Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.2 CrAccepted-AOC NO 46 2 K D S ILLAM ARUNAGIRINATHAR STREET CHENNIMALAI POST ERODE DISTRICT 638 051 | ERODE | TAMIL NADU | 638051 | ₹24.2 Cr Quoted ₹25.2 Cr | L1 | Accepted-AOC ACCEPED |
| 2 | L2₹25.3 CrRejected-AOC NO 5 2 28B RAMAN NAGAR SALEM MAIN ROAD METTUR DAM SALEM DISTRICT 636 403 | SALEM | TAMIL NADU | 636403 | ₹25.3 Cr | L2 | Rejected-AOC REJECTED |
Tender Value
₹23.0 Cr
EMD Value
₹11.6 L
Closing Date
10 Apr 2024, 3:00 pmClosed
JOINT COMMISSIONER
ARULMIGU KAPALEESHWARAR TEMPLE MYLAPORE CHENNAI
Construction of New building for Arulmigu Kapaleeswarar Arts and Science college at Kolathur Chennai
2024_HRCE_448841_1
04/2023-2024
Open Tender
Civil Works - Buildings
540 days
KOLATHUR CHENNAI
Please refer Tender documents.
23 documents required · 23 mandatory
₹0
₹11.6 L
MYLAPORE CHENNAI
9 Oct 2024
14 Mar 2024
15 May 2024
14 Mar 2024
10 Apr 2024
14 Mar 2024
14 Mar 2024 - 10 Apr 2024
5 Apr 2024
Amount
Installation of vertical cast in situ bored piles using reinforced cement concrete Design Mix M30 Grade using 20 mm gauge hard broken stone jelly by settinng the bored cast in situ pile equipments with all accessories and tools at each locations based on the sequence of operations as directed by the departmental officer,boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified, by Direct Mud Circulation Method (using bentonite clay of required density) inclusive of pile accessories, temporary casing pipe,bentonite solution of 10% of concrete with required density, mobilisation, transferring, instalation of pile driving accessories from one location to other location another,pile concreting inside of drime method pipe fitting, including removal of mud and slurry away from the scheme site, including dismantling excess concrete but excluding the cost of steel and fabrication reinforcement grills but including Bentonite solution machinery charges labour charges etc., all complete, complying with relevent standard specification and as dircted by the departmental officers. (pile shall be measured from the top of the shoe to the bottom of the pile cap) Design Mix M30 Grade concrete should be prepared with ordinary Portland Cement with water cement ratio not exceeding 0.45 including the use of Plasticizer of required Grade and Hard Granite Stone Jelly of 20mm size and downgraded as per requirement.a) conducting routine pile test for one and half times the safe load for every 1 in 100 piles, as per IS code and as directed by the Departmental Officers (Cost not included) The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing should be as per clause 15.2.2. The length of pile for payment shall be measured up to natural ground level. The work should be carried out as per IS 2911. Pile depth should be decided by the departmental officer at site. Concrete for all piling work should be having minimum cement content of 400Kg per Cubic Metre.
450mm dia of pile
600mm dia of pile
Providing cast in situ bulb under reamed 300mm dia pile foundation and Cement concrete M25 using 20mm hard granite stone jelly.& below grade, including labour charges and hire charges for equipment s etc., with finishing neatly etc,. complete complying with standard specification and as directed by the departmental officers at site of work.
Initial Load Test as per IS 2911 Part IV 1985 including cost of single pile (250% of pile capacity), labour, reinforcement charges and all other incidential charges including excavation, shoring, strutting, dewatering, mobilization of equipments, etc. and also necessary hire charges for jacks, measuring devices, Structural Frame work for platform, Kent ledges etc, as required and providing pilecap.
450mm dia of pile 410 KN safe load
600mm dia of pile 910 KN safe load
Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including mobilization charges, labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.
450mm dia of pile 410 KN safe load
600mm dia of pile 910 KN safe load
Earthwork excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 meter and initial lift of 2 meter. and clearing and levelling the site, etc., complete complying with standard specification.
0 to 2m depth.
2 to 3m depth.
Supplying and filling in foundation, basement, etc with filling M sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.
Supplying and filling in foundation and basement with STONE DUST in layers of 150 mm thickness well watered rammed and consolidated complying with watered rammed and consolidated complying with relevant standard specifications including cost of filling sand as directed by the Departmental officers.
Supplying and filling in foundation and basement with Gravel Filling in layers of 150 mm thickness well watered rammed and consolidated complying with relevant standard specifications and as directed by the departmental officers.
Carting away the surplus earth excavated from the basement foundations / footings in the campus, is to be carted away to the desired lead of 20 kms from the site . The rate shall include loading into the tipper/ lorry, transporting and unloading etc., complete with all respects complying with relevant standard specification, as directed by the departmental officers. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the departmental officers.
Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.
Providing and laying Plain Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification
Providing and laying Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification
For Foundation and Basement
For Ground floor
For Fourth floor
Providing and laying position,Standardised concrete mix M-25 Grade in accordance with IS :456-2000,using 20mm and downgraded hard brocken granite stone jelly for all RCC items of works with minimum cement content of 3500 kg/cum and maximum water cement ratio of 0.55,inculding admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retart setting of concrete, improve workablity without imparing strengh and durability with about (5 cum)7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m)5156 kg of 10-12 mm machine crushed stone jelly and with about(4.79 cu.m)7670 kg of M-sand ,but eculding cost of reinforcement grill and fabricating charges,centering and shuttering and also inculding laying, vibrating with mechanical vibrtors,finishing,curing,etc,complete complying with standred specification and ass directed by the departmentel officers.the coarse and fine aggregates to be used shoul comply with the requirments of IS standreds.(No separate payment will be made by the Department for the excess usage of materials.)
For Foundation and Basement
For Ground floor
Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000,using 20mm and downgraded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
Foundation / Basement
Ground Floor
First Floor
Second Floor
Third Floor
Fourth Floor
Terrace Floor
Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire) as complete with all respects complying with relevant standard specification, as directed by the departmental officers. Grade of reinforced steel - Fe 550D - TMT bars
Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)
Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)
For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.
For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.
For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.
Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.30 m (height shall be the dimension as measured from the top of the lower slab / pcc sub base to the bottom of the subsequent upper slab) for every additional height of 1m or part thereof for plan area to be measured Suspended floors, flat slabs, drops, post tensioned slabs, slabs curved in plan to any radius, grid slab, roofs, landings, beams including spiral and curved beams of all radius, post tensioned beams, grid beams, plinth beams, girders, bressumers, cantilevers and balconies etc. and as complete with all respects complying with relevant standard specification, as directed by the departmental officers.
