Addn/Altn in bldg No P-05 OTM Accn at Tibri Mil Stn under GE Gurdaspur.

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer.

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified and directed.

Roughening the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate even and smooth without using extra cement using complete all as specified and directed.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed complete all as specified and directed and all as per manufacturer's instructions.

M&L for 40mm thick brick tile laid over 15mm thick bedding layer in grouting CM(1:6) and pointing with CM (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer-in-Charge.

All a per Srl item No 07 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 01 shall be reused after necessary cleaning of mortar)

M&L for PCC 1:2:4 type B0 (using 12.50mm graded stone agg) as in roof kerbs, kerb, coping etc. complete all as specified and directed.

Supply only integral water proofing compound.

Demolition of cement concrete above ground floor and in any position as sunken etc.

M&L for 15mm thick cement screed in CM 1:3 admixed with integral water proofing compound FOSROC conplast X421IC @ 130ml per bag of cement incl a bonding coat of FOSROC Nitobond AR cement slurry coat (1 vol of Nitobond AR+ 1.5 Vol of water+ 1.5 Vol of cement) complete all as specified.

M&L for applying two coats of Nitobond SBR cement slurry (1 Vol of Nitobond SBR+ 1 Vol of water+ 3 Vol of cement) water proofing coating on the entire surface of sunken portion all as specified.

M&L for PCC 1:5:10 type E2 using 40 mm stone agg filling fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level

Material and labour cement concrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection thickness of 75mm finishing the surface even and fair with joints to full depth at corners, along the wall and @ 3 meters c/c filled with mastic mortar complete all as specified

M& L Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 and including demolition of existing tiles and screed complete all as spcified and directed by EIC.

M&L for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles including demolition of existing tiles and screed complete all as speciifed and directed by EIC.

Demolition Stone slabs and tiles of any description or thickness in floors, aprons, counter platforms etc.

M & L for Green Marble work 16-18 mm thick (table rubbed and polished) in steps, jambs, Shelves, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl 20 mm thick cement screed bed in cm 1:6 complete all as specified and directed.

Demolition of cement concrete (Reinforcment) as Fascia, projection, chajja, parapet, shelves etc of any description incl cutting of reinforcementt of chajja, fascia, parapet, projection, shelves etc. with neccessary scaffolding upto 12m ht of bldg complete all as specified and directed by Engr-in-charge. Note: - Cost of scaffoldings, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs upto 12m height all as specified and directed.

M&L TMT bars 6 to 8mm dia cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed not less than 0.9mm dia complete all as specified and directed.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work complete all as specified and directed.

Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of walls, finished surface even and fair with WPC, upto height 12m complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

M&L preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of primer on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of cement base paint of wall complete all as specified and directed.

M&L for Preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing surfaces and applying two coats of oil bound distemper on wall complete all as specified and directed.

M&L for Preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing surfaces and applying two coats of white wash on wall complete all as specified and directed.

M&L for Preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment, Preparation of old surface and applying two coats of cement base paint on wall complete all as specified and directed.

M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint ht upto 12m complete all as specified and directed.

M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats and removing to store complete all as specified and directed.

All as per Srl item No 40 above but exc 1.50sqm but n.exc 4.00 Sqm.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and drawing complete all as specified and directed.

S&F 30mm thick factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to e fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 105x60mm all as spd including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:2:4 (type-B0) in the frames complete all as specified and directed.

S&F 35 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm with IS Marked with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Aluminium anodized barel tower bolt of extruded section 150mm long with ISI marked complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long with ISI Marked complete all as specified and directed.

S&F 100mm size extruded aluminium alloy butt hinge with galvanised mild steel hinge pin type B-21 fixed with metal surface through screw with ISI Marked complete all as specified and directed.

S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 incl one shop coat of priming and two coat of synthetic enamel paint and taking down old existing window complete: :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately

S&F Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 incuding cutting and making good dismantled portion in PCC 1:2:4 type B-1incl one shop coat of priming and two coat of synthetic enamel paint and taking down old existing window complete all as specified and directed. Note : Sheet glass and wiremesh shall be measured and paid separately

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed.

S&F 4mm thick Figured ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from steel frame complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

Re-fixing old steel tubing including fittings 15mm bore in new or old position including cleaning the same incl taking down complete all as specified and directed

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

Re-fixing old steel tubing including fittings 20mm bore in new or old position including cleaning the same incl taking down complete all as specified and directed

S&F GI tubing 32mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings for spout complete all as specified and directed.

S&F rotational moulded polytheylene white triple layered white water storage tanks, ISI marked of capacity 1000 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with polythene float and flynut complete all as specified.

S&F in repair Gun-metal, globe or gate valves, 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair bib taps (long nose) cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make:- Prayag (Cat No. 7506), ESS ESS Cat No DS-02A or equivalent or equivalent

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. Make:- Prayag (Cat No. 7510), ESS ESS Cat No DS-04A or equivalent or equivalent

S&F in repair Pillar taps (long nose), cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed. Make:- Prayag (Cat No. 7502), ESS ESS Cat No DS-01A or equivalent or equivalent or equivalent.

S&F in repair brass CP shower rose 125 mm size with 225mm arm swivel joint fancy type complete all as specified and directed.

S&F Stainless steel tubular 20 mm dia towel rail 60 cm long fixed to wall complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve, and 32mm bore PVC flush pipe etc complete all as specified and directed.

