suitable for ceiling fan/exhaust fan/fresh air fan complete all as specified and as directed.

Material & labour for removing the defective fan winding of ceiling fan size upto 1200mm/1400 mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, soldering, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and as directed.

Taking down the old exhaust fan of any sweep carefully from its installed position, dismantling complete and repair/replacement of unserviceable parts (like as bearing, capacitor, Rubber wheel bush) and cleaning of all dust, applying grease for bearings, reassembling the fan and blades, painting of fans and down rod with synthetic enamel white paint by spraying including filling cavities with filler, writing MES No. with black paint, and keeping a side safely and refixing in position and connecting up including provision of 3 core twisted flexible copper conductor cable of 0.75 Sqmm from ceiling rose to connector of fan and testing on completion to entire satisfaction of Engineer-in-Charge complete all as directed.

Material & labour for removing the defective fan winding of exhaust fan size upto 300mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, soldering, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and as directed.

Supply and fix in replacement MS louvers with nuts, bolts and washers suitable for exhaust fan upto 300 mm sweep of any description/make/model complete all as specified and as directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

Supply, installation, testing and commissioning of 30 KVA online three phase UPS with 100 AH, 12V SMF type batteries (30 Nos) for 60 minutes backup at full load. UPS system should be "True on-line double conversion UPS system" three phase input and three phase output with neutral, UPS should be DG set compatible, 50Hz, input voltage range 285VAC-485VAC and outut voltage stabilized at 415 with accuracy + 1%, inbuilt galvanic isolation transformer incorporated at the output side, including safety stop motions, self diagnostic features, alarms for safe, having multifunctional display showing all necessary parameters i.e main ON/OFF, inverter ON/OFF, malfunction indication, output voltage etc, mounted on castors, including MS battery stand having suitable racks for all bateries, including required wiring, links for interconnections of batteries complete all as specified and as directed.

M&L for Sub Main Wiring with four runs single core 10 sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) with and including 10 sqmm copper green colour earth wire complete all as specified and as directed. Note : Four runs 10 sqmm (P&N), one run of 10 sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

M&L for Sub Main Wiring with two runs single core 10 sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) with and including 10 sqmm copper green colour earth wire complete all as specified and as directed. Note : Two runs 10 sqmm (P&N), one run of 10 sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder coated with Copper bus-bar 200Amp, neutral link, earth bar and din rail ,blanking Plates, cable ties for cable management, 440 V, 4 way complete all as specified including fitting suitable for following MCCB/MCBs with connection complete all as specified and as directed. (i) MCCB 125 Amps, 4 Pole, 16 KA -01 Nos (ii) MCB SP 6-32 Amps - 10 Nos Note : - (i) MCB & MCB /MCCB DBs shall be of same make. DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as pe directed & rate shall be included in the items.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder coated with Copper bus-bar 200Amp, neutral link, earth bar and din rail ,blanking Plates, cable ties for cable management, 440 V, 4 way complete all as specified including fitting suitable for following MCCB/MCBs with connection complete all as specified and as directed. (i) MCCB 63 Amps, 4 Pole, 16 KA -01 Nos (ii) MCB SP 6-32 Amps - 10 Nos Note : - (i) MCB & MCB /MCCB DBs shall be of same make. DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as pe directed & rate shall be included in the items.

S&F TPN enclosure with a five pin (3P+N+E) and insulated earth plug and socket complete with TPN MCB of rating 32 Amps, 415 Volts, 10KA, Type 'C' with all connection complete all as specifed and as directed.

Supply & fixing CRCA sheet powder coated MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, triple pole and neutral 4 way 415 V with 100 Amps rated copper bus bar, type complete all as specified and as directed.

S&F sheet metal enclosure MCB distribution board, SPN 8 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified and as directed.

S&F MCB TPN 40-100 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SPN 32 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m in depth and n exc 1.5 m in wide for laying of cable etc. in soft/loose soil and getting out complete all as specified and as directed.

M&L for sand cushioning to under ground cable in trenches in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed. Note:- Measurement shall be taken after gentling puning of sand.

M&L for laying in trenches un-reinforced precast cement concrete cable cover, class LV type 1, flat, size 250mmx150mmx40mm for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

Returning filling in soil including spreading levelling watering and well ramming in layers not exc 25 mm thick complete all as specified and as directed.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor of size 16 Sqmm 4 core laid in trenches/duct/fixing on walls/poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole/Main Panel Box and testing complete all as specified and as directed. Note:- (i) Quoted rate shall deemed be inclusive of cost of HDPE pipe. (ii) Excavation and earth work shall be measured and paid separately under relevant item(s) of this schedule.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor of size 95 Sqmm 3.5 core laid in trenches/duct/fixing on walls/poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole/Main Panel Box and testing complete all as specified and as directed. Note:- (i) Quoted rate shall deemed be inclusive of cost of HDPE pipe. (ii) Excavation and earth work shall be measured and paid separately under relevant item(s) of this schedule.

Supply and fix exhaust fan, steel body AC single Phase, 50 Hz, RMP 900, 230V of size 300mm sweep with blades, and frame and louvers complete with flexible three core PVC sheathed and PVC insulated copper wire suitable length upto ceiling rose terminal complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase, 50 Hz, RMP 900, 230V of size 450mm sweep with blades, and frame and louvers complete with flexible three core PVC sheathed and PVC insulated copper wire suitable length upto ceiling rose terminal complete all as specified and as directed.

S&F exhaust fan 250mm sweep sturdy engineer plastic body complete with louvers, AC 230 Volt single phase 50 Hz supply and including connecting up with twin core PVC sheathed and PVC insulated copper conductor cable of suitable size 0.75 Sqmm length upto ceiling rose terminal complete all as specified and as directed.

M&L for Cutting holes/modified holes for air ducting of exhaust fan in Circule/square shape or as per site requirement including making good to the disturbed surface complete all as specified and as directed.

M&L for making hole in existing wall of suitable size 250/300/450 mm for fixing of exhaust fan and making good to the disturbed surfaces as per original including repair to disturbed surfaces with cement plaster work and apllying plaster of paris putty of 1mm thickness over the plastered surface complete all as specified and as directed.

ARCHI ENGINEERS (BID ID -3183398)

MAHTAB ALAM (BID ID -3183212)

KALPAARAV CONSTRUCTION (BID ID -3183472)