Providing and constructing of Brick work in following Cement Mortar using best quality Fly ash bricks of size 230x110x75mm in Cement Mortar 1:5 for foundation and basement including curing etc.,complete complying with standard specification.
Foundation and Plinth / Basement Level
For Ground floor
Providing and constructing of Brick work in following Cement Mortar using best quality Fly ash bricks of size 230x110x75mm in Cement Mortar 1:6 for super structure including curing etc.,complete complying with standard specification.
Ground Floor
First Floor
Second floor
Third Floor
Fourth Floor
Terrace Floor
Brick partition walls of 11.50cm thickness using best quality Fly Ash Bricks of size 230 x 110 x 75 mm in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)
Ground Floor
First Floor
Second floor
Third Floor
Fourth Floor
CRCA Pressed Steel Box Section 18 Gauge or 1.25mm thick for Door Frames including providing holes and fixing wooden blocks for fixing furniture and fittings With powder coated primer.
Supplying and fixing of soild core Flush shutters with Teak ply on both sides with teak wood lipping all-round 35 mm thick including cost and labour for fixing the Aluminium furniture fittings viz. 2 no. of Door Handle 3 nos. of 5" Aluminium Butt hinges, 2 nos. of 6"x1/2" Tower bolt,1no. of 10"x5/8" Aldrop, 1no. of Rubber bush,1no. of door stopper with rubber bush, with required screws etc. and Polishing the teak wood door with two coats of best French (Lac) polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., c (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.) all complete complying with relevant standard specifications and as directed by the departmental officers.
Supplying and fixing wood polymer composite board solid door frame and 25mm thick shutter frame corners of extruded outer size 75mm X 50mm the inner core more rigid WPC composite with minimum shore hardness of 55 and bulk density 0.8 Grams per cubic centimeters. The frame shall be fixed to the wall using 10 X 100 mm long MS screw through the frame through the pvc fastener. Minimum three numbers of screw to be provided for each vertical member. The overall size of frame shall be with suitable rebate for housing shutter and shutter consist of 25mm polymer composite board single core exhaust with one side embo printing design. To avoid duplicate from the printing design shall have logo of the WPC board shall be bount aid proved by kept official. The shutter shall be provided with 3 Nos of 4” SS butt hinges, 2 Nos of 4” Stainless Steel handles, 3 Nos of 6” Stainless Steel tower bolts with required Stainless Steel screws including labour charges for fixing the shutter frame, shutter and furniture fittings in position and finished smooth with template etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officers
Supply and fixing Fire rated door hollow metal doors - Powder Coated with vision panel of size 200 x 300mm. Frame: a) Material - 1.60 mm max (16 gauge) galvanized steel sheets complying to IS 277 Code of GPL Grade with Z 120 Coating. b) Profile - Double Rebated Frame to be of dimensions 150 mm X 58 mm and Single Rebated Frame to be of dimensions 100mm x 58 mm. c) Manufacture - 1.60 / 1.2 mm thick galvanized steel sheet to the specified profiles and dimensions. Frames manufactured at factory shall be knock down form with mitered assembly at site. d) Door frame preparations – to be provided with back plates on all jambs with provision for anchor bolt fixing to wall openings. All frames to have reinforcement pads for fixing of door closer, at appropriate location as per manufacturer’s details. e) Frames to have factory finish-pre-punched cut outs to receive specific hardware and ironmongery. f) Frames to be provided with hinge plates 3 mm thick pre-drilled to receive hinges for screw mounted fixing. All cut outs including hinge plates, strike plates to have mortar guard covers from inside to prevent cement, dust ingress into cut outs at the time of grouting. g) Frames to have rubber shutter silencer on strike jambs for single shutter frames and on the head jambs for double shutter frames. h) Frames shall be finished with Pure Polyester Powder Coated to any RAL Shade to withstand 300 hours of salt spray.
2hrs. Fire rated hollow metal doors - Powder Coated Double leaf door of size 1500x2100mm with vision panel of size 200 x 300mm. Hardware : SS Ball bearing hinges - 4"X3"X3mm, with Panic Bar for Double Door, External trim with Half Cylinderand TS 92 door closer
UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.
UPVC Ventilator : Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work
Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate isinclusive of the charges for cutting, bending, welding,grinding, polishing, conveyance, electrical charges, etc. complete
Wall Handrail Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete
Supplying and Fixing MS Ladder width 45cm using 50x50x6mm MS Angle cost of applying priming coat of paint as directed by the Engineer at all heights and levels etc., complete with all respects complying with relevant standard specification and as directed by the departmental officers.
Supplying and fixing of mild steel grills to windows and ventilators including cost of necessary screws and cost of applying priming coat of paint etc, as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall include for necessary tools & plants, welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the departmental officers.
Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
Flooring with following Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
Supply and Laying flooring with best quality of Granite slab leather finish 18 to 20mm thick (Steel Grey, Sira Grey, Ruby Red, SK Blue, Raw silk, Antique Brown) of size not less than 1200 x 600 mm machine cut with approved pattern in a single colour/multiple colour and set in C.M 1:4 (1 of cement : 4 of sand) 20 mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern, including finishing the joints with matching shade, cement slurry, cutting, edge chamfering and polishing rough, medium, nice and tin-oxide polish. Rate shall include wastages, preparation of base surface, cleaning, acid wash over the finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over, work at all levels and as complete with all respects complying with relevant standard specification and as directed by the departmental officers.
Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.