S&F SS Soap dish, oval type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repair for Vitreous China wash down water closet pan (pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat white with stainless steel jet spray, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap complete all as specified and directed.

S&F in repair Vitreous China urinals, half stall type minimum size 345X320X560 mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including PTMT Urinal spreader 60mm long brass screws, pointing around urinal back in cement and 32mm dia PTMT waste coupling with 32mm dia pipe complete all as speciifed and directed.

S&F in repair Vitreous china counter top oval wash basin, white, size 550x400mm, including 32mm dia CP brass waste coupling with 32 mm dia waste pipe complete all as specified and directed.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches, if required.

S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC(SWR) branch piece single(single Y) equal or unequal 110mm bore with oval access door complete all as specified and directed.

S&F in repair PVC (SWR ) bends, oval acess door 110 mm bore any radius complete all as specified and directed.

S&F in repair PVC (SWR) Double junction (double-T Cross) 110 mm bore equal or unequal with oval access door

S&F in repair PVC (SWR ) vent cowl 110 mm bore

M&L in repair PVC(SWR) floor trap incl jointing with solvent cement 100mm dia complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc.

M&L for brick work with fly ash brick, straight or curved on plan exc 6m mean radius built in CM 1:6 brick in fixed complete all as spcified and directed by EIC.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof/wall coverings/crumple joints complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick, ISI marked any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, crumple joint etc. fixed with self tapping screws as specified etc. as required complete all as specified and directed by EIC.

S&F machine cut kota stone slab flooring 20-22mm thick size 600X600mm over cement screed base 15mm thick in 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) in floor, stair, skirting etc. complete all as specified and directed by Engineer-in-Charge.

Labour only grinding of existing machine cut kota stone slab flooring including rubbing and polishing complete .

Supply and fixing cutrain rod 20mm dia of Mild steel with PVC coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F in repair Stainless steel cockroach trap with hole, round 101mm dia complete all as specified and directed. Make:- Prayag (Cat No. FT-21 M) or equivalent.

M& L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exc 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified.

S&F Pre-painted galvantume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick , ISI Marked of any colour having tensile strength of 550 Mpa as in chajjas, projection etc and like, incl cutting, rounding etc and finished look good ,fixed with self tapping screws complete all as specified and ditected by Engr in charge. Note: - Cost of scaffoldings, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in Roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (Beam, tee, angle, Coulmn, Gusset Plates, channel, Hollow square/Rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge. Note: - Cost of scaffoldings, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC unsheathed multistranded FRLS copper conductor cable of size 1.5 Sqmm including concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 Sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way switch

All as per Srl item No 99 above but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 99 above but 5 amps socket outlet on independent board.

All as per Srl item No.99 here-in-before but one light point controlled by two way switches.

All as per Srl item No.99 here-in-before but wiring with 2.5 Sqmm FRLS copper wire including one earth wire 2.5 sqmm of copper for 15 Amps 3 pin socket outlet .

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt, FRLS cable of size 6 sqmm including 6 sqmm (Red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2mm thick and 32mm wide and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly complete and taking down old unsedrviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing colour with MES approval make of distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type.

S&F switch flush type 15 amps single pole one way

S&F socket outlet 3 pin 15 amps flush type

S&F switch piano 2 way 5A all as specified and directed.

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitabe for and upto 1 x 18/20W LED tube rod in taking down old unserviceable fitting complete all as specified and directed.

S&F LED tube light 20W ultra bright LED polycarbonate tube light with very high efficacy suitable for fitting into tube light batten fitting complete all as as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report from manufacturer to Engineer-in-Charge before incorporating the items in work.

Taking down carefully ceiling fan complete fittings at site, removing fans are deposting to MES store yard and refixing after completeion of work at the site.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to connector to fan complete including replacement of one pair of canopy.

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as specified and directed.

S&F Bell, AC, 230 volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amp complete all as specified and directed.

S&F in repair lamp holder PVC body angle type including 9 watt LED bulb polycarbonate body with back plate complete all as specified and as directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate isolated body.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm dia and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nut & bolts, washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts & bolts etc complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supplying and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. Note : All the connection of incoming and out goiing wire in MCB will be made with thimble with suitable size as directed.

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

All as per Srl item No 122 above but single pole and neutral 40 amps.

Material and labour for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed. (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar 200 amp rated made out of Aluminium on insulated duly insulated wire adhesive tape RYB & black-4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable sizeas directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54cm x 54cm x 5cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil including dismantling existing complete all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete al as specified and directed.

Excavation in trenches in soft and loose soil including cutting road surfaces not exc 1.5 mtr wide and not exc 1.5 mtr in depth for poles, stay, cable, pipe etc getting out complete all as specified and directed.

Returning, filling including spreading and well ramming in layers each not exc 25 cm thick in soft loose soil all as specified and directed.

Removing excavation material exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

Supply and lay brick common burnt sub class 'B' old size and for protection of cable laid in trenches for under ground cable complete all as specified and directed.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable and 8cm after laying the cable complete all as specified.

S&F in repair indoor type decorative recess mounted direct/ indrect 2'x2' luminaries light fixures made upto 36 watt LED netural white complete including making connection with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make :- Havells/ Crompton/ Wipro.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

MALKIT SINGH AND SONS (BID ID -3195551)

VOHRA CONSTRUCTION CO (BID ID -3196234)