Providing flooring with best quality approved make White ceramic tiles ranges, Size of tiles shall be 6mm thick of 300 x 300 mm size set in CM 1:4, (1 of cement : 4 of M.Sand), 20mm thick and pointing the joints with Laticrete and pointing with Laticrete of approved make and as directed. Rate shall include for preparation of base surface, and finishing the surface, cleaning the surface, and protecting and with Gypsum / POP layer over Plastic sheet and removing the same before handing over, work at all levels etc. as complete in all respects and complying with relevant standard specifications and as directed .( Over Head Tanks & U.G.Sump).the Sample should be got approved
Supply and Fixing Dadooing with best quality Ceramic tile of approved make set in C.M 1:3 (1 of Cement : 3 of sand) 12 mm thick and pointing the joints with white cement compound and matching corner tile beading. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportation charges, loading, unloading, chasing of wall for flushing the tile inline with wall surface, preparation of surface, necessary hacking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the departmental officers. Size of Tile - 300 x 600mm x 10mm
Providing dadoing with machine cut polished best quality approved colour granite slab (Synthetic grey, Parasise colour) of thickness not less than 20mm of size 1200x600 / 900x600 mm, set in C.M 1:3 ( 1 of cement : 3 of sand ), thickness not less than 20 mm including pointing with matching colour of Latapoxy SP100 and fixing with stainless steel clamps 6mm dia. and 100 mm long welded with 40 mm and 25 mm long pieces at two ends to right angle, the former with horizontal position to be embedded in brick wall / concrete surface and the later with vertical position to be inserted and caulked in to the holes of the slab, drilled for the purpose, both forming 'T' shape and cement grouted including edge polishing wherever required and forming groove at joints as directed at all levels. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportation charges, loading, unloading, filleting/ chamfering of the edges along with partial recessing of the skirting into masonry, preparation of surface, necessary hacking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over Plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the departmental officers. Rate shall include for preparation of base surface, cleaning, chamfering, edge polishing, with tin-oxide / high gloss factory polish, provision of 'V' shaped notch cuts along the horizontal and vertical joints of specified size as detailed in the drawing protection with Gypsum/POP layer over plastic sheet etc. complete, as directed.
Supply and fixing wall dado with best quality approved make White Glossy ceramic tiles sizes 300 x 300 mm x 6 mm thick set in CM 1:3 (1 of Cement : 3 of sand) 10mm thick and pointing with white cement and as directed. Rate shall include for preparation of base surface, and finishing the surface, cleaning the surface, work at all levels etc. as complete and as directed by the departmental officers (For Over Head Tanks & U.G.Sump) Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportation charges, loading, unloading, preparation of surface, necessary hacking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the departmental officers.
Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.
Special plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers
Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.
Painting the wall with Texture Finish Paint including labour charges complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use).
Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.
Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.
Paving the Top of roof with Solar reflective ceramic tiles of size 305 x 305x 7mm thick of approved quality and colour laid in Cement Mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officer. (The make and brand of the tiles should be got approved by Executive Engineer before use of work).
Supplying & fixing PVC mould CI Steps for Sump etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers.
Manufacturing supplying and fixing in position of teracotta jally 20x20x7.5cm thick approved quality and design in cement slurry including cost of materials labour curing lifting fixing in position etc, complete complying with standard specification and as directed by the departmental officers in all floors.
Supply and installation of Anutone /Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication.
Providing and fixing of 12mm thick Solid compact laminated Urinal Dividers, edge chamfered, melamine coated, scratch & impact resistant. The heat, bacteria, water, chemical and scratch resistant solid compact laminate to be based on thermosetting resins, homogeneously reinforced with cellulose fibres and manufactured as per relevant quality standards. All inclusive with accessories like SS Urinal Wall-Support Brackets, Screws & Wall plugs. URINAL DIVIDERS (Model 1B):Size (Height x Top Width x Bottom Width): 900 x 450 x 400 mm
Brick masonry in CM 1:4 using brick including all varivargams, moulds, sthambams, mukapathrams, koodu, Nasi and all ornamental brick work complete, all pancharams, Agarais, karnakoodus, etc., forming core walls of Rajagopuram/Vimanams complete, including cost and conveyance of all materials including cement, ball the labour charges including marking pathies shaping of the bricks, lifting of all the materials to required heights, curing and all extra for working in heights, etc., complete 100 Cft.
Providing vargapoochu over the core walls of vimanam/gopuram with cm 1:4 complete including shaping the mukhapathram,mahanasi,koodu all ornamental works to proper shape by embedding broken bricks or shaped /chiselled bricks, rough plastering with cm 1:4and finishing with final ornamental plastering and nayam theervai including cost and conveyance of all materials, labour therefore, lifting of materials, all working in heights, curing with water etc., complete including all extra for folding and including clearing the debris from the vimanams/ Gopurams-100sq.ft superficial area.
Supplying and fixing in position best approved of BIS quality 160mm PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.
Supplying and fixing of GM Gate valve heavy duty labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use). Gate Valve
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)
Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works).
Supplying and fixing in position 15mm dia CP Two Way Bib Cock with Health Faucet (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works).
Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).
Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)
Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).
Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)
Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.
Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.
Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.
Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level
Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).
75mm Elbow
75mm Tee
75mm Elbow with Door
75mm Tee with Single Door
75mm Tee with double door
75mm Bend
75mm Y with Door
110mm Elbow
110mm Tee
110mm Elbow with Door
110mm Tee with Single Door
110mm Tee with double door
110mm Bend
110mm Y with Door
Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.
Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position best quality approved make SS sink of size of 600 x 600 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]
Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.
Labour charges for water diviner to point the identification of water level force in below ground level by using the Hydro Geological and Electrical Resistivity Method. The rate is including cost of labour charges, hiring charges for machineries, etc., complete as directed by the departmental officers.
Drilling of bore well any where in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles etc., by first taking a pilot bore of 140 mm / 150 mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site (site will be shown by the departmental officers including construction of mud pit). Upto 60 m depth ending below ground level
Reaming from 140 / 150 mm dia pilot bore to 300 mm dia bore as directed by departmental officer. Upto 60 m depth ending below ground level
Labour charges for inserting PVC casing pipes assembly with slots or with out slots in the drilled hole including the jointing the pipes with PVC couplers with cement paste, etc., complete supply and packing the annular space with pebbles of size and quality as directed by the departmental officer. 160 mm dia casing pipe assembly
Supply the following dia PVC pipe of approved quality 6Kg/cm2 ISI standard etc., complete as directed by departmental officer. 160 mm dia PVC slotted pipe
Charges for developing the bore well with air compressor of 300 cfm capacity (Minimum 8 hours) including transportation labour and fuel charges for compressor as directed by the departmental officers and conducting yield test by 'V' notch method etc., complete.
Supplying and fixing of 32mm dia HDPE pipes for sub mersible pump in bore well class-5 (1 Mpa or 10kg/cm2 pressure) including of cost of HDPE pipes, nylon ropes, labour charges for fixing in position etc., complete as directed by the departmental officers.
Supplying and fixing of following diameter of Stainless Steel Pipe Nipple set for HDPE pipes of good approved quality and with both end portion is threaded for usage of joining purpose including cost of materials, labour charges for fixing, etc., complete complying with standard specification and as directed by the departmental officers.
Supply, delivery, erection and commissioning of 2.0 HP with clear water vertical wet type deep well submersible pump set suitable for 150mm dia borewell of best approval quality with ISI Mark, IS 8034/2002 as amended thereafter and BEE 3 Star Rated capabl
Supply and delivery of direct online starter confirming to IS13947, IEC60947-1 andas amended thereafter with suitable KW rating for operation in AC/ThreePhase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, ThermalOverload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection,Indication lamp, starting capacitor, running capacitor and On/Off Push buttonswitches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulatedcable, powder coated vermin proof box including the capacitor (the cost of capacitoris to be taken separately)
Supplying and laying of PVC insulated and sheathed 4 Core Flat type 16 Sq.mm Copper Cable Confirming to IS 694 / 1990 with ISI mark for 3 phase submerisible pump set including labour charges for laying cables below ground level including earth work excavation
Supplying and laying of L.T. Cables 4 Core 1.1 KV Grade Armoured Aluminium Conductor cable confirming to IS 1554 part I with ISI mark 16 Sqmm cable below ground level including earth work excavation and refilling charges, cost of all material Labour charges.
Supplying and fixing of PVC Insulated and Sheathed 3 Core 2.5 sq.mm Flat Type Copper Cable conforming to IS 694/1990 of good approved quality and brand including cost of materials, labour charges for fixing, etc., complete complying with standard specification and as directed by the departmental officers.
Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E” , bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary etc complete as per standard specification and as directed by the department officers. Make: OMEX / KARTAR/ LIFE GAURD / SAFE GAURD / EQUIVALENT.
Supply, Installation of Fire fighting application 180 degree swinging type, hose reel drum with 20 mm dia braided thermoplastic hose of 30 metres long so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve & open & close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve,including conveyance, all incidental charges, neccessary etc complete as per standard specification and as directed by the department officers. Make: OMEX / KARTAR/ LIFE GAURD / SAFE GAURD / EQUIVALENT.
Supply, and fixing in position of Fire fighting application Hose of 63mm dia of 15mts length binded by copper wire with 63mm dia Stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the department officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffloding and re-doing the dismantled portions to its orginal condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GAURD / EQUIVALENT.
Supply, and fixing in position of Fire fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzie of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Supply of Fire fighting application M.S. Hose Box so that to keep two number of Hose and one number of branch pipe with nozzle. It will have proper glass window type double door with universe open key, painted inside white and outside Post Office red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffloding and re-doing the dismantled portions to its orginal condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GAURD / EQUIVALENT.
Supply, erection, testing and commissioning of MS ‘C’ Class heavy pipe as per IS 1239, to with stand a developing pressure of 10 kg/Sq.cm including necessary fittings like MS flange of table ‘E’, Elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding. Including one coat metal primer and two coat post office red painting including conveyance, all incidental charges, neccessary scaffloding and re-doing the dismantled portions to its orginal condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.
Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT 100mm dia
Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers.
Supply, erection, testing and commissioning of Cast iron body Sluice Valve of 100mm dia at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts and as directed by the departmental officers.
Supply, erection, testing and commissioning of cast iron boday and Gun metal or stainless steel internal Non return valve of 100mm dia to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table 'E', gasket, bolts &nuts , etc. as per IS 5312 including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.
Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.
Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfos or Donfos including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start & auto stop the electrical motor, jockey motor including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: DONFOSS/ INDFOSS/ ISI MAKE / EQUIVALENT.
Supply, erection, testing and commissioning of fire fighting application monoblock motor pump set of 900 LPM at 40 meters head to devolop 3.5 kgs/sq.cm at the heighest and forthest hydrant point to make 30m water jet at the time of fire fighting emergency circumstances, coupled with 11 KW/15 HP rated three phase 414 volts,50 Hz,2880 rpm elctrical motor.the pump with cast iron body, bronze impeller,rope gland packing, suction size of 80mm dia,delivery size of 65mm dia,including the cost of foundation concrete,anti vibration mountig,rain safety hood and etc., complete as directed by the department officers.(Kirloskar make KDS1555+)
Supply and laying of 4 core 10 sqmm armoured copper cable for the power wiring to the Terrace pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the department officers.
Supply and laying of 2 core 1.5 sqmm armoured multi strand aluminium cables for electrical motor, control panel, Pressure Switches, jockey motor etc.. The rate inclusive of all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental officers. Make: POLYCAB / PARACON/ FINOLEX / EQUIVALENT.
Supply, erection, testing and commissioning of Fire fighting 4 way fire brigade inlet with necessary Gun metal 63 mm dia non return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.
Supply, erection, testing and commissioning of Air release valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.
Supply and fixing of stored pressure ABC(Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6kg. Capacity as per IS No. 15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST/ EQUIVALENT
Supply and fixing of carbon-di-oxide Gas type 2 kg capacity Fire Extinguisher as per New IS No. 15683 complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.Make: EXCELLENT / SAFETY FIRST/ EQUIVALENT
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Lower End
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End
Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point (8 points / Coil) Higher End
Supply and fixing of 2x 4' 20W LED fitting with 2 nos. LED tubes on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting
Supply and fixing of 2x 4' 20W LED fitting with 2 nos. LED tubes on conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting
Supply and fixing of 4' 20W LED fitting with LED on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end)
Supply and fixing of 4' 20W LED fitting with LED on conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end)
Supply and fixing of 18W LED square type Recessed / surface fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.
Supply and fixing of 24W LED 2x2 square type Recessed / surface fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.
Supply and fixing of WT Bulk head fitting with guard and 15W LED bulb
supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MSclamps and with painting
supply and fixing of 150W LED Flood light fitting (Higher end) on suitable AI frame support arragnements fixed on roof top parapet wall with PVC unsheathed copper leads with MSclamps and with painting
Supply and fixing of 400mm sweep wall mounting fan fixed on wall with connection complete
Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm fan down rod on exisitng fan clamp
Supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm fan down rod on exisitng fan clamp
Supply and fixing of 300mm (12") sweep (Heavy duty) AC exhaust fan complete without provision of hole in the wall
Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan
Supply and fixing of 450mm (15") sweep (Heavy duty) AC exhaust fan complete without provision of hole in the wall
Supply and fixing of louvers shutters arrangements for 450mm (15") sweep (light duty) AC exhaust fan
Supply and fixing of 2nos.6A two module 3 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End
Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)
Supply and fixing of 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
Supply and fixing of 1 no. 16A module 3 pin socket with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 2 nos.32A 3P MCB, 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming and 1 nos.63A 3P MCB, 9 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 1 nos.40A 3P MCB, 9 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 63A 4P MCCB switch as incoming and 1 nos. 32A 3P MCB, 9 nos. 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End
Supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 100A 4P MCCB switch as incoming and 2 no. 63A 3P MCB, 12 nos. 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End
Supply and fixing of 32A DP MCB in sheet steel enclosure box with electrical connections complete.
Supply and fixing of 32A FP MCB in sheet steel enclosure box with electrical connections complete.
Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm PVC copper wire and making good of the concealed portion with suitable colour.
Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm PVC cu wire and making good of the concealed portion with suitable colour
Supply and Run of 2 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour
Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm PVC cu wire and making good of the concealed portion with suitable colour
Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm PVC cu wire and making good of the concealed portion with suitable colour
Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour
Supply and Laying of 3½ x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
Supply and Laying of 3½ x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
Supply and Laying of 3½ x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
Supply and clamping of 3½ x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 3½ x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 3½ x 150 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 3½ x 185 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 3½ x 240 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 3½ x 25 sq.mm. PVC LTUG armoured cable with suitable size GI pipe on post or on wall with MS clamps
Supply and clamping of 3½ x 50 sq.mm. PVC LTUG armoured cable with suitable size GI pipe on post or on wall with MS clamps
Supply and clamping of 3½ x 240 sq.mm. PVC LTUG armoured cable with suitable size GI pipe on post or on wall with MS clamps
Supply and fixing of brass cable gland for 3½ x 25 sq.mm. PVC armoured LTUG cable with earth connection
Supply and fixing of brass cable gland for 3½ x 50 sq.mm. PVC armoured LTUG cable with earth connection
Supply and fixing of brass cable gland for 3½ x 150 sq.mm. PVC armoured LTUG cable with earth connection
Supply and fixing of brass cable gland for 3½ x 185 sq.mm. PVC armoured LTUG cable with earth connection
Supply and fixing of brass cable gland for 3½ x 240 sq.mm. PVC armoured LTUG cable with earth connection
Supply and providing cable end termination of 3½ x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete
Supply and providing cable end termination of 3½ x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete
Supply and providing cable end termination of 3½ x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete
Supply and providing cable end termination of 3½ x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete
Supply and providing cable end termination of 3½ x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete
Supply ,Erection ,Testing and commissioning of Three compartment LTCT meter box made up of 16 SWG CRCA sheet steel ( Length 1200mm x Height 1200mm x width 600mm) with door and lock & key arrangements on suitable angle iron frame support for floor / wall mounting support with supply and fixing of the following interior mounting arrangements with busbar chamber, meter chamber and Terminal box chamber confirming to IE rules. i.The busbar chamber will consist of 4 nos. 2” x 1/4” tinned copper flat for phase and neutral busbar on epoxy mounted bus insulated at proper and sufficient spacing between the bus bar as per IE Rules. ii. 3 nos. 200/5A CT coil mounted in Three phase busbar. iii. Interconnection between CT coil to 4 way terminal box and 4 way terminal box to Meter box by 4 sq.mm PVC cu.wire. The LTCT meter box should be powder coat paint of approval colour , approved by site officer.
Supply , Erection Testing and commissioning of 415V/50 HZ 400A Cubical panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/2 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 400A TPN switch with disconnector fuse unit (L&T/eq.) -1no, 315A TPN switch with disconnector fuse unit (L&T/eq.) -1no, 200A TPN switch with disconnector fuse unit (L&T/eq.) -1no, 100A TPN switch with disconnector fuse unit (L&T/eq.) -2nos.
Supply , Erection Testing and commissioning of 415V/50 HZ 315A Cubical panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/2 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 315A TPN switch with disconnector fuse unit (L&T/eq.) -1no, 100A TPN switch with disconnector fuse unit (L&T/eq.) -10 nos, 63A TPN switch with disconnector fuse unit (L&T/eq.) -1no.
Supply , Erection Testing and commissioning of 415V/50 HZ 200A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 200A TPN switch with disconnector fuse unit (L&T/eq.) -1no, 63A TPN switch with disconnector fuse unit (L&T/eq.) -5nos
Supply and erection of 40 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 5 stage, (at 0.95 lag), made up of powder coated, 16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters. a. Vr – R phase Line Voltage, b. Vy – Y phase Line Voltage, c. Vb – B phase Line Voltage, d. Ir – R phase Line current, e. Iy – Y phase line current, f. Ib – B phase Line Current, g. KW – Present Kilo Watts, h. RKVA – Present KVAR Demand, i. KVA – Present KVA, j. PF – Present Power Factor, k. Number of Capacitor bank ON/OFF, l. Provision to indicate the imbalanced load, m.Provision to indicate the change in phase Sequence, n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection. Make. (Matrix /L&T /or equivalent
Supply, Erection, Testing, Commissioning and Handing over of 1 No 160 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below with AMF panel. 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 600 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000, The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent), 1. Dry type Air cleaner, 2. Expansion bellow, 3. Radiator, Radiator fan and mounting, 4. Air to air charge cooler, 5. Exhaust Gas turbo charger, 6. Lube oil cooler and Lube oil filter, 7. Fuel filter(pre and micro, 8. In-line Mono-block fuel injection pump with governor and fuel feed pump, 9. Electronic governor, 10. 24V Battery charging alternator, 11. 24V Volt electric starter motor, 12. Engine test Certificate, 13. Residential Mufler, 14. Fly wheel with starter ring, ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator, SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device, 1. Low lubricating oil pressure, 2. High Water temperature, 3. Vee-belt failure and over speed, 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load, 2. ALTERNATOR : Alternator capacity of 160 KVA/ 128 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.), 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt, distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank, The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package, Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade. 4. FUEL TANK : 250 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance, 5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely, coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges.
Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ ceiling with connection (From AMF to 160KVA Genset)
Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulation,
Construction of RCC foundation of size 5500 (L) x2000(B) x 1200mm (H)( 160KVA Gen set weight approximately weight 4500 kg) with cement concert 1:2:4 with sand cushion all around the foundation for the erection of 160 KVA DG set with proper alignment
Provision for Diesel for testing and first running of 160 KVA DG set
Supply and fixing of 400 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry
Supply and installation of maintenance free GI earthing system comprising of 50mm dia and 2 meter long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environmet friendly backfill compound and suitable clamp with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry
Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection.
Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth Connection
Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
Supply and clamping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps
Supply and clamping of 4 x 16 sq.mm. PVC LTUG armoured cable with suitable size GI pipe on post or on wall with MS clamps
Supply and fixing of brass cable gland for 4 x 16 sq.mm. PVC armoured LTUG cable with earth connection
Supply and fixing of 7 Metre Length Double Bracket GI steel tubular Pole with BasePlate (250 x 250 x 6mm) 14.30mmODx5.40mmThick x 4000mm Length, 88.90mm OD x 4.85mm Thick x 1500mm Length, 76.1mmOD x 3.25mm Thick x 1500mm Length with concreting with construction of masonary pedestal with suitable MS box to house one No 20A SP MCB with suitable angle iron frame work with door and with lock and key arrangements and with supply and fixing of 2 nos. 80W LED Street Light Fitting with LED on the above post with PVC unsheathed leads with painting of suitable colour.
Design, Supply, erection, Testing, Commissioning and handing over of Mini Mast Structure (Bajaj / Philips / Crompton make or equivalent) with required number of continuously tapered hot dip galvansied steel polygonal side sections with telescopic strip joints to a total of 12 meters capable of sustaining the maximum wind pressure at the erection site with single flange base mast section with vertically moveable hot dip galvanised lantern carriage and accessories such as electrical junction box brackets for providing 6 Nos of 150W LED flood light luminaries with control gear box complete, head frame assembly, pulley drive stainless steel wire rope single / double drum self-lubricating winch arrangements suitable for raising and lowering the luminaries carraige ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers, and templates including supply and fixing the following accessories in the Mast design and casting of suitable foundation with 1:2:4 mix RCC concreate with 30cm projection above the ground level with 1 mtr width x 1mtr length x 2 mtrs depth with necessary galvanised foundation, bolts nuts and washers and dump plates enclosing the bolts nuts for high mast cosidering the safe soil bearing capacity at site-1 Set, b) High powered power tool with complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V /50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch-1 SET, c) Feeder pillar box comprising of 0.90m x 0.45m x1.20m floor angle iron frame with 63 A power contactor starter for the 3 Phase motor-1Set, d) Neon aviation obstruction light (Bajaj/equivalent) - 1No, e)2Nos of special GI earth electode with copper plate 300 x300x3mm and copper flat (1"x1 1/4")inter connection as per ISS complete with earth connections-1SET, f) Hot dip galvanised lighting arrester- 1 No)
Supply and fixing of Street light controller Panel in suitable 18 SWG MS box with Door and Hinges and Lock and Key Arrangement, comprising the Following such as L&t 4 Pole Contactor MCX-12 63A, CS97014 and Havells 24 Hour Analog Time Switch DHTED30016, 63A FP MCB Incoming with 4.0 Sqmm Copper wire for Control Wiring and painting with one coat of red oxide and 2 coats of synthetic enamel paint. With Necessary Connection.
Supply and installation of 2.0TR capacity 3 star rated energy efficient Hi-wall mounting split type Air-conditioning unit consisting of outdoor condensing unit complete with hermetically sealed Air compressor with R32/R410A refrigerant air cooled condenser ,fan etc., and 1 number indoor unit comprising evaporator unit with cooling coil,blower motor and connected accessories,control etc., with copper refrigerant piping and cord wire connecting indoor and outdoor unit with drain pipe suitable for operation on 230V +/- 10% 50 Hz single phase A.C. supply adhering following norms a) Nominal Cooling capacity -23300 BTU/Hr, b) Air flow rate - 450 CFM, c) Noise level -48 /40/32 db
Supply and installation of 1.5TR capacity 3 star rated energy efficient Hi-wall mounting split type Air-conditioning unit consisting of outdoor condensing unit complete with hermetically sealed Air compressor with R32/R410A refrigerant air cooled condenser ,fan etc., and 1 number indoor unit comprising evaporator unit with cooling coil,blower motor and connected accessories,control etc., with copper refrigerant piping and cord wire connecting indoor and outdoor unit with drain pipe suitable for operation on 230V +/- 10% 50 Hz single phase A.C. supply adhering following norms a) Nominal Cooling capacity -23300 BTU/Hr, b) Air flow rate - 450 CFM, c) Noise level -48/ 40/32 db
Supply and laying of 5/8” and 3/8” copper pipe (beyond 3 mts length)
Supply and fixing of MS stand for fixing out door unit,
Supply and installation of 5 KVA capacity automatic voltage stabliser with time delay relay
Supply and installation of 4 KVA capacity automatic voltage stabliser with time delay relay
supply and fixing of water drain pipe line.(1" PVC drain )
Supply and laying of 3 core 4 sq.mm PVC sheathed copper wire along with copper pipe line
Supply and Installation High quality imaging with 4 MP resolution Dome Camera Water and dust resistant (IP67) and vandal resistant (IK08).Clear imaging even with strong back lighting due to 120 dB WDR.Efficient H.265+ compression technology.EXIR 2.0: advanced infrared technology with40 m long IR range.Support Human and Vehicle Detection.Heartbeat, anti-banding, mirror, password protection, password reset via email, pixel counter.IP67: IEC 60529-2013, IK08: IEC 62262:2002 (Make : Hikvision /Honeywell/ D link/eq.)
Supply and Installation 5 MP IR Fixed Bullet Network Camera High quality ,Excellent low-light performance with powered-by-DarkFighter technology.Efficient H.265+ compression technology.Clear imaging against strong back light due to 120 dB true.WDR technology.Focus on human and vehicle targets classification based on deep learning .Expansive view up to 50m IRdistanceAdvanced streaming technology that enables smooth live view and data self-correcting in poor network Water and dust resistant (IP67).Line crossing detection, intrusion detection, region entrance detection, region exiting detection. (Make : Hikvision /Honeywell/ D link/eq.)
Supply and Installation 4 MP 25× Network IR Speed Dome 360 degree PTZ camera Focuses on human and vehicle targets classification based on deep learning.Support face capture. Up to 5 faces captured at the same time.1/2.8" progressive scan CMOS.High quality imaging with 4 MP resolution.Excellent low-light performance with powered-by-DarkFighter technology.25× optical zoom and 16× digital zoom provide close up views over expansive areas.Expansive night view with up to 100 m IR distance.Support H.265+/H.265 video compression.Digital defog,Line crossing detection, intrusion detection, region entrance detection, region exiting detection, unattended baggage detection, object removal detection, audio exception detection.IP66 (IEC 60529-2013), TVS 6000V lightning protection, surge protection and voltage transient protection. (Make : Hikvision /Honeywell/ D link/eq.)
Supply and Installation of 8 Port Gigabit POE Switch up to 300 m Long range performance may vary depend on camera model or cable condition.6 × gigabit PoE ports, 2 × gigabit Hi-PoE ports, 1 × gigabit RJ45 port, and 1 × gigabit fiber optical port. IEEE 802.3at/af/bt standard for Hi-PoE ports (Max. 90 W PoE output). IEEE 802.3at/af standard for PoE ports (Max. 30 W PoE output).IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3ab, and IEEE 802.3z standard. 6 KV surge protection for PoE ports. Up to 300 m long-range transmission. PoE watchdog to auto detect and restart the cameras that do not respond. Port isolation to improve network security. Gigabit network access design. Wire-speed forwarding. Store-and-forward switching. Solid high-strength metal shell. Reliable fan-free design. UL (UL 60950-1), CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017) (Make : Hikvision /Honeywell/ D link/eq.)
Supply and Installation of 8TB built in Hard Disc Drive. (Higher end )
Supply and Installation of 32 inches LED Monitor 24x7 with following features :LED backlit technology with full HD 1920 x 1080 , 32" LED backlight monitor ; 16.7 million colors display images perfectly ;Multiple interfaces: HDMI, VGA, audio in ; Built-in speaker ; Wide viewing angle: Horizontal 178°, Vertical 178° ; 24/7 operation ; LED backlit technology with full HD 1920×1080 ; 16.7 million color, display picture perfectly ; HDMI support up to 1080P ; Multiple inputs: HDMI, VGA ; Build-in speaker,Audio 5W*2 ; Auto signal input Detection ; Smart engine for Phase/Image position/Color calibration ; Plastic casing ; Narrow front Bezel. (Higer end)
Supply and laying of CAT 6 un armoured cable in exisitng PVC pipe. (Higher end)
Supply and laying of 25mm dia PVC rigid pipe with PVC accessories on wall / ceiling/floor.
Supply and laying of CAT 6 armoured cable in existing HDPE pipe. (Higher end)
Supply and laying of 50/38mm HDPE pipe in a trench to be excavated at a depth of 0.75m and refilling the earth to make good (SD743-cost of 4x6 sq.mm UG cable)
supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement Complete with suitable MS clamps for CCTV with painting of suitable colour
Supply and Installation of Conference Control Unit with Equaliser comprising of knobs at 250Hz, 2kHz and 8kHz, Volume control for Mic 1 input, Volume control for Mic 2 / Aux input Headphone input and volume control Master volume control,Sliding switch for Equaliser On/Off,Supplies power for up to 50 Discussion units,maximum of 25 discussion units to each trunk output in open loop configuration. Make:Bosch/Eq. Model No:CCS700-CCU
Supply and Installation of Conference Chairman Unit with Priority button for chairman microphone,Optional chime tone facility preceding chairman announcements,Modern, unobtrusive styling to match the CCSE-DL Delegate Units,Microphone with flexible stem and light ring,Two headphone sockets.
Supply and Installation of 19 inch length Conference Delegate Unit with Built-in loudspeaker,Built-in volume control for headphones,Controls and Indicators,Microphone on/off button. Rotary volume control for adjusting headphone,Loudspeaker, automatically muted when microphone is on Microphone ‘on’ indicator (red LED) Light ring indicator on microphone stem, lights up red when microphone is on.Make:Bosch/Eq. Model No:CCSE-DL
Supply and Installation of 8 core 1.5 Sq.mm PVC Copper conference Cable with PVC pipe on wall and floor. Make:Bosch/Eq.
Supply and Installation of 250W amplifier with 6 Mic & 2 Aux Inputs, Built-in MP3 player with remote control for USB, SD/MMC card reader Pre amplifier and Line Output for connecting to a Booster Amplifier and for recording the programme. Make:Bosch/Ahuja/Eq.
Supply and Installation of 20W celling mount speaker. Make:Ahuja/Eq.
Supply and Installation of 12U Rack Floor Mount Rack along with cable manager, Power Manager etc.
Supply and Installation of Atlona HDMI & USB Camera designed for video conferencing and applications sus as lecture capture and distance learing HDMI output USB 2.0 interface for video universal PC compatibility through standard UVC 1.1 (USB video class) driver hih performance imaging, fine detail and color rendering with 1/2 8" low-noise, HD CMOS sensor multi element zoom lens with 10X optical zoom and 60.9 horizontal field of view available in black or white. Make : ATLONA Model No: AT-HDVS-CAM-HDMI
Supply and Installation of 55" 4K HDR professional display with 24/7 operation, portrait/tilt, Pro-Mode, Airplay and Chromecast 5K Ultra HD LED Google Tv with Live Colour Technology following features: Usb input, HDMI Port WiFi provision. Make : Sony/FW-55BZ30L.
Supply and Installation of Heavy Duty Movable Floor mount slope Stand for LED TV suitable upto 75 inch with wheels. Make:Jenefas/Eq.
Supply and Installation of 1 in 8 out HDMI Splitter. Make : Milestone/Eq.
Supply and Installation of 30W wall mount speaker.Make:Bosch/Eq. Model No:LB2-UC30-L1
Supply and Installation of 200 + 200 Watts two zone power mixer 6 Mic & Aux input speaker output 4 ohms. 8 ohms & 16 ohms & 70 & 100 Volt Amplifier Make : Ahuja/Eq Model No : TZA400EM
Supply and Installation of 16 Channel analog mixer the console in built using tour grade robust metal construction and top quality components and has an internal universal power supply. Make : Sound craft/Eq. Model No : U16.
Supply and Installation of wooden podium is ideal for class rooms, 22" x 15.4" top and 5.5." tall walls for base is 20" x 13.3 " Make : Custom.
Supply and Installation of gooseneck microphone for podium with base 20m extension mic cable 48V phantom power supply. Make : Ahuja/Eq. Model No : GMB6C + GM615.
Supply and Installation of UHF wireless handled PL22 microphone with touch on/off button. Make : AKG/Eq. Model No : WMS 40 MINI2.
Supply and Installation of 20 Mtr Extension Mic cable with moulded XLR male and female connectors. Make : MX.
Supply and Installation of Beta 58A The Shure Beta 58A is a handheld supercardioid dynamic microphone offering enhanced midrange and controlled proximity effect for optimal reproduction of vocals, speech, and instruments in concerts, public address, houses of worship, and live stage applications. Its dynamic capsule utilizes a neodymium magnet for high signal-to-noise. Make : Shure/Eq.
Supply and Installation of 1KVA Voltage Stabilizer with Input A/C 160-260V output 230V Make : Studiomaster/Eq.
Supply and Installation of micropone floor stand. Make : Ahuja/Eq. Model No: AFS 201.
Supply and Installation of microphone test stand. Make : Ahuja/Eq. Model No : ATS5.
Supply and Installation of microphone table stand. Make : Ahuja/Eq. Model No: ATS 200.
Supply and Installation of audio board with 6 channel XLR microphone socket. Make : Custom.
Supply and Installation of LED Projector 5000 ANSI Lumens, WUXGA (1920 X 1200) 20000 Hrs, HDMI, DVI-D, VGA, LAL, RS-232C, VGA Out, HD bast T, Audio in & Out.
Supply and Installation of Heavy Duty Celling Mount Kit + Exp rod 3/6 ft up to 50Kg. Make : Logic/Eq.
Supply and Installation of 12 x 9 Tubular Motorized screen with RF Remote. Make : Logic/Eq.
Supply and Installation of 2 core 1.5 Sq.mm Speaker cable with pvc pipe on wall and ceiling. Make:Orbit/Eq.
Supply and Installation of HDMI 20 mtrs cable with connectors.
Supply and run of 3 core 1.5 sqmm power cable with PVC pipe for projectors. Make : Orbit/Eq.
Supply and Installation of 15U floor standing rack with power sockts and lock & key facilities. 700mm width x 600mm deot tray steel audio equipments rack which consists of power sockets, Lock - key front glass door, rear metal door with caster's set and other accessories.
Testing and Commissioning of PA System amplifier, speaker, cordless mic, HDMI cables and other necessary accessories etc.
Supply and installation of 1 loop analogue addressable fire alarm panel, with 16 fire zone indicators, 40 character backlit LCD, 2 independent sounder circuits, Sound Alarms, Silence/Resound, Mute Buzzer, Accept, Reset buttons, 12 button alpha numeric key pad and 4 cursor keys, Fire, Fault, Test, Disablement, Delayed Mode, Alarms Silenced, Buzzer Muted, Sounders Disabled, Relays Disabled, Power, Supply Fault, CPU Fault, Sounder, Fault and Earth Fault indicators, inbuilt battery charger with 2 x 7 AH, 12 volts battery. With 485 Communication port
Supply and installation of analogue addressable smoke detector photoelectric type with base, JB and led to operate on 24 v dc supply.
Supply and installation of Heat Detector with base , JB etc
Supply & installation of Fault Isolators Modules
Supply & installation of addressable input/output control module interface units
Supply and installation of addressable electronic sounders cum strobe wall mounting type.
Supply and Installation of Addressable manual call points press type
Supply and installation of 2 core x 1.5 sqmm copper Armoured cable fixed on wall or ceiling with clamps, screw. (Quotation)
Supply & installation of power supply unit which provides 24 V dc output
Supply and Installation of ABC type Dry Chemical Powder Fire Extinguishers, cylindrical in shape, Wall mounted type, with initial charge. Capacity 6 kgs
Supply and installation of RJ 45 i/o socket with module box and phase plate. Combo D-RJ45 CAT6E Lan I/O Network Keystone Jack, Gang Box, Single Port Face PlateType: 1x Keystone Jack + 1x Gang Box + 1x Single Socket Face Plate Suitable for : CAT6 / CAT6E(Higer end)
Supply and installation of 8 port 10/100/1000 Mbps fully managed layer -2 switch with 1G uplink,24 x 10/100/1000 BASE-T ports Fanless design for silent operation Innovative Green energy saving features Complete web interface for comprehensive switch management. (Higher end)
Supply and installation of 24 port 10/100/1000 Mbps fully managed layer -2 switch with 1G uplink,24 x 10/100/1000 BASE-T ports Fanless design for silent operation Innovative Green energy saving features Complete web interface for comprehensive switch management. (Higher end)
Supply and installation of 48 port 10/100/1000 Mbps fully managed layer -2 switch with 1G uplink,24 x 10/100/1000 BASE-T ports Fanless design for silent operation Innovative Green energy saving features Complete web interface for comprehensive switch management. (Higher end)
Supply and installation of 8 port patch panel -fully loaded 6 patch panels are six port RJ45 modules applied and suitable for 22-26 AWG stranded and solid wire, compatible with both 110 & Krone punch down tools. patch panels have improved Cable Management with optional Cable Management bar terminating 4 pairs UTP cable. (Higher end)
Supply and installation of 24 port patch panel -fully loaded. 6 patch panels are six port RJ45 modules applied and suitable for 22-26 AWG stranded and solid wire, compatible with both 110 & Krone punch down tools. patch panels have improved Cable Management with optional Cable Management bar terminating 4 pairs UTP cable. (Higher end)
Supply and installation of 48 port patch panel -fully loaded. 6 patch panels are six port RJ45 modules applied and suitable for 22-26 AWG stranded and solid wire, compatible with both 110 & Krone punch down tools. patch panels have improved Cable Management with optional Cable Management bar terminating 4 pairs UTP cable. (Higher end)
Supply and installation of 4U wall rack with power sockets, cable manager with 0.6 KVA UPS all accessories. (Higher end)
Supply and installation of 6U wall rack with power sockets, cable manager with 0.6 KVA UPS all accessories. (Higher end)
Supply and installation of 12U wall rack with power sockets, cable manager with 0.6 KVA UPS all accessories. (Higher end)
Supply and installation of 1 mtr. patch cord. (Higher end)
Supply and installation of 2 mtr. patch cord. (Higher end)
Supply of Early Streamer Emission Air Terminal (ESEAT). Model: HAVING corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. hazardous atmosphere. The Air terminal is non-radioactive and requires no special licensing. The unit is fully, autonomous (no battery, no external power supply is required), collects energy from the ambient electric field.The ESEAT model hasbeen tested in a high voltage laboratory in accordance with NFC 17 102 in order to measure the average gain in triggering, The average gain in triggering time (∆Ts) obtained during the lab test for the offered model is 60 µs. The ESEAT works on negative as wellas positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is avilable to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause 8.6 of the Revised NFC 17-102 version 2011 ). ESEAT Model : L - Radius of protection : 86 Metres Level of protection considered for the Project-II level.
Supply and Instllation of standard / special mounting structure of height 4.5mts pipe and 300x 300x 8mm Ms plate,3mts.48mm OD class C GI outer pipe ,1.8mtr.38mm OD inner pipe for roof mounting on concrete base with FRP adapter.
Supply and run of 25mm x 6mm GI Flat DownCondutor with necessary clamps / supports on wall / floor / ground for earth connection.
Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance
Supply and installation of maintenance free GI earthing system comprising of 50mm dia and 2 mtr. Long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs carbon based environment friendly backfill compound and suitable clamp
Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and over voltages in the power line due to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective building in parallel to the power circuit.
Supply and fixing of 100A four pole MCCB in suitable sheet steel enclosure with earth connection
Sub Total
Rajam Engineering Contractors (BID ID -1053415)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid